display AUDI A5 CABRIOLET 2010 User Guide

Driver information displ ay
Digital speedometer
Fig. 11 Display:
Di gital speedomet er
Current speed appears in the display. Speed is shown in 1 mph incre­
ments (USA models) or 1 km/h increments (Canada models).
You ca n sw itch the display from miles to kilometers and vice versa via
the MMI. •
Open door or trunk lid warning
The pictogram alerts you when doors or the trunk lid have
been left open.
Fig. 12 Disp lay : O pen
door- and tr unk li d
w arni ng
The Open Door/Trunk lid warning d isplays if even one door, the hood
or the trunk lid is open. This symbol also shows
which door or lid has
not been closed=> fig. 12.
As soon as the door, the hood and the trunk lid are closed properly, the door and trunk lid warn ing tu rns off and the selected dr iver info r­
mation system functions are displayed again .•
Service interval display
The service interval display reminds you when your next
service is due.
Fig. 13 Display:
S ervic e in te rva l d isp lay
The schedule for the next oil change or inspection is calculated auto ­
matically and displayed accordingly . The disp lay works in two stages :
Service remind er
30 days before the next serv ice is due , a serv ice reminder appears in
the display when you turn on the ignition=> fig. 13.
After abo ut S seconds the d isp lay switches back to norma l. The
distance and time remaining are updated each t ime the ignition is
turned on until the date due for service is reached.
Ser vice due
When the due date for service is reached, the message Servic e due !
appears in the instrument cluster immediately after you turn on the ..,,

ignition. Additionally, a warning tone sounds. After about S seconds
the display switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due, can be shown in the
radio or MMI* display by selecting the service interval display in the
car menu. Select
I CAR]> Service interval display .
Resetting the service interval display
Your authorized Audi dealer will reset the corresponding service
schedule after performing the appropriate service on your vehicle.
You also have the possibility to reset the oil change schedule after
having performed an oil change according to Audi specifications .
Select
I CAR]> Service interval display > Reset oil change interval.
0 Note
If you disconnect the battery termina ls, no calculat ions can be made
for the serv ice interval display dur ing this time and no service
reminder will appear. Remember that observing the proper service
intervals is vitally important to extending the life of your veh icle,
particularly the engine, and maintaining its value . Even if the mileage
dr iven is low, the maximum period of one year from one service to the
next must not be exceeded.
[ i J Tips
• Do not reset the display between oil changes, otherwise the
display will be incorrect.
• The information in the Service Reminder remains stored even
when the vehicle battery is disconnected .•
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Driver information display
On-Board Diagnostic system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunct ion Indicator Lamp (MIL) in the instrument cluster
=>
page 12, fig. 7 is part of the On-Board Diagnostic (OBD II) system.
Th e warning/indicator light illuminates when the ignition is switched
on and goes out after the engine starts and the idle has stabilized.
This indicates that the MIL is working properly.
If the light does not go out after the engine is started, or illuminates
whi le you are driving, a malfunction may exist in the engine system.
If the light illuminates, the catalytic converter could be damaged.
Continue driving
with reduced power (avoiding sustained high
speeds and/or rapid accelerat ions) and have the condition corrected.
Contact your authorized Aud i dealer .
If the light illuminates, the electronic speed limiter may also be
malfunction ing. For more information=>
page 22, "Electronic speed
limiter".
An improperly closed fuel filler cap may also cause the MIL light to
illuminate
=> page 2 76. •
On-Board Diagnostics
Fig. 14 Location of
Data Link Connector
(DLC)
tJ,,,
Vehicle care Do-it-yourselt service iTechnical data

Driver information display
On-Board Diagnostics monitors the components of your emission
control system. Each monitored component in your engine system
has been assigned a code . In case of a malfunction, the component
will be identified and the fault stored as a code in the control module
memory .
The MIL light may also illuminate if there is a leak in the on-board fuel
vapor recovery system. If the light i llumi nates after a refueling , stop
the vehicle and make sure the fuel filler cap is properly closed
=> page 276.
In order to make an accurate diagnosis, the stored data can only be
displayed using special diagnostic equipment (generic scan too l for
OBD).
In order to connect the special diagnostic equipment, push the plug
into the Data Link Connector (DLC). The DLC is located to the right of
the hood release
=> page 21, fig. 14.
Your authorized Audi dea ler or qualified workshop can interpret the
code and perform the necessary repair. •
Electronic speed limiter
Your vehicle may be factory equipped with tires that are rated for a
maximum speed of 130 mph (210 km/h). This is less than the
maximum speed of your veh icle. To reduce the risk of sudden t ire
fai lure and loss of control if the vehicle is operated at excessive
speeds, your vehicle also has an electronic speed limiter. The elec­
tronic speed limiter prevents your vehicle from going faster than the
tire speed rating. For more information=>
page 307.
If the engine control unit receives faulty vehicle road speed signals,
the Malfunction Ind icator Lamp (M IL) will illuminate. If this
occurs , contact the nearest authorized Audi dealer for assistance .
& WARNING
Always observe the posted speed limits and adjust your speed to
suit prevailing road, traffic and weather conditions. Never drive
your vehicle faster than the maximum speed rating of the tires
installed. •
Trip computer
Introduction
The trip computer gives you information on current and
average fuel mileage, average speed, fuel range and
driving time.
Fig. 15 Trip computer
display: Fuel range
Fig. 16 Trip computer
display: Average fuel
mi~age
~

The following information is continuously evaluated by the trip
computer and can be displayed sequentially in the instrument cluster
display:
Fuel range
The estimated cruising range in miles (km) appears in the display .
This tells you how far your vehicle will be able to travel on the current
tank of fuel and with the same driving style . The display changes in
increments of 6 miles (10 km).
The cruising range is calculated based on the fuel consumption for
the last 18 miles (30 km). If you drive conservatively, the cruising
range will increase.
Average fuel mileage
The average fuel economy in MPG (l/100 km) s ince you last cleared
the memory appears in this disp lay. You can use this display to adjust
your dr iv ing techn ique to ach ieve a desired mileage.
Current fuel mileage
The instantaneous fuel consumption in miles per ga llon {l/100 km) is
shown in this display. You can use this display to adjust your driving
technique to achieve a desired mileage .
Fuel consumption is recalculated at intervals of 33 yards (30 meters).
This display switch es to gallons/hour (liters/hour) when the vehicle is
not moving .
Average speed
The average speed in mph (km/h) since the last time the display was
reset appears in the display.
Elapsed time
Th e length of time that you have been driving since you last reset the
memory appears in this display.
Distance
The d istance that has been covered since the last time the memory
was cleared appears in the display .
Controls and equip ­
ment Safety first
Driver information display
(I] Tips
•
Fuel consumptions (average and current), range and speed are
displayed in metric units on Canadian models .
• All stored values will be lost if the vehicle battery is
disconnected. •
Memories
The trip computer is equipped with two fully automatic
memones.
Radio WXRK
Fig. 17 Trip computer
display: memory level
1
You can switch between the trip computer 1 and 2 by pressing the
Reset button @=>
page 24, fig. 18 .
You can tell which memory level is currently active by the number in
the display => fig. 17. The data from the single-trip memory (memory
level 1) is being displayed if a
1 appears in the display . If a 2 is shown,
t hen the data from the total-trip memory is being displayed (memory
level 2) .
Single-trip memory (Trip computer 1)
The sing le-trip memory stores the trip information from the t ime the
ignition is turned on until it is turned off. If the trip is continued
within 2 hours from the time the ignit ion was turned off, the new
data will be included in the calculation of the current trip informa-
I,,,
Vehicle care Technical data

Driver information display
tion. If the trip is interrupted for more than 2 hours the memory is
reset automatically.
Total-trip memory (Trip computer 2)
Unlike the single-trip memory, the total-trip memory is not reset
automatically. Th is permits you to evaluate your driving data for the
entire pe riod between manual resets. •
Operation
The trip computer is controlled by two switches on the
windshield wiper lever.
Fig. 18 Windshield
wiper l ev er : controls
for th e trip comput er
- Pushthefunctionselectorswitchupordown @~fig.18 .
This will cause the five distinct trip computer functions to
be displayed one after another.
The trip computer will not operate unless the ignition is on. When you
turn on the ignition, the function that was in use when yo u last tu rned
the ignition off will be d isplayed.
In addition to information on the on-board computer (on-board
computer 1 or 2), the dig ital speedometer a nd information regarding
the navigation system* can also be displayed. To switch the display
between the different information, tap the Reset button@ briefly.
Setting values to zero
To delete one current value from the trip computer, select the
desired function and press the Reset button @ for at least one
second. The following values can be set to zero
individually using the
Reset button:
• Average fuel mileage
• Average speed
• Elapsed time
• Distance
In addition,
all the values in the single-trip or the total-trip memory
can be deleted simultaneously=>
page 24.
[ i ] Tips
All stored values will be lost if the vehicle battery is disconnected. •
Basic Settings for the trip computer
The MMI* or the radio operating unit is used for setting
the trip computer's basic settings .
-Select: Function button [CARI> Instrument cluster > On-
board computer 1
or On-board computer 2.
Th e values in the single-trip or the total-trip memory can all be reset
to zero at the same time under
Reset in the menu.
In addition, you can determine what information from the trip
computer should be shown in the instrument cluster display. If one
of the pieces of driver information is turned
off , that driver informa­
tion will not be shown in the display. The info rmation w ill continue to
be calculated by the trip computer and can be turned back
on at any
time. •

Speed warning system
Overview
The speed warning system helps you to keep your driving
speed below a set speed limit.
The speed warning system warns if the driver exceeds a previously
stored maximum speed. A warning tone will sound as soon as the
vehicle speed exceeds the set speed by about 3 mph (3 km/h) . At the
same time, a warning symbol appears in the display. The symbol 's
appearance might be different in some models .
The speed warning system has
two warning thresholds that function
independently of each other and that have somewhat different
purposes:
Speed warning 1
You can use speed warning 1 to set the maximum speed while you are
driving. This setting w ill remain in effect until you turn off the igni­
tion, assuming that you have not changed or reset the setting .
The speed warning symbo l
0 (USA models)/0 (Canada mode ls) in
the warning 1 display appears when you exceed the maximum speed .
It goes out when the speed falls be low the stored maximum speed.
The speed warning symbol will also go out if the speed
exceeds the
stored maximum speed by more than about 25 mph
(40 km/h) for at
least
10 seconds. The stored maximum speed is deleted.
Setting speed warning 1
=> page 25.
Speed warning 2
Storing warning 2 is recommended if you always want to be reminded
of a certain speed, for example when you are travel ing in a country
that has a general maximum speed limit, or if you do not want to
exceed a specified speed for winter tires.
The speed warning 2 symbol,
8, (USA models)/ 8, (Canada models)
appears in the display when you exceed the stored speed limit. Unlike
Contro ls a nd e quip ­
m en t Vehicle
OP-eration
Driver information display
warning 1, it will not go out until the vehicle speed drops below the
stored speed limit.
Setting speed warning 2
=> page 26 .
(I) Tips
Even though your veh icle is equipped with a speed warn ing system,
you should still watch the speedometer to make sure you are not
dr iv ing faster than the speed limit.•
Speed warning 1 : setting a speed limit
Warning threshold 1 is set by the [SET] button.
Fig. 19 SET button in
the instru men t cluster
Storing the maximum speed
- Drive at the desired maximum speed.
- Press the
[SETI button in the instrument panel display
~ fig. 19 for 1 second .
Resetting the maximum speed
-Drive the vehicle at a speed of at least 3 mph (5 km/h)
- Press the
[SET) button for more than 2 seconds .
Vehicle care Do-it-yourselt service iTechnical data

Driver information display
The speed warning symbol '8 (USA models) /8 (Canada models) will
appear briefly in the display when you release the
I SETJ button to
indicate that the maximum speed has been stored successfully .
The maximum speed remains stored until it is changed by pressing
the
I SETJ button again briefly or until it is deleted by a lengthy push
on the button .•
Speed warning 2: setting a speed limit
The /11/111* or the radio control unit is used to set, change
or delete warning threshold 2.
- Select: Function button I CAR]> Instrument cluster>
Speed warning.
• Speed warning -the warning threshold can be turned on or off .
• Speed warning -a warning tone will sound if you exceed the speed
you have set.
Warning threshold 2 can be set in the speed range starting from
18
mph to 150 mph (30 km/h to 240 km/h). Settings can each be
adjusted in intervals of 6 mph (10 km/h). •
Auto Check Control
Introduction
The Auto-Check control monitors the function of certain vehicle
features and components. It simply makes sure these features and
components are working properly. The Auto-Check control works as
long as the ignition is on, as well as whenever the veh icle is driven.
If a component is malfunctioning or if the need for an urgent repair
has been detected, this will appear in the instrument cluster display.
You will also hear an audible warning tone. The displays are color
coded in e ither red or yellow depend ing on their level of priority . A
red symbol means
Danger, a yellow symbol indicates Warning . In
certain situations, information message for the driver appear in addi­
tion to the red and yellow symbols.
Th e Auto-Check Contro l will automatically perform a test each time
you switch on the ignition. With the selector lever in
P or N, the
following message appears in the display:
When stationary apply footbrake while selecting gear.
When you a select a different gear (for example: R, D, etc.), the
message will disappear and the Auto-Check function is displayed.
If there is a malf unction, then the malfunction message will appear
about 15 seconds after you start the vehicle. At the same time you
w ill hear a wa rning tone. •
Driver information messages
Driver information messages are shown in the instru­
ment cluster display in addition to symbols.
Fig. 20 Instrument
cluster: SET button
For examp le, if the transmission selector lever is not in the P position
when the eng ine is turned off, the following message appears:
Shift to P , otherwise vehicle can roll away. Doors do not lock if
lever is not in P. .,._

The ignition key can only be removed with the selector in this posi­
tion. This and other messages are brought up if a function cannot be
carried out.
Driver messages and red symbols
If a red symbol appears in the display, a driver message is also
displayed automatically.
For example, the symbol for a problem with engine oil pressure
't=r.
appears in the display . The message:
Switch off engine ! Oil pressure too low
The driver message in the display goes out after about 5 seconds. The
driver message can be displayed again by briefly pressing the
!SET]
button~ page 26, fig. 20.
Driver messages and yellow symbols
If a yellow symbol appears in the display, a driver message is also
displayed automatically .
For example, the symbo l appears in the display, ind icating low
windshield washer fluid level. The following message also appears:
Please refill washer fluid
The driver message disappears after a few seconds. The driver
message can be displayed again by briefly pressing the
!SET]
button. •
Controls and equip ­
ment Safety first
Driver information display
Red symbols
A red symbol means DANCER.
Fig. 21 Display:
Danger symbol
- Pull off the road.
- Stop the vehicle.
- Turn off the engine.
- Check the malfunctioning system . Contact your autho-
rized Audi dealer or a qualified workshop for assistance.
Red symbols ind icate a priority 1 malfunction -Danger!
With a priority 1 malfunction, a red symbol appears in the upper
center area of the display~ fig. 21. A driver message appears as well
to expla in the malfunction in more detail. When this symbol appears,
three warning tones sound in succession. The symbol continues to
flash until the fault has been corrected .
If
several prior ity 1 ma lfunctions are present, the symbo ls appear in
succession and remain for about 2 seconds.
Th e driver warning goes o ut after about 5 seconds, but it can be
brought up again at any time by pressing the
!SET I button. ~ page 26.,..
Vehicle care Technical data

Driver information display
0 Alternator failure => page 28
BRAKE
USA models: ::::>page28
Brake system malfunction

Canada models: ::::>page28
Brake system malfunction
4.
Engine coolant level too ::::>page29
low/engine coolant temperature
too high
II
~ Engine oil pressure too low =:>page 30
~,. Refill engine oil now =:> page 30
@-e Steering malfunction => page 31
©-1 Ignition lock malfunction II=> page 31
Alternator malfunction D
If the O symbol in the instrument panel display flashes, then there
is a malfunction in the alt ernator or the vehicle electronics. A warning
to the driver will appear, too. The driver warning goes out after about
5 seconds, b ut it can be brought up at any time by pressing the
!SET I
button again.
Usually, you can still drive to the next dealership. T urn off all but the
most necessary e lectr ica l consumers, s ince these dra in the vehicle's
battery.
0 Note
If the the _ i,_ warning symbo l (coo lant system malfunction) a lso
lights up on the instrument panel during the trip::::>
page 29, then
•
you have to stop immediately and turn off the engine . The coolant
pump is not work ing anymore- -danger of damage to the engine! •
Brake system malfunction
A malfunction in the brake system must be repaired as
soon as possible .
If the warning/indicator light BRAKE (USA models)/ ((D)
(Canada models) in the instrument cluster flashes, there is a
brake system malfunction. A driver message appears as well
to explain the malfunction in more detail. The driver warning
goes out after about 5 seconds, but it can be brought up at
any time by pressing the
[SET ] button again.
Stop the Vehicle and Check the Brake Fluid
-Stop the vehicle.
- Check the brake fluid level=>
page 290.
-Seek professional assistance if necessary .
Warning ! Fault in brake system. Contact
workshop
- Drive carefully to the nearest authorized Audi dealer or
other qualified workshop and have the malfunction
corrected =>,& .

Parking brake Please get to a repair shop
- If this symbol appears when the vehicle is stationary or
after the ignition is turned on, check to see if the parking brake can be released. Drive to an authorized Audi dealer
or other qualified workshop as soon as possible and have
the malfunction corrected. If the parking brake cannot be
opened, then take it to an expert at an authorized Audi
dealer.
- If the symbol appears while you are driving, it is possible
that the traction control or the emergency brake has
malfunctioned . It is possible that the parking brake
cannot be applied. It is also possible that the parking brake cannot be released after it has been applied. Drive
to an authorized Audi dealer or other qualified workshop
to have the malfunction corrected.
If the ABS system malfunctions, the ABS warning/indicator light illu­
minates together with the brake system malfunction warning/indi­
cator light=>&, .
& WARNING
• Always observe the warnings in=> page 2 72, "Engine compart­
ment", before opening the hood and checking the brake fluid.
• Driving with low brake fluid is a safety hazard. Stop the car and
get professional assistance.
• USA models: If the BRAKE warning light and the P warning
light come on together, the rear wheels could lock up first under
hard braking. Rear wheel lock-up can cause loss of vehicle control
and an accident. Have your vehicle repaired immediately by your
authorized Audi dealer or a qualified workshop. Drive slowly and
avoid sudden, hard brake applications.
• Canada models: If the brake warning light (Ci)) and the ABS
warning light come on together, the rear wheels could lock up
Controls and equip ­
ment Safety first
Driver information display
&, WARNING (continued)
first under hard braking. Rear wheel lock-up can cause loss of
vehicle control and an accident. Have your vehicle repaired imme­
diately by your authorized Audi dealer or a qualified workshop.
Drive slowly and avoid sudden, hard brake applications. •
Engine cooling system malfunction _t_
A malfunction in the engine cooling system must be
repaired as soon as possible .
If the -~- symbol flashes in the display, either the engine
coolant
temperature is too high or the engine coolant level is
too low. A driver message appears as well to explain the
malfunction in more detail. The driver warning goes out after
about 5 seconds , but it can be brought up at any time by
pressing the
(SET] button again.
Switch off engine and check coolant level
- Pull off the road.
- Stop the vehicle.
- Turn off the engine .
- Check coolant level==>
page 287.
-Add coolant if necessary==> page 288.
- Continue driving only after the engine coolant
warning/indicator light goes out .
- Contact your authorized Audi dealer for assistance if
necessary .
If t he engine coolant level is correct, then the radiator fan may be the
cause of the malfunction .
~
Vehicle care Technical data