display AUDI A5 CABRIOLET 2010 Owner's Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2010, Model line: A5 CABRIOLET, Model: AUDI A5 CABRIOLET 2010Pages: 364, PDF Size: 86.51 MB
Page 32 of 364

Driver information display
in. WARNING
• If your vehicle should break down for mechanical or other
rea son s, park at a safe di stan ce from movin g traffic , turn off the
e ngine and turn on th e hazard warning lights =>
page 66, "Emer
gency fl ashe rs A ".
• Never open th e hood if you see or hear steam or coo lant
es caping from the engine compartment -you ri sk being scalded.
Wait until you can no longer see or hear steam or coo lant
escaping.
• The engine compartment of any vehicle is a dangerous area .
Before you perform any work in the engine compartment, turn of
the engine and allow it to cool. Follow the warning stickers
=> page 2 72 , "Engine compartment" .
(D Note
Do not continue d riving if the _f_ symbol illuminates . There is a
ma lf u nction in the e ngine cooling system -you co uld damage you r
engine .•
Engine oil pressure malfunction "t::7:
The red engine oil pressure warning symbol r equires
imm ediat e service or repair . Driving with a low oil pres
sure indication is likely to cause severe engine damage.
If the ~ symbo l on the display flashes , th e eng ine o il pres
sure is too low . A driver message appea rs as well to exp lain
t h e malfunc tion in more detail. The driver warning goes ou t
a ft er a bout 5 seco nds, but it can be b roug ht up at a ny time by
p ressin g th e
(SET ] butto n again .
Switch off engine ! Oil pressure too low
-Sto p the veh icl e. - Tur
n the eng ine off.
- Chec k the engi ne oil level=>
page 284 .
-Contact your a uthor ized Audi dealer for assistance if
necessary .
Engine o il level too low
If the eng ine o il level is too low, add engine oil=> page 285 .
Engine oil level correct
If the symbo l~ flashes ev en though the eng ine oil leve l is cor rect,
please seek pro fessional assistance . Do not continue dr iv ing. Do not
leave t he e ngine runn ing
idle, either .
(I] Tips
• The engine oil pre ssure symbol ~ is not an indi cator for a low
engine oil level. Do not rely on it. Instead , check the oil level in your
engine at regular intervals, preferably each time you refuel, and
always before going on a long trip.
• The yellow oil level warning indication "" requires oil refill or
workshop service without delay. Do not wait until the red oil pre s
sure warning ~ starts to flash before you respond to the low oil
level warning ~ . By then, your engine may already h ave suffered
serious damage. •
Fill engine oil now~
~-Please repleni sh oil now
If the ~-symbo l ligh ts up, then t he oil has to be replen is hed right
now =>
page 285. •
Page 33 of 364

Steering malfunction@-
If there is a malfunction in the electronic steering column
lock, the steering cannot be unlocked.
If the ~- symbol in the display blinks, there is a malfunction
in the electronic steering column lock . A driver message
appears as well to explain the malf unction in more detail.
The driver warning goes out after about 5 seconds, b ut it can
be brought up at any time by pressing the
[ SET] button
again.
Stop the vehicle and turn off the engine. Steering
defecti ve
- Obtain professional assistance .
- Do
not tow you r vehicle .
& WARNING
Your vehicle must not be towed in t he e vent of a malfun ctio n in
the e lec tronic ste ering column lo ck because it cannot b e steered
due t o the lo cked steering.
If it is t owed with the stee ring locked ,
t her e is th e risk of an ac cident.
(I) Tips
The symbo l's appearance m igh t be d ifferen t in some mode ls. •
Ignition lock malfunction@-
A malfunction in the ignition lock must be repaired imme
diately.
If the ©- symbol in the display blinks, there is a malfunct ion
in the electronic ignition lock . A driver message appears as
well to explain the malfunct ion in more deta il. The dr iver
Controls and equip
ment Safety first
Dri
ver information display
warning goes out after about 5 seconds, but it can be
brought up at any time by pressing the
(S ET] button aga in
Defective ignition switch Get it serviced!
- Do not turn the engine off.
- Drive immed iately to an author ized serv ice facility to have
the malfunct ion corrected.
If the re is a ma lf u nction in the e lectronic ignition lock , the ignit ion
cannot be tur ned off . Drive immediately to an authorized service
facility to have the cause of the ma lfunct ion corrected.
On vehicles with convenience key*, t he eng ine shou ld not be sw itched
off using the start/stop button because the engine cannot be started
again after the ignition has been swi tched o ff.
[ i ] Tips
Th e symbo l's appea ra nce m ight be different in some models. •
Yellow symbols
Ayellow symbol means WARNING.
-0)
9 a:
ill
Fig. 22 Displ ay:
Yello w warni ng
s ymb ol
Yellow symbols ind icate a prior ity 2 malfunction -Warning!
Vehicle care Technical data
Page 34 of 364

Driver information display
When a yellow warning symbol appears, one warning tone sounds. A
dr iver message appears as well to explain the ma lfunction in more
detail. The driver warning goes out after about 5 seconds, but it can
be brought up at any time by pressing the !SET] button again.
Check the function displayed as soon as possible. The yellow symbol
will not go out again until the reason for the malfunction has been
corrected.
If several priority 2 malfunctions are present, the symbols appear in
succession and remain for about 2 seconds .
Dynamic steer ing*
=:>page 32
'O' I I , Worn brake pads =:>page33
Battery vo ltage => page34
Defective light bulb* =>page34
Check engine oil level => page 35 or
=>page 35
Engine oil sensor malfunction =:>page35
--
Low fuel leve l =>page34
Windshield washer fluid =>page34
level low
Convenience key*
=>page 33
Key not in vehicle
Light/rain sensor defective
=:>page33
--
Dynamic headlight range => page 35
control defective
[{] Tips
Battery in remote control key
Electromechanical
parking brake
Engine speed limitation*
adaptive light defective
Ignition lock malfunction
Adaptive dampers*
Windshield wiper defective
T ire pressure monitoring sys
tem*
Loss of tire pressure
Tire pressure monitoring sys
tem* System not available
=>page 38
-
=> page 112
-
=>page 35
=> page 35
=> page 35
=>page 35
=>page 36
-
=> page 315
=> page 315
The speed warnings warning threshold 1 and warning threshold 2
are also yellow symbols in some models. The warning is a lways
shown as a small symbol in the uppe r area of the display
=>page 25. •
Appli es to vehicles : wit h Au di dr iv e se lec t
Dynamic steering r
Dynamic steering: System malfunction
Page 35 of 364

This driver message and the symbol,;;:;,. appear when a system
malfunction occurs during travel. You can continue to drive carefully
at a reduced speed to a qualified workshop. Steering can be more
difficult or sensitive than usual. The steering whee l can also be at an
angle when driving straight .
Dynamic steering: initialization
If this driver message appears and the indicator lightl, is flash ing on
the instrument panel, dynamic steering is being reinitialized . Once
you start the engine after this is finished, the steering wheel wi ll be
easy to move. Re -initializat ion might be necessary if the steering
wheel was moved hard to the left and right while the vehicle was not
moving. The display goes out as soon as initial izat io n is complete.
& WARNING
Have the dynamic steering system malfunction repaired as soon
as possible by an authorized Audi dealer or any qualified workshop
- risk of accident!
[I) Tips
The dynamic steer ing stability systems are not ava ilab le in the event
of a system ma lfunct ion .•
Ap plies to ve hicles : w it h c onven ien ce key
Key not in vehicle
Key not in vehicle
This reminder appears along with the symbol if the master key is
removed from the vehicle with the engine running. It is int ended to
remind you (e.g. when chang ing drivers) not to continue the journey
without the master key.
If the master key is no longer in the veh icle, you cannot sw itch off the
ignition after stopping the engine and you a lso cannot start the
engine again. You also cannot lock the veh icle from the outs ide .•
Controls and equip
ment Safety first
Driver information display
Light/rain sensor defective
·)
Automatic headlights/automatic wipers defective
If the symbol ill um inates , the light sensor has failed. For safety
reasons the low beams are turned o n permanently with the switch in
AUTO . However, you can continue to turn the lights on and off using
the light switch . In the case of a defect in the ra in sensor, the wind
shield wiper lever functions are still avai lable . Have the light/rain
sensor checked as soon as possib le by an autho rized Audi dealer. •
Worn brake pads ~
Brake pads!
If the warning light illuminates, immediately contact your authorized
Audi dealer or qualified workshop to have all brake pads inspected .
On USA mode ls the warning light comes on together with the
war ning light BRAKE . Both sets of b rake pads on an axle must always
be replaced at the same time.
& WARNING
Driving with bad brakes can cause a collision and serious personal
injury .
• If the warning light and the warning light
BRAKE1> with the
message Brake pads! comes on in the instrument cluster display,
immediately contact your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if necessary. •
ll BRAKE : USA mode ls on ly
Vehicle care Technical data
Page 36 of 364

Driver information display
Applies to veh icles : w ith defective lig ht bulb warning
Defective light bulb warning
The defective light bulb warning monitors the function of
the light bulbs in the vehicle.
T he defect ive light bulb war ning moni tors t he f unct io n of the light
bulbs. If a defective light b ulb is detected, or if a light bu lb has
burned o ut, a ye llow sym bol appe ars as we ll as a not ifica tion th at
shows which light bulb is defective .
Defective bulb~
If this symbol I") lights up, a t urn signa l (front or rear), a head lamp, a
bra ke light, t he b ack-up light, a fog l amp o r a rear fog lamp h as
fa iled.
& WARNING
• Light bulbs are unde r pre ssure and can explode when bulbs are
replaced - risk of injury.
• With gas-discharge lamp s* (xenon headlights ), the high
voltage component must be handled appropriately . Doing other
wise poses a risk of death!
[I] Tips
Have an aut horized Audi dealer or other q ualified workshop perform
t he rep lacement or the rep air .•
Windshield washer fluid level too low o
- Plea se refill washer fluid
If the symbo l illum inates, add w indshield washer f lu id to the washer
system and a lso to the headlight w asher system =>
page 295. •
Fuel supply too low )
When the symbol illum inates, this means t here are about 2.1
ga llons (8 l ite rs) of f ue l left in the f uel t ank. T ime to re fuel!
=>page 275.
If the symbol lights up, even when there is ample fue l in the tank, an d
the text
TANK SYSTEM MALFUNCTION! CONTACT WORKSHOP
appea rs in the disp lay, there is a fa ult in the system. Contact a quali
fied wo rkshop to have t he fa ult rectified. •
Applies to veh icles: with ba ttery voltage warn ing
Battery voltage 0
If battery powe r d rops into the range where it can lim it the ability of
the engine to start, t his the symbol ~ appears in the i nstr ument
cl uste r d isp lay with the following driver message
battery charge low:
Indicates charging by being driven .
While this driver not ification is displayed, you have to be prepa red for
limited sta rting ca pability.
Driver message appears and goes out again
If th is drive r mess age appears a fter the igni tion i s tur ned o n or whil e
dr iving and it goes o ut agai n after a while, the battery has been
a de qua tely rech arged.
Driver message appears and does not go out again
If th is dr iver no tifi cati on appears after the ign it ion is tu rned on o r
w hil e driving and does not go out again, the battery 's state of charge
is not in th e o ptim al r ange. Startin g cap abili ty is rest ric ted. H ave t he
battery c hecked at an a uth orized A udi dea ler or othe r qua lified work
shop as soon as possible. •
Page 37 of 364

Check engine oil 1o
Please top off with ma x. ll of o il. You can keep dri ving.
If the ~ symbo l lights up displaying t his drive r message, t hen ad d a
maximum of
1 liter at your earliest opportunity~ page 285. •
Engine oil level i!:r..,
Please check oil level
When the symbol i lluminates, check the engine oi l level as soo n as
poss ible ~
page 284. Top off the oil at your earliest o pportunity
~ page 285. •
Engine oil sensor defective
" Oil level! Sensor defective
If the symbo l illumina tes, contact your author ized A udi dealer and
have the o il sensor inspected. Until you have this done, check the oil
level each tim e yo u refue l ju st to be on the s afe side ~
page 28 4. •
A pplies t o veh icl es: with eng ine s peed lim itat io n
Engine speed limitation 71
Do not e xceed ma x. engine speed of XXXX rpm
Th e ~ symbo l ill uminates whe n there is an engi ne con trol malfunc
t ion . The ind icator light
Er"" in the instr ument cluster also i llum inates .
Th e engine speed is limited to the s peed disp laye d in the driver info r
mation system . Keep in m ind that the engine speed will not exceed
the value disp layed in the driver information system, for examp le
w hen downshifti ng.
Please go to a n author ized Audi dealer or other qualified workshop to
h ave the mal func tion rep aired .•
Controls and equip
ment Safety first
Driver information display
• Headlight range control defective
)
Headlight range control defective !
If the sym bo l ~ ill um ina tes, the dynam ic he adl ight range con tro l is
no lo nger work ing properly . H ave t he system checked and repa ired at
your authorize d Aud i dea ler. •
App lies to ve hicle s: wit h ad apti ve light
Adaptive light defective f:.J
adaptive light defective
When this symbol Ji.., ill uminates, it means that adaptive light is
defective. Go to an author ized Audi dealer to h ave the headlig hts o r
the contro l unit for the adaptive lig ht repa ire d.•
Ignition lock malfunction ..c,
~ Ignit ion lock defective
If the sym bol i n the displ ay comes on, t here is a mal func tion in t he
elect ronic ignit ion lock . Please go to an authorized Audi dealer or
o th er qu alified w orkshop to have the mal func tio n re pa ir ed .•
A pp lies to ve hicl es: w it h Aud i d ri ve sele ct
Adaptive dampers~
Adaptive dampers: system malfunction
If the symbol in the dis pl ay comes on , there is a malfunction in the
adaptive dampers . P lease go to an au thorized Aud i dea le r or other
qualifie d wo rks hop to have t he malfunct io n repaire d.•
Vehicle care Technical data
Page 38 of 364

Driver information display
Windshield wipers faulty ::>
->Windscreen wiper defecti ve !
W hen th is symbol "' illum ina tes, i t means th at the e lectro nics for
the windsh ield w ipers are defect ive . Please go to an authorized Audi
dealer or q ualified wor kshop to have the winds hield wiper system
repaired .•
Page 40 of 364

Opening and closing
(I) Tips
• The operation of the remote control key can be temporarily
disrupted by interference from transmitters in the vicinity of the
vehicle working in the same frequency range (e.g . a cell phone, radio
equipment).
• If you open the driver's door with the key left in the ignition lock,
a chime will sound. This is your reminder to remove the key and lock
the door .
• For security reasons, replacement keys are only available from
Audi dealers.
• For Declaration of Compliance to United States FCC and Industry
Canada regulations=>
page 346 . •
Check Light in the master key
The check light in the master key provides information
about different conditions.
Fig. 24 Check light in
t he master key
The check light comes on briefly once when a button is pressed, and
during an "inquiry" by the convenience key system. If the check
light does not come on, the battery is dead and has to be
replaced. In addition, when the battery is dead the symbo l appears
in the instrument cluster display as well as the message :
Please change key battery
Battery replacement => page 38. •
Master key battery replacement
•
Fig. 25 Remote
master key: Removing
the mechanical key
Fig. 26 Remote
master key: Removing
the battery holder
We recommend having the battery changed by an authorized
Audi dealer. However, if you wish to replace the dead battery
yourself, proceed as follows:
- Press the release button©~ fig. 25 . ..,.
Page 49 of 364

& WARNING (continued)
compartment and pull the lid shut, becoming trapped and unable
to get out. To reduce the risk of personal injury, never let children
play in or around your vehicle. Always keep the rear lid as well as
the vehicle doors closed when not in use.
• Always ensure that no one is within range of the rear lid when
it is moving, in particular close to the hinges· fingers or hands can
be pinched.
[ i ] Tips
• When the vehicle is locked, the rear lid can be opened separately
by pressing the button~ on the master key. When you close the rear
lid again, it locks automatically .
• If the rear l id is open or not properly closed when the ignition is
turned on, the door and rear lid warning:::::,
page 20 appears in the
instrument cluster display.•
Emergency unlocking of the
luggage compartment lid
There is an emergency release for the rear lid.
Con tro ls a nd e quip
m en t
Fig. 38 Rear lid: Lock
cylinder
Vehicle OP-eration
Opening and closing
-Remove the mechanical key from the master key
=;,page 39.
-Insert the key in the lock cylinder and turn it in the direc
tion of the arrow .•
Power windows
Controls
The driver can control all power windows.
Fig. 39 Section of the
driver's door: Controls
Fig. 40 Center
console: central power
window switch
All power window switches=> fig . 39 are provided with a two-
position function:
~
Vehicle care Do-it-yourselt service iTechnical data
Page 53 of 364

• A message in the instrument cluster display will alert you if a
protection function was activated or if there is a malfunction
~page 51.
• The power top can also be operated manuall y if there is a malfunc
tion~
page 56, "Power top emergency operation". Have you autho
r iz ed A udi dealer correct the cause of the malfunction as soon as
possible.
• If park ing the vehicle with the power top open, remember that the
vehicle interior will not be protected from the weather or from unau
thorized entry. Closing the power top before leaving the vehicle is
recommended. If you leave items in the vehicle, lock them in the
trunk. •
_ Power top operation
The indicator light monitors the power top.
The 4' indicator light illuminates for approximately 2 seconds when
the ignition switches on to check the function and then goes out
again . The indicator light also:
• illuminates when the powe r top opens or closes.
• blinks if the power top switch is operated but the conditions for
opening or clos ing the powe r top are not met . A wa rning message
also appears in the instrument cluster display~
page 51, "Error
message in the instrument cluster display ".
• if the power top did not open or close completely.
[ i ] Tips
The ind icator light stays on if the power top was opened manually. •
Controls and equip
ment Safety first
Power top
Error message in the instrument cluster
display
An error message appears if the power top cannot open
or close.
Several conditions must be met for the power top to open or close
automatically.
An error message in the instrument cluster display indicates if one of the conditions is not met or there is a malfunction.
Power top: please close rear lid
The luggage compartment l id must be closed when the power top is
opening or clos ing. This error message appears in the instrument
cluster display if the luggage compartment lid is not closed.
Storage bay not lowered. Please remove
obstruction
The power top storage bay must lower when the power top is
opening. Th is error message appears in the instrument cluster
display if the storage bay is not lowered.
If the storage bay does not
lower automatically because of objects in the lug gage compartment,
remove the objects that are in the way from the storage bay area.
Otherwise, you can operate the power top storage bay manually
~page 54.
Power top: cannot be used
This error message appears if the convertib le cannot open or close
automatically because of safety reasons or if there is a malfunction.
The follow ing causes are poss ible:
• Vehicle speed too high: Power top operat ion is deactivated and an
error message appears if the vehicle speed is too high . Reduce the
vehicle speed and operate the switch again to open or close the power
top.
• Battery voltage too low: The power top cannot be operated if the
battery voltage is too low . This ensures there w ill be enough battery .,,
Vehicle care Technical data