reset CADILLAC DEVILLE 1996 7.G Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 1996, Model line: DEVILLE, Model: CADILLAC DEVILLE 1996 7.GPages: 354, PDF Size: 20.32 MB
Page 30 of 354
Downloaded from www.Manualslib.com manuals search engine P
tl
3. Just before it reaches the end, give it a quick pull.
4. Let the belt go back all the way.
You should hear a
slight clicking sound.
If you don’t, the adjustment
feature won’t set, and
you’ll have to start again.
’‘A
.... ..
5. Now you can add a small amount of slack. Lean
forward slightly, then sit back.
If you’ve added more
than
1 inch (25 mm) of slack, pull the shoulder belt
out as you did before and start again.
If you move around in the vehicle enough, or if you pull
out the shoulder belt, the belt will become tight again.
If
this happens, you can reset it.
1-15
Page 67 of 354
Downloaded from www.Manualslib.com manuals search engine Power Door Locks
Press the power door lock to lock or unlock all the
doors at once. The
rear power door locks only provide a
lock function as a safety feature. They will not unlock
the doors.
Automatic Door Locks
Close your doors and turn on the ignition. Every time
you move the shift lever out of PARK (P) all of the
doors will lock. The doors will unlock every time you stop the vehicle and move the shift lever into
PARK (P).
If someone needs to get out while your vehicle is not in
PARK
(P), have that person use the manual or power
lock. When the
door is closed again, it will not lock
automatically. Use the manual
or power lock to lock the
door again.
Programmable Automatic Door Locks
With the ignition in the RUN position, the.door locks
can be programmed through the Driver Information
Center
(DIC) to allow the driver to choose various lock
settings. Press the RESET button to answer “yes”
and press the INFORMATION button to indicate
a
“no” response.
c
2-4
Page 68 of 354
Downloaded from www.Manualslib.com manuals search engine c-
c-
c
To begin programming, press the INFORMATION and
RESET buttons at the same time. The first prompt to
appear is
AUTOMATIC DOOR LOCK?. You must
press the
RESET button when this prompt appears to
continue programming the doors. The next prompt
to
appear is ENABLE ALL DOORS FOR LOCK AND
UNLOCK?. This selection locks all doors when shifting
out of
PARK (P) and unlocks all doors when shifting
back into
PARK (P). DISABLE ALL.DOORS FOR
LOCK AND UNLOCK? is used when you do not want
any automatic lock functions. The
ENABLE ALL
LOCKS AND DRIVER
DOOR UNLOCK? prompt
locks all doors when shifting out
of PARK (P) and
unlocks
only the driver’s door when shifting back into
PARK (P). ENABLE ALL DOORS FOR LOCK
ONLY? selection appears next. This prompt is used to
lock all
doors when shifting out of PARK (P) and keeps
the doors locked when you shift back into
PARK (P).
A yes or no response must be programmed when a
prompt is displayed.
A yes response selects the prompt
and a no response displays the
next prompt.
c
When you finish programming the door locks, the next
prompt to appear is for the vehicle storage mode. For
more information on vehicle storage, see “Battery Guard
Storage” later in this section.
Rear Door Security Locks
Your Cadillac is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors
of your
vehicle from the inside.
To use this lock:
1. .Move the lever on the door all the way up to the
2. Close the door.
ENGAGED position.
3. Do the same thing
to the other rear door lock.
The rear doors of your vehicle cannot be opened from
the inside when this feature is in use.
When
you want to open a rear door when the security
lock is on:
1. Unlock the door from the inside.
2. Then open the door from the outside.
2-5
Page 70 of 354
Downloaded from www.Manualslib.com manuals search engine f
r
r
r
r
i
r
Should interference to this system occur, try this:
a
0
a
a
Check to determine if battery replacement is
necessary.
See the instructions on battery
replacement.
Check
the distance. You may be too far from your
vehicle. This product has a maximum range. Check the location. Other vehicles
or objects may be
blocking the signal.
See your Cadillac dealer or
a qualified technician
for service.
Changes
or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
Operation
* When you press this symbol to unlock the
driver’s door, the parking lamps on your vehicle will
blink twice. Pressing it again within
five seconds will
unlock the other doors. Pressing this button will also
disarm the optional theft-deterrent system and turn
on the interior lamps at night.
8 When you press this symbol to lock the doors,
the parking lamps
will blink once. This also arms the
optional theft-deterrent system.
Press this symbol to open the
trunk.
@ Press this button to open the fuel door.
The Keyless Entry transmitter can
also be used to recall
the memory seats for up to
two drivers. For more
information see, “Memory Seat”
in the Index.
Note that pressing the transmitter buttons numerous
times (approximately
500 times) out of the vehicle’s
operating range may cause the transmitter not
to work.
Replacing the battery and pressing the transmitter
buttons
10 or more times out of range will also cause
the transmitter not to work.
To reset the transmitter,
you must
be within the.vehicle’s operating range. Press
and hold the
trunk button and within one second
press the lock button. Continue to hold both buttons
for approximately three seconds. See your Cadillac
dealer for service
if your transmitter still doesn’t
work properly.
2-7
Page 98 of 354
Downloaded from www.Manualslib.com manuals search engine P
P
c
Windshield Washer
A CAUTION:
In freezing weather, don’t use your washer until
the windshield
is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
NOTICE:
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
Don’t mix water with ready-to-use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system.
Also,
water doesn’t clean as well as washer fluid.
NOTICE: (Continued)
NOTICE: (Continued)
Fill your washer fluid tank only 314 full
when
it’s very cold. This allows for
expansion, which could damage the tank
if
it is completely full.
windshield washer. It can damage your
washer system and paint.
Don’t use radiator antifreeze in your
Press and hold the
PUSH paddle to wash the windshield.
Release the paddle when you have enough fluid. The
wipers will
clear the windshield and either stop or return
to your preset speed.
LOW WASHER FLUID will be displayed on the DIC
when the washer fluid reaches a low level.
Driving without washer fluid can be dangerous.
A bad
mud splash
can block your vision and you could hit
another
vehicle or go off the road. Check the washer
fluid level often.
2-35 c
Page 101 of 354
Downloaded from www.Manualslib.com manuals search engine Resuming a Set Speed
Setting the cruise control at
a desired speed and then
applying the brake
will end
the cruise function. Once
you’re going about
25 mph
(40 km/h) or more, you can
move the cruise control
I switch from ON to R/A
(Resume/Accelerate) for
about half a second to reset.
This returns you
to your
desired preset speed.
I
Remember, if you hold the switch at R/A longer than
half a second, the vehicle will accelerate until you
release the switch or apply the brake.
You could be
startled and even lose control.
So unless you want to
go faster, don’t hold the switch at RJA.
Increasing Speed While Using Cruise Control
There are two ways to increase your speed. Here’s
the first:
1. Use the accelerator pedal to go to a higher speed.
2. Push the button at the end of the lever and then
release the button
and the accelerator pedal. You’ll
now cruise at the higher speed.
Here’s
the second way to increase speed:
0 Move the cruise switch from ON to R/A. Hold it
there until you reach
a desired speed and then release
the switch.
0 To increase your speed in very small amounts, move
the switch to R/A. Each time you
do this, your
vehicle will
go about 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you’have set the
cruise control speed by pushing the SET CRUISE button.
0
0
2-38
Page 108 of 354
Downloaded from www.Manualslib.com manuals search engine c
c
c
c
c
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle’s battery
against drainage from the interior lamps,
trunk lamp,
glove box lamp, cigarette lighters or the garage door opener. When the ignition is turned
OFF, the power to
these features will automatically
turn off after 10 minutes
(three minutes if a new car has
15 miles or less). Power
will
be restored for an additional 10 minutes if any door
is opened, the
trunk is opened or the courtesy lamp
switch is turned on.
Battery Guard Storage
This feature is for long term use and miust be
programmed through the DIC while the ignition is in the
RUN position. Battery guard storage protects the battery
by placing the vehicle in a storage mode
so that the
radio, amplifiers, instrument cluster and Remote Keyless
Entry
(RKE) will not drain the battery over a long
period
of time.
To begin programming, press the INFORMATION
and RESET buttons at
the same time for approximately
two seconds. Press the RESET button to answer
“yes” and press the INFORMATION button to indicate a “no” response. The first prompt
to appear relates to the automatic door
locks. This feature can be bypassed by pressing the
INFORMATION button. The STORAGE MODE?
prompt appears next. To select, press the
RESET button.
ENABLE STORAGE MODE? will then appear. A yes
or no response must be given. If the INFORMATION
(no) button is pressed, the DISABLE STORAGE
MODE? prompt will appear. Once again, a yes or no
response is required.
Once the battery guard has been programmed, your
vehicle will enter the storage mode approximately
20 minutes after the ignition key has been turned off.
The RKE will also be disabled at this point. The RKE
will reactivate when a door or the trunk is opened,
however,
if your vehicle is left inactive for another
20 minutes the RKE will re-enter the storage mode.
Your vehicle will stay in the storage mode until the
ignition key
is turned out of LOCK. The system will
“wake-up” when the
door key is inserted into the door
however, your vehicle will remain in the storage mode.
The ignition must be out of
LOCK before the battery
guard is disabled.
2-45
Page 130 of 354
Downloaded from www.Manualslib.com manuals search engine r
f
r:
r
f
Anti-Lock Brake System Warning Light
ANTI -
LOCK -.
With the anti-lock brake system, this light will come
on when you start your
engine and may stay on
for several seconds.
That’s normal.
lkaction Control System Warning Light
This warning light should
come on briefly
as you start
the engine. If the waming
light doesn’t come on then,
have it fixed
so it will be
ready to warn you if there’s
a problem.
If the light stays on, turn the ignition off.
Or, if the light
comes on when you’re driving, stop as soon as possible
and
turn the ignition off. Then start $e engine again to
reset the system. If the light still stays on, or. comes
on
again while you’re driving, your Cadillac needs service.
If the regular brake system warning light isn’t on, you
still have brakes, but you don’t have anti-lock brakes.
If the regular brake system warning light is also on, you
don’t have anti-lock brakes and there’s a problem with
your regular brakes. See “Brake System Warning Light”
earlier
in this part.
The anti-lock brake system warning light should come
on briefly when you
turn the ignition key to RUN. If the
light doesn’t come on then, have
it fixed so it will be
ready to
warn you if there is a problem. If
it stays on, or comes on when you’re driving, there
may
be a problem with your traction control system and
your vehicle may need service. When this warning light
is on, the system will not
limit wheel spin. Adjust your
driving accordingly.
2-67
Page 137 of 354
Downloaded from www.Manualslib.com manuals search engine When AVG MPG is selected, the total distance is
divided by the total fuel used.
When the INST button (Instantaneous Fuel Economy)
is
selected, you will see what the fuel economy is at that
instant. The computer takes a new reading twice every second. It will show economy up to
70 miles-per-gallon
(or
2 L per 100 km).
To reset the average fuel economy, press the
INFORMATION button until the AVG MPG is
displayed on the
DIC. Press and hold the RESET
button until both the fuel data center and DIC display
reads
0.0.
The RANGE display shows how far the computer thinks
you can travel with the fuel that is in the tank. The
computer does not
know what driving conditions will be
like for the rest of your trip, so the range is estimated
based on the recent fuel economy. Therefore, the range
reading may change as your driving habits change.
Going from city to highway driving may increase the
range reading.
If the range display shows
LO, you should stop for fuel
as
soon as possible. Your computer needs enough data
for the
RANGE reading to work.
Driver Information Center (DIC)
The DIC display gives you the status of many of your
vehicle's systems. The
DIC is used to display driver
selectable information and warning/status messages.
If more than one problem is detected, the
DIC will
automatically display all current messages.
Digital Control Buttons
i
I
c
2-74
Page 138 of 354
Downloaded from www.Manualslib.com manuals search engine c
c-
rc
Ir
.-
c
DISPLAY ONIOFF: Pressing this button will turn off
the DIC, Electronic Climate Control, fuel data center, the fuel gage, trip odometer and odometer. While the
displays
are off, pressing the INFORMATION button
will only turn on the DIC. If the TRIP SET button
is pressed or the fuel level falls below four gallons
(15.2 L), all the displays will come back on.
ENG/MET (EnglishMetric): You can change the
display from English (miles) to metric (kilometers) by
pressing this button. The same button also changes other
readings (like temperature, fuel and odometer).
TRIP SET By using this button you can tell how far
you’ve gone since you last set the TRIP SET back to
zero.
To reset, press and hold the button until zeros
appear. If your vehicle
is domestic, the trip odometer
will return to zero after 999.9 miles
(1 609 km). If your
vehicle
is Canadian, the trip odometer will return to zero
after
1 999.9 km (1,242 miles).
INFORMATION: Pressing this button repeatedly will
display the AVG
MPG, FUEL USED, AVG MPH, OIL
LIFE LEFT, ENGINE RPM, BATTERY VOLTS and
COOLANT TEMP.
TIMER: This feature is like a stopwatch, in that you
can clock the time it takes to get from one point
to another.
To operate, press the TIMER button until TIMER
0O:OO:OO is displayed on the DIC. Each of the fields for
the hours, minutes and seconds are
two numeric digits.
Once TIMER
OFF 0O:OO:OO is displayed, press the
TIMER button to start the timing feature. Press the
TIMER button again to stop
it, If you will be starting
and stopping
your Cadillac, during a trip for instance,
the TIMER feature will automatically
start timing where
it left off when you last stopped. To reset it, press and
hold the RESET button until the display reads TIMER
0O:OO:OO. Press the INFORMATION button to exit from
the TIMER function.
RESET Pressing this button will reset the MPG AVG,
FUEL USED, AVG MPH and OIL LIFE LEFT. Pressing
RESET when a non-resettable display appears will
cause
a “recall” mode to occur. When this happens, all
DIC warning messages that have been displayed since
the ignition key was turned to RUN will redisplay.
If no
messages were displayed, a MONITORED SYSTEMS
OK message will appear.
2-75