sensor CHRYSLER VOYAGER 2000 Diagnostic Manual

TEST ACTION APPLICABILITY
8 The following are possible causes for O2 Sensor Slow Response: exhaust leak, fuel
contamination, O2 sensor failure, electrical wiring connectors, electrical mechanical,
and O2 heater failure.
Turn Ignition On (Engine Off).
Using a voltmeter, backprobe O2S (Sensor Ground) Circuit between O2S Connector
(Sensor Ground) and PCM Connector (Sensor Ground).
Is the voltage drop reading below 0.10 VDC?All
Ye s®Replace the O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Repair poor connection (high resistance) on O2 Sensor Ground
Circuit.
Perform VERIFICATION TEST VER-5A3.
70
DRIVEABILITY
P-0139 1/2 O2S SLOW RESPONSE ÐContinued
ProCarManuals.com

Symptom:
P-0140 1/2 O2 SENSOR STAYS AT CENTER
When Monitored and Set Condition:
P-0140 1/2 O2 SENSOR STAYS AT CENTER
When Monitored: With the engine running for more than 2 minutes and engine
temperature greater than 76 degrees C (170 degrees F).
Set Condition: The Upstream Oxygen Sensor Signal voltage is between 0.35 volt and 0.55
volt for 1.5 minutes.
POSSIBLE CAUSES
O2 SENSOR 1/2 GROUND CIRCUIT OPEN
O2 SENSOR 1/2 SIGNAL CIRCUIT OPEN
1/2 O2 SENSOR WIRING HARN INTER DEFECT
1/2 O2 SENSOR WIRING HARN OBS DEFECT
O2 SENSOR 1/2 DEFECTIVE
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition Off
Start the engine and allow it to reach normal operating temperature.
With the DRB in actuator tests, set RPM to 1500.
In sensors, read the Downstream Oxygen Sensor Level.
Is the Downstream O2 Sensor Level switching?All
Ye s®Go To 2
No®Go To 4
2 Ignition Off
Start the engine and allow it to reach normal operating temperature.
Using the DRB, set the engine speed to 1500 RPM.
With the DRB, read the Downstream O2 Sensor state.
Wiggle Downstream O2 Sensor Connector and Harness.
While wiggling the Harness, monitor the DRB display.
At any time was the Downstream O2 Sensor state locked at center?All
Ye s®Repair the open Harness or Connector that caused the O2 Sensor
state to stay at center.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
71
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
No®Test Complete.
4 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using an Ohmmeter, measure the resistance between the Downstream O2 Sensor
Ground Circuit and a good engine ground.
Is the resistance above 5.0 ohms?All
Ye s®Repair the open Downstream O2 sensor Ground Circuit.
Perform Powertrain Verification Test VER-5A.
No®Go To 5
5 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Downstream O2 Sensor Signal Circuit and B(+).
Ignition on, engine not running.
Using the DRB in sensors, read the Downstream Oxygen Sensor voltage.
Is the voltage above 1.0 volt?All
Ye s®Replace the Downstream O2 Sensor.
Perform Powertrain Verification Test VER-5A.
No®Go To 6
6 Ignition Off
Disconnect the Downstream O2 Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Disconnect the PCM Connector.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the Downstream O2 Sensor Signal
Circuit from the O2 Sensor Connector to the PCM Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 7
No®Repair the open Downstream O2 Sensor Signal Circuit.
Perform Powertrain Verification Test VER-5A.
7 If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-5A.
72
DRIVEABILITY
P-0140 1/2 O2 SENSOR STAYS AT CENTER ÐContinued
ProCarManuals.com

Symptom:
P-0141 1/2 O2S HEATER FAILURE
When Monitored and Set Condition:
P-0141 1/2 O2S HEATER FAILURE
When Monitored: With the ignition key off, after the engine cools down.
Set Condition: No sensor output signal is received when the PCM powers up the sensor
heater.
POSSIBLE CAUSES
1/2 O2 SENSOR CONNECTOR DAMAGED
1/2 O2 SENSOR GND CIRCUIT OPEN
ASD RELAY OUTPUT CIRCUIT OPEN
1/2 O2 SENSOR FAILURE
1/2 O2 SENSOR HEATER ELEMENT FAILURE
1/2 O2S HEATER FAILURE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the GLOBAL GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 Turn Ignition On (Engine Off), wait three minutes.
With the DRB, monitor the O2 Sensor voltage for a few minutes until the voltage
stabilizes between .4 and .6 volts.
With the DRB, actuate the O2 Heater test.
Monitor O2 voltage for up to two minutes.
Is the O2 Sensor voltage still between .4 and .6 volts?All
Ye s®Go To 3
No®Go To 4
3 At this time the 1/2 O2S HEATER FAILURE does not exist or is an intermittent
problem.
With the DRB, read the FREEZE FRAME DATA.
With this screen, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the 1/2 O2S HEATER FAILURE reoccur?All
Ye s®Go To 4
No®1/2 O2S Heater failure no longer exists.
Perform VERIFICATION TEST VER-5A3.
73
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Is any terminal corroded, damaged, pushed out or miswired?All
Ye s®Repair or replace as necessary.
Perform VERIFICATION TEST VER-5A3.
No®Go To 5
5 Turn Ignition On (Engine Off).
Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
With the DRB, actuate the ASD Relay.
Using a voltmeter, measure the ASD Relay Output Circuit at the O2 Sensor
Connector (harness side).
Is the voltage above 10.0 volts?All
Ye s®Go To 6
No®Repair the open ASD Relay Output Circuit.
Perform VERIFICATION TEST VER-5A3.
6 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure the O2 Sensor Heater Element at the O2 Sensor
Connector (component side).
Is the resistance between 4 and 7 ohms?All
Ye s®Go To 7
No®Replace the 1/2 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
7 Disconnect the 1/2 O2 Sensor Connector.
Check connectors - Clean / repair as necessary.
Using an ohmmeter, measure from the Heater Ground Circuit to ground at the O2
Sensor Connector (harness side).
Is the resistance below 5.0 ohms?All
Ye s®Replace the 1/2 O2 Sensor.
Perform VERIFICATION TEST VER-5A3.
No®Repair the open 1/2 O2 Sensor Ground Circuit.
Perform VERIFICATION TEST VER-5A3.
74
DRIVEABILITY
P-0141 1/2 O2S HEATER FAILURE ÐContinued
ProCarManuals.com

Symptom:
P-0171±1/1 FUEL SYSTEM LEAN
When Monitored and Set Condition:
P-0171±1/1 FUEL SYSTEM LEAN
When Monitored: With the engine running in closed loop mode, the ambient, battery
temperature above Ð5 deg. C (20 deg. F) and altitude below 8000 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.
POSSIBLE CAUSES
FUEL PUMP MODULE DEFECTIVE
TPS VOLTAGE CHANGE NOT SMOOTH
TPS VOLTAGE <0.92V
FUEL INLET STRAINER PLUGGED
ECT SENSOR DEFECTIVE (OUT OF CALIBRATION)
MAP SENSOR DEFECTIVE (OUT OF CALIBRATION)
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (HIGH)
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (LOW)
FUEL PUMP CAPACITY (VOLUME) OUT OF SPECS
TEST ACTION APPLICABILITY
1 Turn ignition on.
With the DRB, read the DTC's.
Is the Global Good Trip Counter displayed and equal to zero for P0171?All
Ye s®Go To 2
No®Go To 13
2 Ignition On, Engine Not Running
With the DRB, read the TPS voltage.
While monitoring the DRB, slowly open and close the Throttle.
Is the voltage change smooth?All
Ye s®Go To 3
No®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
75
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition On, Engine Not Running.
With the DRB, read TPS Sensor voltage. Throttle must be against stop.
Is the voltage 0.92 or less with the Throttle closed?All
Ye s®Go To 4
No®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
4 Turn ignition On.
With the DRB in sensors, read the ªEngine Coolant Tmp Degº value.
Note: If engine coolant temperature is above 82ÉC (180ÉF), allow the engine
to cool until 62ÉC (150ÉF) is reached.
Start the Engine.
While monitoring the DRB, allow the engine to reach normal operating temperature
above 82ÉC (180ÉF).
Did the engine coolant temperature value reach 82ÉC (180ÉF) or above?All
Ye s®Go To 5
No®Replace the Engine Coolant Temperature Sensor.
Perform Powertrain Verification Test VER-5A.
5 Turn ignition On.
With the DRB in sensors, read the88Eng Coolant Tmp Deg'' value
Note: If engine coolant temperature is above 82ÉC (180ÉF), allow the engine
to cool until 62ÉC (150ÉF) is reached.
Start the Engine.
While monitoring the DRB, allow the engine to reach normal operating temperature
above 82ÉC (180ÉF).
Was the coolant temperature value increase a smooth transition?All
Ye s®Go To 6
No®Replace the Engine Coolant Temperature Sensor.
Perform Verificatino Test VER-5A.
6 Turn ignition off.
Connect a Vacuum Gauge to a Manifold Vacuum source.
Start the engine.
Allow the engine to idle.
Note: If engine will not idle, maintain a constant RPM above idle.
Using the DRB in Sensors, read the MAP Sensor vacuum value.
Is the DRB reading within 19of the Vacuum Gauge reading?All
Ye s®Go To 7
No®Replace the MAP Sensor.
Perform Powertrain Verification Test VER-5A.
76
DRIVEABILITY
P-0171±1/1 FUEL SYSTEM LEAN ÐContinued
ProCarManuals.com

Symptom
P0172 -1/1 FUEL SYSTEM RICH
When Monitored and Set Condition:
P0172 -1/1 FUEL SYSTEM RICH
When Monitored: With the engine in closed loop mode, the ambient/battery temperature
above þ5 deg. C (20 deg. F) and altitude below 8000 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
the result is below a certain value for two trips, a freeze frame is stored, the MIL
illuminates and a trouble code is stored.
POSSIBLE CAUSES
FUEL PUMP MODULE DEFECTIVE
TPS VOLTAGE CHANGE NOT SMOOTH
TPS VOLTAGE <0.92V
FUEL INLET STRAINER PLUGGED
ECT SENSOR DEFECTIVE (OUT OF CALIBRATION)
MAP SENSOR DEFECTIVE (OUT OF CALIBRATION)
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (HIGH)
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (LOW)
TEST ACTION APPLICABILITY
1 Turn ignition on.
With the DRB, read the DTC's.
Is the DTC Specific Good Trip Counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 14
2 Ignition On, Engine Not Running
With the DRB, read the TPS voltage.
While monitoring the DRB, slowly open and close the Throttle.
Is the voltage change smooth?All
Ye s®Go To 3
No®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
79
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition On, Engine Not Running.
With the DRB, read TP Sensor voltage. Throttle must be against stop.
Is the voltage 0.92 or less with the Throttle closed?All
Ye s®Go To 4
No®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
4 Turn ignition on.
With the DRB in sensors, read the ªEng Coolant Tmp Degº value.
Note: If engine coolant temperature is above 82ÉC (180ÉF), allow the engine
to cool until 62ÉC (150ÉF) is reached.
Start the Engine.
While monitoring the DRB, allow the engine to reach normal operating temperature
above 82ÉC (180ÉF).
Did the engine coolant temperature value reach 180ÉF or above?All
Ye s®Go To 5
No®Replace the Engine Coolant Temperature Sensor.
Perform Powertrain Verification Test VER-5A.
5 Turn ignition On.
With the DRB in sensors, read the ªEng Coolant Tmp Deg'' value
Note: If engine coolant temperature is above 82ÉC (180ÉF), allow the engine
to cool until 62ÉC (150ÉF) is reached.
Start the Engine.
While monitoring the DRB, allow the engine to reach normal operating temperature
above 82ÉC (180ÉF).
Was the coolant temperature value increase a smooth transition?All
Ye s®Go To 6
No®Replace the Engine Coolant Temperature Sensor.
Perform Verification Test VER-5A.
6 Turn ignition off.
Connect a Vacuum Gauge to a Manifold Vacuum source.
Start the engine.
Allow the engine to idle.
Note: If engine will not idle, maintain a constant RPM above idle.
Using the DRB in Sensors, read the MAP Sensor vacuum value.
Is the DRB reading within 19of the Vacuum Gauge reading?All
Ye s®Go To 7
No®Replace the MAP Sensor.
Perform Powertrain Verification Test VER-5A.
7Note: Engine must be at operating temp and in closed loop to perform this
test.
Start engine and run until operating temp and closed loop mode is reached.
With the DRB under System Tests, go to ªPurge Vapors Test''. Observe the Short
Term Adaptive value and press 3 to flow.
Note: Short Term Adaptive should change.
Did the Short Term Adaptive value change?All
Ye s®Go To 8
No®Refer to symptom *CHECKING EVAPORATIVE EMISSION
SYSTEM in the DRIVEABILITY category.
80
P0172 -1/1 FUEL SYSTEM RICH ÐContinued
ProCarManuals.com

Symptom List:
P-0300 MULTIPLE CYLINDER MIS-FIRE
P-0301 CYLINDER #1 MIS-FIRE
P-0302 CYLINDER #2 MIS-FIRE
P-0303 CYLINDER #3 MIS-FIRE
P-0304 CYLINDER #4 MIS-FIRE
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-0300 MULTIPLE CYLINDER
MIS-FIRE.
When Monitored and Set Condition:
P-0300 MULTIPLE CYLINDER MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0301 CYLINDER #1 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0302 CYLINDER #2 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0303 CYLINDER #3 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0304 CYLINDER #4 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
100
DRIVEABILITY
ProCarManuals.com