display CITROEN C-ELYSÉE 2016 Owner's Guide

87
C-elysee_en_Chap05_conduite_ed01-2016
Cruise control
System which automatically maintains the speed   of   the   vehicle   at   the   value   programmed  
b

y   the   driver,   without   any   action   on   the  
a

ccelerator
 ped
al.
The cruise control is switched on
 
m
anually:
 it r

equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h),   as   well   as   the   engagement   of:
-
 
f
ourth   gear   on   a   manual   gearbox,
-
 
s
econd   gear   on   a   or   automatic   or   electronic  
g

earbox,   in   sequential   mode,
-
 
p
osition   A   on   an   electronic   gearbox   or  
p

osition D   on   an   automatic   gearbox.
The cruise control is switched off
 
m
anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value. The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A.
1.
 C

ruise   control   mode   selection   thumb  
w

heel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 C

ruise   control   off/resume   button.Steering mounted controls
The cruise control cannot, in any
circumstances,  replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  programmed   information   is   grouped  
t

ogether   in   the   instrument   panel   screen.
5.
  C
ruise   control   off/resume   indication.
6.
  C
ruise   control   mode   selection   indication.
7.
  P
rogrammed   speed   value.
Displays in the instrument
panel
5
Driving

88
C-elysee_en_Chap05_conduite_ed01-2016
F Turn  thumb   wheel   1 to the
"CRUISE"  position:
  the   cruise   control  
m

ode   is   selected   but   is   not   switched   on  
(

PAUS E).
Programming
You can then change the programmed speed using buttons 2 and 3:
-  b y   +   or   -   1   mph   (km/h)   =   short   press,
-
 
b
y   +   or   -   5   mph   (km/h)   =   long   press,
-
 
i
n   steps   of   +   or   -   5   mph   (km/h)   =   maintained   press. When
  the   cruise   control   is   switched   on,  
b

e   careful   if   you   maintain   the   pressure  
o

n   one   of   the   programmed   speed  
c

hanging   buttons:   this   may   result   in   a  
v

ery   rapid   change   in   the   speed   of   your  
v

ehicle.
Do not use the cruise control on
slippery
  roads   or   in   heavy   traffic.
On
  a   steep   descent,   the   cruise   control  
w

ill not be able to prevent the vehicle
from
  exceeding   the   programmed   speed.
To
  avoid   any   risk   of   jamming   of   the  
ped

als:
-
 
e
nsure   that   the   mat   is   secured  
c

o r r e c t l y,
-
 
n
ever   fit   one   mat   on   top   of   another.
In
  the   event   of   a   cruise   control   malfunction,  
t

he   speed   is   cleared   resulting   in   flashing   of   the  d
ashes.   Have   it   checked   by   a   CITROËN   dealer  o
r   a   qualified   workshop.
Operating fault
Leaving cruise control mode
F Turn   thumb   wheel   1 to the "0"  position:   the   cruise   control   mode   is  d
eselected.   The   display   returns   to   the   distance   recorder.
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results   in   flashing   of   this   speed   in   the   screen.
Return
  to   the   programmed   speed,   by   means   of   intentional   or  
u

nintentional   deceleration   of   the   vehicle,   automatically   cancels   the  
f

lashing   of   the   speed.F
 
S
et   the   programmed   speed   by  
a

ccelerating   to   the   required   speed,  
t

hen press button 2 or 3   (e.g.:   70   mph  
(

110   km/h)).
F  
S
witch   off   the   cruise   control   by   pressing   button   4
:   the   screen  
c

onfirms   that   it   has   been   switched   off   (PAUSE).
F  
S
witch   the   cruise   control   back   on   by   pressing   button   4  
ag
ain.
Driving

89
C-elysee_en_Chap05_conduite_ed01-2016
This system indicates the proximity of an obstacle   (person,   vehicle,   tree,   gate,   etc.)  
w

hich   comes   within   the   field   of   detection   of  
s

ensors   located   in   the   bumper.
Certain
  types   of   obstacle   (stake,   roadworks  
c

one,   etc.)   detected   initially   will   no   longer   be  
d

etected   at   the   end   of   the   manoeuvre   due   to  
t

he   presence   of   blind   spots.
Rear parking sensors
This function cannot, in any
circumstances,  take   the   place   of   the   need f

or   vigilance   on   the   part   of   the   driver.The
  system   is   switched   on   by   engaging   reverse  
g

ear.   This   is   accompanied   by   an   audible   signal.
The   system   is   switched   off   when   you   come   out  
o

f   reverse   gear.
Audible assistance
The proximity information is given by an i
ntermittent   audible   signal,   the   frequency   of   which i

ncreases   as   the   vehicle   approaches   the   obstacle.
The
  sound   emitted   by   the   speaker   (right   or   left)
 i

ndicates   the   side   on   which   the   obstacle   is   located.
When
  the   distance   between   the   vehicle   and
 t

he   obstacle   becomes   less   than   approximately
 t

hirty   centimetres,   the   audible   signal   becomes
 c

ontinuous.
Visual assistance
This supplements the audible signal by d isplaying   bars   in   the   screen   which   move  
p

rogressively   nearer   to   the   vehicle.
When
  the   obstacle   is   very   close,   the   "Danger"  
s

ymbol   is   displayed   in   the   screen.
5
Driving

90
C-elysee_en_Chap05_conduite_ed01-2016
In bad weather or in winter, ensure that   the   sensors   are   not   covered   with  
m

ud,   ice   or   snow.   When   reverse   gear   is  
e

ngaged,   an   audible   signal   (long   beep)  
i

ndicates   that   the   sensors   may   be   dirty.
Certain
  sound   sources   (motorcycle,  
l

orry,   pneumatic   drill,   etc.)   may   trigger  
t

he   audible   signals   of   the   parking  
s

ensor   system.
In
  the   event   of   a   malfunction   of  
t

he   system,   when   reverse   gear  
i

s   engaged   this   warning   lamp  
i

s
 
displayed   in   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,   accompanied  
b

y
 
an
 
audible   signal   (short   beep).
Contact   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Operating fault
The function will be deactivated a
utomatically   if   a   trailer   is   being   towed  
o

r   a   bicycle   carrier   is   fitted   (vehicle  
f

itted   with   a   towbar   or   bicycle   carrier  
r

ecommended   by   CITROËN).
Deactivation / Activation of the
rear parking sensors
The function is deactivated or activated  v ia  t he  v ehicle  c onfiguration  
m

enu.
The
  status   of   the   function   is   stored  
w

hen   the   ignition   is   switched   off.
For
 
more
 
information   on   access   to   the   parking  
s

ensors
 
menu,   refer   to   the   "Personalisation   -  
C

onfiguration"   part   of   the   "Monitoring"   section.
Driving

92
C-elysee_en_Chap06_visibilite_ed01-2016
Selection ring for main lighting
mode
Turn the ring to align the desired symbol with the ma rking.
Lighting
  off   (ignition   off)   /   Daytime  
r

unning   lamps   (engine   running).
Sidelamps
 o

nly.
Dipped
  or   main   beam   headlamps.
Dipping the headlamps
Pull the stalk to switch the lighting between dipped   /   main   beam   headlamps.
In
  the   lighting   off   and   sidelamps   modes,   the  
d

river   can   switch   on   the   main   beam   headlamps  
t

emporarily   ("headlamp   flash")   by   maintaining   a  
p

ull   on   the   stalk.
Display
Illumination of the corresponding indicator lamp in   the   instrument   panel   confirms   the   lighting  
s

witched   on.
Visibility

102
C-elysee_en_Chap07_securite_ed01-2016
Before reinitialising the system, ensure that the pressures of the four tyres are
correct
  for   the   use   of   the   vehicle   and   in  
l

ine   with   the   recommendations   on   the  
t

yre   pressure   label.
The
  under-inflation   alert   can   only   be  
r

elied   on   if   the   reinitialisation   of   the  
s

ystem   has   done   with   the   pressures   in  
t

he   four   tyres   correctly   adjusted.
The
  under-inflation   detection   system  
d

oes   not   give   a   warning   if   a   pressure   is  
i

ncorrect   at   the   time   of   reinitialisation.
The
 
loss
 
of
 
pressure
 
detected
 
does
 
not
 
a

lways
 
cause
 
visible
 
bulging
 
of
 
the
 
tyre.
 
D

o
 
not
 
satisfy
 
yourself
 
with
 
just
 
a
 
visual
 
c

heck. The
 
alert
 
is
 
maintained
 
until
 
the
 
system
 
i

s
 r

einitialised.
Under-inflation alert
This is given by fixed illumination of t his   warning   lamp,   accompanied   by  
a

n   audible   signal   and   the   display   of   a  
m

essage.
F
 
R

educe   speed   immediately,   avoid  
e

xcessive   steering   movements   and   sudden  
b

raking
F

S

top the vehicle as soon as it is safe to
do so. F
 I f   you   have   a   compressor   (such   as   the   one  
i

n   the   temporary   puncture   repair   kit),   check  
t

he   pressures   of   the   four   tyres   when   cold.  
I

f   it   is   not   possible   to   carry   out   this   check  
s

traight   away,   drive   carefully   at   reduced  
s

peed.
or
F

I
n the event of a puncture, use the
temporary
  puncture   repair   kit   or   the   spare  
w

heel   (depending   on   equipment),
Reinitialisation
It is necessary to reinitialise the system every time   one   or   more   tyre   pressures   are   adjusted,  
a

nd   after   changing   one   or   more   wheels.
Safety

103
C-elysee_en_Chap07_securite_ed01-2016
Reinitialisation of the system must be done with the ignition on and   the   vehicle stationary:
-  i n   the   vehicle   configuration   menu   for   vehicles   fitted   with   a   display   screen,
-
 
u
sing   the   button   in   the   glove   box   for   vehicles   without   display   screen.
Monochrome screen C
F Press the "7" or " 8" button to select the
" Driving assistance ",
  category,   then  
c

onfirm   by   pressing   the   central   button.
F

P
ress the " 7" or " 8", button to select " Ty r e
pressures" , then "Reinitialisation ", then
confirming
  by   pressing   the   central   button.
 A

  message   confirms   the   reinitialisation.
F
P
ress the MENU
button for access to the
main
 
menu.
F

P

ress the " 7" or " 8" button to select the
" Personalisation-configuration ",
 
menu
 
t

hen
 

confirm
 

by
 

pressing
 

the
 

central
 

button.
F

P

ress the " 7" or " 8" button to select the
" Define vehicle parameters ",
 
menu,
 
then
 
c

onfirm
 
by
 
pressing
 
the
 
central
 
button.
7
Safety

104
C-elysee_en_Chap07_securite_ed01-2016
Vehicles without display screen
F Open  the   glove   box.
F  M ake   a   long   press   on   this   button.
Reinitialisation
  is   confirmed   by   an   low-pitched  
a

udible
 s
ignal.
A
  high-pitched   audible   signal   indicates   that   the  
r

einitialisation   has   not   been   done.
The
  new   pressure   settings   registered   are  
c

onsidered   to   be   reference   values   by   the  
s

ystem.
Operating fault
The under-inflation alert is only d ependable   if   the   system   has   been  
r

einitialised   with   all   four   tyres   inflated   to  
t

he   correct   pressures.
Snow chains
The system does not have to be reinitialised   after   fitting   or   removing  
sn

ow
 c
hains. Before
  doing   anything   to   the   system,  
t

he   pressures   of   the   four   tyres   must   be  
c

hecked   and   the   system   reinitialised.
The
  flashing   and   then   fixed   illumination   of   the  
u

nder-inflation
 w
arning
 lam
p
 a
ccompanied
 b

y   illumination   of   the   Service   warning   lamp  
i

ndicates   a   fault   with   the   system.
In   this   case,   under-inflation   monitoring   of   the  t
yres   is   no   longer   assured.
Have   the   system   checked   by   a   CITROËN  
d

ealer   or   a   qualified   workshop.
S

106
C-elysee_en_Chap07_securite_ed01-2016
Anti-slip regulation (ASR)
and electronic stability
programme (ESP)
The anti-slip regulation (also known as Traction Control)   optimises   traction   to   prevent   skidding o

f   the   wheels,   by   acting   on   the   brakes   of   the
 d

riving   wheels   and   on   the   engine.
The
  electronic   stability   programme   acts   on   the
 b

rake   of   one   or   more   wheels   and   on   the   engine
 t

o   keep   the   vehicle   on   the   trajectory   required   by
 t

he   driver,   within   the   limits   of   the   laws   of   physics.
This
  is   indicated   by   flashing   of   this  
w

arning   lamp   in   the   instrument   panel. The
  ASR /ESP   systems   offer  
e

xceptional   safety   in   normal   driving,   but  
t

his   should   not   encourage   the   driver   to  
t

ake   extra   risks   or   drive   at   high   speed.
The
  correct   functioning   of   these  
s

ystems   depends   on   observation   of  
t

he
 ma
nufacturer's
 r
ecommendations
 r

egarding   the   wheels   (tyres   and   rims),  
t

he   braking   components,   the   electronic  
c

omponents   and   the   assembly  
a

nd   repair   procedures   used   by   the  
C

ITROËN   dealer   network.
After
  an   impact,   have   these   systems  
c

hecked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
Illumination of the warning lamp, accompanid   by   a   message   in   the  
s

creen   indicates   a   malfunction   of  
t

hese   systems.
Reactivation
These systems are reactivated automatically every   time   the   ignition   is   switched   of,   or   from  
3

0   mph   (50   km/h).
F
 
P
ress   this   button   again   to   reactivate   them  
m

anually.
 T

he   lamp   in   the   button   goes   off.
The
  symbol   going   off   in   the   instrument   panel  
i

ndicates   the   reactivation   of   the   ASR   and  
ES

P systems.
Deactivation
In exceptional conditions (starting a vehicle which   is   bogged   down,   stuck   in   snow,   on   soft  
g

round,   ...),   it   may   be   advisable   to   deactivate  
t

he   ASR   and   ESP   systems,   so   that   the   wheels  
c

an   move   freely   and   regain   grip.
Trajectory control systems
Activation
These systems are activated automatically each   time   the   vehicle   is   started.
They
  come   into   operation   in   the   event   of   a   grip  
o

r
 t
rajectory
 pro
blem. The
  display   of   this   symbol   indicates  
t

hat   the   ASR   and   ESP   systems   are  
d

eactivated.
F
 
P
ress   this   button   button,   located   on  
t

he   dashboard   (driver's   side),   until   the  
c

orresponding   symbol   appears   in   the  i
nstrument   panel   screen. T
he   lamp   in   the   button   comes   on.Contact
  a   CITROËN   dealer   or   a   qualified  
w

orkshop   to   have   the   ASR /ESP   systems  
c

hecked.
Coasting   with   the   engine   off   results   in   a
 l

oss   of   power   assistance   for   the   steering.
S

134
C-elysee_en_Chap09_info-pratiques_ed01-2016
Range indicators
Once the AdBlue® tank is on reserve or after d
etection
 
of
 
a
 
fault   with   the   SCR   emissions  
c

ontrol
 
system,
 
when   the   ignition   is   switched  
o

n,
 
an
 
indicator
 
displays   an   estimate   of   the  
d

istance
 
that
 
can
 
be   covered,   the   range,   before  
e

ngine
 
starting
 
is
 
prevented.
In
 
the
 
event
 
of
 
simultaneous   system   fault   and  
l

ow
 
AdBlue
® level, the shortest range figure is t
he
 
one
 
displayed.
In the event of the risk of non-starting related to a lack of AdBlue®
Range greater than 1 500 miles (2 400 km)
When   the   ignition   is   switched   on,   no  
i

nformation   on   range   is   displayed   automatically  
i

n   the   instrument   panel.
Remaining range between 350 and 1500 miles (600 and 2 400 km)
When switching on the ignition, the UREA warning   lamp   comes   on,   accompanied   by   an  
a

udible   signal   and   the   temporary   display   in  
t

he   instrument   panel   of   "NO   START   IN"   and  
a

  distance,   indicating   the   remaining   range  
e

xpressed   in   miles   or   kilometres   before  
e

ngine   starting   is   prevented   -   (For   example  
"

NO START   IN   900   miles"   means   that   "Starting  
w

ill   be   prevented   in   900   miles).
When
  driving,   this   display   appears   every  
1

50 miles   (300   km)   until   the   additive   tank   has  
be

en
 t
opped-up.
Go
  to   a   dealer   CITROËN   or   a   qualified  
w

orkshop   to   have   the   AdBlue
® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
For
 
more
 
information
 
on
 
topping-up   the  
Ad

Blue
® additive, refer to the corresponding s
ection.
The
 
engine
 
start
 
prevention
 
system
 
r

equired
 
by
 
regulations
 
is
 
activated
 
a

utomatically
 
once
 
the
 
AdBlue
® tank is e
m pt y.
Practical information