DAEWOO MATIZ 2003 Service Repair Manual

ENGINE CONTROLS 1F–3
DAEWOO M-150 BL2
DTC P1628 Immobilizer No Successful
Communication 1F-270. . . . . . . . . . . . . . . . . . . . . . .
DTC P1629 Immovilizer Wrong Computation 1F-272
DTC P0656 Fuel Level Gauge Circuit Fault 1F-274.
DTC P1660 Malfunction Indicator Lamp (MIL)
High Voltage 1F-276. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P1661 Malfunction Indicator Lamp (MIL)
Low Voltage 1F-278. . . . . . . . . . . . . . . . . . . . . . . . . .
Symptom Diagnosis 1F-280. . . . . . . . . . . . . . . . . . . . . .
Important Preliminary Checks 1F-280. . . . . . . . . . . . .
Intermittent 1F-281. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard Start 1F-283. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surges or Chuggles 1F-286. . . . . . . . . . . . . . . . . . . . .
Lack of Power, Sluggishness or Sponginess 1F-288
Detonation/Spark Knock 1F-290. . . . . . . . . . . . . . . . . .
Hesitation, Sag, Stumble 1F-292. . . . . . . . . . . . . . . . .
Cuts Out, Misses 1F-294. . . . . . . . . . . . . . . . . . . . . . . .
Poor Fuel Economy 1F-296. . . . . . . . . . . . . . . . . . . . . .
Rough, Unstable, or Incorrect Idle, Stalling 1F-297. .
Excessive Exhaust Emissions or Odors 1F-300. . . .
Dieseling, Run-on 1F-302. . . . . . . . . . . . . . . . . . . . . . .
Backfire 1F-303. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance and Repair 1F-304. . . . . . . . . . . . . . . . . .
On-Vehicle Service 1F–304 . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump 1F–304 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 1F-305. . . . . . . . . . . . . . . . .
Fuel Filter 1F-306. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Tank 1F-307. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Rail and Injectors 1F-308. . . . . . . . . . . . . . . . . . .
Evaporator Emission Canister 1F-309. . . . . . . . . . . . . Evaporator Emission Canister Purge
Solenoid 1F-310. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold Absolute Pressure (MAP) Sensor 1F-310. .
Throttle Body 1F-311. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature (ECT) Sensor 1F-312.
Intake Air Temperature (ECT) Sensor 1F-313. . . . . .
Oxygen Sensor (O2S 1) 1F-314. . . . . . . . . . . . . . . . . .
Heated Oxygen Sensor (HO2S 2) 1F-314. . . . . . . . .
Electric Exhaust Gas Recirculation (EEGR)
Valve 1F-315. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knock Sensor 1F-315. . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Ignition (EI) System Ignition Coil 1F-316.
Crankshaft Position (CKP) Sensor 1F-316. . . . . . . .
Camshaft Position (CMP) Sensor 1F-317. . . . . . . . . .
Engine Control Module (ECM) 1F-317. . . . . . . . . . . . .
Specifications 1F-319. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specification 1F-319. . . . . . . . . .
Special Tools 1F-319. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1F-319. . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 1F-320. . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 1 of 5) 1F-320. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 2 of 5) 1F-321. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 3 of 5) 1F-322. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 4 of 5) 1F-323. . . . . . . . . . . . . . . . . . . .
ECM Wiring Diagram
(Sirius D3 – 5 of 5) 1F-324. . . . . . . . . . . . . . . . . . . .

1F–4 ENGINE CONTROLS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
IGNITION SYSTEM OPERATION
This ignition system does not use a conventional distrib-
utor and coil. It uses a crankshaft position sensor input
to the Engine Control Module (ECM). The ECM then de-
termines Electronic Spark Timing (EST) and triggers the
electronic ignition system ignition coil.
This type of distributorless ignition system uses a “waste
spark’’ method of spark distribution. Each cylinder is in-
dividural with coil per cylinder.
These systems use the EST signal from the ECM to
control the EST. The ECM uses the following informa-
tion:

Engine load (manifold pressure or vacuum).

Atmospheric (barometric) pressure.

Engine temperature.

Intake air temperature.

Crankshaft position.

Engine speed (rpm).
ELECTRONIC IGNITION SYSTEM
IGNITION COIL
The Electronic Ignition (EI) system ignition coil is
mounted near on the cylinder head.
A terminals of the EI system ignition coil provides the
spark for each spark plug. The EI system ignition coil is
not serviceable and must be replaced as an assembly.
CRANKSHAFT POSITION SENSOR
This Electronic Ignition (EI) system uses a magnetic
crankshaft position sensor. This sensor protrudes
through its mount to within approximately 1.3 mm (0.05
inch) of the crankshaft reluctor. The reluctor is a special
wheel attached to the crankshaft with 58 slots machined
into it, 57 of which are equally spaced in 6-degree inter-
vals. The last slot is wider and serves to generate a
“sync pulse.” As the crankshaft rotates, the slots in the
reluctor change the magnetic field of the sensor, creat-
ing an induced voltage pulse. The longer pulse of the
58th slot identifies a specific orientation of the crank-
shaft and allows the Engine Control Module (ECM) to
determine the crankshaft orientation at all times. The
ECM uses this information to generate timed ignition
and injection pulses that it sends to the ignition coils and
to the fuel injectors.
CAMSHAFT POSITION SENSOR
The Camshaft Position (CMP) sensor sends a CMP sig-
nal to the Engine Control Module (ECM). The ECM uses
this signal as a “sync pulse” to trigger the injectors in the
proper sequence. The ECM uses the CMP signal to indi-
cate the position of the #1 piston during its power stroke.
This allows the ECM to calculate true sequential fuel in-jection mode of operation. If the ECM detects an incor-
rect CMP signal while the engine is running, Diagnostic
Trouble Code (DTC) P0341 will set. If the CMP signal is
lost while the engine is running, the fuel injection system
will shift to a calculated sequential fuel injection mode
based on the last fuel injection pulse, and the engine will
continue to run. As long as the fault is present, the en-
gine can be restarted. It will run in the calculated se-
quential mode with a 1-in-6 chance of the injector
sequence being correct.
IDLE AIR SYSTEM OPERATION
The idle air system operation is controlled by the base
idle setting of the throttle body and the Idle Air Control
(IAC) valve.
The Engine Control Module (ECM) uses the IAC valve to
set the idle speed dependent on conditions. The ECM
uses information from various inputs, such as coolant
temperature, manifold vacuum, etc., for the effective
control of the idle speed.
FUEL CONTROL SYSTEM
OPERATION
The function of the fuel metering system is to deliver the
correct amount of fuel to the engine under all operating
conditions. The fuel is delivered to the engine by the in-
dividual fuel injectors mounted into the intake manifold
near each cylinder.
The main fuel control sensors are the Manifold Absolute
Pressure (MAP) sensor, the oxygen sensor (O2S), and
the heated oxygen sensor (HO2S).
The MAP sensor measures or senses the intake man-
ifold vacuum. Under high fuel demands, the MAP sensor
reads a low vacuum condition, such as wide open
throttle. The Engine Control Module (ECM) uses this in-
formation to enrich the mixture, thus increasing the fuel
injector on-time, to provide the correct amount of fuel.
When decelerating, the vacuum increases. This vacuum
change is sensed by the MAP sensor and read by the
ECM, which then decreases the fuel injector on-time
due to the low fuel demand conditions.
The O2S is located in the exhaust manifold. The HO2S
is located in the exhaust pipe. The oxygen sensors indi-
cate to the ECM the amount of oxygen in the exhaust
gas, and the ECM changes the air/fuel ratio to the en-
gine by controlling the fuel injectors. The best air/fuel ra-
tio to minimize exhaust emissions is 14.7:1, which
allows the catalytic converter to operate most efficiently.
Because of the constant measuring and adjusting of the
air/fuel ratio, the fuel injection system is called a “closed
loop” system.
The ECM uses voltage inputs from several sensors to
determine how much fuel to provide to the engine. The

ENGINE CONTROLS 1F–5
DAEWOO M-150 BL2
fuel is delivered under one of several conditions, called
“modes.’’
Starting Mode
When the ignition is turned ON, the ECM turns the fuel
pump relay on for 2 seconds. The fuel pump then builds
fuel pressure. The ECM also checks the Engine Coolant
Temperature (ECT) sensor and the Throttle Position
(TP) sensor and determines the proper air/fuel ratio for
starting the engine. The ECM controls the amount of
fuel delivered in the starting mode by changing how long
the fuel injector is turned on and off. This is done by
“pulsing’’ the fuel injectors for very short times.
Run Mode
The run mode has two conditions called “open loop’’ and
“closed loop.’’
Open Loop
When the engine is first started and it is above 400 rpm,
the system goes into “open loop’’ operation. In “open
loop,’’ the ECM ignores the signal from the O2S and cal-
culates the air/fuel ratio based on inputs from the ECT
sensor and the MAP sensor. The ECM stays in ”open
loop” until the following conditions are met:

The O2S has a varying voltage output, showing that it
is hot enough to operate properly.

The ECT sensor is above a specified temperature.

A specific amount of time has elapsed after starting
the engine.
Closed Loop
The specific values for the above conditions vary with
different engines and are stored in the Electronically
Erasable Programmable Read-Only Memory (EE-
PROM). When these conditions are met, the system
goes into “closed loop” operation. In “closed loop,” the
ECM calculates the air/fuel ratio (fuel injector on-time)
based on the signals from the oxygen sensors. This al-
lows the air/fuel ratio to stay very close to 14.7 to 1.
Acceleration Mode
The ECM responds to rapid changes in throttle position
and airflow and provides extra fuel.
Deceleration Mode
The ECM responds to changes in throttle position and
airflow and reduces the amount of fuel. When decelera-
tion is very fast, the ECM can cut off fuel completely for
short periods of time.
Battery Voltage Correction Mode
When battery voltage is low, the ECM can compensate
for a weak spark delivered by the ignition module by us-
ing the following methods:

Increasing the fuel injector pulse width.

Increasing the idle speed rpm.

Increasing the ignition dwell time.
Fuel Cut-Off Mode
No fuel is delivered by the fuel injectors when the ignition
is off. This prevents dieseling or engine run-on. Also, the
fuel is not delivered if there are no reference pulses re-
ceived from the CKP sensor. This prevents flooding.
EVAPORATIVE EMISSION CONTROL
SYSTEM OPERATION
The basic Evaporative Emission (EVAP) control system
used is the charcoal canister storage method. This
method transfers fuel vapor from the fuel tank to an acti-
vated carbon (charcoal) storage canister which holds
the vapors when the vehicle is not operating. When the
engine is running, the fuel vapor is purged from the car-
bon element by intake airflow and consumed in the nor-
mal combustion process.
Gasoline vapors from the fuel tank flow into the tube la-
beled TANK. These vapors are absorbed into the car-
bon. The canister is purged by Engine Control Module
(ECM) when the engine has been running for a specified
amount of time. Air is drawn into the canister and mixed
with the vapor. This mixture is then drawn into the intake
manifold.
The ECM supplies a ground to energize the controlled
charcoal canister purge solenoid valve. This valve is
Pulse Width Modulated (PWM) or turned on and off sev-
eral times a second. The controlled charcoal canister
purge PWM duty cycle varies according to operating
conditions determined by mass airflow, fuel trim, and in-
take air temperature.
Poor idle, stalling, and poor driveability can be caused
by the following conditions:

An inoperative controlled canister purge valve.

A damaged canister.

Hoses that are split, cracked, or not connected to the
proper tubes.
CONTROLLED CHARCOAL
CANISTER
The controlled charcoal canister is an emission control
device containing activated charcoal granules. The con-
trolled charcoal canister is used to store fuel vapors from
the fuel tank. Once certain conditions are met, the En-
gine Control Module (ECM) activates the controlled
charcoal canister purge solenoid, allowing the fuel va-
pors to be drawn into the engine cylinders and burned.
POSITIVE CRANKCASE
VENTILATION CONTROL SYSTEM
OPERATION
A Positive Crankcase Ventilation (PCV) control system
is used to provide complete use of the crankcase va-

1F–6 ENGINE CONTROLS
DAEWOO M-150 BL2
pors. Fresh air from the air cleaner is supplied to the
crankcase. The fresh air is mixed with blowby gases
which then pass through a vacuum hose into the intake
manifold.
Periodically inspect the hoses and the clamps. Replace
any crankcase ventilation components as required.
A restricted or plugged PCV hose may cause the follow-
ing conditions:

Rough idle

Stalling or low idle speed

Oil leaks

Oil in the air cleaner

Sludge in the engine
A leaking PCV hose may cause the following conditions:

Rough idle

Stalling

High idle speed
ENGINE COOLANT TEMPERATURE
SENSOR
The Engine Coolant Temperature (ECT) sensor is a
thermistor (a resistor which changes value based on
temperature) mounted in the engine coolant stream.
Low coolant temperature produces a high resistance
(100,000 ohms at –40C [–40F]) while high tempera-
ture causes low resistance (70 ohms at 130C [266F]).
The Engine Control Module (ECM) supplies 5 volts to
the ECT sensor through a resistor in the ECM and mea-
sures the change in voltage. The voltage will be high
when the engine is cold and low when the engine is hot.
By measuring the change in voltage, the ECM can de-
termine the coolant temperature. The engine coolant
temperature affects most of the systems that the ECM
controls. A failure in the ECT sensor circuit should set a
Diagnostic Trouble Code (DTC) P0117 or P0118. Re-
member, these DTC indicate a failure in the ECT circuit,
so proper use of the chart will lead either to repairing a
wiring problem or to replacing the sensor to repair a
problem properly.
THROTTLE POSITION SENSOR
The Throttle Position (TP) sensor is a potentiometer
connected to the throttle shaft of the throttle body. The
TP sensor electrical circuit consists of a 5-volt supply
line and a ground line, both provided by the Engine Con-
trol Module (ECM). The ECM calculates the throttle
position by monitoring the voltage on this signal line. The
TP sensor output changes as the accelerator pedal is
moved, changing the throttle valve angle. At a closed
throttle position, the output of the TP sensor is low,
about 0.4–0.8 volt. As the throttle valve opens, the out-
put increases so that, at Wide Open Throttle (WOT), the
output voltage will be about 4.5–5 volts.The ECM can determine fuel delivery based on throttle
valve angle (driver demand). A broken or loose TP sen-
sor can cause intermittent bursts of fuel from the injector
and an unstable idle, because the ECM thinks the
throttle is moving. A problem in any of the TP sensor cir-
cuits should set a Diagnostic Trouble Code (DTC)
P0122 or P0123. Once the DTC is set, the ECM will sub-
stitute a default value for the TP sensor and some ve-
hicle performance will return.
CATALYST MONITOR OXYGEN
SENSORS
Three-way catalytic converters are used to control emis-
sions of hydrocarbons (HC), carbon monoxide (CO),
and oxides of nitrogen (NOx). The catalyst within the
converters promotes a chemical reaction. This reaction
oxidizes the HC and CO present in the exhaust gas and
converts them into harmless water vapor and carbon
dioxide. The catalyst also reduces NOx by converting it
to nitrogen. The ECM can monitor this process using the
oxygen sensor (O2S) and heated oxygen sensor
(HO2S). These sensors produce an output signal which
indicates the amount of oxygen present in the exhaust
gas entering and leaving the three-way converter. This
indicates the catalyst’s ability to efficiently convert ex-
haust gasses. If the catalyst is operating efficiently, the
O2S signals will be more active than the signals pro-
duced by the HO2S. The catalyst monitor sensors oper-
ate the same way as the fuel control sensors. The
sensors’ main function is catalyst monitoring, but they
also have a limited role in fuel control. If a sensor output
indicates a voltage either above or below the 450 mV
bias voltage for an extended period of time, the Engine
Control Module (ECM) will make a slight adjustment to
fuel trim to ensure that fuel delivery is correct for catalyst
monitoring.
A problem with the O2S circuit will set DTC P0131,
P0132, P0133 or P0134 depending on the special condi-
tion. A problem with the HO2S signal will set DTC
P0137, P0138, P0140 or P0141 depending on the spe-
cial condition.
A fault in the heated oxygen sensor (HO2S) heater ele-
ment or its ignition feed or ground will result in lower oxy-
gen sensor response. This may cause incorrect catalyst
monitor diagnostic results.
ELECTRIC EXHAUST GAS
RECIRCULATION VALVE
The Electric Exhaust Gas Recirculation (EEGR) system
is used on engines equipped with an automatic trans-
axle to lower oxides of nitrogen (NOx) emission levels
caused by high combustion temperature. The main ele-
ment of the system is the EEGR valve, controlled electri-
cally by the Engine Control Module (ECM). The EEGR
valve feeds small amounts of exhaust gas into the intake

ENGINE CONTROLS 1F–7
DAEWOO M-150 BL2
manifold to decrease combustion temperature. The
amount of exhaust gas recirculated is controlled by vari-
ations in vacuum and exhaust back pressure. If too
much exhaust gas enters, combustion will not take
place. For this reason, very little exhaust gas is allowed
to pass through the valve, especially at idle.
The EEGR valve is usually open under the following
conditions:

Warm engine operation.

Above idle speed.
Results of Incorrect Operation
Too much EEGR flow tends to weaken combustion,
causing the engine to run roughly or to stop. With too
much EEGR flow at idle, cruise, or cold operation, any of
the following conditions may occur:

The engine stops after a cold start.

The engine stops at idle after deceleration.

The vehicle surges during cruise.

Rough idle.
If the EEGR valve stays open all the time, the engine
may not idle. Too little or no EEGR flow allows combus-
tion temperatures to get too high during acceleration
and load conditions. This could cause the following con-
ditions:

Spark knock (detonation)

Engine overheating

Emission test failure
INTAKE AIR TEMPERATURE
SENSOR
The Intake Air Temperature (IAT) sensor is a thermistor,
a resistor which changes value based on the tempera-
ture of the air entering the engine. Low temperature pro-
duces a high resistance (100 kohms at –40C [–40F]),
while high temperature causes a low resistance (70
ohms at 130C [266F]).
The Engine Control Module (ECM) provides 5 volts to
the IAT sensor through a resistor in the ECM and mea-
sures the change in voltage to determine the IAT. The
voltage will be high when the manifold air is cold and low
when the air is hot. The ECM knows the intake IAT by
measuring the voltage.
The IAT sensor is also used to control spark timing when
the manifold air is cold.
A failure in the IAT sensor circuit sets a diagnostic
trouble code P0112 or P0113.
IDLE AIR CONTROL VALVE
Notice: Do not attempt to remove the protective cap
and readjust the stop screw. Misadjustment may result
in damage to the Idle Air Control (IAC) valve or to the
throttle body.The IAC valve is mounted on the throttle body where it
controls the engine idle speed under the command of
the Engine Control Module (ECM). The ECM sends volt-
age pulses to the IAC valve motor windings, causing the
IAC valve pintle to move in or out a given distance (a
step or count) for each pulse. The pintle movement con-
trols the airflow around the throttle valves which, in turn,
control the engine idle speed.
The desired idle speeds for all engine operating condi-
tions are programmed into the calibration of the ECM.
These programmed engine speeds are based on the
coolant temperature, the park/neutral position switch
status, the vehicle speed, the battery voltage, and the
A/C system pressure, if equipped.
The ECM “learns” the proper IAC valve positions to
achieve warm, stabilized idle speeds (rpm) desired for
the various conditions (park/neutral or drive, A/C on or
off, if equipped). This information is stored in ECM ”keep
alive” memories (information is retained after the ignition
is turned off). All other IAC valve positioning is calcu-
lated based on these memory values. As a result, en-
gine variations due to wear and variations in the
minimum throttle valve position (within limits) do not af-
fect engine idle speeds. This system provides correct
idle control under all conditions. This also means that
disconnecting power to the ECM can result in incorrect
idle control or the necessity to partially press the accel-
erator when starting until the ECM relearns idle control.
Engine idle speed is a function of total airflow into the
engine based on the IAC valve pintle position, the
throttle valve opening, and the calibrated vacuum loss
through accessories. The minimum throttle valve posi-
tion is set at the factory with a stop screw. This setting
allows enough airflow by the throttle valve to cause the
IAC valve pintle to be positioned a calibrated number of
steps (counts) from the seat during “controlled” idle op-
eration. The minimum throttle valve position setting on
this engine should not be considered the “minimum idle
speed,” as on other fuel injected engines. The throttle
stop screw is covered with a plug at the factory following
adjustment.
If the IAC valve is suspected as being the cause of im-
proper idle speed, refer to “Idle Air Control System
Check” in this section.
MANIFOLD ABSOLUTE PRESSURE
SENSOR
The Manifold Absolute Pressure (MAP) sensor mea-
sures the changes in the intake manifold pressure which
result from engine load and speed changes and con-
verts these to a voltage output.
A closed throttle on engine coast down produces a rela-
tively low MAP output. MAP is the opposite of vacuum.
When manifold pressure is high, vacuum is low. The
MAP sensor is also used to measure barometric pres-
sure. This is performed as part of MAP sensor calcula-

1F–8 ENGINE CONTROLS
DAEWOO M-150 BL2
tions. With the ignition ON and the engine not running,
the Engine Control Module (ECM) will read the manifold
pressure as barometric pressure and adjust the air/fuel
ratio accordingly. This compensation for altitude allows
the system to maintain driving performance while hold-
ing emissions low. The barometric function will update
periodically during steady driving or under a wide open
throttle condition. In the case of a fault in the barometric
portion of the MAP sensor, the ECM will set to the de-
fault value.
A failure in the MAP sensor circuit sets a diagnostic
trouble codes P0107, P0108 or P0106.
ENGINE CONTROL MODULE
The Engine Control Module (ECM), is the control center
of the fuel injection system. It constantly looks at the in-
formation from various sensors and controls the sys-
tems that affect the vehicle’s performance. The ECM
also performs the diagnostic functions of the system. It
can recognize operational problems, alert the driver
through the Malfunction Indicator Lamp (MIL), and store
diagnostic trouble code(s) which identify the problem
areas to aid the technician in making repairs.
There are no serviceable parts in the ECM. The calibra-
tions are stored in the ECM in the Programmable Read
Only Memory (PROM).
The ECM supplies either 5 or 12 volts to power the sen-
sors or switches. This is done through resistance in the
ECM which are so high in value that a test light will not
come on when connected to the circuit. In some cases,
even an ordinary shop voltmeter will not give an accu-
rate reading because its resistance is too low. You must
use a digital voltmeter with a 10 megohm input imped-
ance to get accurate voltage readings. The ECM con-
trols output circuits such as the fuel injectors, the Idle Air
Control (IAC) valve, the A/C clutch relay, etc., by control-
ling the ground circuit through transistors or a device
called a “quad-driver.”
FUEL INJECTOR
The Multi-port Fuel Injection (MFI) assembly is a sole-
noid-operated device controlled by the Engine Control
Module (ECM) that meters pressurized fuel to a single
engine cylinder. The ECM energizes the fuel injector or
solenoid to a normally closed ball or pintle valve. This al-
lows fuel to flow into the top of the injector, past the ball
or pintle valve, and through a recessed flow director
plate at the injector outlet.
The director plate has six machined holes that control
the fuel flow, generating a conical spray pattern of finely
atomized fuel at the injector tip. Fuel from the tip is di-
rected at the intake valve, causing it to become further
atomized and vaporized before entering the combustion
chamber. A fuel injector which is stuck partially open
would cause a loss of fuel pressure after the engine is
shut down. Also, an extended crank time would be no-
ticed on some engines. Dieseling could also occur be-cause some fuel could be delivered to the engine after
the ignition is turned off.
FUEL CUT-OFF SWITCH
The fuel cutoff switch is a safety device. In the event of a
collision or a sudden impact, it automatically cuts off the
fuel supply and activates the door lock relay. After the
switch has been activated, it must be reset in order to
restart the engine. Reset the fuel cutoff switch by press-
ing the rubber top of the switch. The switch is located
near the right side of the passenger’s seat.
KNOCK SENSOR
The knock sensor detects abnormal knocking in the en-
gine. The sensor is mounted in the engine block near the
cylinders. The sensor produces an AC output voltage
which increases with the severity of the knock. This sig-
nal is sent to the Engine Control Module (ECM). The
ECM then adjusts the ignition timing to reduce the spark
knock.
VARIABLE RELUCTANCE (VR)
SENSOR
The variable reluctance sensor is commonly refered to
as an “inductive” sensor.
The VR wheel speed sensor consists of a sensing unit
fixed to the left side front macpherson strut, for non-ABS
vehicle.
The ECM uses the rough road information to enable or
disable the misfire diagnostic. The misfire diagnostic
can be greatly affected by crankshaft speed variations
caused by driving on rough road surfaces. The VR sen-
sor generates rough road information by producing a
signal which is proportional to the movement of a small
metal bar inside the sensor.
If a fault occurs which causes the ECM to not receive
rough road information between 30 and 70 km/h (1.8
and 43.5 mph), Diagnostic Trouble Code (DTC) P1391
will set.
OCTANE NUMBER CONNECTOR
The octane number connector is a jumper harness that
signal to the engine control module (ECM) the octane
rating of the fuel.
The connector is located on the next to the ECM. There
are two different octane number connector settings
available. The vehicle is shipped from the factory with a
label attached to the jumper harness to indicate the oc-
tane rating setting of the ECM. The ECM will alter fuel
delivery and spark timing based on the octane number
setting. The following table shows which terminal to
jump on the octane number connector in order to
achieve the correct fuel octane rating. Terminal 2 is
ground on the octane number connector. The find the

ENGINE CONTROLS 1F–9
DAEWOO M-150 BL2
appropriate wiring diagram. Refer to “ECM Wiring Dia-
grams” in this Section.
9591
Terminal 49GroundOpen
STRATEGY-BASED DIAGNOSTICS
Strategy-Based Diagnostics
The strategy-based diagnostic is a uniform approach to
repair all Electrical/Electronic (E/E) systems. The diag-
nostic flow can always be used to resolve an E/E system
problem and is a starting point when repairs are neces-
sary. The following steps will instruct the technician on
how to proceed with a diagnosis:
Verify the customer complaint. To verify the customer
complaint, the technician should know the normal op-
eration of the system.

Perform preliminary checks as follows:

Conduct a thorough visual inspection.

Review the service history.

Detect unusual sounds or odors.

Gather Diagnostic Trouble Code (DTC) information to
achieve an effective repair.

Check bulletins and other service information. This
includes videos, newsletters, etc.

Refer to service information (manual) system
check(s).

Refer to service diagnostics.
No Trouble Found
This condition exists when the vehicle is found to oper-
ate normally. The condition described by the customer
may be normal. Verify the customer complaint against
another vehicle that is operating normally. The condition
may be intermittent. Verify the complaint under the con-
ditions described by the customer before releasing the
vehicle.
Re-examine the complaints.
When the complaints cannot be successfully found or
isolated, a re-evaluation is necessary. The complaint
should be re-verified and could be intermittent as de-
fined in “intermittents,” or could be normal.
After isolating the cause, the repairs should be made.
Validate for proper operation and verify that the symp-
tom has been corrected. This may involve road testing
or other methods to verify that the complaint has re-
solved under following conditions:

Conditions noted by the customer.

If a DTC was diagnosed, verify the repair be duplicat-
ing conditions present when the DTC was set as
noted in Failure Records or Freeze Frame data.
Verifying Vehicle Repair
Verification of the vehicle repair will be more compre-
hensive for vehicles with Euro On-Board Diagnostic
(EOBD) system diagnostics. Following a repair, the
technician should perform the following steps:
Important: Follow the steps below when you verify re-
pairs on EOBD systems. Failure to follow these steps
could result in unnecessary repairs.

Review and record the Failure Records and the
Freeze Frame data for the DTC which has been diag-
nosed (Freeze Fame data will only be stored for an A,
B and E type diagnostic and only if the Malfunction
Indicator Lamp has been requested).

Clear the DTC(s).

Operate the vehicle within conditions noted in the
Failure Records and Freeze Frame data.

Monitor the DTC status information for the specific
DTC which has been diagnosed until the diagnostic
test associated with that DTC runs.
EOBD SERVICEABILITY ISSUES
Based on the knowledge gained from Euro On-Board
Diagnostic (OBD) experience in the 1994 and 1995
model years in United Status, this list of non-vehicle
faults that could affect the performance of the Euro On-
Board Diagnostic (EOBD) system has been compiled.
These non-vehicle faults vary from environmental condi-
tions to the quality of fuel used. With the introduction of
EOBD across the entire passenger car, illumination of
the Malfunction Indicator Lamp (MIL) due to a non-ve-
hicle fault could lead to misdiagnosis of the vehicle, in-
creased warranty expense and customer
dissatisfaction. The following list of non-vehicle faults
does not include every possible fault and may not apply
equally to all product lines.
Fuel Quality
Fuel quality is not a new issue for the automotive indus-
try, but its potential for turning on the MIL with EOBD
systems is new.
Fuel additives such as “dry gas” and “octane enhancers”
may affect the performance of the fuel. If this results in
an incomplete combustion or a partial burn, it will set
Diagnostic Trouble Code (DTC) P0300. The Reed Vapor
Pressure of the fuel can also create problems in the fuel
system, especially during the spring and fall months
when severe ambient temperature swings occur. A high
Reed Vapor Pressure could show up as a Fuel Trim
DTC due to excessive canister loading.
Using fuel with the wrong octane rating for your vehicle
may cause driveability problems. Many of the major fuel
companies advertise that using “premium” gasoline will
improve the performance of your vehicle. Most premium

1F–10 ENGINE CONTROLS
DAEWOO M-150 BL2
fuels use alcohol to increase the octane rating of the
fuel. Although alcohol-enhanced fuels may raise the oc-
tane rating, the fuel’s ability to turn into vapor in cold
temperatures deteriorates. This may affect the starting
ability and cold driveability of the engine.
Low fuel levels can lead to fuel starvation, lean engine
operation, and eventually engine misfire.
Non-OEM Parts
The EOBD system has been calibrated to run with Origi-
nal Equipment Manufacturer (OEM) parts. Something
as simple as a high performance-exhaust system that
affects exhaust system back pressure could potentially
interfere with the operation of the Electric Exhaust Gas
Recirculation (EEGR) valve and thereby turn on the
MIL. Small leaks in the exhaust system near the heated
oxygen sensor (HO2S) can also cause the MIL to turn
on.
Aftermarket electronics, such as cellular phones, ster-
eos, and anti-theft devices, may radiate Electromagnet-
ic Interference (EMI) into the control system if they are
improperly installed. This may cause a false sensor
reading and turn on the MIL.
Environment
Temporary environmental conditions, such as localized
flooding, will have an effect on the vehicle ignition sys-
tem. If the ignition system is rain-soaked, it can tempo-
rarily cause engine misfire and turn on the MIL.
Vehicle Marshaling
The transportation of new vehicles from the assembly
plant to the dealership can involve as many as 60 key
cycles within 2 to 3 miles of driving. This type of opera-
tion contributes to the fuel fouling of the spark plugs and
will turn on the MIL with a set DTC P0300.
Poor Vehicle Maintenance
The sensitivity of the EOBD will cause the MIL to turn on
if the vehicle is not maintained properly. Restricted air fil-
ters, fuel filters, and crankcase deposits due to lack of oil
changes or improper oil viscosity can trigger actual ve-
hicle faults that were not previously monitored prior to
EOBD. Poor vehicle maintenance can not be classified
as a “non-vehicle fault,” but with the sensitivity of the
EOBD, vehicle maintenance schedules must be more
closely followed.
Severe Vibration
The Misfire diagnostic measures small changes in the
rotational speed of the crankshaft. Severe driveline
vibrations in the vehicle, such as caused by an exces-
sive amount of mud on the wheels, can have the same
effect on crankshaft speed as misfire and, therefore,
may set DTC P0300.
Related System Faults
Many of the EOBD system diagnostics will not run if the
Engine Control Module (ECM) detects a fault on a re-
lated system or component. One example would be thatif the ECM detected a Misfire fault, the diagnostics on
the catalytic converter would be suspended until the
Misfire fault was repaired. If the Misfire fault is severe
enough, the catalytic converter can be damaged due to
overheating and will never set a Catalyst DTC until the
Misfire fault is repaired and the Catalyst diagnostic is al-
lowed to run to completion. If this happens, the custom-
er may have to make two trips to the dealership in order
to repair the vehicle.
SERIAL DATA COMMUNICATIONS
Keyword 2000 Serial Data
Communications
Government regulations require that all vehicle
manufacturers establish a common communication sys-
tem. This vehicle utilizes the “Keyword 2000” commu-
nication system. Each bit of information can have one of
two lengths: long or short. This allows vehicle wiring to
be reduced by transmitting and receiving multiple sig-
nals over a single wire. The messages carried on Key-
word 2000 data streams are also prioritized. If two
messages attempt to establish communications on the
data line at the same time, only the message with higher
priority will continue. The device with the lower priority
message must wait. The most significant result of this
regulation is that it provides scan tool manufacturers
with the capability to access data from any make or
model vehicle that is sold.
The data displayed on the other scan tool will appear the
same, with some exceptions. Some scan tools will only
be able to display certain vehicle parameters as values
that are a coded representation of the true or actual val-
ue. On this vehicle, the scan tool displays the actual val-
ues for vehicle parameters. It will not be necessary to
perform any conversions from coded values to actual
values.
EURO ON-BOARD DIAGNOSTIC
(EOBD)
Euro On-Board Diagnostic Tests
A diagnostic test is a series of steps, the result of which
is a pass or fail reported to the diagnostic executive.
When a diagnostic test reports a pass result, the diag-
nostic executive records the following data:

The diagnostic test has been completed since the last
ignition cycle.

The diagnostic test has passed during the current
ignition cycle.

The fault identified by the diagnostic test is not cur-
rently active.
When a diagnostic test reports a fail result, the diagnos-
tic executive records the following data:

The diagnostic test has been completed since the last
ignition cycle.

ENGINE CONTROLS 1F–11
DAEWOO M-150 BL2

The fault identified by the diagnostic test is currently
active.

The fault has been active during this ignition cycle.

The operating conditions at the time of the failure.
Remember, a fuel trim Diagnostic Trouble Code (DTC)
may be triggered by a list of vehicle faults. Make use of
all information available (other DTCs stored, rich or lean
condition, etc.) when diagnosing a fuel trim fault.
COMPREHENSIVE COMPONENT
MONITOR DIAGNOSTIC OPERATION
Comprehensive component monitoring diagnostics are
required to monitor emissions-related input and output
powertrain components.
Input Components
Input components are monitored for circuit continuity
and out-of-range values. This includes rationality check-
ing. Rationality checking refers to indicating a fault when
the signal from a sensor does not seem reasonable, i.e.
Throttle Position (TP) sensor that indicates high throttle
position at low engine loads or Manifold Absolute Pres-
sure (MAP) voltage. Input components may include, but
are not limited to, the following sensors:

Vehicle Speed Sensor (VSS).

Crankshaft Position (CKP) sensor.

Throttle Position (TP) sensor.

Engine Coolant Temperature (ECT) sensor.

Camshaft Position (CMP) sensor.

MAP sensor.
In addition to the circuit continuity and rationality check,
the ECT sensor is monitored for its ability to achieve a
steady state temperature to enable closed loop fuel con-
trol.
Output Components
Output components are diagnosed for proper response
to control module commands. Components where func-
tional monitoring is not feasible will be monitored for cir-
cuit continuity and out-of-range values if applicable.
Output components to be monitored include, but are not
limited to the following circuit:

Idle Air Control (IAC) Motor.

Controlled Canister Purge Valve.

A/C relays.

Cooling fan relay.

VSS output.

Malfunction Indicator Lamp (MIL) control.
Refer to “Engine Control Module” and the sections on
Sensors in General Descriptions.
Passive and Active Diagnostic Tests
A passive test is a diagnostic test which simply monitors
a vehicle system or component. Conversely, an activetest, actually takes some sort of action when performing
diagnostic functions, often in response to a failed pas-
sive test. For example, the Electric Exhaust Gas Recir-
culation (EEGR) diagnostic active test will force the
EEGR valve open during closed throttle deceleration
and/or force the EEGR valve closed during a steady
state. Either action should result in a change in manifold
pressure.
Intrusive Diagnostic Tests
This is any Euro On-Board test run by the Diagnostic
Management System which may have an effect on ve-
hicle performance or emission levels.
Warm-Up Cycle
A warm-up cycle means that engine at temperature
must reach a minimum of 70C (160F) and rise at least
22C (40F) over the course of a trip.
Freeze Frame
Freeze Frame is an element of the Diagnostic Manage-
ment System which stores various vehicle information at
the moment an emissions-related fault is stored in
memory and when the MIL is commanded on. These
data can help to identify the cause of a fault.
Failure Records
Failure Records data is an enhancement of the EOBD
Freeze Frame feature. Failure Records store the same
vehicle information as does Freeze Frame, but it will
store that information for any fault which is stored in
Euro On-Board memory, while Freeze Frame stores in-
formation only for emission-related faults that command
the MIL on.
COMMON EOBD TERMS
Diagnostic
When used as a noun, the word diagnostic refers to any
Euro On-Board test run by the vehicle’s Diagnostic Man-
agement System. A diagnostic is simply a test run on a
system or component to determine if the system or com-
ponent is operating according to specification. There are
many diagnostics, shown in the following list:

Misfire.

Oxygen sensors (O2S)

Heated oxygen sensor (HO2S)

Electric Exhaust Gas Recirculation (EEGR)

Catalyst monitoring
Enable Criteria
The term “enable criteria” is engineering language for
the conditions necessary for a given diagnostic test to
run. Each diagnostic has a specific list of conditions
which must be met before the diagnostic will run.
“Enable criteria” is another way of saying “conditions re-
quired.”

1F–12 ENGINE CONTROLS
DAEWOO M-150 BL2
The enable criteria for each diagnostic is listed on the
first page of the Diagnostic Trouble Code (DTC) descrip-
tion under the heading “Conditions for Setting the DTC.”
Enable criteria varies with each diagnostic and typically
includes, but is not limited to the following items:

Engine speed.

Vehicle speed

Engine Coolant Temperature (ECT)

Manifold Absolute Pressure (MAP)

Barometric Pressure (BARO)

Intake Air Temperature (IAT)

Throttle Position (TP)

High canister purge

Fuel trim

A/C on
Trip
Technically, a trip is a key-on run key-off cycle in which
all the enable criteria for a given diagnostic are met, al-
lowing the diagnostic to run. Unfortunately, this concept
is not quite that simple. A trip is official when all the en-
able criteria for a given diagnostic are met. But because
the enable criteria vary from one diagnostic to another,
the definition of trip varies as well. Some diagnostics are
run when the vehicle is at operating temperature, some
when the vehicle first starts up; some require that the
vehicle cruise at a steady highway speed, some run only
when the vehicle is at idle. Some run only immediately
following a cold engine start-up.
A trip then, is defined as a key-on run-key off cycle in
which the vehicle is operated in such a way as to satisfy
the enable criteria for a given diagnostic, and this diag-
nostic will consider this cycle to be one trip. However,
another diagnostic with a different set of enable criteria
(which were not met) during this driving event, would not
consider it a trip. No trip will occur for that particular
diagnostic until the vehicle is driven in such a way as to
meet all the enable criteria.
Diagnostic Information
The diagnostic charts and functional checks are de-
signed to locate a faulty circuit or component through a
process of logical decisions. The charts are prepared
with the requirement that the vehicle functioned correct-
ly at the time of assembly and that there are not multiple
faults present.
There is a continuous self-diagnosis on certain control
functions. This diagnostic capability is complimented by
the diagnostic procedures contained in this manual. The
language of communicating the source of the malfunc-
tion is a system of diagnostic trouble codes. When a
malfunction is detected by the control module, a DTC is
set, and the Malfunction Indicator Lamp (MIL) is illumi-
nated.
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is required by
Euro On-Board Diagnostics (EOBD) to illuminate under
a strict set of guidelines.
Basically, the MIL is turned on when the Engine Control
Module (ECM) detects a DTC that will impact the vehicle
emissions.
The MIL is under the control of the Diagnostic Execu-
tive. The MIL will be turned on if an emissions-related
diagnostic test indicates a malfunction has occurred. It
will stay on until the system or component passes the
same test for three consecutive trips with no emissions
related faults.
Extinguishing the MIL
When the MIL is on, the Diagnostic Executive will turn
off the MIL after three consecutive trips that a “test
passed” has been reported for the diagnostic test that
originally caused the MIL to illuminate. Although the MIL
has been turned off, the DTC will remain in the ECM
memory (both Freeze Frame and Failure Records) until
forty (40) warm-up cycles after no faults have been com-
pleted.
If the MIL was set by either a fuel trim or misfire-related
DTC, additional requirements must be met. In addition
to the requirements stated in the previous paragraph,
these requirements are as follows:

The diagnostic tests that are passed must occur with
375 rpm of the rpm data stored at the time the last
test failed.

Plus or minus ten percent of the engine load that was
stored at the time the last test failed. Similar engine
temperature conditions (warmed up or warming up)
as those stored at the time the last test failed.
Meeting these requirements ensures that the fault which
turned on the MIL has been corrected.
The MIL is on the instrument panel and has the following
functions:

It informs the driver that a fault affecting the vehicle’s
emission levels has occurred and that the vehicle
should be taken for service as soon as possible.

As a system check, the MIL will come on with the key
ON and the engine not running. When the engine is
started, the MIL will turn OFF.

When the MIL remains ON while the engine is run-
ning, or when a malfunction is suspected due to a
driveability or emissions problem, an EOBD System
Check must be performed. The procedures for these
checks are given in EOBD System Check. These
checks will expose faults which may not be detected
if other diagnostics are performed first.