battery DAEWOO MATIZ 2003 Service Owner's Guide
[x] Cancel search | Manufacturer: DAEWOO, Model Year: 2003, Model line: MATIZ, Model: DAEWOO MATIZ 2003Pages: 1184, PDF Size: 36 MB
Page 85 of 1184
ENGINE ELECTRICAL 1E–29
DAEWOO M-150 BL2
D12E740A
4–6 Nm
80–110 NmTighten the generator pulley nut to 80–110 Nm
(59–81 lb-ft) (d).
Tighten the through-bolts to 4–6 Nm (35–53 lb-in)
(e).
D102E741
GENERATOR (B-TYPE: DAC)
Disassembly Procedure
1. Remove the generator. Refer to “Generator” in this
section.
2. Remove the cover from the generator.
Remove the battery positive terminal nut (1).
Remove the cover (2).
a. Cover.
D102E742
3. Remove the regulator / brush holder / rectifier assem-
bly.
Remove the stator coil lead and rectifier diode lead
connections (1).
D102E743
Remove the rectifier bolts (2).
Remove the rectifier / regulator screw (3).
Remove the brush holder / regulator screw (4).
Remove the regulator screw (5).
Remove the regulator / brush holder / rectifier as-
sembly (6).
Page 90 of 1184
1E–34 ENGINE ELECTRICAL
DAEWOO M-150 BL2
D12E760A
4–7 Nm
4–6 NmTighten the through-bolts to 4–6 Nm (35–53 lb-in)
(f).
Tighten the battery positive terminal nut to 4–7
Nm (35–62 lb-in) (g).
D102E761
DISTRIBUTOR ASSEMBLY
Disassembly Procedure
1. Remove the distributor. Refer to “Distributor” in this
section.
2. Remove the cap, seal and rotor from the distributor
housing.
Remove the bolts (1).
Remove the distributor cap (2).
Remove the seal (3).
Remove the rotor (4).
D102E762
Inspect the cap for cracks or damage (a).
Inspect the cap electrode for damage / wear or car-
bon traces (b).
Inspect the rotor for damage or carbon traces (c).
D102E763
3. Remove the inner / outer cover from the distributor
housing.
Remove the outer cover (1).
Remove the screws (2).
Remove the inner cover (3).
Page 98 of 1184
1E–42 ENGINE ELECTRICAL
DAEWOO M-150 BL2
BATTERY SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
BatteryType–MF–
CapacityAH35–
Cold Cranking AmpsCCA246–
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Distributor Bolts10–16–89–142
Battery Retainer Clamp–to–Battery Rod Nuts6–8–53–71
Battery Carrier Tray Bolts9–12–80–106
Battery Cable Nuts9–12–80–106
Starter field Connector Nut9–12–80–106
Starter Through–Bolts4–6–35–53
Starter Mounting Bolts55–6541–48–
Starter Solenoid Assembly Screws6–8–53–71
Starter Solenoid Nuts9–12–80–106
Spark Plug20–3015–22–
Generator Through–Bolts4–6–35–53
Generator Drive End Nut80–11 059–81–
Generator Battery Lead Connector Nut4–7–35–62
Generator Bearing Plate Bolt6–8–53–71
Generator Brush Holder / Rectifier Screw9–12–80–106
Generator Belt Tension Adjusting Bolt18–2813–21–
Generator Shackle Bracket Bolt45–5533–41–
Generator Lower Bracket–to–Generator Bolt/Nut18–2813–21–
Ground Bolt35–4126–30–
Ignition Coil Screw4–7–35–62
Ignition Coil Bracket Bolt9–12–80–106
Page 99 of 1184
DAEWOO M-150 BL2
SECTION 1F
ENGINE CONTROLS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Description and Operation 1F-4. . . . . . . . . . . . . . . . . .
Ignition System Operation 1F-4. . . . . . . . . . . . . . . . . .
Electronic Ignition System Ignition Coil 1F-4. . . . . . .
Crankshaft Position Sensor 1F-4. . . . . . . . . . . . . . . . .
Camshaft Position Sensor 1F-4. . . . . . . . . . . . . . . . . .
Idle Air System Operation 1F-4. . . . . . . . . . . . . . . . . .
Fuel Control System Operation 1F-4. . . . . . . . . . . . . .
Evaporative Emission Control System
Operation 1F-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlled Charcoal Canister 1F-5. . . . . . . . . . . . . . . .
Positive Crankcase Ventilation Control System
Operation 1F-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Coolant Temperature Sensor 1F-6. . . . . . . . .
Throttle Position Sensor 1F-6. . . . . . . . . . . . . . . . . . . .
Catalyst Monitor Oxygen Sensors 1F-6. . . . . . . . . . .
Electric Exhaust Gas Recirculation Valve 1F-6. . . . .
Intake Air Temperature Sensor 1F-7. . . . . . . . . . . . . .
Idle Air Control Valve 1F-7. . . . . . . . . . . . . . . . . . . . . .
Manifold Absolute Pressure Sensor 1F-7. . . . . . . . . .
Engine Control Module 1F-8. . . . . . . . . . . . . . . . . . . . .
Fuel Injector 1F-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Cutoff Switch (Inertia Switch) 1F-8. . . . . . . . . . .
Knock Sensor 1F-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Reluctance (VR) Sensor 1F-8. . . . . . . . . . . .
Octane Number Connector 1F-8. . . . . . . . . . . . . . . . .
Strategy-Based Diagnostics 1F-9. . . . . . . . . . . . . . . .
EOBD Serviceability Issues 1F-9. . . . . . . . . . . . . . . . .
Serial Data Communications 1F-10. . . . . . . . . . . . . . .
Euro On-Board Diagnostic (EOBD) 1F-10. . . . . . . . .
Comprehensive Component Monitor Diagnostic
Operation 1F-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common EOBD Terms 1F-11. . . . . . . . . . . . . . . . . . . .
DTC Types 1F-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading Diagnostic Trouble Codes 1F-13. . . . . . . . .
Primary System-Based Diagnostics 1F-15. . . . . . . . Diagnostic Information and Procedures 1F-17. . . .
System Diagnosis 1F-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Aids 1F-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Learn Procedure 1F-17. . . . . . . . . . . . . . . . . . . . .
Euro On-Board Diagnostic (EOBD) System
Check 1F-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECM Output Diagnosis 1F-20. . . . . . . . . . . . . . . . . . . .
Multiple ECM Information Sensor DTCs Set 1F-21. .
Engine Cranks But Will Not Run 1F-25. . . . . . . . . . . .
No Malfunction Indicator Lamp 1F-30. . . . . . . . . . . . .
Malfunction Indicator Lamp On Steady 1F-32. . . . . .
Fuel System Diagnosis 1F-34. . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay Circuit Check 1F-36. . . . . . . . . . . .
Main Relay Circuit Check 1F-38. . . . . . . . . . . . . . . . . .
Manifold Absolute Pressure Check 1F-40. . . . . . . . . .
Idle Air Control System Check 1F-42. . . . . . . . . . . . .
Ignition System Check 1F-45. . . . . . . . . . . . . . . . . . . .
Engine Cooling Fan Circuit Check 1F-48. . . . . . . . . .
Data Link Connector Diagnosis 1F-52. . . . . . . . . . . . .
Fuel Injector Balance Test 1F-54. . . . . . . . . . . . . . . . .
Diagnostic Trouble Code Diagnosis 1F-55. . . . . . . .
Clearing Trouble Codes 1F-55. . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 1F-55. . . . . . . . . . . . . . . . .
DTC P0107 Manifold Absolute Pressure Sensor
Low Voltage 1F-58. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0108 Manifold Pressure Sensor High
Voltage 1F-62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0112 Intake Air Temperature Sensor Low
Voltage 1F-66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0113 Intake Air Temperature Sensor High
Voltage 1F-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0117 Engine Coolant Temperature Sensor
Low Voltage 1F-72. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0118 Engine Coolant Temperature Sensor
High Voltage 1F-74. . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 103 of 1184
ENGINE CONTROLS 1F–5
DAEWOO M-150 BL2
fuel is delivered under one of several conditions, called
“modes.’’
Starting Mode
When the ignition is turned ON, the ECM turns the fuel
pump relay on for 2 seconds. The fuel pump then builds
fuel pressure. The ECM also checks the Engine Coolant
Temperature (ECT) sensor and the Throttle Position
(TP) sensor and determines the proper air/fuel ratio for
starting the engine. The ECM controls the amount of
fuel delivered in the starting mode by changing how long
the fuel injector is turned on and off. This is done by
“pulsing’’ the fuel injectors for very short times.
Run Mode
The run mode has two conditions called “open loop’’ and
“closed loop.’’
Open Loop
When the engine is first started and it is above 400 rpm,
the system goes into “open loop’’ operation. In “open
loop,’’ the ECM ignores the signal from the O2S and cal-
culates the air/fuel ratio based on inputs from the ECT
sensor and the MAP sensor. The ECM stays in ”open
loop” until the following conditions are met:
The O2S has a varying voltage output, showing that it
is hot enough to operate properly.
The ECT sensor is above a specified temperature.
A specific amount of time has elapsed after starting
the engine.
Closed Loop
The specific values for the above conditions vary with
different engines and are stored in the Electronically
Erasable Programmable Read-Only Memory (EE-
PROM). When these conditions are met, the system
goes into “closed loop” operation. In “closed loop,” the
ECM calculates the air/fuel ratio (fuel injector on-time)
based on the signals from the oxygen sensors. This al-
lows the air/fuel ratio to stay very close to 14.7 to 1.
Acceleration Mode
The ECM responds to rapid changes in throttle position
and airflow and provides extra fuel.
Deceleration Mode
The ECM responds to changes in throttle position and
airflow and reduces the amount of fuel. When decelera-
tion is very fast, the ECM can cut off fuel completely for
short periods of time.
Battery Voltage Correction Mode
When battery voltage is low, the ECM can compensate
for a weak spark delivered by the ignition module by us-
ing the following methods:
Increasing the fuel injector pulse width.
Increasing the idle speed rpm.
Increasing the ignition dwell time.
Fuel Cut-Off Mode
No fuel is delivered by the fuel injectors when the ignition
is off. This prevents dieseling or engine run-on. Also, the
fuel is not delivered if there are no reference pulses re-
ceived from the CKP sensor. This prevents flooding.
EVAPORATIVE EMISSION CONTROL
SYSTEM OPERATION
The basic Evaporative Emission (EVAP) control system
used is the charcoal canister storage method. This
method transfers fuel vapor from the fuel tank to an acti-
vated carbon (charcoal) storage canister which holds
the vapors when the vehicle is not operating. When the
engine is running, the fuel vapor is purged from the car-
bon element by intake airflow and consumed in the nor-
mal combustion process.
Gasoline vapors from the fuel tank flow into the tube la-
beled TANK. These vapors are absorbed into the car-
bon. The canister is purged by Engine Control Module
(ECM) when the engine has been running for a specified
amount of time. Air is drawn into the canister and mixed
with the vapor. This mixture is then drawn into the intake
manifold.
The ECM supplies a ground to energize the controlled
charcoal canister purge solenoid valve. This valve is
Pulse Width Modulated (PWM) or turned on and off sev-
eral times a second. The controlled charcoal canister
purge PWM duty cycle varies according to operating
conditions determined by mass airflow, fuel trim, and in-
take air temperature.
Poor idle, stalling, and poor driveability can be caused
by the following conditions:
An inoperative controlled canister purge valve.
A damaged canister.
Hoses that are split, cracked, or not connected to the
proper tubes.
CONTROLLED CHARCOAL
CANISTER
The controlled charcoal canister is an emission control
device containing activated charcoal granules. The con-
trolled charcoal canister is used to store fuel vapors from
the fuel tank. Once certain conditions are met, the En-
gine Control Module (ECM) activates the controlled
charcoal canister purge solenoid, allowing the fuel va-
pors to be drawn into the engine cylinders and burned.
POSITIVE CRANKCASE
VENTILATION CONTROL SYSTEM
OPERATION
A Positive Crankcase Ventilation (PCV) control system
is used to provide complete use of the crankcase va-
Page 105 of 1184
ENGINE CONTROLS 1F–7
DAEWOO M-150 BL2
manifold to decrease combustion temperature. The
amount of exhaust gas recirculated is controlled by vari-
ations in vacuum and exhaust back pressure. If too
much exhaust gas enters, combustion will not take
place. For this reason, very little exhaust gas is allowed
to pass through the valve, especially at idle.
The EEGR valve is usually open under the following
conditions:
Warm engine operation.
Above idle speed.
Results of Incorrect Operation
Too much EEGR flow tends to weaken combustion,
causing the engine to run roughly or to stop. With too
much EEGR flow at idle, cruise, or cold operation, any of
the following conditions may occur:
The engine stops after a cold start.
The engine stops at idle after deceleration.
The vehicle surges during cruise.
Rough idle.
If the EEGR valve stays open all the time, the engine
may not idle. Too little or no EEGR flow allows combus-
tion temperatures to get too high during acceleration
and load conditions. This could cause the following con-
ditions:
Spark knock (detonation)
Engine overheating
Emission test failure
INTAKE AIR TEMPERATURE
SENSOR
The Intake Air Temperature (IAT) sensor is a thermistor,
a resistor which changes value based on the tempera-
ture of the air entering the engine. Low temperature pro-
duces a high resistance (100 kohms at –40C [–40F]),
while high temperature causes a low resistance (70
ohms at 130C [266F]).
The Engine Control Module (ECM) provides 5 volts to
the IAT sensor through a resistor in the ECM and mea-
sures the change in voltage to determine the IAT. The
voltage will be high when the manifold air is cold and low
when the air is hot. The ECM knows the intake IAT by
measuring the voltage.
The IAT sensor is also used to control spark timing when
the manifold air is cold.
A failure in the IAT sensor circuit sets a diagnostic
trouble code P0112 or P0113.
IDLE AIR CONTROL VALVE
Notice: Do not attempt to remove the protective cap
and readjust the stop screw. Misadjustment may result
in damage to the Idle Air Control (IAC) valve or to the
throttle body.The IAC valve is mounted on the throttle body where it
controls the engine idle speed under the command of
the Engine Control Module (ECM). The ECM sends volt-
age pulses to the IAC valve motor windings, causing the
IAC valve pintle to move in or out a given distance (a
step or count) for each pulse. The pintle movement con-
trols the airflow around the throttle valves which, in turn,
control the engine idle speed.
The desired idle speeds for all engine operating condi-
tions are programmed into the calibration of the ECM.
These programmed engine speeds are based on the
coolant temperature, the park/neutral position switch
status, the vehicle speed, the battery voltage, and the
A/C system pressure, if equipped.
The ECM “learns” the proper IAC valve positions to
achieve warm, stabilized idle speeds (rpm) desired for
the various conditions (park/neutral or drive, A/C on or
off, if equipped). This information is stored in ECM ”keep
alive” memories (information is retained after the ignition
is turned off). All other IAC valve positioning is calcu-
lated based on these memory values. As a result, en-
gine variations due to wear and variations in the
minimum throttle valve position (within limits) do not af-
fect engine idle speeds. This system provides correct
idle control under all conditions. This also means that
disconnecting power to the ECM can result in incorrect
idle control or the necessity to partially press the accel-
erator when starting until the ECM relearns idle control.
Engine idle speed is a function of total airflow into the
engine based on the IAC valve pintle position, the
throttle valve opening, and the calibrated vacuum loss
through accessories. The minimum throttle valve posi-
tion is set at the factory with a stop screw. This setting
allows enough airflow by the throttle valve to cause the
IAC valve pintle to be positioned a calibrated number of
steps (counts) from the seat during “controlled” idle op-
eration. The minimum throttle valve position setting on
this engine should not be considered the “minimum idle
speed,” as on other fuel injected engines. The throttle
stop screw is covered with a plug at the factory following
adjustment.
If the IAC valve is suspected as being the cause of im-
proper idle speed, refer to “Idle Air Control System
Check” in this section.
MANIFOLD ABSOLUTE PRESSURE
SENSOR
The Manifold Absolute Pressure (MAP) sensor mea-
sures the changes in the intake manifold pressure which
result from engine load and speed changes and con-
verts these to a voltage output.
A closed throttle on engine coast down produces a rela-
tively low MAP output. MAP is the opposite of vacuum.
When manifold pressure is high, vacuum is low. The
MAP sensor is also used to measure barometric pres-
sure. This is performed as part of MAP sensor calcula-
Page 112 of 1184
1F–14 ENGINE CONTROLS
DAEWOO M-150 BL2
termittent fault will also be erased from memory. If the
fault that caused the DTC to be stored into memory has
been corrected, the Diagnostic Executive will begin to
count the ‘‘warm-up” cycles with no further faults de-
tected, the DTC will automatically be cleared from the
Engine Control Module (ECM) memory.
To clear DTCs, use the diagnostic scan tool.
It can’t cleared DTCs without the diagnostic scan tool.
So you must use the diagnostic scan tool.
Notice: To prevent system damage, the ignition key
must be OFF when disconnecting or reconnecting bat-
tery power.
The power source to the control module. Examples:
fuse, pigtail at battery ECM connectors, etc.
The negative battery cable. (Disconnecting the nega-
tive battery cable will result in the loss of other Euro
On-Board memory data, such as preset radio tuning.)
DTC Modes
On Euro On-Board Diagnostic (EOBD) passenger cars
there are five options available in the scan tool DTC
mode to display the enhanced information available. A
description of the new modes, DTC Info and Specific
DTC, follows. After selecting DTC, the following menu
appears:
DTC Info.
Specific DTC.
Freeze Frame.
Fail Records (not all applications).
Clear Info.
The following is a brief description of each of the sub
menus in DTC Info and Specific DTC. The order in
which they appear here is alphabetical and not neces-
sarily the way they will appear on the scan tool.
DTC Information Mode
Use the DTC info mode to search for a specific type of
stored DTC information. There are seven choices. The
service manual may instruct the technician to test for
DTCs in a certain manner. Always follow published ser-
vice procedures.
To get a complete description of any status, press the
‘‘Enter” key before pressing the desired F-key. For ex-
ample, pressing ‘‘Enter” then an F-key will display a defi-
nition of the abbreviated scan tool status.
DTC Status
This selection will display any DTCs that have not run
during the current ignition cycle or have reported a test
failure during this ignition up to a maximum of 33 DTCs.
DTC tests which run and pass will cause that DTC num-
ber to be removed from the scan tool screen.
Fail This Ign. (Fail This Ignition)
This selection will display all DTCs that have failed dur-
ing the present ignition cycle.
History
This selection will display only DTCs that are stored in
the ECM’s history memory. It will not display Type B
DTCs that have not requested the Malfunction Indicator
Lamp (MIL). It will display all type A, B and E DTCs that
have requested the MIL and have failed within the last
40 warm-up cycles. In addition, it will display all type C
and type D DTCs that have failed within the last 40
warm-up cycles.
Last Test Fail
This selection will display only DTCs that have failed the
last time the test ran. The last test may have run during
a previous ignition cycle if a type A or type B DTC is dis-
played. For type C and type D DTCs, the last failure
must have occurred during the current ignition cycle to
appear as Last Test Fail.
MIL Request
This selection will display only DTCs that are requesting
the MIL. Type C and type D DTCs cannot be displayed
using this option. This selection will report type B and E
DTCs only after the MIL has been requested.
Not Run SCC (Not Run Since Code Clear)
This option will display up to 33 DTCs that have not run
since the DTCs were last cleared. Since the displayed
DTCs have not run, their condition (passing or failing) is
unknown.
Test Fail SCC (Test Failed Since Code
Clear)
This selection will display all active and history DTCs
that have reported a test failure since the last time DTCs
were cleared. DTCs that last failed more than 40 warm-
up cycles before this option is selected will not be dis-
played.
Specific DTC Mode
This mode is used to check the status of individual diag-
nostic tests by DTC number. This selection can be ac-
cessed if a DTC has passed, failed or both. Many EOBD
DTC mode descriptions are possible because of the ex-
tensive amount of information that the diagnostic execu-
tive monitors regarding each test. Some of the many
possible descriptions follow with a brief explanation.
The “F2” key is used, in this mode, to display a descrip-
tion of the DTC. The “Ye s” and “No” keys may also be
used to display more DTC status information. This
selection will only allow entry of DTC numbers that are
supported by the vehicle being tested. If an attempt is,
Page 115 of 1184
ENGINE CONTROLS 1F–17
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
SYSTEM DIAGNOSIS
DIAGNOSTIC AIDS
If an intermittent problem is evident, follow the guide-
lines below.
Preliminary Checks
Before using this section you should have already per-
formed the “Euro On-Board Diagnostic (EOBD) System
Check.”
Perform a thorough visual inspection. This inspection
can often lead to correcting a problem without further
checks and can save valuable time. Inspect for the fol-
lowing conditions:
Engine Control Module (ECM) grounds for being
clean, tight, and in their proper location.
Vacuum hoses for splits, kinks, collapsing and proper
connections as shown on the Vehicle Emission Con-
trol Information label. Inspect thoroughly for any type
of leak or restriction.
Air leaks at the throttle body mounting area and the
intake manifold sealing surfaces.
Ignition wires for cracks, hardness, proper routing,
and carbon tracking.
Wiring for proper connections.
Wiring for pinches or cuts.
Diagnostic Trouble Code Tables
Do not use the Diagnostic Trouble Code (DTC) tables to
try and correct an intermittent fault. The fault must be
present to locate the problem.
Incorrect use of the DTC tables may result in the unnec-
essary replacement of parts.
Faulty Electrical Connections or Wiring
Most intermittent problems are caused by faulty electri-
cal connections or wiring. Perform a careful inspection
of suspect circuits for the following:
Poor mating of the connector halves.
Terminals not fully seated in the connector body.
Improperly formed or damaged terminals. All connec-
tor terminals in a problem circuit should be carefullyinspected, reformed, or replaced to insure contact
tension.
Poor terminal-to-wire connection. This requires re-
moving the terminal from the connector body.
Road Test
If a visual inspection does not find the cause of the prob-
lem, the vehicle can be driven with a voltmeter or a scan
tool connected to a suspected circuit. An abnormal volt-
age or scan tool reading will indicate that the problem is
in that circuit.
If there are no wiring or connector problems found and a
DTC was stored for a circuit having a sensor, except for
DTC P0171 and DTC P0172, replace the sensor.
Intermittent Malfunction Indicator Lamp
(MIL)
An intermittent Malfunction Indicator Lamp(MIL) with no
DTC present may be caused by the following:
Improper installation of electrical options such as
lights, two way radios, sound, or security systems.
MIL driver wire intermittently shorted to ground.
Fuel System
Some intermittent driveability problems can be attrib-
uted to poor fuel quality. If a vehicle is occasionally run-
ning rough, stalling, or otherwise performing badly, ask
the customer about the following fuel buying habits:
Do they always buy from the same source? If so, fuel
quality problems can usually be discounted.
Do they buy their fuel from whichever fuel station that
is advertising the lowest price? If so, check the fuel
tank for signs of debris, water, or other contamina-
tion.
IDLE LEARN PROCEDURE
Whenever the battery cables, the Engine Control Mod-
ule (ECM), or the fuse is disconnected or replaced, the
following idle learn procedure must be performed:
1. Turn the ignition ON for 10 seconds.
2. Turn the ignition OFF for 10 seconds.
Page 124 of 1184
1F–26 ENGINE CONTROLS
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
12
Check for an open or short in the wires between
CKP sensor connector and ECM connector and
repair as need.
Is the repair complete?
–
Go to Step 2
–
13
1. Disconnect electronic Ignition (EI) system ignition
coil connector to prevent the vehicle from starting.
2. Measure the voltage at ECM connector terminal
24 and 54 by backprobing the ECM connector.
Are the voltage readings near the value specified?
0.4 V with
ignition ON,
2.0 V during
cranking
Go to Step 15Go to Step 14
14Replace the CKP sensor.
Is the repair complete?–Go to Step 2–
15
1. Turn the ignition OFF.
2. Disconnect the electrical connector at EI system
ignition coil.
3. Connect a test light between terminal 1 of the EI
system ignition coil connector and ground.
4. Turn the ignition ON.
Is the test light on?
–
Go to Step 17Go to Step 16
16
Check for open in wire between the battery and EI
system ignition coil connector terminal 1 and repair
as needed.
Is the repair complete?
–
Go to Step 2
–
17
1. Turn the ignition OFF.
2. Disconnect ECM connector and EI system
ignition coil connector.
3. Measure the resistance between following
terminals:
Terminal 2 of ignition coil and terminal 1 of
ECM connector.
Terminal 3 of ignition coil and terminal 32 of
ECM connector.
Terminal 4 of ignition coil and terminal 31 of
ECM connector.
Are the resistance within the value specified?
0 ΩGo to Step 19Go to Step 18
18Check for open circuit and repair as needed.
Is the repair complete?–Go to Step 2–
19
1. Measure the resistance between following
terminals:
Terminal 1 and 2 of ignition coil.
Terminal 3 and 4 of ignition coil.
Are the resistance within the value specified?
2. Remove the high tension cable.
3. Measure the resistance between second coil.
Between 1 and 4
Between 2 and 3
Are the resistance within the value specified?
0.9Ω
5.3 kΩ
Go to Step 21Go to Step 20
20Replace the EI system ignition coil.
Is the repair complete?–Go to Step 2–
Page 127 of 1184
ENGINE CONTROLS 1F–29
DAEWOO M-150 BL2
Engine Cranks But Will Not Run (Cont’d)
StepActionValue(s)YesNo
42
1. Turn the ignition OFF.
2. Connect test light between fuel injector harness
connector 2 and battery positive.
3. Crank the engine.
4. Repeat step 2 and 3 for each of the remaining
fuel injectors.
Does the test light flash for all of the fuel injectors?
–
Go to Step 43Go to Step 46
43
Measure the resistance of each fuel injectors.
Is the resistance within the value specified.
Note: the resistance will increase slightly at higher
temperature.
13.75–15.25
ΩSystem OKGo to Step 44
44
Replace any of the fuel injectors with a resistance
out of specification.
Is the repair complete?
–
Go to Step 2
–
45
1. Inspect the fuse EF19 in engine fuse block.
2. Check for an open between the circuit from
terminal 2 of the three fuel injectors and terminal
87 of main relay.
Is the problem found?
–
Go to Step 48
Go to “Main
Relay Circuit
Check”
46
Measure the resistance between following terminals.
Terminal 1 of injector 1 connector and terminal 30
of ECM connector.
Terminal 1 of injector 2 connector and terminal 58
of ECM connector.
Terminal 1 of injector 3 connector and terminal 89
of ECM connector.
Does the resistance within the specified value?
0 ΩGo to Step 49Go to Step 47
47Repair the open fuel injector harness wire(s).
Is the repair complete?–Go to Step 2–
48Replace the fuse or repair the wiring as needed.
Is the repair complete?–Go to Step 2–
49Replace the ECM.
Is the repair complete?–Go to Step 2–