key DODGE NEON 1999 Service Owner's Guide

transmitter vehicle access codes into the memory of
the immobilizer receiver. Refer to the Vehicle Theft
Security System menu item on the DRB scan tool for
the procedures.
The immobilizer receiver recognizes the Lock and
Unlock signals received from the programmed immo-
bilizer transmitters. If the code sent by the key fob
transmitter is recognized as valid by the Immobilizer
module, it will decode the Crankshaft Position Sensor
signal, enable the starter circuit, and allow the
engine to run.
The immobilizer receiver is mounted to the dash
panel with a hook and loop fastener patch. It is
located behind the instrument cluster and above the
heater-A/C housing. The receiver is connected to the
dash panel cross-body wiring harness. (Fig. 1)
For diagnosis of the vehicle immobilizer receiver or
the CCD data bus, a DRB scan tool is required. Refer
to the Vehicle Theft Security System menu item of
the DRB scan tool for the procedures. The immobi-
lizer receiver contains no servicable parts. If faulty,
the unit must be replaced.
IMMOBILIZER TRANSMITTER
The vehicle immobilizer system includes two trans-
mitters that are supplied with the vehicle when it isshipped from the factory. Each of the two transmit-
ters is equipped with two buttons labeled with Inter-
national Standards Organization (ISO) symbols for
Lock, and Unlock. Two spare batteries (enough for
one transmitter) are also shipped with the transmit-
ters. The transmitters are equipped with a key ring
and are designed to serve as a key fob. The operating
range of the radio frequency transmitter signal is up
to 7 meters (23 feet) from the immobilizer receiver.
Each transmitter has a different vehicle access
code, which must be programmed into the memory of
the immobilizer receiver in the vehicle in order to
operate the immobilizer system. The two transmit-
ters shipped with the vehicle have their vehicle
access codes programmed into the receiver at the fac-
tory. A DRB scan tool must be used to program new
or additional transmitter vehicle access codes into
the memory of the immobilizer receiver. Refer to the
Vehicle Theft Security System menu item on the
DRB scan tool for the procedures.
Each transmitter operates on two Duracell DL2016
(or equivalent) batteries. Typical battery life is from
one to two years.
POWER-UP MODE
When the vehicle immobilizer system senses that
the vehicle battery has been disconnected and recon-
nected, it enters its power-up mode. If the immobi-
lizer system was armed prior to the battery
disconnect, the system remains armed when the bat-
tery is reconnected.
If the immobilizer system was disarmed prior to
the battery disconnect, the system will remain dis-
armed if the battery is reconnected within five min-
utes. The system will passively arm itself when the
battery is reconnected more than five minutes after a
battery disconnect or failure. After any passive arm-
ing, the system will have to be actively disarmed
using one of the transmitters.
The power-up mode logic also applies if the battery
goes dead, and battery jump-starting is attempted.
The engine no-run feature will prevent the engine
from operating until the vehicle immobilizer system
has been actively disarmed.
DIAGNOSIS AND TESTING
IMMOBILIZER DIAGNOSIS
Refer to the 1998 PL Powertrain Diagnostic Man-
ual for complete diagnostic procedures of the immo-
bilizer system.
Fig. 1 Immobilizer Module Location
8Q - 2 IMMOBILIZER SYSTEMPL
DESCRIPTION AND OPERATION (Continued)

CHIME WARNING/REMINDER SYSTEM
CONTENTS
page page
GENERAL INFORMATION
INTRODUCTION......................... 1
DIAGNOSIS AND TESTING
CHIME SYSTEM CONDITIONS.............. 1
FASTEN SEAT BELTS..................... 1
HEADLAMPS LEFT ON.................... 1KEY LEFT IN IGNITION SWITCH............ 1
REMOVAL AND INSTALLATION
CHIME................................. 2
HEADLAMP SWITCH..................... 2
KEY-IN SWITCH......................... 2
SEAT BELT BUCKLE...................... 2
GENERAL INFORMATION
INTRODUCTION
WARNING: ON VEHICLES EQUIPPED WITH AN
AIRBAG, REFER TO THE AIRBAG PORTION OF
THIS SECTION FOR STEERING WHEEL OR SWITCH
REMOVAL AND INSTALLATION PROCEDURES.
The seat belt reminder system uses both visual
and audible signals. A combined seat belt and key
reminder chime with a red light on the instrument
panel.
The system will always illuminate the seat belt
reminder lamp for four to eight seconds when the
ignition switch is turned to the ON position. The
CHIME will sound during the same time interval if
the driver's seat belt is not fastened. Passenger belts
are not connected to the system. The chime will acti-
vate if the drivers door is opened and:
²The key is in the ignition switch, with the igni-
tion switch in either the OFF or accessory (ACC)
position
²The head lamps are ON.
The chime is part of the instrument cluster.
NOTE: This group covers both Left-Hand Drive
(LHD) and Right-Hand Drive (RHD) versions of this
model. Whenever required and feasible, the RHD
versions of affected vehicle components have been
constructed as mirror-image of the LHD versions.
While most of the illustrations used in this group
represent only the LHD version, the diagnostic and
service procedures outlined can generally be
applied to either version. Exceptions to this rule
have been clearly identified as LHD, RHD, or Export
if a special illustration or procedure is required.
DIAGNOSIS AND TESTING
FASTEN SEAT BELTS
To test the fasten seat belts function, turn the igni-
tion switch to the ON position with the driver's seat
belt unbuckled and fully retracted. The seat belt
warning lamp should light for four to eight seconds
and the tone should sound three to five times.
HEADLAMPS LEFT ON
To test the headlamps left on function:
²Turn headlamps
²Driver's door open
²Key removed from the ignition switch
Chime should sound until headlamps are turned
off or driver's door is closed.
KEY LEFT IN IGNITION SWITCH
To test the key left in ignition function, insert key
into the ignition and open driver's door. Chime
should sound until key is removed from ignition or
driver's door is closed.
CHIME SYSTEM CONDITIONS
The cluster harness connector, J1 is car right and
the J2 is car left.
NO TONE WHEN IGNITION SWITCH IS
TURNED ON AND DRIVERS SEAT BELT IS
UNBUCKLED
(1) Using an ohmmeter, with the seat belt fully
retracted, check for continuity to ground at Pin 4 of
the J1 wire harness connector (Fig. 1). If OK, go to
step 2. If not OK, repair as necessary .
(2) Check for continuity to ground at Pin 8 of the
J1 wire harness connector. If OK, go to Step 3. If not
OK, repair as necessary.
(3) Using voltmeter, check for battery feed at Pin 6
of the J1 wire harness connector. Check for ignition
feed at Pin 5 of the J1 wire harness connector. If not
OK, repair as necessary.
PLCHIME WARNING/REMINDER SYSTEM 8U - 1

NO FASTEN SEAT BELT LAMP WHEN
IGNITION SWITCH IS ON.
(1) Check for burned out lamp.
(2) Check for battery feed at cluster wire harness
connector terminal J1-6 (Fig. 1).
(3) Check for ignition feed at cluster wire harness
connector terminal J1-5. Repair as necessary.
NO TONE WHEN HEADLAMPS ARE ON AND
DRIVERS DOOR IS OPEN
(1) Check left door jamb switch for good ground
when drivers door is open.
(2) Check for ground at J2-5.
(3) Check for battery feed at cluster wire harness
connector terminal J1-6 (Fig. 1).
(4) Check for NO voltage at J1-5. Ignition voltage
must not be present for the chime to work.
(5) Check headlamp switch.
NO TONE WHEN KEY IS LEFT IN IGNITION
AND DRIVERS DOOR IS OPEN
(1) Check for continuity to ground at Pin 8 of the
J1 wire harness connector. If OK, go to Step 3. If not
OK, repair as necessary.(2) Using voltmeter, check for battery feed at Pin 6
of the J1 wire harness connector. Check for NO igni-
tion feed at Pin 5 of the J1 wire harness connector. If
OK, go to Step 3. If not OK, repair as necessary.
(3) Open driver's door and ensure the ignition key
is in the OFF or ACC position. Check for continuity
to ground at Pin 5 of the J2 wire harness connector.
If ground OK, replace cluster printed circuit board. If
no ground, check key-in switch or door switch wiring
and repair as necessary.
CHIMES CONTINUE WHEN HEADLAMPS ARE
TURNED OFF AND/OR KEY IS REMOVED
FROM IGNITION
Check for ground at J2-5. If grounded the chime
should activate. Make sure the door is closed, key is
in ignition and parking lamps are OFF. If ground is
still present check door switch, key in switch, head-
lamp switch and repair as necessary.
REMOVAL AND INSTALLATION
CHIME
The chime is built into the instrument cluster print
circuit board. Refer to Group 8E, Instrument Panel
and Gauges.
SEAT BELT BUCKLE
Refer to Group 23, Body of this service manual.
HEADLAMP SWITCH
Refer to Group 8E, Instrument Panel and Systems.
KEY-IN SWITCH
The Key-in switch is built into the ignition switch
assembly. Should the Key-in switch require service,
the ignition switch assembly must be replaced. Refer
to Group 8D Ignition System of this service manual.
Fig. 1 Cluster Wire Harness Connectors
8U - 2 CHIME WARNING/REMINDER SYSTEMPL
DIAGNOSIS AND TESTING (Continued)

8W-01 GENERAL INFORMATION
INDEX
page page
DESCRIPTION AND OPERATION
CIRCUIT FUNCTIONS..................... 4
CIRCUIT INFORMATION................... 4
CONNECTOR INFORMATION............... 7
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES.................... 8
INTRODUCTION......................... 1
NOTES, CAUTIONS, and WARNINGS......... 7
SECTION IDENTIFICATION................. 5
SPLICE LOCATIONS...................... 7
SYMBOLS.............................. 5
TAKE OUTS............................. 8
TERMINOLOGY.......................... 7
DIAGNOSIS AND TESTING
INTERMITTENT AND POOR CONNECTIONS.... 9TROUBLESHOOTING TESTS................ 9
TROUBLESHOOTING TOOLS............... 8
TROUBLESHOOTING WIRING PROBLEMS.... 10
SERVICE PROCEDURES
CONNECTOR AND TERMINAL REPLACEMENT . 12
CONNECTOR REPLACEMENT.............. 12
DIODE REPLACEMENT................... 14
TERMINAL REPLACEMENT................ 13
TERMINAL/CONNECTOR REPAIR-MOLEX
CONNECTORS........................ 10
TERMINAL/CONNECTOR REPAIRÐTHOMAS
AND BETTS CONNECTORS.............. 11
WIRING REPAIR........................ 10
SPECIAL TOOLS
WIRING/TERMINAL...................... 15
DESCRIPTION AND OPERATION
INTRODUCTION
Chrysler wiring diagrams are designed to provide
information regarding the vehicles wiring content. In
order to effectively use Chrysler wiring diagrams to
diagnose and repair a Chrysler vehicle, it is impor-
tant to understand all of their features and charac-
teristics.
Diagrams are arranged such that the power (B+)
side of the circuit is placed near the top of the page,
and the ground (B-) side of the circuit is placed near
the bottom of the page.
All switches, components, and modules are shown
in the at rest position with the doors closed and the
key removed from the ignition.Components are shown two ways. A solid line
around a component indicates that the component is
complete. A dashed line around a component indi-
cates that the component being shown is not com-
plete. Incomplete components have a reference
number to indicate the page where the component is
shown complete.
It is important to realize that no attempt is made
on the diagrams to represent components and wiring
as they appear on the vehicle. For example, a short
piece of wire is treated the same as a long one. In
addition, switches and other components are shown
as simply as possible, with regard to function only.
PL8W - 01 GENERAL INFORMATION 8W - 01 - 1

8W-02 COMPONENT INDEX
Component Page
A/C Compressor Clutch..................8W-42
A/C Compressor Clutch Relay.............8W-42
A/C Cycling Switch.....................8W-42
A/C Heater Blower Motor................8W-42
A/C Heater Control.....................8W-42
A/C Pressure Switches...................8W-42
ABS Warning Lamp Relay................8W-35
Airbag Control Module...................8W-43
Airbags..............................8W-43
Antenna..............................8W-47
Ash Receiver Lamp.....................8W-44
Automatic Shut Down Relay..............8W-30
Back-Up Lamp Switch...................8W-51
Back-Up Lamps........................8W-51
Battery..............................8W-20
Battery Temperature Sensor..............8W-30
Blower Motor Resistor Block..............8W-42
Brake Warning Lamp Switch...........8W-40, 50
Camshaft Position Sensor................8W-30
Center High Mounted Stop Lamp..........8W-51
Cigar Lighter Relay.....................8W-41
Cigar Lighter/Power Outlet...............8W-41
Circuit Breakers.......................8W-11
Clockspring.....................8W-30, 41, 61
Clutch Pedal Position Switch...........8W-10, 21
Combination Flasher....................8W-52
Controller Anti-Lock Brake...............8W-35
Crankshaft Position Sensor...............8W-30
Data Link Connector....................8W-30
Daytime Running Lamp Module...........8W-50
Diode No. 1........................8W-15, 42
Diode No. 2......................8W-10, 11, 44
Diode No. 3......................8W-11,44,70
Dome Lamp...........................8W-44
Door Ajar Switches.....................8W-44
Door Jamb Switches....................8W-44
Door Lock Motors......................8W-61
Door Lock Motors......................8W-61
Door Lock Switches.....................8W-61
Duty Cycle Evap/Purge Solenoid...........8W-30
EGR Transducer Solenoid................8W-30
Engine Coolant Temperature Sensor........8W-30
Engine Oil Pressure Switch...............8W-40
Engine Starter Motor....................8W-21
Engine Starter Motor Relay...............8W-21
Fog Lamp Relays....................8W-50, 51
Fog Lamp Switches..................8W-50, 51
Fog Lamps.........................8W-50, 51
Fuel Injectors..........................8W-30
Fuel Pump Module.....................8W-30
Fuel Pump Relay.......................8W-30
Fuse Block............................8W-11Component Page
Fuses (FB)............................8W-11
Fuses (PDC)...........................8W-10
Fusible Link........................8W-20, 21
Generator.............................8W-20
Glove Box Lamp And Switch..............8W-44
Grounds..............................8W-15
Halo Lamp............................8W-44
Headlamp Dimmer And Optical Horn Switch .8W-50
Headlamp Leveling Motors...............8W-50
Headlamp Leveling Switch...............8W-50
Headlamp Switch.......................8W-50
Headlamps............................8W-50
High Speed Warning Module..............8W-40
Horn Relay...........................8W-41
Horn Switches.........................8W-41
Horns................................8W-41
IAT/Map Sensor........................8W-30
Idle Air Control Motor...................8W-30
Ignition Coil Pack......................8W-30
Ignition Switch........................8W-10
Illumination Lamps.....................8W-40
Immobilizer...........................8W-61
Immobilizer Engine Sensor............8W-30, 61
Indicator Lamps........................8W-40
Instrument Cluster.....................8W-40
Intermittent Wipe/Wash Switch............8W-53
Key-In Switch.........................8W-40
Knock Sensor..........................8W-30
License Lamps.........................8W-51
Map/Reading Lamps....................8W-44
Noise Supressor.....................8W-10, 30
Oxygen Sensors........................8W-30
Park Brake Switch...................8W-40, 50
Park/Neutral Position Switch...........8W-30, 51
Park/Turn Signal Lamps..............8W-50, 52
Power Distribution Center................8W-10
Power Folding Mirror Relay...............8W-62
Power Mirror Fuse Holder................8W-62
Power Mirrors.........................8W-62
Power Steering Pressure Switch...........8W-30
Power Sunroof Motor....................8W-64
Power Window Motors...................8W-60
Power Window Switches.................8W-60
Powertrain Control Module...............8W-30
PRNDL Lamp.........................8W-44
Radiator Fan Motor.....................8W-42
Radio................................8W-47
Rear Window Defogger..................8W-48
Rear Window Defogger Switch.............8W-48
Remote Keyless Entry Module.............8W-61
Remote Keyless Entry Program
Module Connector....................8W-61
PL8W - 02 COMPONENT INDEX 8W - 02 - 1

8W-11 FUSE BLOCK
Component Page
A/C Compressor Clutch Relay...........8W-11-14
A/C Cycling Switch................8W-11-12, 13
A/C Heater Blower Motor...........8W-11-12, 13
A/C Heater Control.............8W-11-17, 18, 19
ABS Warning Lamp Relay.............8W-11-14
Airbag Control Module..........8W-11-12, 13, 14
Ash Receiver Lamp.............8W-11-17, 18, 19
Back-Up Lamp Switch..............8W-11-12, 13
Cigar Lighter Relay.................8W-11-9, 20
Cigar Lighter/Power Outlet..........8W-11-7, 8, 9
Circuit Breaker.............8W-11-15, 16, 21, 22
Circuit Breaker (FB)..................8W-11-16
Controller Anti-Lock Brake.............8W-11-14
Daytime Running Lamp Module.........8W-11-15
Diode No.2.........................8W-11-23
Diode No.3.........................8W-11-23
Driver Door Lock Switch...............8W-11-11
Driver Power Window Switch........8W-11-15, 16
Duty Cycle Evap/Purge Solenoid.........8W-11-14
EGR Transducer Solenoid..............8W-11-14
Fog Lamp Switch..................8W-11-11,17
Front Fog Lamp Switch..............8W-11-8, 9
Fuel Pump Relay.....................8W-11-14
Fuse 1 (FB)......................8W-11-7, 8, 9
Fuse 2 (FB)......................8W-11-7, 8, 9
Fuse 3 (FB).........................8W-11-11
Fuse 4 (FB).........................8W-11-11
Fuse 5 (FB)......................8W-11-12, 13
Fuse 6 (FB)......................8W-11-12, 13
Fuse 7 (FB)......................8W-11-12, 13
Fuse 8 (FB)......................8W-11-12, 13
Fuse 9 (FB)....................8W-11-9, 14, 19
Fuse 10 (FB)........................8W-11-14
Fuse 11 (FB).....................8W-11-15, 16
Fuse 12 (FB)..............8W-11-7, 8, 14, 17, 18
Fuse 13 (PDC).......................8W-11-23
Fuse 14 (FB)........................8W-11-20
Fuse 15 (FB)........................8W-11-20
Fuse 16 (FB)........................8W-11-20
Fuse 17 (FB).....................8W-11-21, 22
Fuse 18 (FB).....................8W-11-21, 22
Fuse Block...........8W-11-2, 3, 4, 7, 8, 9, 11, 12,
13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23
Halo Lamp.........................8W-11-23
Headlamp Dimmer And Optical
Horn Switch...................8W-11-21, 22Component Page
Headlamp Leveling Switch.......8W-11-18, 19, 22
Headlamp Switch . .8W-11-7, 8, 9, 17, 18, 19, 21, 22,
High Speed Warning Module.........8W-11-12, 13
Immobilizer......................8W-11-11,16
Instrument Cluster.....8W-11-15, 16, 17, 18, 19, 23
Intermittent Wipe/Wash Switch.........8W-11-20
Left Front Door Jamb Switch...........8W-11-23
Left Front Side Marker Lamp...........8W-11-10
Left Headlamp....................8W-11-21, 22
Left Headlamp Leveling Motor..........8W-11-22
Left License Lamp..................8W-11-8, 9
Left Park/Turn Signal Lamp............8W-11-10
Left Tail/Stop Lamp.................8W-11-8, 9
Left Tail/Stop/Turn Signal Lamp..........8W-11-7
License Lamp........................8W-11-7
Map/Reading Lamps..................8W-11-23
Park/Neutral Position Switch........8W-11-12, 13
Passenger Door Lock Switch............8W-11-11
Passenger Power Window Switch.....8W-11-15, 16
Power Distribution Center...........8W-11-14, 23
Power Mirror Fuse Holder.............8W-11-16
Powertrain Control Module.............8W-11-14
PRNDL Lamp.................8W-11-17, 18, 19
Radio...............8W-11-7, 8, 9, 17, 18, 19, 20
Rear Fog Lamp Switch..........8W-11-18, 19, 22
Rear Window Defogger
Switch...............8W-11-12, 13, 17, 18, 19
Remote Keyless Entry Module......8W-11-7, 11, 15
Right Front Side Marker Lamp..........8W-11-10
Right Headlamp..................8W-11-21, 22
Right Headlamp Leveling Motor.........8W-11-22
Right License Lamp.................8W-11-8, 9
Right Park/Turn Signal Lamp...........8W-11-10
Right Tail/Stop Lamp................8W-11-8, 9
Right Tail/Stop/Turn Signal Lamp........8W-11-7
Sunroof Slide Switch..................8W-11-20
Sunroof Vent Switch..................8W-11-20
Time Delay Relay....................8W-11-23
Time Out Relay......................8W-11-23
Torque Converter Clutch Solenoid........8W-11-14
Turn Signal/Hazard Switch..........8W-11-12, 13
Vapor Canister Leak Detector...........8W-11-14
Wipe/Wash Switch....................8W-11-20
Wiper Motor........................8W-11-20
PL8W - 11 FUSE BLOCK 8W - 11 - 1

C3C2M50 20YL/RD
C1
TIME DELAY RELAY (C) (LHD)
FUNCTION CIRCUIT CAVITY
M1 20PK
M23 22YL/BKKEY-IN LAMP DRIVER
FUSED B+
TIME DELAY RELAY OUTPUT COMBINATION FLASHER INPUT L55 20BK/YL
B1
FUNCTION CIRCUIT CAVITYCOMBINATION FLASHER (B) (LHD)
B2L32 20PK COMBINATION FLASHER OUTPUT
GROUND Z2 20BK/LG
B3
FEED TO CIGAR LIGHTER RELAY
CIGAR LIGHTER FEED FUSE BLOCK F13 18DB
F30 18RD
B5 B3CIGAR LIGHTER FEED F30 16RD
B2GROUND Z1 20BK
B1
CIGAR LIGHTER RELAY (B) (RHD)
FUNCTION CIRCUIT CAVITY
-
CAVITY CIRCUIT FUNCTION
NOT USED (C) (RHD)
C1-
C2
C3--
--
8W - 11 - 6 8W-11 FUSE/FUSE BLOCKPL
J988W-18212

1FUSE15A
21
BATT A3
F30
16
RD
2FUSE15A
22
F33
20
PK/RD
HEADLAMP
SWITCH
4
L7
20
BK/YLL7
20
BK/YL
S218
L7
20
BK/YL
7C230
L7
20
BK/YL
4
RADIO
54
RADIO
L7
20
BK/YLL7
20
BK/YL
MODULE ENTRY
KEYLESS
REMOTE
L7
20
BK/YL
L7
18
BK/YL
222
LAMP LICENSE
L7
18
BK/YLL7
20
BK/YL
S306
L7
20
BK/YL
1
FUSE
BLOCK12
32
4A
FUSE
12
RKE
OTHER
E1
20
TN
9
2
1 0
FUSE
BLOCK
TO
C105 OUTLET POWER
LIGHTER/
CIGAR
C2C2
0 OFF
1 PARK
2 HEAD 1
1
2
C2
LAMP SIGNAL
TURN
STOP/
TAIL/
LEFT RIGHT
TAIL/
STOP/
TURN
SIGNAL
LAMP
A
(8W-11-10) (8W-41-4)(8W-11-2)
(8W-11-17)(8W-11-2)
(8W-51-5) (8W-61-7)(8W-47-2)(8W-47-2) (8W-10-8)
(8W-50-2)
(8W-50-9)
(8W-50-10)
(8W-51-5) (8W-51-5)
PL8W-11 FUSE/FUSE BLOCK
EXCEPT BUILT-UP-EXPORT8W - 11 - 7
8213J988W-1

FUSE
BLOCK
BATT A3
S214
24RD/YL16 F35
3SWITCH LOCK
DOOR
DRIVER PASSENGER
DOOR
LOCK
SWITCH
3
F35
16
RD/YL
F35
18
RD/YL
RD/YL18 F35 RD/YL16 F35
RD/YL16 F3524
23
10A
FUSE
4
20AFUSE
3
34
LHD RHD
1C231 C20511C231 C2051
RHD LHD
F35
16
RD/YL
REMOTE
KEYLESS
ENTRY
MODULE
2C1
RD/YL16 F35
F61
20
WT/OR
2
(EXCEPT BUILT-UP-EXPORT) SWITCH
LAMP
FOG
BUILT-UP-EXPORTEXCEPT
BUILT-UP-EXPORT
IMMOBILIZER
10C242
F35
16
RD/YL
(8W-10-8)
(8W-61-2)
(8W-61-10)
(8W-61-11) (8W-61-4)
(8W-61-10)
(8W-61-11)(8W-11-2)
(8W-11-3)
(8W-11-4)
(8W-61-6) (8W-50-12)
(8W-61-8)
PL8W-11 FUSE/FUSE BLOCK 8W - 11 - 11
8217J988W-1

11FUSE5A
31
BLOCK
FUSE
G5
20
DB/WT
ST-RUN A21
5
G5
20
DB/WT
G5
20
DB/WT
G5
20
DB/WT
5
CLUSTER INSTRUMENT
85
G5
20
DB/WTG5
20
DB/WT
S219
MODULE LAMP
RUNNING
DAYTIME DAYTIME
RUNNING
LAMP
MODULE MODULEENTRY
KEYLESS
REMOTE
OTHER
C1 C1
RKE
11
CIRCUIT
BREAKER
30A
41
42
3
4
SWITCH WINDOW
POWER
PASSENGER
SWITCH WINDOW
POWER
DRIVER
F21
14
TN
F21
14
TN
F21
14
TN
F21
14
TN
7C231C2057
RUN A22
(8W-40-6)
(8W-50-14) (8W-50-14) (8W-61-6)(8W-10-9)
(8W-11-2)
(8W-60-2) (8W-60-2)(8W-10-8)
PL8W-11 FUSE/FUSE BLOCK
EXCEPT BUILT-UP-EXPORT8W - 11 - 15
8221J988W-1