fuses DODGE RAM 2002 Service Owner's Manual

²Glove Box- The hinged bin-type glove box in
the passenger side of the instrument panel features a
recessed paddle-operated latch handle. Three molded
hook formations on the lower edge of the glove box
door are engaged with and pivot on three hinge pins
integral to the lower edge of the instrument panel
support structure. The glove box door also serves as
the passenger side knee blocker. A honeycomb struc-
ture between the inner and outer glove box door pan-
els helps to absorb the impact load and distribute it
to the instrument panel structure.
²Steering Column Opening Cover- The steer-
ing column opening cover serves as the driver side
knee blocker. This molded plastic cover has an inte-
gral ribbed plastic liner concealed behind it, for
increased strength and integrity. The steering column
opening cover transfers impact loads to the instru-
ment panel structural support.
²Top Cover- The instrument panel top cover or
base trim is the molded, grained, and color impreg-
nated plastic outer skin of the instrument panel
structural support.
Hard wired circuitry connects the electrical compo-
nents on the instrument panel to each other through
the electrical system of the vehicle. These hard wired
circuits are integral to several wire harnesses, which
are routed throughout the vehicle and retained by
many different methods. These circuits may be con-
nected to each other, to the vehicle electrical system
and to the instrument panel components through the
use of a combination of soldered splices, splice block
connectors and many different types of wire harness
terminal connectors and insulators. Refer to the
appropriate wiring information. The wiring informa-
tion includes complete circuit diagrams, proper wire
and connector repair procedures, further details on
wire harness routing and retention, as well as pin-
out and location views for the various wire harness
connectors, splices, and grounds.
OPERATION
The instrument panel serves as the command cen-
ter of the vehicle, which necessarily makes it a very
complex unit. The instrument panel is designed to
house the controls and monitors for standard and
optional powertrains, climate control systems, audio
systems, safety systems, and many other comfort or
convenience items. When the components of the
instrument panel structural support are properly
assembled and secured in the vehicle they provide
superior instrument panel stiffness and integrity to
help reduce buzzes, squeaks, and rattles. This type of
construction also provides improved energy absorp-
tion which, in conjunction with the dual airbags and
seat belts, helps to improve occupant protection.The instrument panel is also designed so that all of
the various controls can be safely reached and the
monitors can be easily viewed by the vehicle operator
when driving, while still allowing relative ease of
access to each of these items for service. Modular
instrument panel construction allows all of the
gauges and controls to be serviced from the front of
the panel. In addition, most of the instrument panel
electrical components can be accessed without com-
plete instrument panel removal. However, if neces-
sary, the instrument panel can be removed from the
vehicle as an assembly.
The steering column opening cover with its inte-
gral knee blocker located on the driver side of the
instrument panel works in conjunction with the air-
bag system in a frontal vehicle impact to keep the
driver properly positioned for an airbag deployment.
In addition, removal of this component provides
access to the steering column mounts, the steering
column wiring, the Junction Block (JB) (removal of a
snap-fit fuse access panel on the left end of the
instrument panel allows access to the fuses and cir-
cuit breakers), the Central Timer Module (CTM), the
Infinity speaker filter choke and relay unit, much of
the instrument panel wiring, and the gear selector
indicator cable (automatic transmission).
In a frontal collision, the glove box door on the pas-
senger side of the instrument panel provides the
same function for the front seat passenger as the
knee blocker does for the driver. The glove box door
also incorporates a recessed latch handle. Removal of
the glove box provides access to the passenger airbag,
the glove box lamp and switch, the radio antenna
coaxial cable, the heating and air conditioning vac-
uum harness connector, and additional instrument
panel wiring.
Removal of the instrument panel cluster bezel
allows access to the headlamp switch, instrument
cluster, radio, passenger airbag on-off switch, heated
seat switches (if equipped), and the heating and air
conditioning control. Removal of the instrument clus-
ter allows access to the cluster illumination and indi-
cator bulbs, and more of the instrument panel
wiring. Complete instrument panel removal is
required for service of most components internal to
the heating and air conditioning system housing,
including the heater core and the evaporator.
See the owner's manual in the vehicle glove box for
more information on the features, use and operation
of all of the components and systems mounted on or
in the instrument panel.
23 - 106 INSTRUMENT PANEL SYSTEMBR/BE
INSTRUMENT PANEL SYSTEM (Continued)

A/C Diagnosis
Condition Possible Causes Correction
2. Faulty a/c low
pressure switch.2. (Refer to Controls/A/C Low Pressure Switch/Diagnosis
and Testing) in this group. Test the a/c low pressure
switch and replace, if required.
3. Faulty Powertrain
Control Module (PCM).3. (Refer to Appropriate Diagnostic Information) for testing
the PCM. Test the PCM and replace, if required.
EQUAL PRESSURES,
BUT THE
COMPRESSOR CLUTCH
DOES NOT ENGAGE.1. No refrigerant in the
refrigerant system.1. (Refer to Plumbing/Diagnosis and Testing - Refrigerant
System Leaks) in this group. Test the refrigerant system
for leaks. Repair, evacuate and charge the refrigerant
system, if required.
2. Faulty fuse. 2. Check the fuses in the Power Distribution Center and
the junction block. Repair the shorted circuit or
component and replace the fuses, if required.
3. Faulty a/c compressor
clutch coil.3. (Refer to Controls/A/C Compressor Clutch Coil/
Diagnosis and Testing) in this group. Test the compressor
clutch coil and replace, if required.
4. Faulty a/c compressor
clutch relay.4. (Refer to Controls/A/C Compressor Clutch Relay/
Diagnosis and Testing) in this group. Test the compressor
clutch relay and relay circuits. Repair the circuits or
replace the relay, if required.
5. Improperly installed or
faulty a/c low pressure
switch.5. (Refer to Controls/A/C Low Pressure Switch/Diagnosis
and Testing) in this group. Test the a/c low pressure
switch and tighten or replace, if required.
6. Faulty a/c high
pressure switch.6. (Refer to Controls/A/C High Pressure Switch/Diagnosis
and Testing) in this group. Test the a/c high pressure
switch and replace, if required.
7. Faulty Powertrain
Control Module (PCM).7. (Refer to Appropriate Diagnostic Information) for testing
the PCM. Test the PCM and replace, if required.
8. Faulty a/c heater
control.8. (Refer to Controls/A/C Heater Control/Diagnosis and
Testing) in this group. Test the a/c heater control and
replace, if required.
NORMAL PRESSURES,
BUT A/C
PERFORMANCE TEST
AIR TEMPERATURES AT
CENTER PANEL
OUTLET ARE TOO
HIGH.1. Excessive refrigerant
oil in system.1. (Refer to Plumbing/Refrigerant Oil/Standard Procedure
- Refrigerant Oil Level) in this group. Recover the
refrigerant from the refrigerant system and inspect the
refrigerant oil content. Restore the refrigerant oil to the
proper level, if required.
2. Blend door actuator
inoperative or faulty.2. Check the Blend Door Actuator operation. Replace as
required.
3. Blend door
inoperative, obstructed or
sealing improperly.3. (Refer to Distribution/Blend Door/Removal/Installation)
in this group. Inspect the blend door for proper operation
and sealing and correct, if required.
LOW SIDE PRESSURE
IS NORMAL OR
SLIGHTLY LOW, AND
HIGH SIDE PRESSURE
IS TOO LOW.1. Low refrigerant system
charge.1. (Refer to Plumbing/Diagnosis and Testing - Refrigerant
System Leaks) in this group. Test the refrigerant system
for leaks. Repair, evacuate and charge the refrigerant
system, if required.
24 - 4 HEATING & AIR CONDITIONINGBR/BE
HEATING & AIR CONDITIONING (Continued)

OPERATION
The compressor clutch assembly provides the
means to engage and disengage the compressor from
the engine serpentine accessory drive belt. When the
clutch coil is energized, it magnetically draws the
clutch into contact with the pulley and drives the
compressor shaft. When the coil is not energized, the
pulley freewheels on the clutch hub bearing, which is
part of the pulley. The compressor clutch and coil are
the only serviced parts on the compressor.
The compressor clutch engagement is controlled by
several components: the a/c heater mode control
switch, the a/c loss of charge switch, the a/c pressure
transducer, the compressor clutch relay, the evapora-
tor temperature sensor and the Powertrain Control
Module (PCM). The PCM may delay compressor
clutch engagement for up to thirty seconds(Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MOD-
ULES/POWERTRAIN CONTROL MODULE -
DESCRIPTION).
DIAGNOSIS AND TESTING - A/C COMPRESSOR
CLUTCH COIL
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). The battery must
be fully-charged before performing the following
tests. Refer to Battery for more information.
(1) Connect an ammeter (0 to 10 ampere scale) in
series with the clutch coil terminal. Use a voltmeter
(0 to 20 volt scale) with clip-type leads for measuring
the voltage across the battery and the compressor
clutch coil.(2) With the a/c heater mode control switch in any
A/C mode, and the blower motor switch in the lowest
speed position, start the engine and run it at normal
idle.
(3) The compressor clutch coil voltage should read
within 0.2 volts of the battery voltage. If there is
voltage at the clutch coil, but the reading is not
within 0.2 volts of the battery voltage, test the clutch
coil feed circuit for excessive voltage drop and repair
as required. If there is no voltage reading at the
clutch coil, use a DRB IIItscan tool and (Refer to
Appropriate Diagnostic Information) for testing of the
compressor clutch circuit. The following components
must be checked and repaired as required before you
can complete testing of the clutch coil:
²Fuses in the junction block and the Power Dis-
tribution Center (PDC)
²A/C Heater mode control switch
²Compressor clutch relay
²A/C High Pressure Switch
²A/C Low Pressure Switch
²Powertrain Control Module (PCM).
(4) The compressor clutch coil is acceptable if the
current draw measured at the clutch coil is 2.0 to 3.9
amperes with the electrical system voltage at 11.5 to
12.5 volts. This should only be checked with the work
area temperature at 21É C (70É F). If system voltage
is more than 12.5 volts, add electrical loads by turn-
ing on electrical accessories until the system voltage
drops below 12.5 volts.
(a) If the clutch coil current reading is four
amperes or more, the coil is shorted and should be
replaced.
(b) If the clutch coil current reading is zero, the
coil is open and should be replaced.
STANDARD PROCEDURE - A/C COMPRESSOR
CLUTCH BREAK-IN
After a new compressor clutch has been installed,
cycle the compressor clutch approximately twenty
times (five seconds on, then five seconds off). During
this procedure, set the A/C Heater control to the
Recirculation Mode, the blower motor switch in the
highest speed position, and the engine speed at 1500
to 2000 rpm. This procedure (burnishing) will seat
the opposing friction surfaces and provide a higher
compressor clutch torque capability.
REMOVAL
The refrigerant system can remain fully-charged
during compressor clutch, pulley, or coil replacement.
The compressor clutch can be serviced in the vehicle.
(1) Disconnect and isolate the battery negative
cable.
(2) On models with the diesel engine option,
remove the compressor from the engine. Do not
Fig. 4 COMPRESSOR CLUTCH - TYPICAL
1 - CLUTCH PLATE
2 - SHAFT KEY
3 - PULLEY
4 - COIL
5 - CLUTCH SHIMS
6 - SNAP RING
7 - SNAP RING
BR/BECONTROLS 24 - 13
A/C COMPRESSOR CLUTCH (Continued)

FUEL INJECTION PUMP RELAY -
DESCRIPTION......................14-103
FUEL INJECTION PUMP RELAY -
OPERATION........................14-103
FUEL INJECTION PUMP TIMING -
DIAGNOSIS AND TESTING.............14-70
FUEL INJECTION SYSTEM -
DESCRIPTION, DIESEL................14-91
FUEL INJECTOR - DESCRIPTION....14-52,14-97
FUEL INJECTOR - DIAGNOSIS AND
TESTING...........................14-53
FUEL INJECTOR - INSTALLATION.......14-102
FUEL INJECTOR - OPERATION..........14-98
FUEL INJECTOR - REMOVAL...........14-101
FUEL INJECTOR FIRING ORDER, DIESEL . . 14-62
FUEL INJECTOR TEST - DIAGNOSIS AND
TESTING...........................14-99
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION...................14-7,14-77
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION........................14-8
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION.....................14-7,14-77
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-7
FUEL LINE LEAKS - DIAGNOSIS AND
TESTING, HIGH-PRESSURE.............14-78
FUEL LINES - DESCRIPTION.............14-8
FUEL LINES - DESCRIPTION, HIGH
PRESSURE.........................14-78
FUEL LINES - OPERATION, HIGH
PRESSURE...........................14-78
FUEL PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING..............14-2
FUEL PUMP - DESCRIPTION.............14-9
FUEL PUMP - OPERATION..............14-9
FUEL PUMP 235 H.P. - DESCRIPTION....14-69
FUEL PUMP 245 H.P. - DESCRIPTION....14-69
FUEL PUMP AMPERAGE TEST -
DIAGNOSIS AND TESTING.............14-10
FUEL PUMP CAPACITY TEST -
DIAGNOSIS AND TESTING..............14-9
FUEL PUMP MODULE - DESCRIPTION....14-12
FUEL PUMP MODULE - INSTALLATION . . . 14-13
FUEL PUMP MODULE - OPERATION......14-13
FUEL PUMP MODULE - REMOVAL.......14-13
FUEL PUMP PRESSURE TEST -
DIAGNOSIS AND TESTING..............14-9
FUEL PUMP RELAY - DESCRIPTION......14-40
FUEL PUMP RELAY - INSTALLATION.....14-40
FUEL PUMP RELAY - OPERATION........14-40
FUEL PUMP RELAY - REMOVAL.........14-40
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-4
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-3
FUEL REQUIREMENTS - GAS ENGINES -
DESCRIPTION.........................0-2
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-89
FUEL SENSOR - OPERATION, WATER IN . . 14-89
FUEL SENSOR - REMOVAL, WATER IN....14-89
FUEL SUPPLY RESTRICTIONS -
DIAGNOSIS AND TESTING.............14-60
FUEL SYSTEM - DIAGNOSIS AND
TESTING, AIR IN.....................14-60
FUEL SYSTEM AIR LEAK VACUUM TEST
- DIAGNOSIS AND TESTING............14-57
FUEL SYSTEM PARTS - STANDARD
PROCEDURES, CLEANING..............14-61
FUEL SYSTEM PRESSURE - GAS
ENGINES - SPECIFICATIONS.............14-3
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-3
FUEL SYSTEM PRESSURES, DIESEL
ENGINES...........................14-62
FUEL SYSTEM, SPECIAL TOOLS.....14-35,14-4
FUEL SYSTEM, SPECIAL TOOLS -
DIESEL............................14-63
FUEL TANK - DESCRIPTION............14-18
FUEL TANK - DESCRIPTION, DIESEL.....14-82
FUEL TANK - INSTALLATION
............14-20
FUEL TANK - OPERATION
..............14-18
FUEL TANK - REMOVAL
...............14-18
FUEL TANK CHECK VALVE -
DESCRIPTION
.......................14-21
FUEL TANK CHECK VALVE -
INSTALLATION
.......................14-23FUEL TANK CHECK VALVE - REMOVAL....14-22
FUEL TANK MODULE - DESCRIPTION.....14-82
FUEL TANK MODULE - INSTALLATION....14-83
FUEL TANK MODULE - OPERATION......14-82
FUEL TANK MODULE - REMOVAL........14-83
FUEL TEMPERATURE SENSOR -
DESCRIPTION......................14-104
FUEL TEMPERATURE SENSOR -
OPERATION........................14-104
FUEL TRANSFER PUMP - DESCRIPTION . . 14-83
FUEL TRANSFER PUMP - INSTALLATION . . 14-87
FUEL TRANSFER PUMP - OPERATION....14-83
FUEL TRANSFER PUMP - REMOVAL......14-86
FUEL TRANSFER PUMP PRESSURE -
DIAGNOSIS AND TESTING.............14-84
FUSE - DESCRIPTION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - DESCRIPTION, IOD...........8W-97-5
FUSE - INSTALLATION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - INSTALLATION, IOD..........8W-97-6
FUSE - OPERATION, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - OPERATION, IOD.............8W-97-5
FUSE - REMOVAL, GENERATOR
CARTRIDGE.......................8W-97-4
FUSE - REMOVAL, IOD..............8W-97-6
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.........8W-01-9
GAP AND FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY...............23-56
GASKET - DESCRIPTION, CYLINDER
HEAD COVER.........................9-20
GASKET - OPERATION, CYLINDER HEAD
COVER..............................9-21
GASKET FAILURE - DIAGNOSIS AND
TESTING, CYLINDER HEAD..........9-21,9-76
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE . . 9-10,9-122,9-66
GASOLINE ENGINE - INSTALLATION......19-37
GASOLINE ENGINE - NEGATIVE CABLE
INSTALLATION.......................8F-22
GASOLINE ENGINE - NEGATIVE CABLE
REMOVAL..........................8F-22
GASOLINE ENGINE - POSITIVE CABLE
INSTALLATION.......................8F-22
GASOLINE ENGINE - POSITIVE CABLE
REMOVAL..........................8F-21
GASOLINE ENGINE - REMOVAL.........19-35
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE......................8J-18
GAUGE - DESCRIPTION, FUEL...........8J-19
GAUGE - DESCRIPTION, OIL PRESSURE . . 8J-25
GAUGE - DESCRIPTION, VOLTAGE.......8J-33
GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-19
GAUGE - OPERATION, FUEL............8J-20
GAUGE - OPERATION, OIL PRESSURE....8J-25
GAUGE - OPERATION, VOLTAGE.........8J-33
GAUGE SENDING UNIT - DIAGNOSIS
AND TESTING, FUEL...................14-7
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-8
GAUGES INDICATOR - DESCRIPTION,
CHECK.............................8J-17
GAUGES INDICATOR - OPERATION,
CHECK.............................8J-17
GEAR - ADJUSTMENTS................19-18
GEAR - DESCRIPTION.................19-16
GEAR - INSTALLATION................19-18
GEAR - INSTALLATION, PINION
GEAR/RING..........................3-43
GEAR - OPERATION...................19-16
GEAR - REMOVAL....................19-18
GEAR - REMOVAL, PINION GEAR/RING....3-41
GEAR HOUSING - INSTALLATION........9-188
GEAR HOUSING - REMOVAL............9-187
GEAR HOUSING COVER - INSTALLATION . . 9-190
GEAR HOUSING COVER - REMOVAL
.....9-189
GEAR HOUSING PLUG - INSTALLATION,
STEERING
..........................19-30
GEAR HOUSING PLUG - REMOVAL,
STEERING
..........................19-29
GEAR LEAKAGE - DIAGNOSIS AND
TESTING, POWER STEERING
...........19-16
GEAR SELECTOR INDICATOR -
DESCRIPTION
.......................8J-20GEAR SELECTOR INDICATOR -
OPERATION.........................8J-21
GEAR SHIFT LEVER - INSTALLATION.....19-15
GEAR SHIFT LEVER - REMOVAL.........19-14
GEAR, SPECIAL TOOLS - POWER
STEERING..........................19-22
GEAR, SPECIFICATIONS - POWER
STEERING..........................19-21
GEAR/RING GEAR - INSTALLATION,
PINION.............................3-43
GEAR/RING GEAR - REMOVAL, PINION....3-41
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION.......3-104,3-132,3-75
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION..........3-103,3-131,3-73
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING..........3-104,3-132,3-75
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING................3-103,3-131,3-73
GEARTRAIN/OUTPUT SHAFT -
ASSEMBLY, PLANETARY........21-199,21-371
GEARTRAIN/OUTPUT SHAFT -
DESCRIPTION, PLANETARY......21-197,21-369
GEARTRAIN/OUTPUT SHAFT -
DISASSEMBLY, PLANETARY.....21-198,21-369
GEARTRAIN/OUTPUT SHAFT -
INSPECTION, PLANETARY.......21-199,21-371
GEARTRAIN/OUTPUT SHAFT -
OPERATION, PLANETARY.......21-197,21-369
GENERAL - WARNINGS.............8W-01-7
GENERATOR - DESCRIPTION...........8F-28
GENERATOR - INSTALLATION............8F-30
GENERATOR - OPERATION.............8F-28
GENERATOR - REMOVAL...............8F-28
GENERATOR CARTRIDGE FUSE -
DESCRIPTION.....................8W-97-4
GENERATOR CARTRIDGE FUSE -
INSTALLATION....................8W-97-4
GENERATOR CARTRIDGE FUSE -
OPERATION.......................8W-97-4
GENERATOR CARTRIDGE FUSE -
REMOVAL........................8W-97-4
GENERATOR RATINGS, SPECIFICATIONS . . 8F-26
GENERATOR/CHARGING SYSTEM -
SPECIFICATIONS, TORQUE.............8F-27
GLASS - DESCRIPTION, STATIONARY....23-145
GLASS - INSTALLATION, BACKLITE VENT . 23-146
GLASS - INSTALLATION, DOOR.........23-70
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-98
GLASS - OPERATION, STATIONARY.....23-145
GLASS - REMOVAL, BACKLITE VENT....23-146
GLASS - REMOVAL, DOOR.............23-70
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-98
GLASS RUN CHANNEL - INSTALLATION . . . 23-71
GLASS RUN CHANNEL - REMOVAL......23-71
GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-153
GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-152
GLOVE BOX - ASSEMBLY.............23-111
GLOVE BOX - DISASSEMBLY..........23-110
GLOVE BOX LAMP AND SWITCH -
INSTALLATION.......................8L-36
GLOVE BOX LAMP AND SWITCH -
REMOVAL
..........................8L-35
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-112
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-111
GLOVE BOX OPENING UPPER TRIM -
INSTALLATION
......................23-112
GLOVE BOX OPENING UPPER TRIM -
REMOVAL
.........................23-112
GOVERNOR - DESCRIPTION,
ELECTRONIC
.................21-152,21-322
GOVERNOR - INSTALLATION,
ELECTRONIC
.................21-154,21-324
GOVERNOR - OPERATION, ELECTRONIC
. 21-153,
21-323
GOVERNOR - REMOVAL, ELECTRONIC
. . 21-154,
21-324
GRAB HANDLE - INSTALLATION,
A-PILLAR
..........................23-119
GRAB HANDLE - REMOVAL, A-PILLAR
. . . 23-119
GRADING - STANDARD PROCEDURE,
PISTON
............................9-166
GRID - DESCRIPTION, HEATED MIRROR
. . . 8G-4
14 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-44
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-78
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-179
LINES - DESCRIPTION, FUEL............14-8
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-78
LINES - DESCRIPTION, REFRIGERANT....24-40
LINES - DESCRIPTION, VACUUM........25-37
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-78
LINES - OPERATION, REFRIGERANT......24-41
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-40
LINKAGE - 2WD - INSTALLATION........19-41
LINKAGE - 2WD - REMOVAL............19-40
LINKAGE - 4WD - DESCRIPTION........19-42
LINKAGE - 4WD - INSTALLATION........19-43
LINKAGE - 4WD - REMOVAL............19-42
LINKAGE - INSTALLATION...............6-16
LINKAGE - REMOVAL..................6-15
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-41,
19-44
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-12
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-5
LOCK - STANDARD PROCEDURE,
HYDROSTATIC...............9-11,9-122,9-66
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY.....19-9
LOCK CYLINDER - INSTALLATION.......23-74
LOCK CYLINDER - INSTALLATION.......19-10
LOCK CYLINDER - REMOVAL...........23-74
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, POWER....8N-7
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-7
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER.............8N-6
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCKS - OPERATION, POWER
...........8N-3
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING
......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING
......................8O-29
LOOP HGT ADJUSTER KNOB -
INSTALLATION, TURNING
..............8O-30
LOOP HGT ADJUSTER KNOB -
REMOVAL, TURNING
.................8O-30LOW FUEL INDICATOR - DESCRIPTION . . . 8J-22
LOW FUEL INDICATOR - OPERATION.....8J-22
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C...................24-21
LOW PRESSURE SWITCH - OPERATION,
A/C................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C................................24-21
LOWER - INSTALLATION, LATCH........23-80
LOWER - INSTALLATION, LATCH
STRIKER...........................23-82
LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-1
LUBRICATION - DESCRIPTION....9-174,9-42,9-98
LUBRICATION - DESCRIPTION, AXLE.......0-5
LUBRICATION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-63,9-8
LUBRICATION - OPERATION....9-174,9-42,9-98
LUBRICATION - STANDARD PROCEDURE . 19-40,
19-42
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-18
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-19
LUMBAR CONTROL SWITCH - REMOVAL . 8N-19
LUMBAR MOTOR - DESCRIPTION.......8N-19
LUMBAR MOTOR - DIAGNOSIS AND
TESTING...........................8N-19
LUMBAR MOTOR - OPERATION.........8N-19
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-132
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-159
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT.............9-31
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT........................9-31
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT....................9-32,9-88
MAIN BEARINGS - OPERATION,
CRANKSHAFT........................9-31
MAIN BEARINGS - REMOVAL,
CRANKSHAFT....................9-31,9-88
MAIN BEARINGS - STANDARD
PROCEDURE, FITTING CRANKSHAFT......9-88
MAINTENANCE SCHEDULES -
DESCRIPTION.........................0-7
MALFUNCTION INDICATOR LAMP MIL -
DESCRIPTION.......................8J-23
MALFUNCTION INDICATOR LAMP MIL -
OPERATION.........................8J-23
MANAGER - DESCRIPTION, TASK........25-17
MANAGER - OPERATION, TASK.........25-21
MANIFOLD - CLEANING, EXHAUST . 9-109,9-185,
9-53
MANIFOLD - CLEANING, INTAKE . . . 9-107,9-184,
9-51
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-109,
9-53
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-89
MANIFOLD - DESCRIPTION, INTAKE . . 9-106,9-50
MANIFOLD - INSPECTION, EXHAUST
.....9-109,
9-186,9-53
MANIFOLD - INSPECTION, INTAKE
. 9-108,9-184,
9-51
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-109,
9-186,9-53
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-90
MANIFOLD - INSTALLATION, INTAKE
.....9-108,
9-184,9-51MANIFOLD - OPERATION, EXHAUST . . 9-109,9-53
MANIFOLD - OPERATION, FUEL DRAIN . . . 14-89
MANIFOLD - OPERATION, INTAKE........9-50
MANIFOLD - REMOVAL, EXHAUST . . 9-109,9-185,
9-53
MANIFOLD - REMOVAL, FUEL DRAIN.....14-90
MANIFOLD - REMOVAL, INTAKE . . . 9-107,9-184,
9-50
MANIFOLD LEAKAGE - DIAGNOSIS AND
TESTING, INTAKE................9-106,9-50
MANUAL - NV4500 - ASSEMBLY........21-21
MANUAL - NV4500 - CLEANING.........21-20
MANUAL - NV4500 - DESCRIPTION.......21-1
MANUAL - NV4500 - DIAGNOSIS AND
TESTING............................21-3
MANUAL - NV4500 - DISASSEMBLY.......21-5
MANUAL - NV4500 - INSPECTION.......21-20
MANUAL - NV4500 - INSTALLATION......21-37
MANUAL - NV4500 - OPERATION.........21-3
MANUAL - NV4500 - REMOVAL..........21-4
MANUAL - NV4500 - SPECIFICATIONS....21-38
MANUAL - NV5600 - ASSEMBLY........21-64
MANUAL - NV5600 - CLEANING.........21-63
MANUAL - NV5600 - DESCRIPTION......21-46
MANUAL - NV5600 - DIAGNOSIS AND
TESTING...........................21-48
MANUAL - NV5600 - DISASSEMBLY......21-49
MANUAL - NV5600 - INSPECTION.........21-63
MANUAL - NV5600 - INSTALLATION......21-78
MANUAL - NV5600 - OPERATION........21-48
MANUAL - NV5600 - REMOVAL.........21-49
MANUAL - NV5600 - SPECIFICATIONS....21-79
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-7
MANUAL TRANSMISSION -
DESCRIPTION.........................0-5
MANUAL TRANSMISSION -
INSTALLATION, SHIFT BOOT...........23-122
MANUAL TRANSMISSION - REMOVAL,
SHIFT BOOT........................23-122
MAP SENSOR - INSTALLATION.........14-108
MARKER LAMP - INSTALLATION........8L-23
MARKER LAMP - REMOVAL............8L-23
MASTER CYLINDER - DESCRIPTION......5-26
MASTER CYLINDER - INSTALLATION......5-28
MASTER CYLINDER - OPERATION........5-26
MASTER CYLINDER - REMOVAL..........5-27
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-27
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-26
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-3
MATS - INSTALLATION, CARPETS AND
FLOOR............................23-123
MATS - REMOVAL, CARPETS AND
FLOOR............................23-123
MEASUREMENT - STANDARD
PROCEDURE, CASTER CORRECTION.......2-3
MEASUREMENTS, SPECIFICATIONS -
BODY GAP AND FLUSH................23-56
MEASURING TIMING CHAIN STRETCH -
INSPECTION....................9-111,9-54
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . . 9-116,9-6,9-61
MECHANISM - DESCRIPTION, SHIFT....21-208,
21-379
MECHANISM - NV4500 - INSTALLATION,
SHIFT..............................21-44
MECHANISM - NV4500 - REMOVAL,
SHIFT..............................21-43
MECHANISM - OPERATION, SHIFT......21-208,
21-379
METRIC SYSTEM - DESCRIPTION......Intro.-9
MICRO-RELAY - DESCRIPTION.......8W-97-13
MICRO-RELAY - DIAGNOSIS AND
TESTING........................8W-97-14
MICRO-RELAY - INSTALLATION......8W-97-14
MICRO-RELAY - OPERATION........8W-97-14
MICRO-RELAY - REMOVAL
..........8W-97-14
MIDTRONICS ELECTRICAL TESTER -
STANDARD PROCEDURE, USING
........8F-15
MIL - DESCRIPTION, MALFUNCTION
INDICATOR LAMP
....................8J-23
MIL - OPERATION, MALFUNCTION
INDICATOR LAMP
....................8J-23
MILE, SPECIFICATIONS - TIRE
REVOLUTIONS PER
....................22-9
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page

PLATE - INSTALLATION, TRANSFER
CASE SKID.........................13-11
PLATE - REMOVAL, TRANSFER CASE
SKID..............................13-11
PLATE LAMP - INSTALLATION, LICENSE . . 8L-22
PLATE LAMP - REMOVAL, LICENSE......8L-22
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-22
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-22
PLATE, SPECIFICATIONS - FUEL
INJECTION PUMP DATA...............14-77
PLATES - INSTALLATION, EXTERIOR
NAME.............................23-89
PLATES - REMOVAL, EXTERIOR NAME....23-89
PLUG - CLEANING, SPARK.............8I-20
PLUG - DESCRIPTION, SPARK...........8I-16
PLUG - INSTALLATION, SPARK..........8I-20
PLUG - INSTALLATION, STEERING GEAR
HOUSING...........................19-30
PLUG - OPERATION, SPARK............8I-16
PLUG - REMOVAL, SPARK..............8I-19
PLUG - REMOVAL, STEERING GEAR
HOUSING...........................19-29
PLUG CABLE - DESCRIPTION, SPARK.....8I-20
PLUG CABLE - INSTALLATION, SPARK....8I-21
PLUG CABLE - OPERATION, SPARK.......8I-20
PLUG CABLE - REMOVAL, SPARK........8I-21
PLUG CABLE ORDER, 8.0L V-10 ENGINE
- SPARK .............................8I-3
PLUG CABLE RESISTANCE,
SPECIFICATIONS - SPARK...............8I-3
PLUG CABLES - DIAGNOSIS AND
TESTING, SPARK.....................8I-20
PLUG CONDITIONS - DIAGNOSIS AND
TESTING, SPARK.....................8I-17
PLUGS, SPECIFICATIONS - SPARK........8I-3
PLUMBING - CLEANING, CHARGE AIR
COOLER............................11-19
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER........................11-18
PLUMBING - INSPECTION, CHARGE AIR
COOLER............................11-19
PLUMBING - INSTALLATION, CHARGE
AIR COOLER........................11-20
PLUMBING - OPERATION, CHARGE AIR
COOLER............................11-18
PLUMBING - REMOVAL, CHARGE AIR
COOLER............................11-18
PLUMBING - SERVICE CAUTIONS........24-42
PLUMBING - SERVICE WARNINGS.......24-42
POLISHING - DESCRIPTION, WET
SANDING/BUFFING..................23-130
PORT - DESCRIPTION, REFRIGERANT
SYSTEM SERVICE.....................24-1
PORT - OPERATION, REFRIGERANT
SYSTEM SERVICE.....................24-2
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-95
POSITION SENSOR - DESCRIPTION,
THROTTLE..........................14-50
POSITION SENSOR - INSTALLATION,
ACCELERATOR PEDAL.................14-97
POSITION SENSOR - OPERATION,
ACCELERATOR PEDAL.................14-95
POSITION SENSOR - OPERATION,
THROTTLE..........................14-50
POSITION SENSOR - REMOVAL,
ACCELERATOR PEDAL.................14-95
POSITION SWITCH - DESCRIPTION,
CLUTCH PEDAL.......................6-17
POSITION SWITCH - DIAGNOSIS AND
TESTING, PARK/NEUTRAL.......21-195,21-367
POSITION SWITCH - INSTALLATION,
PARK/NEUTRAL...............21-195,21-367
POSITION SWITCH - OPERATION,
CLUTCH PEDAL.......................6-17
POSITION SWITCH - REMOVAL,
PARK/NEUTRAL...............21-195,21-367
POSITIVE CABLE INSTALLATION,
GASOLINE ENGINE...................8F-22
POSITIVE CABLE REMOVAL, GASOLINE
ENGINE
............................8F-21
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE
..............8W-01-8
POWER BRAKE BOOSTER -
INSTALLATION
........................5-19
POWER BRAKE BOOSTER - REMOVAL
.....5-19
POWER DISTRIBUTION - DESCRIPTION
. 8W-97-1POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-8
POWER DISTRIBUTION CENTER -
INSTALLATION...................8W-97-10
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-8
POWER DISTRIBUTION CENTER -
REMOVAL........................8W-97-8
POWER DISTRIBUTION SYSTEMS,
SPECIAL TOOLS...................8W-97-2
POWER GROUNDS - DESCRIPTION......8E-17
POWER LOCK & REMOTE KEYLESS
ENTRY SYSTEM - DIAGNOSIS AND
TESTING............................8N-5
POWER LOCK MOTOR - DESCRIPTION....8N-7
POWER LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-7
POWER LOCK MOTOR - OPERATION......8N-7
POWER LOCK SWITCH - DESCRIPTION....8N-8
POWER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-9
POWER LOCK SWITCH - OPERATION......8N-8
POWER LOCKS - DESCRIPTION..........8N-1
POWER LOCKS - DIAGNOSIS AND
TESTING............................8N-4
POWER LOCKS - OPERATION............8N-3
POWER MIRROR SWITCH -
DESCRIPTION.......................8N-13
POWER MIRROR SWITCH -
INSTALLATION......................8N-14
POWER MIRROR SWITCH - OPERATION . . 8N-13
POWER MIRROR SWITCH - REMOVAL . . . 8N-13
POWER MIRRORS - DESCRIPTION......8N-11
POWER MIRRORS - OPERATION........8N-11
POWER OUTLET - DESCRIPTION.....8W-97-10
POWER OUTLET - DIAGNOSIS AND
TESTING........................8W-97-10
POWER OUTLET - INSTALLATION....8W-97-11
POWER OUTLET - OPERATION.......8W-97-10
POWER OUTLET - REMOVAL........8W-97-11
POWER SEAT SWITCH - DESCRIPTION,
DRIVER............................8N-17
POWER SEAT SWITCH - DESCRIPTION,
PASSENGER........................8N-20
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, DRIVER................8N-17
POWER SEAT SWITCH - DIAGNOSIS
AND TESTING, PASSENGER............8N-20
POWER SEAT SWITCH - INSTALLATION,
DRIVER............................8N-18
POWER SEAT SWITCH - INSTALLATION,
PASSENGER........................8N-21
POWER SEAT SWITCH - OPERATION,
DRIVER............................8N-17
POWER SEAT SWITCH - OPERATION,
PASSENGER........................8N-20
POWER SEAT SWITCH - REMOVAL,
DRIVER............................8N-18
POWER SEAT SWITCH - REMOVAL,
PASSENGER........................8N-21
POWER SEAT SYSTEM - DESCRIPTION . . . 8N-16
POWER SEAT SYSTEM - DIAGNOSIS
AND TESTING.......................8N-16
POWER SEAT SYSTEM - OPERATION.....8N-16
POWER SEAT TRACK - DESCRIPTION....8N-21
POWER SEAT TRACK - DIAGNOSIS AND
TESTING...........................8N-22
POWER SEAT TRACK - INSTALLATION....8N-22
POWER SEAT TRACK - OPERATION......8N-22
POWER SEAT TRACK - REMOVAL.......8N-22
POWER STEERING FLOW AND
PRESSURE - DIAGNOSIS AND
TESTING............................19-4
POWER STEERING GEAR LEAKAGE -
DIAGNOSIS AND TESTING.............19-16
POWER STEERING GEAR, SPECIAL
TOOLS.............................19-22
POWER STEERING GEAR,
SPECIFICATIONS
.....................19-21
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE
. . . 19-33
POWER STEERING PUMP, SPECIAL
TOOLS
.............................19-38
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING
..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING
.....19-34POWER WINDOW SWITCH -
DESCRIPTION.......................8N-24
POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING.......................8N-24
POWER WINDOW SWITCH -
INSTALLATION......................8N-26
POWER WINDOW SWITCH - OPERATION . . 8N-24
POWER WINDOW SWITCH - REMOVAL . . . 8N-25
POWER WINDOWS - DESCRIPTION......8N-23
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-23
POWER WINDOWS - OPERATION........8N-23
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-9
POWR-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-99
POWR-LOK - DISASSEMBLY,
DIFFERENTIAL........................3-99
POWR-LOK - DIAGNOSIS AND TESTING . . . 3-99
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-4
PRESSURE - DESCRIPTION, HOSES......19-39
PRESSURE - DIAGNOSIS AND TESTING,
BOOST.............................14-93
PRESSURE - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION...........9-64,9-9
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL................9-101,9-178,9-45
PRESSURE - DIAGNOSIS AND TESTING,
FUEL TRANSFER PUMP...............14-84
PRESSURE - DIAGNOSIS AND TESTING,
POWER STEERING FLOW.................19-4
PRESSURE - DIAGNOSIS AND TESTING,
TURBOCHARGER BOOST...............11-13
PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL SYSTEM.........14-3
PRESSURE - OPERATION, HOSES........19-39
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-8
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-64
PRESSURE CAP - OPERATION,
RADIATOR...........................7-64
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE...................22-7
PRESSURE FUEL LINES - DESCRIPTION,
HIGH..............................14-78
PRESSURE FUEL LINES - OPERATION,
HIGH..............................14-78
PRESSURE GAUGE - DESCRIPTION, OIL . . 8J-25
PRESSURE GAUGE - OPERATION, OIL....8J-25
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-8
PRESSURE LEAK DOWN TEST -
DIAGNOSIS AND TESTING, FUEL.........14-2
PRESSURE LEAKAGE - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION....9-64,9-9
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-3
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-180
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH
..................24-46
PRESSURE RELIEF VALVE - INSPECTION,
OIL
................................9-180
PRESSURE RELIEF VALVE -
INSTALLATION, OIL
...................9-180
PRESSURE RELIEF VALVE - OPERATION,
HIGH
..............................24-47
PRESSURE RELIEF VALVE - REMOVAL,
OIL
................................9-180
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL
...................9-181
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL
......................9-181
PRESSURE SWITCH - DESCRIPTION, A/C
HIGH
..............................24-20
PRESSURE SWITCH - DESCRIPTION, A/C
LOW
..............................24-21
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C HIGH
...................24-20
PRESSURE SWITCH - DIAGNOSIS AND
TESTING, A/C LOW
...................24-21
PRESSURE SWITCH - INSTALLATION,
A/C HIGH
...........................24-20
PRESSURE SWITCH - INSTALLATION,
A/C LOW
...........................24-21
BR/BEINDEX 23
Description Group-Page Description Group-Page Description Group-Page

SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-7
SENSOR - REMOVAL, O2..............14-46
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-40
SENSOR - REMOVAL, WATER IN FUEL....14-89
SENSOR RETURN - DESCRIPTION.......8E-17
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE.........................9-181
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE.........................9-181
SEPARATOR - DESCRIPTION, FUEL
FILTER / WATER .....................14-63
SEPARATOR - INSTALLATION, FUEL
FILTER / WATER .....................14-65
SEPARATOR - OPERATION, FUEL FILTER
/ WATER ...........................14-63
SEPARATOR - REMOVAL, FUEL FILTER /
WATER.............................14-64
SERVO - ASSEMBLY, FRONT.....21-164,21-335
SERVO - ASSEMBLY, REAR......21-207,21-379
SERVO - CLEANING, FRONT.....21-164,21-334
SERVO - CLEANING, REAR......21-207,21-379
SERVO - DESCRIPTION, FRONT . . 21-164,21-334
SERVO - DESCRIPTION, REAR . . . 21-207,21-378
SERVO - DESCRIPTION, SPEED
CONTROL...........................8P-6
SERVO - DISASSEMBLY, FRONT . . 21-164,21-334
SERVO - DISASSEMBLY, REAR . . . 21-207,21-378
SERVO - INSPECTION, FRONT.....21-164,21-335
SERVO - OPERATION, FRONT....21-164,21-334
SERVO - OPERATION, REAR.....21-207,21-378
SERVO - OPERATION, SPEED CONTROL . . . 8P-6
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-9
SHAFT - ASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-199,21-371
SHAFT - DESCRIPTION, PLANETARY
GEARTRAIN/OUTPUT...........21-197,21-369
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - DISASSEMBLY, PLANETARY
GEARTRAIN/OUTPUT...........21-198,21-369
SHAFT - FRONT - INSTALLATION,
PROPELLER...........................3-7
SHAFT - FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT - INSPECTION, PLANETARY
GEARTRAIN/OUTPUT...........21-199,21-371
SHAFT - INSTALLATION, PITMAN........19-25
SHAFT - INSTALLATION, WORM.........19-31
SHAFT - OPERATION, PLANETARY
GEARTRAIN/OUTPUT...........21-197,21-369
SHAFT - REAR - INSTALLATION,
PROPELLER...........................3-7
SHAFT - REAR - REMOVAL, PROPELLER....3-7
SHAFT - REMOVAL, PITMAN............19-24
SHAFT - REMOVAL, WORM............19-30
SHAFT - STANDARD PROCEDURES,
PROPELLER...........................3-3
SHAFT FRONT BEARING -
INSTALLATION, OUTPUT........21-171,21-342
SHAFT FRONT BEARING - REMOVAL,
OUTPUT.....................21-171,21-342
SHAFT REAR BEARING - INSTALLATION,
OUTPUT.....................21-172,21-343
SHAFT REAR BEARING - REMOVAL,
OUTPUT.....................21-171,21-343
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.....................21-461,21-498
SHAFT SEAL - INSTALLATION, PITMAN
. . . 19-26
SHAFT SEAL - REMOVAL, FRONT
OUTPUT
.....................21-461,21-498
SHAFT SEAL - REMOVAL, PITMAN
.......19-25
SHAFT SEALS - INSTALLATION, AXLE
.....3-31
SHAFT SEALS - REMOVAL, AXLE
.........3-31
SHAFT, SPECIAL TOOLS - PROPELLER
......3-6
SHAFT, SPECIFICATIONS - PROPELLER
.....3-6
SHAFTS - INSTALLATION,
AXLE
..................3-123,3-29,3-62,3-94
SHAFTS - INTERMEDIATE - REMOVAL,
AXLE
...............................3-30
SHAFTS - REMOVAL, AXLE
. 3-123,3-29,3-62,3-94
SHIELD - INSTALLATION, REAR SPLASH
. . 23-96
SHIELD - REMOVAL, REAR SPLASH
......23-96
SHIELDS - DESCRIPTION, HEAT
.........11-10SHIELDS - INSTALLATION, FRONT END
SPLASH............................23-92
SHIELDS - INSTALLATION, HEAT........11-10
SHIELDS - REMOVAL, FRONT END
SPLASH............................23-92
SHIELDS - REMOVAL, HEAT............11-10
SHIFT BOOT - INSTALLATION, 4WD
FLOOR............................23-122
SHIFT BOOT - MANUAL TRANSMISSION
- INSTALLATION....................23-122
SHIFT BOOT - MANUAL TRANSMISSION
- REMOVAL........................23-122
SHIFT BOOT - REMOVAL, 4WD FLOOR . . . 23-122
SHIFT COVER - NV4500 - INSTALLATION . . 21-45
SHIFT COVER - NV4500 - REMOVAL.....21-45
SHIFT COVER - NV5600 - INSTALLATION . . 21-86
SHIFT COVER - NV5600 - REMOVAL.....21-86
SHIFT INDICATOR (TRANSFER CASE) -
DESCRIPTION.......................8J-28
SHIFT INDICATOR (TRANSFER CASE) -
OPERATION.........................8J-28
SHIFT LEVER - ADJUSTMENT....21-463,21-500
SHIFT LEVER - INSTALLATION . . . 21-462,21-500
SHIFT LEVER - INSTALLATION, GEAR.....19-15
SHIFT LEVER - REMOVAL.......21-462,21-499
SHIFT LEVER - REMOVAL, GEAR........19-14
SHIFT MECHANISM - DESCRIPTION....21-208,
21-379
SHIFT MECHANISM - NV4500 -
INSTALLATION........................21-44
SHIFT MECHANISM - NV4500 -
REMOVAL..........................21-43
SHIFT MECHANISM - OPERATION......21-208,
21-379
SHOCK - DIAGNOSIS AND TESTING . . . 2-11,2-22
SHOCK - DIAGNOSIS AND TESTING,
SPRING.............................2-25
SHOCK - INSTALLATION........2-11,2-22,2-27
SHOCK - REMOVAL............2-11,2-22,2-27
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-33
SHOES - INSTALLATION................5-32
SHOES - REMOVAL....................5-32
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ...........................8W-01-9
SHUTFACE HANDLE - INSTALLATION.....23-83
SHUTFACE HANDLE - REMOVAL.........23-83
SIDE MOLDINGS - INSTALLATION, BODY . . 23-87
SIDE MOLDINGS - REMOVAL, BODY.....23-86
SIDE PANEL SPEAKER - INSTALLATION,
REAR CAB..........................8A-20
SIDE PANEL SPEAKER - REMOVAL,
REAR CAB..........................8A-20
SIDE VIEW MIRROR - INSTALLATION.....23-98
SIDE VIEW MIRROR - LOW MOUNTED -
INSTALLATION.......................23-98
SIDE VIEW MIRROR - LOW MOUNTED -
REMOVAL..........................23-98
SIDE VIEW MIRROR - REMOVAL........23-97
SIDE VIEW MIRROR FLAG -
INSTALLATION.......................23-75
SIDE VIEW MIRROR FLAG - REMOVAL . . . 23-74
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-98
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-98
SIDEVIEW MIRROR - DESCRIPTION......8N-14
SIDEVIEW MIRROR - DIAGNOSIS AND
TESTING...........................8N-14
SIDEVIEW MIRROR - OPERATION.......8N-14
SIDEVIEW MIRROR - REMOVAL.........8N-15
SIGNAL & HAZARD WARNING SYSTEM -
DESCRIPTION, TURN..................8L-2
SIGNAL & HAZARD WARNING SYSTEM -
DIAGNOSIS AND TESTING, TURN.........8L-3
SIGNAL & HAZARD WARNING SYSTEM -
OPERATION, TURN....................8L-2
SIGNAL CANCEL CAM - DESCRIPTION,
TURN
..............................8L-31
SIGNAL CANCEL CAM - OPERATION,
TURN
..............................8L-31
SIGNAL GROUND - DESCRIPTION
.......8E-17
SIGNAL INDICATOR - DESCRIPTION,
TURN
..............................8J-32
SIGNAL INDICATOR - DIAGNOSIS AND
TESTING, TURN
......................8J-32SIGNAL INDICATOR - OPERATION, TURN . . 8J-32
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-29
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-29
SIGNAL LAMP UNIT - INSTALLATION,
PARK/TURN.........................8L-29
SIGNAL LAMP UNIT - REMOVAL,
PARK/TURN.........................8L-29
SILENCER PAD - INSTALLATION........23-104
SILENCER PAD - REMOVAL...........23-104
SILL TRIM - INSTALLATION, DOOR.....23-121
SILL TRIM - REMOVAL, DOOR.........23-121
SINGLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY...........................3-9
SINGLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY.........................3-8
SINGLE CARDAN UNIVERSAL JOINTS -
INSTALLATION........................3-35
SINGLE CARDAN UNIVERSAL JOINTS -
REMOVAL...........................3-34
SKID PLATE - INSTALLATION, TRANSFER
CASE..............................13-11
SKID PLATE - REMOVAL, TRANSFER
CASE..............................13-11
SLAM BUMPER - INSTALLATION........23-67
SLAM BUMPER - REMOVAL............23-67
SMOKE DIAGNOSIS CHARTS -
DIAGNOSIS AND TESTING.............9-118
SOLENOID - DESCRIPTION......21-208,21-380
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-33
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-34
SOLENOID - OPERATION........21-209,21-381
SOLENOID - OPERATION, EVAP/PURGE . . . 25-33
SOLENOID - REMOVAL, EVAP/PURGE.....25-33
SOLID LIFTERS/TAPPETS - CLEANING....9-164
SOLID LIFTERS/TAPPETS - INSPECTION . . 9-165
SOLID LIFTERS/TAPPETS -
INSTALLATION.......................9-165
SOLID LIFTERS/TAPPETS - REMOVAL....9-164
SPARE TIRE - DESCRIPTION............22-10
SPARE TIRE - TEMPORARY -
DESCRIPTION........................22-6
SPARK PLUG - CLEANING..............8I-20
SPARK PLUG - DESCRIPTION...........8I-16
SPARK PLUG - INSTALLATION...........8I-20
SPARK PLUG - OPERATION.............8I-16
SPARK PLUG - REMOVAL..............8I-19
SPARK PLUG CABLE - DESCRIPTION.....8I-20
SPARK PLUG CABLE - INSTALLATION.....8I-21
SPARK PLUG CABLE - OPERATION.......8I-20
SPARK PLUG CABLE - REMOVAL........8I-21
SPARK PLUG CABLE ORDER, 8.0L V-10
ENGINE..............................8I-3
SPARK PLUG CABLE RESISTANCE,
SPECIFICATIONS......................8I-3
SPARK PLUG CABLES - DIAGNOSIS AND
TESTING............................8I-20
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-17
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-17
SPEAKER - DIAGNOSIS AND TESTING....8A-17
SPEAKER - INSTALLATION, A-PILLAR
TWEETER..........................8A-19
SPEAKER - INSTALLATION, FRONT DOOR . 8A-19
SPEAKER - INSTALLATION, REAR CAB
SIDE PANEL........................8A-20
SPEAKER - INSTALLATION, REAR DOOR . . 8A-21
SPEAKER - OPERATION...............8A-17
SPEAKER - REMOVAL, A-PILLAR
TWEETER..........................8A-18
SPEAKER - REMOVAL, FRONT DOOR.....8A-19
SPEAKER - REMOVAL, REAR CAB SIDE
PANEL.............................8A-20
SPEAKER - REMOVAL, REAR DOOR......8A-20
SPECIAL TOOL, SPECIAL TOOLS -
OVERHEAD CONSOLE.................8M-9
SPECIFICATIONS - 2002 BR/BE PAINT
COLOR CODES.....................23-129
SPECIFICATIONS - 5.9L DIESEL.........9-127
SPECIFICATIONS - 5.9L ENGINE..........9-13
SPECIFICATIONS - 8.OL ENGINE
..........9-68
SPECIFICATIONS - A/C APPLICATION
TABLE
..............................24-7
SPECIFICATIONS - ALIGNMENT
...........2-6
SPECIFICATIONS - BASE BRAKE
...........5-2
SPECIFICATIONS - BATTERY
.............8F-6
28 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page