key battery DODGE RAM 2002 Service Workshop Manual

(M)Malfunction Indicator Lamp (MIL) illuminated during engine operation if this DTC was recorded
(depending if required by CARB and/or EPA). MIL is displayed as an engine icon on instrument panel.
(G)Generator lamp illuminated
Generic Scan
Tool P-CodeDRB Scan Tool Display Brief Description of DTC
P1496 5 Volt Supply, Output Too Low 5 volt sensor feed is sensed to be below an acceptable limit.
( less than 4v for 4 sec )
P1498 High Speed Rad Fan Ground CTRL
Rly CircuitAn open or shorted condition detected in the control circuit of
the #3 high speed radiator fan control relay.
P1499 Hydraulic cooling fan solenoid circuit An open or shorted condition detected in the cooling fan
control solenoid circuit.
P1594 (G) Charging System Voltage Too High Battery voltage sense input above target charging voltage
during engine operation.
P1594 Charging System Voltage Too High Battery voltage sense input above target charging voltage
during engine operation.
P1595 Speed Control Solenoid Circuits An open or shorted condition detected in either of the speed
control vacuum or vent solenoid control circuits.
P1595 Speed Control Solenoid Circuits An open or shorted condition detected in the speed control
vacuum or vent solenoid circuits.
P1596 Speed Control Switch Always High Speed control switch input above maximum acceptable
voltage.
P1597 Speed Control Switch Always Low Speed control switch input below minimum acceptable
voltage.
P1597 Speed Control Switch Always Low Speed control switch input below the minimum acceptable
voltage.
P1598 A/C Pressure Sensor Volts Too High A/C pressure sensor input above maximum acceptable
voltage.
P1598 A/C Sensor Input Hi Problem detected in air conditioning electrical circuit.
P1599 A/C Pressure Sensor Volts Too Low A/C pressure sensor input below minimum acceptable
voltage.
P1599 A/C Sensor Input Lo Problem detected in air conditioning electrical circuit.
P1602 PCM not programmed
P1680 Clutch Released Switch Circuit Problem detected in clutch switch electrical circuit.
P1681 No I/P Cluster CCD/J1850 Messages
ReceivedNo CCD/J1850 messages received from the cluster control
module.
P1682 (G) Charging System Voltage Too Low Battery voltage sense input below target charging voltage
during engine operation and no significant change in voltage
detected during active test of generator output circuit.
P1682 Charging System Voltage Too Low Charging system output voltage low.
P1683 SPD CTRL PWR Relay; or S/C 12v
Driver CKTAn open or shorted condition detected in the speed control
servo power control circuit.
P1683 Spd ctrl pwr rly, or s/c 12v driver circuit An open or shorted condition detected in the speed control
servo power control circuit.
P1684 Batt Loss (disconnected) in last 50
StartsThe battery has been disconnected within the last 50 starts
P1685 SKIM Invalid Key - (Wrong or Invalid
Key MSG Received From SKIM)The engine controler has received an invalid key from the
SKIM.
25 - 14 EMISSIONS CONTROLBR/BE
EMISSIONS CONTROL (Continued)

AXLE BEARINGS - INSTALLATION . . . 3-123,3-62,
3-94
AXLE BEARINGS - REMOVAL . . . 3-123,3-62,3-94
AXLE LUBRICATION - DESCRIPTION.......0-5
AXLE SHAFT SEALS - INSTALLATION......3-31
AXLE SHAFT SEALS - REMOVAL.........3-31
AXLE SHAFTS - INSTALLATION . 3-123,3-29,3-62,
3-94
AXLE SHAFTS - INTERMEDIATE -
REMOVAL...........................3-30
AXLE SHAFTS - REMOVAL . 3-123,3-29,3-62,3-94
AXLE, SPECIAL TOOLS - FRONT..........3-27
AXLE VACUUM MOTOR - ASSEMBLY......3-34
AXLE VACUUM MOTOR - DESCRIPTION....3-31
AXLE VACUUM MOTOR - DISASSEMBLY . . . 3-34
AXLE VACUUM MOTOR - INSTALLATION . . . 3-34
AXLE VACUUM MOTOR - OPERATION.....3-31
AXLE VACUUM MOTOR - REMOVAL.......3-34
BACKLITE - INSTALLATION............23-145
BACKLITE - REMOVAL................23-145
BACKLITE LATCH AND KEEPER -
INSTALLATION......................23-146
BACKLITE LATCH AND KEEPER -
REMOVAL.........................23-146
BACKLITE VENT GLASS - INSTALLATION . 23-146
BACKLITE VENT GLASS - REMOVAL.....23-146
BAFFLE - INSTALLATION, HVAC
HOUSING INLET.....................24-36
BAFFLE - REMOVAL, HVAC HOUSING
INLET..............................24-35
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-4
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-10
BALL JOINT - DIAGNOSIS AND TESTING,
UPPER..............................2-12
BAND OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING
TRANSMISSION CLUTCH.......21-100,21-272
BANDS - ADJUSTMENT.........21-151,21-321
BANDS - DESCRIPTION.........21-150,21-320
BANDS - OPERATION..........21-151,21-321
BAR - DIAGNOSIS AND TESTING, TRACK . . . 2-24
BAR - INSTALLATION, STABILIZER . . . 2-12,2-23,
2-29
BAR - INSTALLATION, TRACK............2-24
BAR - REMOVAL, STABILIZER . . . 2-12,2-23,2-29
BAR - REMOVAL, TRACK...............2-24
BARRELS - INSTALLATION, PANEL
OUTLET............................24-31
BARRELS - REMOVAL, PANEL OUTLET . . . 24-31
BASE BRAKE, SPECIFICATIONS............5-2
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-5
BASE BRAKES, SPECIAL TOOLS...........5-4
BASE COAT/CLEAR COAT FINISH -
DESCRIPTION......................23-129
BASE COAT/CLEAR COAT FINISH -
OPERATION........................23-129
BATTERIES - STANDARD PROCEDURE,
REMOTE KEYLESS ENTRY
TRANSMITTER.......................8N-8
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-7
BATTERY CABLE - DESCRIPTION........8F-18
BATTERY CABLE - OPERATION..........8F-18
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-19
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION
....8F-17
BATTERY HOLDDOWN - INSTALLATION
. . . 8F-18
BATTERY HOLDDOWN - OPERATION
.....8F-17
BATTERY HOLDDOWN - REMOVAL
.......8F-17
BATTERY, SPECIFICATIONS
..............8F-6
BATTERY SYSTEM - CLEANING
...........8F-5
BATTERY SYSTEM - DESCRIPTION
........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING
............................8F-2
BATTERY SYSTEM - INSPECTION
.........8F-6
BATTERY SYSTEM - OPERATION
.........8F-2
BATTERY TEMPERATURE SENSOR -
DESCRIPTION
.......................8F-27
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-28
BATTERY TEMPERATURE SENSOR -
OPERATION
.........................8F-27BATTERY TEMPERATURE SENSOR -
REMOVAL..........................8F-27
BATTERY TRAY - DESCRIPTION.........8F-23
BATTERY TRAY - INSTALLATION.........8F-24
BATTERY TRAY - OPERATION...........8F-23
BATTERY TRAY - REMOVAL............8F-23
BEAM INDICATOR - DESCRIPTION, HIGH . . 8J-21
BEAM INDICATOR - DIAGNOSIS AND
TESTING, HIGH......................8J-21
BEAM INDICATOR - OPERATION, HIGH....8J-21
BEARING - ADJUSTMENT, CENTER.........3-8
BEARING - INSTALLATION, CENTER........3-8
BEARING - INSTALLATION, CLUTCH
RELEASE............................6-12
BEARING - INSTALLATION, HUB.......2-17,2-9
BEARING - INSTALLATION, OUTPUT
SHAFT FRONT................21-171,21-342
BEARING - INSTALLATION, OUTPUT
SHAFT REAR.................21-172,21-343
BEARING - INSTALLATION, PILOT........6-14
BEARING - INSTALLATION, PITMAN......19-23
BEARING - REMOVAL, CENTER...........3-8
BEARING - REMOVAL, CLUTCH RELEASE . . . 6-12
BEARING - REMOVAL, HUB..........2-16,2-9
BEARING - REMOVAL, OUTPUT SHAFT
FRONT......................21-171,21-342
BEARING - REMOVAL, OUTPUT SHAFT
REAR.......................21-171,21-343
BEARING - REMOVAL, PILOT..............6-14
BEARING - REMOVAL, PITMAN..........19-22
BEARING AND CRANKSHAFT JOURNAL
CLEARANCE - STANDARD
PROCEDURE, CONNECTING ROD........9-158
BEARING CLEARANCE - STANDARD
PROCEDURE, MAIN...................9-159
BEARING FITTING - STANDARD
PROCEDURE, CONNECTING ROD.....9-29,9-87
BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT MAIN........9-31
BEARINGS - DESCRIPTION,
CRANKSHAFT MAIN...................9-31
BEARINGS - INSTALLATION, AXLE . . . 3-123,3-62,
3-94
BEARINGS - INSTALLATION, CAMSHAFT . . 9-157,
9-28,9-86
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN...............9-32,9-88
BEARINGS - INSTALLATION,
DIFFERENTIAL CASE.....3-102,3-129,3-41,3-72
BEARINGS - OPERATION, CRANKSHAFT
MAIN...............................9-31
BEARINGS - REMOVAL, AXLE . . . 3-123,3-62,3-94
BEARINGS - REMOVAL, CAMSHAFT . 9-152,9-27,
9-85
BEARINGS - REMOVAL, CRANKSHAFT
MAIN...........................9-31,9-88
BEARINGS - REMOVAL, DIFFERENTIAL
CASE.................3-102,3-129,3-40,3-72
BEARINGS - STANDARD PROCEDURE,
FITTING CRANKSHAFT MAIN............9-88
BELT / CHAIN COVER(S) -
INSTALLATION, TIMING...........9-110,9-54
BELT / CHAIN COVER(S) - REMOVAL,
TIMING........................9-110,9-53
BELT - DIAGNOSIS AND TESTING,
ACCESSORY DRIVE............7-24,7-27,7-30
BELT & RETRACTOR - INSTALLATION,
REAR SEAT.........................8O-26
BELT & RETRACTOR - REMOVAL, REAR
SEAT ..............................8O-26
BELT BUCKLE - INSTALLATION, FRONT
SEAT ..............................8O-20
BELT BUCKLE - INSTALLATION, REAR
SEAT ..............................8O-27
BELT BUCKLE - REMOVAL, FRONT SEAT . . 8O-20
BELT BUCKLE - REMOVAL, REAR SEAT . . . 8O-27
BELT SWITCH - DESCRIPTION, SEAT.....8O-28
BELT SWITCH - DIAGNOSIS AND
TESTING, SEAT......................8O-28
BELT SWITCH - OPERATION, SEAT.......8O-28
BELT TENSIONERS - 5.9L -
DESCRIPTION
........................7-19
BELT TENSIONERS - 5.9L -
INSTALLATION
........................7-20
BELT TENSIONERS - 5.9L - OPERATION
....7-19
BELT TENSIONERS - 5.9L - REMOVAL
.....7-19
BELT TENSIONERS - 5.9L DIESEL -
DESCRIPTION
........................7-23BELT TENSIONERS - 5.9L DIESEL -
INSTALLATION........................7-23
BELT TENSIONERS - 5.9L DIESEL -
OPERATION..........................7-23
BELT TENSIONERS - 5.9L DIESEL -
REMOVAL...........................7-23
BELT TENSIONERS - 8.0L -
DESCRIPTION........................7-20
BELT TENSIONERS - 8.0L -
INSTALLATION........................7-22
BELT TENSIONERS - 8.0L - OPERATION....7-21
BELT TENSIONERS - 8.0L - REMOVAL.....7-21
BELT TURNING LOOP ADJUSTER -
INSTALLATION, SEAT.................8O-29
BELT TURNING LOOP ADJUSTER -
REMOVAL, SEAT.....................8O-29
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR INNER.................23-153
BELT WEATHERSTRIP - INSTALLATION,
FRONT DOOR OUTER................23-153
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR INNER.................23-153
BELT WEATHERSTRIP - REMOVAL,
FRONT DOOR OUTER................23-153
BELT/CHAIN AND SPROCKETS -
INSTALLATION, TIMING...........9-111,9-55
BELT/CHAIN AND SPROCKETS -
REMOVAL, TIMING...............9-111,9-54
BELTS - 5.9L - INSTALLATION, DRIVE.....7-26
BELTS - 5.9L - REMOVAL, DRIVE.........7-26
BELTS - 5.9L DIESEL - INSTALLATION,
DRIVE..............................7-32
BELTS - 5.9L DIESEL - REMOVAL, DRIVE . . 7-32
BELTS - 8.0L - INSTALLATION, DRIVE.....7-29
BELTS - 8.0L - REMOVAL, DRIVE.........7-29
BENCH - INSTALLATION, SEAT - SPLIT . . 23-134
BENCH - INSTALLATION, SEAT BACK -
SPLIT.............................23-136
BENCH - INSTALLATION, SEAT BACK
COVER - SPLIT.....................23-137
BENCH - INSTALLATION, SEAT CUSHION
COVER - SPLIT.....................23-140
BENCH - INSTALLATION, SEAT TRACK -
SPLIT.............................23-142
BENCH - REMOVAL, SEAT - SPLIT......23-133
BENCH - REMOVAL, SEAT BACK - SPLIT . 23-135
BENCH - REMOVAL, SEAT BACK COVER
- SPLIT...........................23-137
BENCH - REMOVAL, SEAT CUSHION
COVER - SPLIT.....................23-139
BENCH - REMOVAL, SEAT TRACK -
SPLIT.............................23-142
BENCH SEAT - INSTALLATION, SEAT....23-133
BENCH SEAT - INSTALLATION, SEAT
BACK.............................23-135
BENCH SEAT - REMOVAL, SEAT........23-133
BENCH SEAT - REMOVAL, SEAT BACK . . . 23-135
BEZEL - INSTALLATION, CLUSTER......23-108
BEZEL - REMOVAL, CLUSTER..........23-108
BIN - INSTALLATION, CUBBY..........23-109
BIN - INSTALLATION, STORAGE........23-114
BIN - REMOVAL, CUBBY..............23-108
BIN - REMOVAL, STORAGE............23-114
BLADE - DESCRIPTION, WIPER.........8R-12
BLADE - INSTALLATION, WIPER.........8R-13
BLADE - OPERATION, WIPER...........8R-13
BLADE - REMOVAL, WIPER............8R-13
BLEED - STANDARD PROCEDURE, AIR....14-61
BLEEDING - STANDARD PROCEDURE......5-19
BLEEDING - STANDARD PROCEDURE,
MANUAL.............................5-7
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...................5-27
BLEEDING - STANDARD PROCEDURE,
PRESSURE...........................5-8
BLEEDING ABS BRAKE SYSTEM -
STANDARD PROCEDURE................5-36
BLEND DOOR - INSTALLATION..........24-37
BLEND DOOR - REMOVAL.............24-37
BLEND DOOR ACTUATOR -
INSTALLATION.......................24-25
BLEND DOOR ACTUATOR - REMOVAL
....24-25
BLOCK - CLEANING, ENGINE
........9-27,9-85
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR
...................24-23
BLOCK - DESCRIPTION, JUNCTION
....8W-97-6
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR
............24-23
BR/BEINDEX 3
Description Group-Page Description Group-Page Description Group-Page

HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-78
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-78
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-47
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-20
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-20
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-78
HINGE - INSTALLATION.....23-100,23-72,23-80
HINGE - REMOVAL........23-100,23-72,23-79
HITCH - INSTALLATION, TRAILER.........13-11
HITCH - REMOVAL, TRAILER...........13-11
HOISTING - STANDARD PROCEDURE.......0-9
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDER - INSTALLATION, CUP........23-110
HOLDER - REMOVAL, CUP............23-109
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE..................9-11,9-65
HOOD - INSTALLATION...............23-101
HOOD - REMOVAL...................23-101
HOOK - INSTALLATION, COAT..........23-125
HOOK - INSTALLATION, FRONT TOW.....13-10
HOOK - REMOVAL, COAT.............23-124
HOOK - REMOVAL, FRONT TOW.........13-10
HORN - DESCRIPTION.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - OPERATION...............8H-1,8H-2
HORN - REMOVAL....................8H-2
HORN RELAY - DESCRIPTION.......8W-97-12
HORN RELAY - DESCRIPTION...........8H-3
HORN RELAY - DIAGNOSIS AND
TESTING........................8W-97-12
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION.......8W-97-12
HORN RELAY - INSTALLATION...........8H-4
HORN RELAY - OPERATION.............8H-3
HORN RELAY - REMOVAL..........8W-97-12
HORN RELAY - REMOVAL..............8H-4
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HORN SWITCH - REMOVAL.............8H-5
HOSE CLAMPS - DESCRIPTION...........7-4
HOSE CLAMPS - OPERATION.............7-4
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-76
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-73
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-76
HOSES - PRESSURE - DESCRIPTION
.....19-39
HOSES - PRESSURE - OPERATION
.......19-39
HOSES - RETURN - DESCRIPTION
.......19-39
HOSES - RETURN - OPERATION
.........19-39
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-43HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-9
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH......6-11
HOUSING - INSTALLATION, GEAR........9-188
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - REMOVAL, CLUTCH..........6-11
HOUSING - REMOVAL, GEAR...........9-187
HOUSING - REMOVAL, HVAC...........24-34
HOUSING BUSHING - INSTALLATION,
EXTENSION..................21-156,21-326
HOUSING BUSHING - REMOVAL,
EXTENSION..................21-156,21-326
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-460,21-497
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-460,21-497
HOUSING COVER - INSTALLATION, GEAR . 9-190
HOUSING COVER - REMOVAL, GEAR.....9-189
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-101,21-273
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-36
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-35
HOUSING PLUG - INSTALLATION,
STEERING GEAR.......................19-30
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-29
HOUSING SEAL - INSTALLATION,
EXTENSION..................21-156,21-327
HOUSING SEAL - NV4500 -
INSTALLATION, ADAPTER..............21-42
HOUSING SEAL - NV4500 -
INSTALLATION, EXTENSION............21-42
HOUSING SEAL - NV4500 - REMOVAL,
ADAPTER...........................21-42
HOUSING SEAL - NV4500 - REMOVAL,
EXTENSION.........................21-42
HOUSING SEAL - NV5600 -
INSTALLATION, ADAPTER..............21-85
HOUSING SEAL - NV5600 -
INSTALLATION, EXTENSION............21-85
HOUSING SEAL - NV5600 - REMOVAL,
ADAPTER...........................21-85
HOUSING SEAL - NV5600 - REMOVAL,
EXTENSION.........................21-85
HOUSING SEAL - REMOVAL,
EXTENSION..................21-156,21-326
HUB / BEARING - INSTALLATION......2-17,2-9
HUB / BEARING - REMOVAL..........2-16,2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HVAC HOUSING INLET BAFFLE -
INSTALLATION.......................24-36
HVAC HOUSING INLET BAFFLE -
REMOVAL..........................24-35
HVAC SYSTEM AIRFLOW - DESCRIPTION . 24-30
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-18
HYDRAULIC LIFTERS - CLEANING
....9-37,9-92
HYDRAULIC LIFTERS - INSTALLATION
. 9-37,9-92
HYDRAULIC LIFTERS - REMOVAL
....9-37,9-92
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING
.......21-270,21-98
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS
..............21-132,21-302
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING
........................9-36,9-91
HYDRAULIC/MECHANICAL -
DESCRIPTION
.........................5-4
HYDRAULIC/MECHANICAL - WARNING
.....5-4
HYDROMETER TEST - STANDARD
PROCEDURE
........................8F-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
................9-11,9-122,9-66
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD
.........................8L-29IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT.......................Intro.-3
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-40
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-40
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 5.9L
ENGINES............................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-4
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING....19-9
IGNITION TIMING, SPECIFICATIONS.......8I-4
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-15
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-20
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-27
INDICATOR - DESCRIPTION, TRANS
OVERTEMP.........................8J-31
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATOR - DESCRIPTION, UPSHIFT....8J-32
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-21
INDICATOR - DIAGNOSIS AND TESTING,
TURN SIGNAL
.......................8J-32
INDICATOR - DIAGNOSIS AND TESTING,
VTSS
...............................8Q-4
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID
......................8J-35
INDICATOR - OPERATION, ABS
..........8J-14
INDICATOR - OPERATION, AIRBAG
.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-15
INDICATOR - OPERATION, CHECK
GAUGES
............................8J-17
INDICATOR - OPERATION, CRUISE
.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR
..........................8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-21
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, SEATBELT
.....8J-27
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

SUPPLY RESTRICTIONS - DIAGNOSIS
AND TESTING, FUEL..................14-60
SUPPLY TEST - DIAGNOSIS AND
TESTING, VACUUM....................8P-3
SUPPORT - INSTALLATION, LUMBAR....23-133
SUPPORT - REMOVAL, LUMBAR.......23-132
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-126
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-12
SUPPRESSION COMPONENTS -
DIAGNOSIS AND TESTING, RADIO
NOISE.............................8A-12
SUSPENSION - STANDARD PROCEDURE,
ALIGNMENT LINK/COIL..................2-5
SUSPENSION, SPECIAL TOOLS -
INDEPENDENT FRONT...................2-9
SUSPENSION, SPECIAL TOOLS -
LINK/COIL...........................2-16
SUSPENSION-REAR, SPECIAL TOOLS.....2-27
SWITCH - DESCRIPTION...............8P-12
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE.........................24-20
SWITCH - DESCRIPTION, A/C LOW
PRESSURE.........................24-21
SWITCH - DESCRIPTION, BLOWER
MOTOR............................24-24
SWITCH - DESCRIPTION, BRAKE LAMP....8L-4
SWITCH - DESCRIPTION, CLUTCH
PEDAL POSITION.....................6-17
SWITCH - DESCRIPTION, DOOR AJAR....8L-34
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK......................8N-5
SWITCH - DESCRIPTION, DRIVER
POWER SEAT.......................8N-17
SWITCH - DESCRIPTION, DRIVER SEAT
HEATER.............................8G-7
SWITCH - DESCRIPTION, HEADLAMP....8L-18
SWITCH - DESCRIPTION, HORN..........8H-4
SWITCH - DESCRIPTION, IGNITION......19-11
SWITCH - DESCRIPTION, KEY-IN
IGNITION............................19-9
SWITCH - DESCRIPTION, LUMBAR
CONTROL..........................8N-18
SWITCH - DESCRIPTION, MIRROR........8G-2
SWITCH - DESCRIPTION, MULTI-
FUNCTION..........................8L-23
SWITCH - DESCRIPTION, OVERDRIVE . . . 21-190,
21-344
SWITCH - DESCRIPTION, PASSENGER
AIRBAG ON/OFF.....................8O-23
SWITCH - DESCRIPTION, PASSENGER
POWER SEAT.......................8N-20
SWITCH - DESCRIPTION, PASSENGER
SEAT HEATER .......................8G-16
SWITCH - DESCRIPTION, POWER LOCK . . . 8N-8
SWITCH - DESCRIPTION, POWER
MIRROR...........................8N-13
SWITCH - DESCRIPTION, POWER
WINDOW...........................8N-24
SWITCH - DESCRIPTION, PTO..........14-47
SWITCH - DESCRIPTION, SEAT BELT.....8O-28
SWITCH - DESCRIPTION, WASHER
FLUID LEVEL.........................8R-7
SWITCH - DIAGNOSIS AND TESTING,
A/C HIGH PRESSURE.................24-20
SWITCH - DIAGNOSIS AND TESTING,
A/C LOW PRESSURE..................24-21
SWITCH - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-25
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-5
SWITCH - DIAGNOSIS AND TESTING,
DOOR AJAR.........................8L-34
SWITCH - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK................8N-6
SWITCH - DIAGNOSIS AND TESTING,
DRIVER POWER SEAT................8N-17
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP
.........................8L-19
SWITCH - DIAGNOSIS AND TESTING,
HEATED MIRROR
.....................8G-3
SWITCH - DIAGNOSIS AND TESTING,
HEATED SEAT
...................8G-17,8G-8
SWITCH - DIAGNOSIS AND TESTING,
HORN
..............................8H-5
SWITCH - DIAGNOSIS AND TESTING,
IGNITION
...........................19-11SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-25
SWITCH - DIAGNOSIS AND TESTING,
PARK/NEUTRAL POSITION......21-195,21-367
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER POWER SEAT.............8N-20
SWITCH - DIAGNOSIS AND TESTING,
POWER LOCK........................8N-9
SWITCH - DIAGNOSIS AND TESTING,
POWER WINDOW....................8N-24
SWITCH - DIAGNOSIS AND TESTING,
SEAT BELT .........................8O-28
SWITCH - INSTALLATION..............8P-14
SWITCH - INSTALLATION, A/C HIGH
PRESSURE.........................24-20
SWITCH - INSTALLATION, A/C LOW
PRESSURE.........................24-21
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-6
SWITCH - INSTALLATION, DOOR AJAR . . . 8L-35
SWITCH - INSTALLATION, DOOR
CYLINDER LOCK......................8N-6
SWITCH - INSTALLATION, DRIVER
POWER SEAT.......................8N-18
SWITCH - INSTALLATION, DRIVER SEAT
HEATER............................8G-10
SWITCH - INSTALLATION, GLOVE BOX
LAMP..............................8L-36
SWITCH - INSTALLATION, HEADLAMP....8L-20
SWITCH - INSTALLATION, IGNITION......19-12
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-28
SWITCH - INSTALLATION, OVERDRIVE....21-191,
21-345
SWITCH - INSTALLATION, PARK/
NEUTRAL POSITION...........21-195,21-367
SWITCH - INSTALLATION, PASSENGER
AIRBAG ON/OFF.....................8O-25
SWITCH - INSTALLATION, PASSENGER
POWER SEAT.......................8N-21
SWITCH - INSTALLATION, PASSENGER
SEAT HEATER .......................8G-19
SWITCH - INSTALLATION, POWER
MIRROR...........................8N-14
SWITCH - INSTALLATION, POWER
WINDOW...........................8N-26
SWITCH - INSTALLATION, WASHER
FLUID LEVEL.........................8R-8
SWITCH - OPERATION................8P-12
SWITCH - OPERATION, A/C HIGH
PRESSURE.........................24-20
SWITCH - OPERATION, A/C LOW
PRESSURE.........................24-21
SWITCH - OPERATION, BLOWER MOTOR . . 24-24
SWITCH - OPERATION, BRAKE LAMP......8L-4
SWITCH - OPERATION, CLUTCH PEDAL
POSITION...........................6-17
SWITCH - OPERATION, DOOR CYLINDER
LOCK...............................8N-5
SWITCH - OPERATION, DRIVER POWER
SEAT ..............................8N-17
SWITCH - OPERATION, DRIVER SEAT
HEATER.............................8G-8
SWITCH - OPERATION, HEADLAMP......8L-18
SWITCH - OPERATION, HORN...........8H-5
SWITCH - OPERATION, IGNITION........19-11
SWITCH - OPERATION, LUMBAR
CONTROL..........................8N-19
SWITCH - OPERATION, MIRROR.........8G-3
SWITCH - OPERATION, MULTI-FUNCTION
. 8L-24
SWITCH - OPERATION, OVERDRIVE
....21-190,
21-344
SWITCH - OPERATION, PASSENGER
AIRBAG ON/OFF
.....................8O-24
SWITCH - OPERATION, PASSENGER
POWER SEAT
.......................8N-20
SWITCH - OPERATION, PASSENGER
SEAT HEATER
.......................8G-17
SWITCH - OPERATION, POWER LOCK
.....8N-8
SWITCH - OPERATION, POWER MIRROR
. . 8N-13
SWITCH - OPERATION, POWER WINDOW
. 8N-24
SWITCH - OPERATION, PTO
............14-47
SWITCH - OPERATION, SEAT BELT
.......8O-28
SWITCH - OPERATION, WASHER FLUID
LEVEL
..............................8R-7
SWITCH - REMOVAL
..................8P-13
SWITCH - REMOVAL, A/C HIGH
PRESSURE
.........................24-20SWITCH - REMOVAL, A/C LOW
PRESSURE.........................24-21
SWITCH - REMOVAL, BLOWER MOTOR . . . 24-25
SWITCH - REMOVAL, BRAKE LAMP.......8L-5
SWITCH - REMOVAL, DOOR AJAR.......8L-35
SWITCH - REMOVAL, DOOR CYLINDER
LOCK...............................8N-6
SWITCH - REMOVAL, DRIVER POWER
SEAT ..............................8N-18
SWITCH - REMOVAL, DRIVER SEAT
HEATER.............................8G-9
SWITCH - REMOVAL, GLOVE BOX LAMP . . 8L-35
SWITCH - REMOVAL, HEADLAMP........8L-19
SWITCH - REMOVAL, HORN.............8H-5
SWITCH - REMOVAL, IGNITION.........19-12
SWITCH - REMOVAL, LUMBAR
CONTROL..........................8N-19
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-27
SWITCH - REMOVAL, OVERDRIVE......21-191,
21-344
SWITCH - REMOVAL, PARK/NEUTRAL
POSITION...................21-195,21-367
SWITCH - REMOVAL, PASSENGER
AIRBAG ON/OFF.....................8O-24
SWITCH - REMOVAL, PASSENGER
POWER SEAT.......................8N-21
SWITCH - REMOVAL, PASSENGER SEAT
HEATER............................8G-18
SWITCH - REMOVAL, POWER MIRROR . . . 8N-13
SWITCH - REMOVAL, POWER WINDOW . . 8N-25
SWITCH - REMOVAL, WASHER FLUID
LEVEL..............................8R-8
SWITCH AND KEY LOCK CYLINDER -
DIAGNOSIS AND TESTING, IGNITION......19-9
SWITCHES - DESCRIPTION, REMOTE.....8A-14
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-15
SWITCHES - INSTALLATION, REMOTE....8A-16
SWITCHES - OPERATION, REMOTE......8A-15
SWITCHES - REMOVAL, REMOTE........8A-16
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-5
SYMBOLS - DESCRIPTION,
INTERNATIONAL.......................0-1
SYSTEM - CLEANING, BATTERY..........8F-5
SYSTEM - CLEANING, WIPER &
WASHER............................8R-6
SYSTEM - DESCRIPTION, AIR INJECTION . 25-26
SYSTEM - DESCRIPTION, BATTERY.......8F-1
SYSTEM - DESCRIPTION, CHIME
WARNING...........................8B-1
SYSTEM - DESCRIPTION, DIESEL FUEL
DELIVERY..........................14-55
SYSTEM - DESCRIPTION, DIESEL FUEL
INJECTION..........................14-91
SYSTEM - DESCRIPTION, EVAP.........25-32
SYSTEM - DESCRIPTION, FUEL
DELIVERY...........................14-2
SYSTEM - DESCRIPTION, HEATED
MIRROR............................8G-1
SYSTEM - DESCRIPTION, HEATED SEAT . . . 8G-5
SYSTEM - DESCRIPTION, INSTRUMENT
PANEL............................23-105
SYSTEM - DESCRIPTION, METRIC
......Intro.-9
SYSTEM - DESCRIPTION, POWER SEAT
. . 8N-16
SYSTEM - DESCRIPTION, REMOTE
KEYLESS ENTRY
......................8N-2
SYSTEM - DESCRIPTION, SPEED
CONTROL
...........................8P-1
SYSTEM - DESCRIPTION, TURN SIGNAL
& HAZARD WARNING
..................8L-2
SYSTEM - DIAGNOSIS AND TESTING,
AIR IN FUEL
........................14-60
SYSTEM - DIAGNOSIS AND TESTING,
AIRBAG
.............................8O-4
SYSTEM - DIAGNOSIS AND TESTING,
BASE BRAKE
..........................5-5
SYSTEM - DIAGNOSIS AND TESTING,
BATTERY
............................8F-2
SYSTEM - DIAGNOSIS AND TESTING,
CHARGING
..........................8F-25
SYSTEM - DIAGNOSIS AND TESTING,
CHIME WARNING
.....................8B-2
SYSTEM - DIAGNOSIS AND TESTING,
HEATED MIRROR
.....................8G-2
SYSTEM - DIAGNOSIS AND TESTING,
HEATED SEAT
........................8G-6
30 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

SYSTEM - DIAGNOSIS AND TESTING,
POWER LOCK & REMOTE KEYLESS
ENTRY..............................8N-5
SYSTEM - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-16
SYSTEM - DIAGNOSIS AND TESTING,
POWER STEERING....................19-2
SYSTEM - DIAGNOSIS AND TESTING,
STARTING..........................8F-32
SYSTEM - DIAGNOSIS AND TESTING,
TURN SIGNAL & HAZARD WARNING......8L-3
SYSTEM - DIAGNOSIS AND TESTING,
VACUUM...........................24-10
SYSTEM - DIAGNOSIS AND TESTING,
VEHICLE THEFT SECURITY..............8Q-3
SYSTEM - DIAGNOSIS AND TESTING,
WIPER & WASHER....................8R-3
SYSTEM - INSPECTION, BATTERY........8F-6
SYSTEM - INSPECTION, WIPER &
WASHER............................8R-6
SYSTEM - LEAKS - DIAGNOSIS AND
TESTING, CHARGE AIR COOLER.........11-18
SYSTEM - OPERATION, AIR INJECTION . . . 25-28
SYSTEM - OPERATION, BATTERY.........8F-2
SYSTEM - OPERATION, CHIME
WARNING...........................8B-1
SYSTEM - OPERATION, COOLING..........7-4
SYSTEM - OPERATION, FUEL DELIVERY . . . 14-2
SYSTEM - OPERATION, HEATED MIRROR . . 8G-2
SYSTEM - OPERATION, HEATED SEAT.....8G-6
SYSTEM - OPERATION, INSTRUMENT
PANEL..............................23-106
SYSTEM - OPERATION, POWER SEAT....8N-16
SYSTEM - OPERATION, REMOTE
KEYLESS ENTRY......................8N-4
SYSTEM - OPERATION, SPEED CONTROL . . 8P-2
SYSTEM - OPERATION, TURN SIGNAL &
HAZARD WARNING....................8L-2
SYSTEM - SPECIAL TOOLS, AIRBAG......8O-6
SYSTEM - SPECIFICATIONS, TORQUE -
GENERATOR/CHARGING...............8F-27
SYSTEM - SPECIFICATIONS, TORQUE -
STARTING..........................8F-37
SYSTEM - STANDARD PROCEDURE,
BLEEDING ABS BRAKE.................5-36
SYSTEM - STANDARD PROCEDURE,
FLUSHING POWER STEERING...........19-34
SYSTEM - TORQUE, AIR INJECTION......25-29
SYSTEM - TORQUE, EVAP..............25-32
SYSTEM - TORQUE, SPEED CONTROL.....8P-4
SYSTEM 5.9L DIESEL ENGINE -
STANDARD PROCEDURE, DRAINING
COOLING............................7-15
SYSTEM 5.9L DIESEL ENGINE -
STANDARD PROCEDURE, REFILLING
COOLING............................7-16
SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, DRAINING
COOLING............................7-15
SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, REFILLING
COOLING............................7-16
SYSTEM AIR LEAK VACUUM TEST -
DIAGNOSIS AND TESTING, FUEL........14-57
SYSTEM AIRFLOW - DESCRIPTION,
HVAC..............................24-30
SYSTEM CHARGE - STANDARD
PROCEDURE, REFRIGERANT............24-46
SYSTEM CLEANING/REVERSE FLUSHING
- STANDARD PROCEDURE, COOLING......7-17
SYSTEM DIESEL ENGINE - DIAGNOSIS
AND TESTING, COOLING................7-13
SYSTEM EVACUATE - STANDARD
PROCEDURE, REFRIGERANT............24-46
SYSTEM FLOW - 5.9L DIESEL -
DESCRIPTION, COOLING.................7-2
SYSTEM FLOW - 5.9L ENGINE -
DESCRIPTION, COOLING.................7-1
SYSTEM GAS ENGINE - DIAGNOSIS AND
TESTING, COOLING
.....................7-7
SYSTEM LEAKS - DIAGNOSIS AND
TESTING, COOLING
.....................7-5
SYSTEM LEAKS - DIAGNOSIS AND
TESTING, REFRIGERANT
...............24-43
SYSTEM PARTS - STANDARD
PROCEDURES, CLEANING FUEL
.........14-61
SYSTEM PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL
.................14-3SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE, FUEL..........14-3
SYSTEM PRESSURES, DIESEL ENGINES
- FUEL.............................14-62
SYSTEM REQUIREMENTS -
DESCRIPTION, COOLING................24-1
SYSTEM SERVICE EQUIPMENT -
STANDARD PROCEDURE,
REFRIGERANT.......................24-45
SYSTEM SERVICE PORT - DESCRIPTION,
REFRIGERANT........................24-1
SYSTEM SERVICE PORT - OPERATION,
REFRIGERANT........................24-2
SYSTEM, SPECIAL TOOLS - DIESEL
FUEL..............................14-63
SYSTEM, SPECIAL TOOLS - FUEL . . . 14-35,14-4
SYSTEM, SPECIFICATIONS - STARTING . . . 8F-36
SYSTEMS - DESCRIPTION, MONITORED . . 25-17
SYSTEMS, SPECIAL TOOLS - AUDIO......8A-4
SYSTEMS, SPECIAL TOOLS - POWER
DISTRIBUTION....................8W-97-2
TABLE, SPECIFICATIONS - A/C
APPLICATION........................24-7
TACHOMETER - DESCRIPTION..........8J-30
TACHOMETER - OPERATION............8J-30
TAIL LAMP - DESCRIPTION............8L-29
TAIL LAMP - INSTALLATION............8L-30
TAIL LAMP - OPERATION..............8L-29
TAIL LAMP - REMOVAL................8L-29
TAIL LAMP UNIT - INSTALLATION.......8L-30
TAIL LAMP UNIT - REMOVAL...........8L-30
TAILGATE - INSTALLATION.............23-67
TAILGATE - REMOVAL.................23-67
TAILPIPE - 3.9L/5.2L/5.9L - INSPECTION . . 11-11
TAILPIPE - 3.9L/5.2L/5.9L -
INSTALLATION.......................11-11
TAILPIPE - 3.9L/5.2L/5.9L - REMOVAL....11-11
TAILPIPE - 5.9L DIESEL - INSPECTION....11-12
TAILPIPE - 5.9L DIESEL - INSTALLATION . . 11-13
TAILPIPE - 5.9L DIESEL - REMOVAL.....11-12
TAILPIPE - 5.9L HD/8.0L - INSPECTION . . . 11-12
TAILPIPE - 5.9L HD/8.0L -
INSTALLATION.......................11-12
TAILPIPE - 5.9L HD/8.0L - REMOVAL.....11-12
TANK - DESCRIPTION, DIESEL FUEL.....14-82
TANK - DESCRIPTION, FUEL............14-18
TANK - INSTALLATION, FUEL...........14-20
TANK - OPERATION, FUEL..............14-18
TANK - REMOVAL, FUEL...............14-18
TANK CHECK VALVE - DESCRIPTION,
FUEL..............................14-21
TANK CHECK VALVE - INSTALLATION,
FUEL..............................14-23
TANK CHECK VALVE - REMOVAL, FUEL . . . 14-22
TANK MODULE - DESCRIPTION, FUEL....14-82
TANK MODULE - INSTALLATION, FUEL....14-83
TANK MODULE - OPERATION, FUEL......14-82
TANK MODULE - REMOVAL, FUEL.......14-83
TAPE STRIPE - INSTALLATION..........23-89
TAPE STRIPE - REMOVAL..............23-88
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC......................9-36,9-91
TASK MANAGER - DESCRIPTION........25-17
TASK MANAGER - OPERATION..........25-21
TEMP SENSOR - 5.9L - DESCRIPTION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - INSTALLATION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - OPERATION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - REMOVAL,
ENGINE COOLANT.....................7-47
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-12
TEMP SENSOR - INSTALLATION,
AMBIENT..........................8M-13
TEMP SENSOR - OPERATION, AMBIENT . . 8M-12
TEMP SENSOR - REMOVAL, AMBIENT . . . 8M-12
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE
............................8J-18
TEMPERATURE GAUGE - OPERATION,
ENGINE
............................8J-19
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY
...........................8F-27
TEMPERATURE SENSOR - DESCRIPTION,
FUEL
.............................14-104
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION
...............21-218,21-390TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-28
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-27
TEMPERATURE SENSOR - OPERATION,
FUEL.............................14-104
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION...............21-218,21-390
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-27
TEMPORARY - DESCRIPTION, SPARE
TIRE................................22-6
TENSIONERS - 5.9L - DESCRIPTION,
BELT ...............................7-19
TENSIONERS - 5.9L - INSTALLATION,
BELT ...............................7-20
TENSIONERS - 5.9L - OPERATION, BELT . . . 7-19
TENSIONERS - 5.9L - REMOVAL, BELT.....7-19
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-23
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONERS - 8.0L - DESCRIPTION,
BELT ...............................7-20
TENSIONERS - 8.0L - INSTALLATION,
BELT ...............................7-22
TENSIONERS - 8.0L - OPERATION, BELT.....7-21
TENSIONERS - 8.0L - REMOVAL, BELT.....7-21
TERMINAL - INSTALLATION.........8W-01-13
TERMINAL - REMOVAL.............8W-01-13
TEST - DIAGNOSIS AND TESTING, FUEL
INJECTOR..........................14-99
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN................14-2
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE....................14-10
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY......................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE.....................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
SYSTEM AIR LEAK VACUUM............14-57
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE.........21-270,21-98
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-4
TEST - DIAGNOSIS AND TESTING,
VACUUM SUPPLY.....................8P-3
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-11
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE, LOAD . . . 8F-12
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-12
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-5
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION
..........................25-2
TEST MODE - DESCRIPTION, STATE
DISPLAY
............................25-1
TETHER - INSTALLATION, CHILD
.........8O-9
TETHER - REMOVAL, CHILD
.............8O-9
THEFT SECURITY - DESCRIPTION,
VEHICLE
............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE
. . 8Q-2
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE
................8Q-3
THERMOSTAT - 5.9L - DESCRIPTION,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L - INSTALLATION,
ENGINE COOLANT
.....................7-49
THERMOSTAT - 5.9L - OPERATION,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L - REMOVAL,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT
.........7-53
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT
........7-54
BR/BEINDEX 31
Description Group-Page Description Group-Page Description Group-Page

TRANSMITTER BATTERIES - STANDARD
PROCEDURE, REMOTE KEYLESS
ENTRY..............................8N-8
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, RKE...........8N-8
TRAY - DESCRIPTION, BATTERY.........8F-23
TRAY - INSTALLATION, BATTERY........8F-24
TRAY - INSTALLATION, REAR FLOOR
STOWAGE.........................23-121
TRAY - OPERATION, BATTERY..........8F-23
TRAY - REMOVAL, BATTERY............8F-23
TRAY - REMOVAL, REAR FLOOR
STOWAGE.........................23-121
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, A-PILLAR.......23-119
TRIM - INSTALLATION, B-PILLAR.......23-120
TRIM - INSTALLATION, C-PILLAR.......23-128
TRIM - INSTALLATION, DOOR SILL.....23-121
TRIM - INSTALLATION, GLOVE BOX
OPENING UPPER....................23-112
TRIM - INSTALLATION, REAR CLOSURE
PANEL............................23-121
TRIM - REMOVAL, A-PILLAR..........23-119
TRIM - REMOVAL, B-PILLAR..........23-120
TRIM - REMOVAL, C-PILLAR..........23-128
TRIM - REMOVAL, DOOR SILL.........23-121
TRIM - REMOVAL, GLOVE BOX OPENING
UPPER............................23-112
TRIM - REMOVAL, REAR CLOSURE
PANEL............................23-120
TRIM COVER - INSTALLATION, COWL . . . 23-120
TRIM COVER - REMOVAL, COWL.......23-119
TRIM PANEL - INSTALLATION......23-75,23-84
TRIM PANEL - INSTALLATION, QUARTER . 23-128
TRIM PANEL - REMOVAL.........23-75,23-83
TRIM PANEL - REMOVAL, QUARTER....23-128
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-54
TUBE - DIAGNOSIS AND TESTING, FIXED
ORIFICE............................24-54
TUBE - INSTALLATION, A/C ORIFICE......24-54
TUBE - OPERATION, A/C ORIFICE........24-54
TUBE - REMOVAL, A/C ORIFICE.........24-54
TUBES - WITH RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS...................7-78,7-82,7-84
TUBES - WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS...................7-79,7-82,7-85
TURBOCHARGER - CLEANING..........11-16
TURBOCHARGER - DESCRIPTION........11-14
TURBOCHARGER - INSPECTION.........11-16
TURBOCHARGER - INSTALLATION.......11-17
TURBOCHARGER - OPERATION.........11-14
TURBOCHARGER - REMOVAL...........11-15
TURBOCHARGER BOOST PRESSURE -
DIAGNOSIS AND TESTING.............11-13
TURN SIGNAL & HAZARD WARNING
SYSTEM - DESCRIPTION
...............8L-2
TURN SIGNAL & HAZARD WARNING
SYSTEM - DIAGNOSIS AND TESTING
......8L-3
TURN SIGNAL & HAZARD WARNING
SYSTEM - OPERATION
.................8L-2
TURN SIGNAL CANCEL CAM -
DESCRIPTION
.......................8L-31
TURN SIGNAL CANCEL CAM -
OPERATION
.........................8L-31
TURN SIGNAL INDICATOR -
DESCRIPTION
.......................8J-32
TURN SIGNAL INDICATOR - DIAGNOSIS
AND TESTING
.......................8J-32
TURN SIGNAL INDICATOR - OPERATION
. . 8J-32
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT
.............8O-29
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT
.........................8O-29
TURNING LOOP HGT ADJUSTER KNOB -
INSTALLATION
......................8O-30
TURNING LOOP HGT ADJUSTER KNOB -
REMOVAL
..........................8O-30
TWEETER SPEAKER - INSTALLATION,
A-PILLAR
...........................8A-19TWEETER SPEAKER - REMOVAL,
A-PILLAR...........................8A-18
UNDERHOOD LAMP - INSTALLATION.....8L-32
UNDERHOOD LAMP - REMOVAL.........8L-31
UNDERHOOD LAMP UNIT -
INSTALLATION.......................8L-32
UNDERHOOD LAMP UNIT - REMOVAL....8L-32
UNIVERSAL JOINTS - ASSEMBLY,
DOUBLE CARDAN.....................3-11
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
DOUBLE CARDAN.....................3-10
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL JOINTS - INSTALLATION,
SINGLE CARDAN......................3-35
UNIVERSAL JOINTS - REMOVAL, SINGLE
CARDAN............................3-34
UP/DOWN - ADJUSTMENT, FRONT DOOR . 23-70
UPPER - INSTALLATION, LATCH.........23-81
UPPER - INSTALLATION, LATCH
STRIKER...........................23-82
UPPER - REMOVAL, LATCH............23-81
UPPER - REMOVAL, LATCH STRIKER.....23-82
UPPER BALL JOINT - DIAGNOSIS AND
TESTING............................2-12
UPPER CONTROL ARM - INSTALLATION . . . 2-13,
2-19
UPPER CONTROL ARM - REMOVAL . . . 2-13,2-19
UPSHIFT INDICATOR - DESCRIPTION......8J-32
UPSHIFT INDICATOR - OPERATION.......8J-33
USAGE - DESCRIPTION, FASTENER.....Intro.-9
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-10 - DESCRIPTION, 8.0L..............8I-2
V-10 - OPERATION, 8.0L................8I-2
V-10 ENGINE - IGNITION COIL
RESISTANCE, 8.0L.....................8I-4
V-10 ENGINE - SPARK PLUG CABLE
ORDER, 8.0L.........................8I-3
V-8 - OPERATION......................8I-2
V-8 ENGINES - DESCRIPTION...........25-35
V-8 ENGINES - ENGINE FIRING ORDER,
5.9L................................8I-3
V-8 ENGINES - OPERATION............25-35
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-29
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-29
VACUUM LINES - DESCRIPTION.........25-37
VACUUM MOTOR - ASSEMBLY, AXLE......3-34
VACUUM MOTOR - DESCRIPTION, AXLE . . . 3-31
VACUUM MOTOR - DIAGNOSIS AND
TESTING............................3-32
VACUUM MOTOR - DISASSEMBLY, AXLE . . . 3-34
VACUUM MOTOR - INSTALLATION, AXLE . . . 3-34
VACUUM MOTOR - OPERATION, AXLE.....3-31
VACUUM MOTOR - REMOVAL, AXLE......3-34
VACUUM PUMP - 5.9L DIESEL -
DESCRIPTION........................7-33
VACUUM PUMP - 5.9L DIESEL -
INSTALLATION........................7-36
VACUUM PUMP - 5.9L DIESEL -
OPERATION
..........................7-34
VACUUM PUMP - 5.9L DIESEL -
REMOVAL
...........................7-34
VACUUM PUMP OUTPUT - DIAGNOSIS
AND TESTING
........................7-34
VACUUM RESERVOIR - DESCRIPTION
....8P-14
VACUUM RESERVOIR - INSTALLATION
. . . 8P-15
VACUUM RESERVOIR - REMOVAL
.......8P-14
VACUUM SUPPLY TEST - DIAGNOSIS
AND TESTING
........................8P-3
VACUUM SYSTEM - DIAGNOSIS AND
TESTING
...........................24-10
VACUUM TEST - DIAGNOSIS AND
TESTING, FUEL SYSTEM AIR LEAK
.......14-57
VALVE - 5.9L - DIAGNOSIS AND
TESTING, PCV
.......................25-36
VALVE - CLEANING, OIL PRESSURE
RELIEF
.............................9-180
VALVE - DESCRIPTION, COMBINATION
......5-8
VALVE - DESCRIPTION, FUEL TANK
CHECK
.............................14-21VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-46
VALVE - DESCRIPTION, ONE WAY CHECK . 25-31
VALVE - DESCRIPTION, OVERFLOW......14-87
VALVE - DESCRIPTION, TORQUE
CONVERTER DRAINBACK.......21-217,21-390
VALVE - DESCRIPTION, VACUUM CHECK . . 24-28
VALVE - DIAGNOSIS AND TESTING,
COMBINATION.........................5-9
VALVE - DIAGNOSIS AND TESTING,
ONE-WAY CHECK.....................25-31
VALVE - DIAGNOSIS AND TESTING,
OVERFLOW.........................14-87
VALVE - INSPECTION, OIL PRESSURE
RELIEF.............................9-180
VALVE - INSTALLATION, COMBINATION.....5-9
VALVE - INSTALLATION, FUEL TANK
CHECK.............................14-23
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-180
VALVE - INSTALLATION, ONE WAY
CHECK.............................25-31
VALVE - INSTALLATION, OVERFLOW.....14-88
VALVE - INSTALLATION, SPOOL.........19-28
VALVE - INSTALLATION, VACUUM CHECK . 24-29
VALVE - OPERATION, COMBINATION.......5-9
VALVE - OPERATION, HIGH PRESSURE
RELIEF.............................24-47
VALVE - OPERATION, ONE WAY CHECK . . . 25-31
VALVE - OPERATION, OVERFLOW........14-87
VALVE - OPERATION, TORQUE
CONVERTER DRAINBACK.......21-217,21-390
VALVE - OPERATION, VACUUM CHECK....24-28
VALVE - REMOVAL, COMBINATION.........5-9
VALVE - REMOVAL, FUEL TANK CHECK . . . 14-22
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-180
VALVE - REMOVAL, ONE WAY CHECK....25-31
VALVE - REMOVAL, OVERFLOW.........14-88
VALVE - REMOVAL, SPOOL.............19-26
VALVE - REMOVAL, VACUUM CHECK.....24-29
VALVE - STANDARD PROCEDURE,
TORQUE CONVERTER DRAINBACK.....21-217,
21-390
VALVE BODY - ADJUSTMENTS . . . 21-257,21-428
VALVE BODY - ASSEMBLY......21-248,21-420
VALVE BODY - CLEANING.......21-244,21-418
VALVE BODY - DESCRIPTION....21-218,21-391
VALVE BODY - DISASSEMBLY....21-237,21-409
VALVE BODY - INSPECTION.....21-244,21-419
VALVE BODY - INSTALLATION....21-256,21-428
VALVE BODY - OPERATION......21-223,21-394
VALVE BODY - REMOVAL.......21-236,21-407
VALVE CABLE - ADJUSTMENTS,
TRANSMISSION THROTTLE.....21-210,21-382
VALVE CABLE - DESCRIPTION,
THROTTLE...................21-209,21-381
VALVE LASH ADJUSTMENT AND
VERIFICATION - STANDARD
PROCEDURE........................9-141
VALVE SERVICE, STANDARD
PROCEDURE.........................9-80
VALVE SPRINGS - INSTALLATION,
VALVES .............................9-84
VALVE SPRINGS - REMOVAL, VALVES.....9-82
VALVE STEM SEAL - INSTALLATION.......9-83
VALVE STEM SEALS - REMOVAL.........9-82
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST............9-138,9-23,9-80
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST.....................9-26
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST.....................9-25
VALVES AND VALVE SPRINGS -
INSTALLATION........................9-84
VALVES AND VALVE SPRINGS -
REMOVAL...........................9-82
VALVES, GUIDES AND SPRINGS -
STANDARD PROCEDURE
................9-23
VALVES,GUIDES AND SPRINGS -
STANDARD PROCEDURE
...............9-138
VANITY LAMP - INSTALLATION
.........8L-37
VANITY LAMP - REMOVAL
.............8L-37
VAPOR CANISTER - DESCRIPTION
.......25-37
BR/BEINDEX 33
Description Group-Page Description Group-Page Description Group-Page