Side light FIAT PANDA 2009 169 / 2.G Repair Manual

151KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
H4
H4
W5W
PY21W
W5W
PY21W
P21/5W
P21W
P21W
C5W
W5W
C5W
H1
W5W
60/55
60/55
5
21
5
21
21/5
21
21
5
5
5
55
5
D
D
A
B
A
B
B
B
B
C
A
C
E
A
Bulbs Type Power Re. figure 140Main beamDipped beamFront side lightsFront direction indicatorsSide direction indicatorsRear direction indicatorsStop/tail lightsReversing lightsRear fog lightsCeiling lightBoot lightNumber plate lightFog lightsThird stop
135-168 PANDA EN 7-10-2009 14:07 Pagina 151

152KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0089m
fig. 141
F0Z0091m
fig. 143
F0Z0090m
fig. 142
To change the direction indicator bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder D-fig. 142 and remove it (it is pres-
sure-fit);
CHANGING AN EXTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
FRONT LIGHT UNIT
To change the side light bulb, proceed as follows:❒
release the clip A-fig. 141 and remove the cap B;
❒
turn the bulb-holder C-fig. 142 and remove it (it is pres-
sure-fit);
❒
remove the burnt bulb E-fig. 143 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 152

154KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0095m
fig. 147
F0Z0227m
fig. 149
F0Z0604m
fig. 148
FRONT FOG LIGHTS
(for versions/markets where provided)
To change the halogen bulb, proceed as follows:❒
undo the two screws A and B-fig. 149 for fog light fas-
tening on the bumper and take out trim and fog light,
disconnecting the connector;
❒
loosen the cover C-fig. 150 and remove the connec-
tor D;
❒
release the clip E-fig. 151 and remove the bulb F;
❒
refit by reversing the above mentioned operations. SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒
push the lamp lens A-fig. 147 in the car running direc-
tion (it is pressure-fit);
❒
remove the bulb B-fig. 148 and replace it;
❒
remove the lamp lens.
135-168 PANDA EN 7-10-2009 14:07 Pagina 154

158KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0193m
fig. 160
F0Z0213m
fig. 161
F0Z0214m
fig. 162
❒
replace the bulb C-fig. 162 releasing the side contacts,
insert the new bulb and make sure that it is correctly
clamped between the contacts;
❒
close the cap back and refit the lens.
CHANGING AN INTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
CEILING LIGHT
To change the bulbs, proceed as follows:❒
using the screwdriver provided, extract the ceiling light
A-fig. 160 working in the point shown by the arrow;
❒
open the cover B-fig. 161 as shown;
135-168 PANDA EN 7-10-2009 14:07 Pagina 158

159KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0102m
fig. 163
F0Z0103m
fig. 164
BOOT LIGHT
(for versions/markets, where provided)
To change the bulbs, proceed as follows:❒
open the tailgate;
❒
using the screwdriver provided, extract the ceiling light
A-fig. 163 working in the point shown;
❒
open the bulb cover B-fig. 164 and replace the pressure-
fit bulb C;
❒
close again the bulb cover B on the lens;
❒
refit correctly the light pressing one side and then the
other until the locking click is heard.
135-168 PANDA EN 7-10-2009 14:07 Pagina 159

160KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0087m
fig. 165
Refer to the tables on the following pages to identify the
protection fuse.
If a general fuse (MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) cuts in, do not at-
tempt any repair and contact a Fiat Dealership.
WARNING
Before replacing a fuse, make sure the ig-
nition key has been removed and that all
the other services are switched off and/or
disengaged.If the replaced fuse blows again, contact
a Fiat Dealership.
WARNING
Never replace a blown fuse with metal
wires or other recovered material.
WARNING
Never replace a fuse with another of high-
er power: FIRE HAZARD.
WARNING
REPLACING FUSESGENERAL FEATURES fig. 165
Fuses protect the electric system: they cut in (i.e. they
blow) in the event of a failure or improper action on the
system.
When a device does not work, check the efficiency of its
fuse: the filament A must be intact. If it is, replace the blown
fuse with another with the same amperage (same colour).
B undamaged fuse.
C fuse with damaged filament.
To facilitate fuse replacement, use the pliers D hooked
to the fuse-box on the dashboard left-hand side.
135-168 PANDA EN 7-10-2009 14:07 Pagina 160

161KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
FUSE LOCATION
Fuse-boxes are located on the steering wheel left-hand
side fig. 166 and 167.
To gain access to the fuse-boxes, undo the cover F fas-
tening screw E.
G wired control unit.
H body-computer control unit.
D fuse extracting pliers.
The number identifying the electrical component corre-
sponding to each fuse is on the cover back.
fig. 167 fig. 166
F37
18
9
16
F0Z0139m
F0Z0260m
135-168 PANDA EN 7-10-2009 14:07 Pagina 161

176KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0184m
fig. 175 – version 1.1
F0Z0262m
fig. 177 – version 1.3 Multijet
F0Z0106m
fig. 176 – version 1.2-1.2 Euro 5 (C)
IMPORTANT The oil consumption depends on driving
style and the car utilisation conditions.
IMPORTANT After adding or changing the oil, let the en-
gine run for a few seconds and wait a few minutes after
switching it off before checking the level. ENGINE OIL fig. 175 – 176 and 177
Check the oil level a few minutes (about five) after the en-
gine has stopped, with the car parked on level ground.
Check the level is within the MIN. and MAX. marks on the
dipstick B.
The range between the MIN. and MAX. marks corre-
sponds to about 1 litre of oil. If the oil level is close to or
actually below the MIN. mark, pour in the prescribed oil
through the filler A until it reaches the MAX mark. The oil
level must never exceed the MAX mark.
ENGINE OIL CONSUMPTIONThe maximum engine oil consumption is usually 400 grams
every 1000 km.
When the car is new, the engine needs to be run in, there-
fore the engine oil consumption can only be considered
stabilised after the first 5,000 ÷ 6,000 km.
169-190 PANDA EN 7-10-2009 14:14 Pagina 176

177KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCETECHNICAL
SPECIFICATIONS
INDEX
F0Z0182m
fig. 179
F0Z0107m
fig. 178
ENGINE COOLANT fig. 178 and 179
The coolant level must be checked when the engine is cold
and must range between the MIN. and MAX. marks on the
reservoir.
If the level is low, pour slowly a mixture of 50% deminer-
alised water and 50% PARAFLU
UP
of FL Selenia through
the filler neck A until approaching the MAX. level.
A 50-50 mixture of PARAFLU
UP
and demineralised wa-
ter gives freeze protection to −35 °C.
For particularly harsh climate conditions, a mixture of 60%
PARAFLU
UP
and 40% demineralised water is recom-
mended.
When the engine is hot, take care when
working inside the engine compartment to
avoid burns. Remember that when the engine is
hot, the fan may cut in: danger of injury. Scarves,
ties and other loose clothing might be pulled by
moving parts.
WARNING
Never add any oil with different specifica-
tions than those of the existing engine oil. Used engine oil and the replaced oil filter
contain substances that may be dangerous
for the environment. It is advisable to have
oil and filters changed by a Fiat Dealership where
they will be disposed respecting the environment
and according to law prescription.
169-190 PANDA EN 7-10-2009 14:14 Pagina 177

180KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0135m
fig. 183
F0Z0134m
fig. 182
AIR FILTERREPLACEMENT (petrol versions) fig. 182 and 183
Release the clips A, remove the cover front side B
and extract the filtering element C to be replaced.
Brake fluid is poisonous and highly corro-
sive. In the event of accidental contact, im-
mediately wash the affected parts with water
and neutral soap. Then rinse thoroughly. Call a
doctor immediately if swallowed.
WARNING
The symbol
π
on the container indicates
a synthetic brake fluid, distinguishing it
from the mineral kind. Use of a mineral type flu-
ids will damage the special rubber seals of the
braking system beyond repair.WARNING
The symbol πon the container indicates
a synthetic brake fluid, which is different
from a mineral fluid. Use of a mineral-based flu-
id will damage the special rubber seals of the brak-
ing system beyond repair.
WARNING
169-190 PANDA EN 7-10-2009 14:15 Pagina 180