Side light FIAT PANDA 2009 169 / 2.G Workshop Manual

123KNOW
YOUR VEHICLE
SAFETYWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
WARNING LIGHTS AND MESSAGES
WARNING LIGHTS AND MESSAGESGENERAL WARNINGSTurning on of warning light is accompanied by specific mes-
sage and/or by buzzer sound where provided by instru-
ment panel. These indications are concise and brief and
cautionary and as such must not be considered as ex-
haustive and/or alternative to the information contained
in the Owner Handbook, which shall always be read
through carefully and thoroughly. In case of failure indi-
cation, always refer to the specifications contained in this
chapter.
IMPORTANT Failure indications displayed are divided in-
to two categories: very serious and less serious failures.
Very serious failures are indicated by a repeated and pro-
longed warning “cycle”.
Less serious failures are indicated by a limited “warning”
cycle.
The warning cycle of both failure types can be stopped
by pressing the button MODE. The instrument panel warn-
ing light will stay on until the cause of the failure is elimi-
nated.
For messages relevant to the versions equipped with Dua-
logic gearbox, see the attached Supplement.
CORRECT USE
OF THE CAR
LOW BRAKE FLUID (red)
HANDBRAKE ON (red)
Turning the ignition key to MAR the warning light turns
on, but it should go off after a few seconds.
Low brake fluid
The warning light turns on when the level of the brake flu-
id in the reservoir falls below the minimum level due to
a possible leak in the circuit.
On some versions the display shows the dedicated message.
x
If the warning light xturns on when trav-
elling (on certain versions together with
the message on the display) stop the car imme-
diately and contact a Fiat Dealership.
WARNING
Handbrake on
The warning light turns on when the handbrake is on.
On certain versions, if the car is moving the buzzer will al-
so sound.
IMPORTANT If the warning light turns on when travel-
ling, make sure the handbrake is not engaged.
123-134 PANDA EN 7-10-2009 13:49 Pagina 123

132
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
ESP SYSTEM FAILURE (amber)
Turning the ignition key to MAR the warning light
turns on, but it should go off after a few seconds.
If the warning light does not go off or stays on together
with the LED on the button ASR OFF when travelling, con-
tact a Fiat Dealership.
On some versions the display shows the dedicated message.
NOTE The warning light flashing when driving indicates
that the ESP system is active.
á
GENERIC FAILURE INDICATION
(amber)
The warning light turns on in the following cir-
cumstances.
Engine oil pressure sensor failure
The warning light turns on when failure is detected in en-
gine oil pressure sensor. Contact a Fiat Dealership to have
the failure fixed as soon as possible.
Water in diesel fuel filter
See what described for warning light
c.
Inertia fuel cut-off switch tripped
The warning light comes on when the inertia fuel cut-off
switch is triggered. The display shows the dedicated
message.
è
EXTERNAL LIGHT FAILURE (amber)
The warning light will come on (some versions
only) when a failure to one of the following lights
is detected:
– side lights;
– brake lights (third brake light excluded);
– rear fog lights;
– direction indicators;
– number plate lights.
The failure referring to these lights could be: one or more
blown bulbs, a blown protection fuse or an electric con-
nection cut-off.
The display shows the dedicated message.
W
REAR FOG LIGHTS (amber)
The warning light turns on when the rear fog
lights are turned on.
4
HEATED REAR WINDOW (amber)
The warning light turns on when switching the
heated rear window on.
(
123-134 PANDA EN 7-10-2009 13:49 Pagina 132

133KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CARWARNING LIGHTS
AND MESSAGESIN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
FRONT FOG LIGHTS (green)
The warning light comes on when the front fog
lights are turned on. HILL HOLDER FAILURE (amber)
Turning the ignition key to
MAR
the warning light
turns on, but it should go off after a few
seconds.
The warning light will turn on when the Hill Holder sys-
tem is faulty. In this case, contact a Fiat Dealership as soon
as possible.
On some versions the display shows the dedicated message.
SIDE/TAIL LIGHTS AND LOW BEAMS
(green) FOLLOW ME HOME (green)
Side/tail lights and low beams
The warning light comes on when side/tail lights or low
beams are turned on.
Follow me home
The warning light will come when this device is active (see
“Follow me home” in chapter “Know your vehicle”).
The display shows the dedicated message.
*3
LEFT-HAND DIRECTION INDICATOR
(green - blinking)
The warning light turns on when the direction in-
dicator control lever is moved downwards or, together
with the right indicator, when the hazard warning light but-
ton is pressed.
RIGHT-HAND DIRECTION INDICA-
TOR (green - blinking)
The warning light turns on when the direction in-
dicator control lever is moved upwards or, together with
the left indicator, when the hazard light button is pressed.
5FD
123-134 PANDA EN 7-10-2009 13:49 Pagina 133

134
KNOW YOUR
VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
LIMITED RANGE (versions with reconfigurable
multifunction display)
The display will show the dedicated message to warn the
driver that the driving range is less than 50 km.
ASR SYSTEM (versions with reconfigurable mul-
tifunction display)
The ASR system can be turned off by pressing the button
ASR OFF.
The display will show the dedicated message to warn the
driver that the system is off; at the same time the button
LED will come on.
Pressing again the button ASR OFF, the button LED will
turn off and the display will show the dedicated message
to warn the driver that the system is on again. POSSIBLE PRESENCE OF ICE ON THE ROAD
(versions with reconfigurable multifunction
display)
When the outside temperature reaches or falls below
3 °C the outside temperature indication flashes to warn
the driver about the possible presence of ice on the road.
The display shows the dedicated message.
SPEED LIMIT EXCEEDED
The display will show the dedicated message when the car
exceeds the set speed limit (see “Multifunction Display” in
chapter “Know your vehicle”).“DUALDRIVE” ELECTRIC POWER
STEERING ACTIVATION (green)
The wording “CITY” will turn on when engag-
ing the “Dualdrive” electric power steering by pressing the
relevant button. Press the button again to turn the “CITY”
wording off.
MAIN BEAM HEADLIGHTS (blue)
The warning light comes on when the main
beams are turned on.
CITY1
123-134 PANDA EN 7-10-2009 13:49 Pagina 134

139KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0078m
fig. 122
F0Z0695m
fig. 123
❒
to remove the wheel cup secured by spring, use the
screwdriver provided, levering on the three notches
present on the outer circumference;
❒
loosen by about one turn the bolts on the wheel to be
replaced, using the tool E-fig. 123;
❒
turn the jack crank to open it partially;
❒
position the jack near the wheel to be repaired at the
reference point
O
on the side member;
❒
loosen the clamping device B-fig. 122;
❒
take out the tool container C and take it near to the
wheel to be changed;
❒
take the space-saver wheel D;
135-168 PANDA EN 7-10-2009 14:06 Pagina 139

140KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0173m
fig. 124
F0Z0233m
fig. 125
❒
remove the wheel cup (if provided) after loosening the
three fastening bolts and then undo the fourth bolt
L-fig. 125 and remove the wheel;
❒
ensure that the groove F-fig. 124 of the jack is well fit-
ted onto the tab G of the side member;
❒
warn bystanders that the car is about to be lifted. They
must stay clear and not touch the car until it is back
on the ground;
❒
fit the handle H into the jack device
Iand lift the car un-
til the wheel to be changed is some centimetres off the
ground. When turning the jack handle make sure that
it can be used easily and take care not to scrape your
hand against the ground. Even the moving components
of the jack (screws and joints) can cause injuries: avoid
to touch them. Clean off any lubricating grease;
135-168 PANDA EN 7-10-2009 14:06 Pagina 140

144KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0670m
fig. 133
Hand the leaflet over to the personnel
charged to manage the tyre treated using
the tyre repair kit.
WARNING
In the case of a puncture, caused by a for-
eign body, tyres that have suffered damage
up to a maximum diameter of 4 mm on the
tread or the shoulder can be repaired.
❒
instruction brochure (see fig. 133), to be used for prompt
and proper use of the quick repair kit and to be then
handed to the personnel charged with handling the treat-
ed tyre;
❒
a compressor D-fig. 132 including gauge and connec-
tions, in the container;
❒
a pair of protection gloves located in the side space of
the compressor;
❒
adapters for inflating different elements.
In the tool bag you also find the screwdriver, the tow ring
and the jack.
F0Z0607m
fig. 132
135-168 PANDA EN 7-10-2009 14:06 Pagina 144

145KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Tyre side wall holes and punctures cannot
be repaired. Do not use the quick repair
kit if the tyre is damaged as the vehicle has run on
a flat tyre.
WARNING
If the wheel rim is damaged (bad groove
distortion causing air leakage) it cannot
be repaired. Do not remove the foreign body
(screws or nails) from the tyre.
WARNING
PLEASE REMEMBER THAT:
The sealing fluid of the quick tyre repair kit is effective with
external temperatures between −20 °C and +50 °C.
The sealing fluid has a limited life.
Never not operate the compressor for
longer than 20 consecutive minutes. Risk
of overheating. The quick repair kit is not suitable
for definitive repairs. Tyres may only be repaired
temporarily.
WARNING
The bottle contains ethylene glycol. It con-
tains latex that might cause allergic reac-
tions. It is harmful if swallowed. It is irritant for the
eyes in case of contact. It may cause sensitisation
by inhalation or contact. Avoid contact with your
eyes, skin and clothes. In the event of contact, wash
immediately with plenty of water. Do not induce
vomit if swallowed. Rinse your mouth and drink
plenty of water. Call a doctor immediately. Keep
away from children. The product must not be used
by asthmatics. Do not inhale the vapours during in-
sertion and suction. Call a doctor immediately if al-
lergic reactions are noted. Store the bottle in the
specific compartment, away from sources of heat.
The sealant fluid has a limited life.
WARNING
135-168 PANDA EN 7-10-2009 14:07 Pagina 145

146KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0697m
fig. 134
F0Z0672m
fig. 135
❒
make sure that the compressor switch D-fig. 135 is in
position 0 (off), start the engine, fit the plug E-fig. 136
in the 12 V-socket in the central tunnel and operate the
compressor turning the switch D-fig. 135 to position I
(on). Inflate the tyre at the pressure value specified in
paragraph “Inflation pressure” in chapter “Technical
specifications”.
For a more accurate reading, check pressure gauge
F-fig. 135 with the compressor off;
❒
if after five minutes it is still impossible to reach at least
1.5 bar, disengage the compressor from the valve and
current socket, then move the car forth for approx. ten
metres in order to distribute the sealing fluid inside
the tyre evenly, then repeat the inflation operation;
INFLATING PROCEDURE
Replace the bottle containing out of date
sealant fluid. Dispose of the bottle and the
sealant liquid properly. Dispose according
to the national and local regulations in force.Put on the protection gloves provided to-
gether with quick tyre repair kit.
WARNING
❒
Ensure that the handbrake is engaged. Remove the tyre
valve cap, extract the flexible filler tube A-fig. 134 and
fasten the ring B onto the tyre valve;
135-168 PANDA EN 7-10-2009 14:07 Pagina 146

149KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CHANGING A BULBGENERAL INSTRUCTIONS❒
Before changing a bulb check the contacts for oxidation;
❒
burnt bulbs must be replaced by others of the same type
and power;
❒
always check the headlight beam aiming after changing
a bulb;
❒
when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing fus-
es” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or
do not take the system technical specifications in-
to account can cause malfunctions leading to the
risk of fire.
WARNING
Halogen bulbs contain gas under pressure;
if they break, glass fragments may be dis-
persed.
WARNING
When handling halogen bulbs, only touch
the metal part. If the transparent bulb is
touched with the fingers, its lighting inten-
sity is reduced and life of the bulb may be com-
promised. In the event of accidental contact, wipe
the bulb with a cloth moistened with alcohol
and leave it to dry.
IMPORTANT The headlight inner surface might be slight-
ly misted: this should not be considered irregular rather
a natural phenomenon due to low temperature and the air
humidity level. Misting will disappear as soon as the head-
lights are turned on. The presence of drops inside the
headlights indicates infiltration of water. Contact a Fiat
Dealership.
Where possible, it is advisable to have bulbs
changed at a Fiat Dealership. The correct
operation and aiming of the outer lights are
absolutely important to the safety of the car and
its passengers and the subject of specific laws about
road traffic.
135-168 PANDA EN 7-10-2009 14:07 Pagina 149