lock FORD AEROSTAR 1997 1.G Owner's Guide

136
*
[SS26801(ALL)02/96]
6. Before placing the child in the child seat,
forcibly tilt the seat from side to side, and
tug it forward to make sure that the seat is
securely held in place. See Figure 7.
[SS26900(ALL)01/96]
half page art:0011244-A
Checking that the seat is secure
*
[SS27000(ALL)02/96]
7. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode. See
Figure 8.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

137 [SS27100(ALL)01/96]
half page art:0011245-B
Checking the retractor
*
[SS27201(ALL)01/96]
8. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SS27205(ALL)01/96]
NOTE: To remove the retractor from automatic
lock mode, allow seat belt to retract
fully to its stowed position and the
retractor will automatically switch back
to the vehicle sensitive locking mode
for normal adult usage.
*
[SS27210(ALL)03/96]
RWARNING
Carefully follow all of the manufacturer's
instructions included with the safety seat
you put in your vehicle. If you do not
install and use the safety seat properly,
the child may be injured in a sudden stop
or collision.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

138
[SS27300(ALL)01/96]
Installing Child Safety Seats at
the Rear Center Seating Position
with Locking Adjustable Lap Belt
[SS27350(ALL)01/96]
DO NOT install a forward-facing child safety
seat in the third row center seating position.
Forward-facing seats must be installed with a
lap/shoulder belt, or a lap belt and top tether
strap.
[SS27400(ALL)01/96]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue toward the loose
end of webbing.
*
[SS27450(ALL)01/96]
2. Place the child safety seat in the center
seating position.
*
[SS27500(ALL)01/96]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
*
[SS27550(ALL)01/96]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
*
[SS27600(ALL)01/96]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
*
[SS27650(ALL)01/96]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

140 [SS27812(ALL)01/96]Until a floor anchor is installed, follow these
steps to install a tethered child safety seat in the
front seat:
[SS27814(ALL)01/96]
1. Buckle the lap/shoulder belt in the seat
directly behind the front passenger seat.
[SS27816(ALL)01/96]
2. Pull all the stored belt out of the rear seat
belt retractor to switch the retractor to
automatic locking mode.
*
[SS27818(ALL)03/96]
3. Let the retractor wind up the slack from the
lap/shoulder belt. A clicking sound should
be heard as the belt retracts, indicating that
the retractor is in automatic locking mode.
[SS27820(ALL)01/96]
4. Install the child safety seat in the right front
seat. Refer to the previous section on
Installing Child Safety Seats. Hook the tether
strap around the webbing near the center of
the shoulder portion of the lap/shoulder
belt.
*
[SS27822(ALL)05/96]
5. Tighten the tether strap.
[SS27824(ALL)01/96]
Until floor-mounted tether anchors are installed,
tether straps of child safety seats in the second
row may be anchored to lap/shoulder belts for
the third row, following the five steps above, or
to the tongue of the third row lap belt.
*
[SS27830(ALL)01/96]
RWARNING
Follow these precautions to decrease the
chance of injury in an accident.
*
[SS27840(ALL)01/96]
RWARNING
If the anchor bolt(s) is ever removed, the
hole(s) in the floor must be sealed to
prevent the possibility of exhaust fumes
entering the passenger compartment.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

148 [SS30360(ALL)01/96]
half page art:0095056-AFigure 9: Checking for securely latched buckle and locked
retractor
[SS30370(ALL)01/96]
11. If the shoulder belts are pulled too tight,
pull on the lap and shoulder belts cinch
release strap to loosen the shoulder belts on
the child's shoulders. Refer to Figure 4. Then
retighten the lap and shoulder adjustment
belt per Step 10 above.
*
[SS30380(ALL)08/95]
To remove the child from the built-in child
seat:
[SS30390(ALL)01/96]
1. Squeeze the tabs on the top and bottom of
the chest clip and pull the halves apart to
open the chest clip. Refer to Figure 8.
*
[SS30400(ALL)08/95]
2. Press the release button on the crotch safety
belt buckle.
[SS30410(ALL)01/96]
3. Slide the shoulder belts off the child's
shoulders and remove the child. Refer to
Figure 6.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

149 [SS30420(ALL)04/96]
To stow the built-in child seat:
[SS30430(ALL)01/96]
1. Return the child seat cushion to the upright
position and lift the protector flap toward
the headrest.
[SS30440(ALL)01/96]
2. Fasten the snaps securely.
[SS30450(ALL)01/96]
3. Pull on the headrest release strap and rotate
the headrest downward until it latches
against the child seat cushion.
[SS30460(ALL)01/96]
RWARNING
Always fasten the protector flap snaps
when stowing your child seats to prevent
the child seat cushion from rotating
forward in a collision.
[SS30470(ALL)01/96]
The seat can now be used by an adult.
*
[SS30480(ALL)01/96]
Inspection after a collision
*
[SS30490(ALL)01/96]
RWARNING
All built-in child restraints, including
seats, buckles, retractors, seat latches,
interlocks, and attaching hardware should
be inspected by a qualified dealer
technician after any collision.
*
[SS30495(ALL)01/96]
If the child seat was in use during a collision,
Ford recommends replacing it. However, if the
collision was minor and a qualified technician
finds that the child restraints do not show
damage and continue to operate properly, they
do not need to be replaced. If there is any
bending of the vehicle seatback or seat structure,
it should also be replaced. Built-in child seats
not in use during a collision should also be
inspected and replaced if either damage or
improper operation is noted.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

155
*
[TO06575(ALL)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO06601(ALL)01/96]
After starting, allow the engine to idle for a few
seconds before driving away.
%*
[TO06625(ALL)05/96]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[TO06627(ALL)05/96]
1. Apply the parking brake.
*
[TO06629(ALL)05/96]
2. Remove the key.
*
[TO06631(ALL)05/96]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[TO06633(ALL)05/96]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[TO06635(ALL)05/96]
5. Start the vehicle.
*
[TO06637(ALL)05/96]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledRoadside Emergenciesin
this Owner Guide for instructions on checking
and replacing fuses.
*
[TO06640(ALL)05/96]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

157
*
[TO07450(ALL)01/96]
RWARNING
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine
compartment and exhaust system, which
can start a fire.
*
[TO07500(ALL)01/96]
If you consistently start your vehicle in subzero
temperatures, use an engine block heater (if
your vehicle has this option).
%*
[TO07600(ALL)01/96]
Engine Block Heater (If equipped)
*
[TO07700(ALL)01/96]
Engine block heaters are strongly recommended
if you live in a region where temperatures reach
-10ÊF (-23ÊC) orbelow. An engine block heater
warms the engine coolant, which improves
starting, warms up the engine faster, and allows
the heater-defrost system to respond quickly.
*
[TO08000(ALL)01/96]
RWARNING
To prevent electrical shock, do not use
your heater with ungrounded electrical
systems or two-pronged (cheater) adapters.
*
[TO08100(ALL)01/96]
For best results, plug the heater in at least three
hours before you start your vehicle. Using the
heater for longer than three hours will not
damage the engine, so you can plug it in at
night to start your vehicle the following
morning.
*
[TO08150(ALL)01/96]
NOTE: Be sure to disconnect the engine block
heater before driving your vehicle.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

161 [TO10800(ALL)01/96]
q
AIR CONDITIONING Ð Set the fan speed
knob at MEDIUM or HIGH, the function
selector knob on NORM A/C or MAX A/C
and the temperature control knob on any
desired position.
*
[TO12000(ALL)03/96]
Removing the Key From the
Ignition
*
[TO12100(ALL)03/96]
1. Put the gearshift in P (Park).
*
[TO12200(ALL)03/96]
2. Set the parking brake fully before removing
your foot from the service brake. (This will
avoid ªbindingº or ªloadingº the park gear
if you park on a grade.)
*
[TO12300(ALL)03/96]
3. Turn the ignition key to LOCK.
*
[TO12400(ALL)03/96]
4. Remove the key.
*
[TO12500(ALL)05/96]
RWARNING
Always set the parking brake fully and
make sure the gearshift is latched in P
(Park). Turn off the ignition whenever you
leave your vehicle.
*
[TO12600(ALL)03/96]
RWARNING
Do not leave children, unreliable adults,
or pets unattended in your vehicle.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

164 %
*
[GF00750(ALL)01/96]
Rear Anti-lock Brakes
[GF00800(ALL)01/96]
Your vehicle is equipped with a rear Anti-lock
Brake System (ABS). This system prevents at
least one and often both rear wheels from
completely locking up when the brakes are
applied in a panic stop, for example.
*
[GF00850(ALL)01/96]
Even with the Anti-lock Brake System, you
should be careful when braking. Front brake
lock up on any surface, even on smooth
pavement causes loss of steering control. Heavy
braking on roads with loose surfaces such as
snow or gravel, or severe pavement irregularities
could also cause you to lose steering control of
your vehicle.
*
[GF00900(ALL)03/96]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[GF00950(ALL)03/96]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
%*
[GF01000(ALL)03/96]
If Brakes Do Not Grip Well or Pedal is
ªLowº
%*
[GF01100(ALL)03/96]
If brakes do not grip well, it may indicate the
rear drum brakes need adjustment. To do this,
drive the vehicle in reverse at 5 mph (8 km/h)
on level, dry pavement. Stop the vehicle by
firmly applying the brakes. Repeat this
procedure four or five times.
File:09cpgfa.ex
Update:Wed Jun 5 12:04:06 1996