lock FORD AEROSTAR 1997 1.G Owner's Manual

105 [SS00375(ALL)01/96]
half page art:0095041-A
Installation and removal of the second and third passenger
bed and bench seat
*
[SS00380(ALL)05/96]
RWARNING
Never adjust the driver's seat or seatback
when the vehicle is moving.
*
[SS00385(ALL)01/96]
RWARNING
Always latch the vehicle seat to the floor,
whether the seat is occupied or empty. If
not latched, the seat may cause injury
during a sudden stop.
*
[SS00390(ALL)01/96]
RWARNING
Before using the seat, make sure that the
latch hooks are securely locked around the
floor pins.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

106 % [SS00395(ALL)04/96]Seat/bed conversion (If Equipped)
[SS00400(ALL)01/96]
Vehicles equipped with the seat/bed can be
either a two passenger or three passenger seat.
[SS00405(ALL)04/96]
To convert the seat/bed to a bed:
[SS00410(ALL)01/96]
1. Pull up the release lever located on right
hand side of the seat, and at the same time
push the seatback rearward.
[SS00415(ALL)01/96]
2. Push the top of the seatback down until it
latches.
[SS00420(ALL)01/96]
The two passenger seat cushion will move
forward when going from the seat to the bed
position.
[SS00425(ALL)04/96]
To convert the bed to a seat:
[SS00430(ALL)04/96]
1. While in front of the seat, pull the release
lever up and at the same time pull the
seatback up. Raise the seatback to the full
upright and locked position.
*
[SS00435(ALL)01/96]
2. Make sure the safety belts are free and
available for use.
[SS00440(ALL)04/96]
RWARNING
The seat/bed should not be occupied
while the vehicle is moving unless it is in
the upright, fully-latched position.
%*
[SS00445(ALL)05/96]
Using the Lumbar Support and Side
Bolsters
[SS00450(ALL)05/96]
Adjusting the Lumbar Support (If equipped)
[SS00455(ALL)05/96]
To adjust the lumbar pad, turn the knob
clockwise or counterclockwise.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

110
*
[SS02700(ALL)02/96]
RWARNING
Never let a passenger hold a child on his
or her lap while the vehicle is moving.
The passenger cannot protect the child
from injury in a collision.
*
[SS02900(ALL)02/96]
RWARNING
Lock the doors of your vehicle before
driving to lessen the risk of the door
coming open in a collision.
%
*
[SS03000(ALL)02/96]
Combination Lap and Shoulder
Belts
*
[SS03200(ALL)02/96]
While your vehicle is in motion, the combination
lap and shoulder belt adjusts to your movement.
However, if you brake hard, turn hard, or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap/shoulder belt locks
and helps reduce your forward movement.
*
[SS03400(ALL)01/96]
After you get into your vehicle, close the door
and lock it. Then adjust the seat to the position
that suits you best.
*
[SS03500(ALL)02/96]
Pull the combination lap/shoulder belt from the
retractor so that the shoulder portion of the belt
crosses your shoulder and chest. Be sure the belt
is not twisted. If it is, remove the twist. Insert
the belt tongue into the proper buckle until you
hear a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

111
*
[SS03600(ALL)01/96]
quarter page art:0010018-B
Fastening the front seat combination lap and shoulder belt
[SS03650(ALL)04/96]
NOTE: Be sure to read and understand
Important Safety Belt Informationat
the beginning of this chapter.
[SS03800(ALL)01/96]
one third page art:0095046-A
Unfastening the combination lap and shoulder belts Ð
front and rear outboard seating positions
*
[SS03900(ALL)02/96]
While the belt retracts, guide the tongue to its
original position to prevent it from striking you
or the vehicle.
*
[SS04000(ALL)01/96]
Safety Belts for Front Outboard Passenger
and Rear Outboard Seating Positions
*
[SS04210(ALL)01/96]
Your vehicle is equipped with a dual locking
mode retractor on theshoulderbelt portion of
the combination lap/shoulder safety belt for the
front seat outboard passenger and rear outboard
passengers.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

112
*
[SS04220(ALL)02/96]
Dual locking mode retractors operate in two
ways:
*
[SS04230(ALL)02/96]
Vehicle sensitive (emergency) locking mode
*
[SS04240(ALL)02/96]
In this operating mode, the shoulder belt
retractor will allow the occupant freedom of
movement, locking tight only on hard braking,
hard cornering or impacts of approximately
5 mph (8 km/h) or more. The retractor can also
be made to lock by pulling the belt out quickly.
%*
[SS04250(ALL)02/96]
Automatic locking mode
*
[SS04260(ALL)01/96]
In this operating mode, the shoulder belt
retractor will be automatically locked and will
remain locked when the combination
lap/shoulder safety belt is buckled, and does not
allow the occupant freedom of movement. This
mode provides the following:
*
[SS04270(ALL)01/96]
q
A tight lap/shoulder belt on the occupant.
*
[SS04280(ALL)01/96]
q
Child safety seat installation.
*
[SS04300(ALL)01/96]
This modemust be usedwhen installing a child
safety seat on the front passenger seat and rear
outboard seats where dual locking retractors are
provided.
*
[SS04310(ALL)01/96]
To switch the retractor from the emergency
locking mode to the automatic locking mode,
perform the following steps:
*
[SS04320(ALL)02/96]
1. Buckle the lap/shoulder combination belt.
*
[SS04330(ALL)01/96]
2. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and, when allowed to retract, a
clicking sound is heard. At this time, the belt
retractor is in the automatic locking mode
(child restraint mode).
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

113
*
[SS04340(ALL)02/96]
3. A clicking sound will continue to be heard
as the belt is allowed to retract. This
indicates that the retractor is in the
automatic locking mode.
*
[SS04350(ALL)02/96]
NOTE: When the combination lap/shoulder
belt is unbuckled and allowed to
retract completely, the retractor will
switch to the vehicle sensitive
(emergency) locking mode. See the
detailed instructions underSafety Seats
for Childrenin this chapter.
[SS04375(ALL)01/96]
Two Passenger Bench or Bedseat
(If Equipped)
[SS04400(ALL)04/96]
In addition to anchorages in the floor and roof
structures, some rear safety belts have a
detachable anchor mounted to the outboard side
of the rear seats. This should remain attached,
except when removing the rear seats.
[SS04800(ALL)01/96]
Disengaging rear seat safety belts for seat
removal
[SS04850(ALL)01/96]
In order to remove the rear seat, the safety belt
must be disengaged from the seat. To disengage
the safety belt from the seat, insert a key or
small screwdriver into the slot provided on the
detachable anchor. Then lift upward.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

117
*
[SS07500(ALL)01/96]
Pull the belt across your hips andinsert the
tongue into the correct buckleon your seat
until you hear a snap and feel it lock. Make sure
the buckle is securely fastened.
%*
[SS07700(ALL)01/96]
If you need to lengthen the belt, unfasten it and
tip the belt tongue at a right angle to the belt.
Pull the belt tongue over your lap until it
reaches the buckle.
*
[SS07800(ALL)01/96]
If you need to shorten the belt, pull on the loose
end of the webbing until the belt fits snugly.
[SS08600(ALL)05/96]
To unfasten the belt, push the release button on
the buckle. This allows the tongue to unlatch
from the buckle.
*
[SS08800(ALL)05/96]
RWARNING
The lap belts should fit snugly and as low
as possible around the hips, not around
the waist.
%*
[SS09600(ALL)02/96]
Safety Belt Extension Assembly
*
[SS09700(ALL)01/96]
For some people, the safety belt may be too
short even when it is fully extended. You can
add about eight inches (20 cm) to the belt length
with a safety belt extension assembly (part
number 611C22). Safety belt extensions are
available at no cost from your dealer.
*
[SS09750(ALL)01/96]
Use only extensions manufactured by the same
supplier as the safety belt. Manufacturer
identification is located at the end of the
webbing on the label. Also, use the safety belt
extension only if the safety belt is too short for
you when fully extended. Do not use extension
to change the fit of the shoulder belt across the
torso.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

130 %
*
[SS15900(ALL)01/96]
Safety Seats for Children
*
[SS16000(ALL)01/96]
Use a safety seat that is recommended for the
size and weight of the child. Always follow the
safety seat manufacturer's instructions when
installing and using the safety seat.
[SS16005(ALL)01/96]
Most child safety seats can be used in this
vehicle only in vehicle seating positions with
lap/shoulder belts. Any booster-type seat that
places the vehicle's lap belt or shoulder belt
around a shield above and ahead of the child's
hips should not be used in this vehicle. This
type of safety seat could cause injury by tipping
over the front edge of the vehicle seat during a
collision.
[SS16010(ALL)04/96]
RWARNING
The following instructions MUST BE
FOLLOWED to reduce risk of injury from
a safety seat tipping too far forward in a
severe crash.
[SS16012(ALL)01/96]
Install forward-facing child safety seats only in
vehicle seating positions equipped with
lap/shoulder belts. Forward-facing convertible
safety seats can be used in the center of the
three-passenger second row bench seat only if a
top tether strap is used. Ford recommends
placing forward-facing safety seats in the second
row and using safetey seats with top tether
straps for added protection.
[SS16015(ALL)01/96]
For more information on top tether straps see
Attaching Safety Seats With Tether Strapsin this
chapter.
*
[SS16025(ALL)05/96]
When installing a child safety seat, be sure to
use the correct safety belt buckle for that seating
position, and make sure the tongue is securely
fastened in the buckle. For a shoulder/lap belt
combination with a sliding tongue, make sure
the retractor is in the automatic locking mode.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

131
*
[SS16090(ALL)05/96]
All child restraint systems are designed to be
secured in vehicle seats by lap belts or by the
lap portion of a lap-shoulder belt.
*
[SS16100(ALL)03/96]
RWARNING
If you do not properly secure the safety
seat, the child occupying the seat may be
injured during a collision or sudden stop.
An unsecured safety seat could also injure
other passengers.
*
[SS16125(ALL)03/96]
RWARNING
Carefully follow all of the manufacturer's
instructions included with the safety seat
you put in your vehicle. If you do not
install and use the safety seat properly,
the child may be injured in a sudden stop
or collision.
[SS25601(ALL)01/96]
Installing Child Safety Seats in
the Front Seat and Rear Outboard
Seating Positions
[SS25650(ALL)01/96]
Your vehicle is equipped with a dual locking
mode retractor on the shoulder belt portion of
the combination lap/shoulder safety belt for the
right front seat passenger and rear outboard
passengers.
[SS25701(ALL)01/96]
If you choose to install a child safety seat or
infant carrier in these seating positions:
[SS25750(ALL)01/96]
1. Position the child seat on the seat of the
vehicle. In the front seat, adjust the vehicle
seat as far rearward as possible.
[SS25801(ALL)01/96]
2. Pull down on the shoulder belt, then grasp
the shoulder belt and lap belt together. See
Figure 1.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

134
*
[SS26301(ALL)01/96]
4. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and a click is heard. At this time,
the retractor is in the automatic locking
mode (child seat restraint mode). See
Figure 4.
[SS26401(ALL)01/96]
half page art:0011241-A
Setting the retractor to automatic locking mode
*
[SS26500(ALL)02/96]
5. Allow the belt to retract. Pull up on the
shoulder webbing. A clicking sound will be
heard as the belt retracts. This indicates the
retractor is in the automatic locking mode.
Push down on the child seat while you pull
up on the belt to remove any slack in the
belt. See Figures 5 and 6.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996