torque FORD FIESTA 2007 Owner's Manual

211 -03-2 Steering Linkage 21 1-03-2
SPECIFICATIONS
Torque Specifications
sl lb-ft Ib-in /"
I Tie-rod to steering gear I 110 I 81 I - 1 'c..
I ~ie-rod end locknut
I Tie-rod end retaining nut 1 48 I 35 I - I
-
2006.0 Fiesta 1212006 GI 05649en
procarmanuals.com

211 -03-9 Steering Linkage 21 1-03-9
REMOVAL AND INSTALLATION
ATO counter the extensive torque forces 3. Using a suitable pair of pincers, install a new
required to remove the tie-rod, clamp the steering
gear boot inner clamp.
steering rack teeth in a suitable vise. Do not
clamp the steering gear body.
Secure the steering rack in a vise and using
a suitable pipe wrench remove the tie-rod.
Installation
1. Using the special tool, install the tie-rod.
4. N0TE:Make sure the steering gear boot outer
clamp is located over the recess in the
tie-rod.
Using a suitable pair of pincers, install a new
steering gear boot outer clamp.
5. N0TE:lnstall the tie-rod end using the same
number of turns used to remove
it.
2. N0TE:Lubricate the steering gear boot. Install the tie-rod end and the
tie tie-rod end
locknut.
Install a new steering gear boot.
2006.0 Fiesta 1212006 G91976en
procarmanuals.com

2 1 I -04-2 Steering Column 21 1 -04-2
SPECIFICATIONS
Torque Specifications
Description
Nm I b-ft lb-in
Steering wheel retaining bolt
I Steering column retaining nuts I 24 I 18 I - I
Steering column shaft to steering gear pinion
retaining bolt
2006.0 Fiesta 1212006 GI 05652en
procarmanuals.com

303-00-31 Engine System - General Information 303-00-31
DIAGNOSIS AND TESTING
11. Connect the oil pressure switch electrical
connector to the oil pressure switch.
12 Lower the vehicle.
Valve train analysis - static (engine off)
Remove the valve cover.
Check all components of the valve train for damage
and wear. Make sure that only original components
are installed and that all nuts and bolts are
tightened to the specified torque.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-39 Engine System - General Information 303-00-39
GENERAL PROCEDURES
Cylinder Bore Taper
1. N0TE:The main bearing caps or lower
crankcase must be in place and tightened to
the specified torque; however, the bearing
shells should not be installed.
Measure the cylinder bore with an internal
micrometer.
Carry out the measurements in different
directions and at different heights to
determine if there is any out-of-roundness or
tapering.
If the measurement is out of the specified
range, install a new block or hone out the
cylinder block (if
aplicable/allowed).
2006.0 Fiesta 1212006 GI 7628en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)l184L
Duratec-1 6V (Sigma)/186L Duratec-1 6V (Sigma)
SPECIFICATIONS

I Code - Stage Ill I FUJBlM7JA I
Engine Data - 1.25L
- - I
I Firing order I 1 -3-4-2 I
Description
Code
- Stage IV
1 Bore I 71.9 mm I
FUJAIM7JB
1 Stroke I 76.5 mm I
1 Displacement I 1242 cc I
I Compression ratio I 1O:I I
I Torque at 3500 rpm I 110 Nm I
Power output at 5700 rpm (Engine codes M7JAIM7JB)
Power output at 5700 rpm (Engine codes FUJAIFUJB)
I Maximum permissible engine speed continuous I 5950 rpm I
51 kW (70 PS)
55
kW (75 PS)
meperissible engine speed intermittent I 6175 rpm I
I Idle speed I 750 rprn I
I Maximum oil consumption I 0.5Ll1 OOOkm I
Engine Data - 1.4L
I Description
Code
FXJAIFXJ B
I Firing order I 1-3-4-2 I
Bore
Stroke
I Power output at 5700 rpm I 59 kW (80 PS) I
76.0 mm
76.5 mm
Displacement
Compression ratio
I Torque at 3500 rpm I 124 Nm I
1388 cc
11:l
I Maximum permissible engine speed continuous I 6450 rpm I
I Maximum oil consumption I 0.5Ll1 OOOkm I
Maximum permissible engine speed intermittent
ldle speed
Engine Data
- I .6L Description 6800 rpm
750 rprn
I Engine code I FYJAIFYJB I
I Firing order I 1 -3-4-2. I
1 Bore I 79.0 mm I
1 Stroke I 81.4 mm I
2006.0 Fiesta 1212006 GI 54208en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V (Sigma)
SPECIFICATIONS
I Power output at 6000 rpm I 74 kW (1 00 PS) I
Description
Displacement
Compression ratio 1595
cc
11:l
Torque at 4000 rpm
Maximum permissible engine speed continuous
I Idle speed I 750 rpm I
1
146 Nm
6450 rpm
I Maximum permissible engine speed intermittent
I Maximum oil consumption I 0.5U1 OOOkm I
6800 rpm
Oil
Dressure
I Description I bar I
I Oil pressure (minimum, oil temperature 80°C) at 800 rpm I 1 .O I
I Oil pressure (minimum, oil temperature 80°C) at 2000 rpm I 2.5 I
I Pressure relief valve opening pressure I 4 1
Engine Oil Capacity - 1.25U1.4L
I Service fill including oil filter (EFLI 0) I 3.80 I
Description
Initial fill including oil filter
Service fill including oil filter
(EFL500)
I Service fill excluding oil filter I 3.50 I
Liters
4.25
3.75
I Initial fill including oil filter (EFLGOO) I 4.50 I
Engine Oil Capacity - 1.6L
I Initial fill including oil filter (EFLI 0) I 4.30 I
Description
I Service fill including oil filter (EFLGOO) I 4.25 I
Liters
I Service fill including oil filter (EFLI 0) I 4.10 I
I Service fill excluding oil filter I 3.75 I
Valve Clearance - 1.25U1.4L
Valve Clearance - 1.6L
Description
Valve clearance (engine cold), intake
Valve clearance (engine cold), exhaust
Description mm
I!{
mm
0.17 - 0.23
0.27
- 0.33
I Valve clearance (engine cold), intake I 0.17 - 0.23 I
I Valve clearance (engine cold), exhaust I 0.31- 0.37 I
2006.0 Fiesta 1212006 GI 54208en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)llI4L
Duratec-1 6V (Sigma)ll .6L Duratec-I 6V (Sigma)
SPECIFICATIONS
1 Description I Nm I Ib-ft I Ib-in I
I Camshaft pulley retaining bolt I 60 I 44 I - I
Timing belt tensioner two bolts fixing
Timing belt tensioner central bolt fixing
Crankshaft position (CKP) sensor bracket to
cylinder block retaining bolts
I Crankshaft rear oil seal carrier retaining bolts I 9 1 - I 80 I
20
25
I Cylinder block blanking plug I 20 I 15 1 - I
I Crankshaft pulley retaining bolt I a) I - I - I
15
18
I Engine coolant temperature (ECT) sensor I 18 I 13 I - I
-
-
I Exhaust manifold studs I 10 I - I 89 I
Positive crankcase ventilation (PCV) cover retaining
1 bolts Fuel
rail to intake manifold
Knock sensor (KS) retaining bolt
I Thermostat housing retaining bolts I 9 I - 1 80 I
I Flywheel to crankshaft retaining bolts I a) I - I - I
15
20
I Selector lever cable bracket to transaxle I 20 I 15 I I
11
15
Transaxle retaining bolts
Torque converter retaining nuts
I Intermediate shaft center bearing cap retaining nuts 1 25 I 18 I - I
-
-
I Ground cable to cylinder head retaining bolt I 18 I 13 I - I
47
27
Suspension strut and spring assembly top mount
retaining nuts
I a) Refer to procedure in this section.
35
20
2006.0 Fiesta 1212006 GI 54208en
-
procarmanuals.com

303-01 A-I 0
Engine - I .25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
DESCRIPTION AND OPERATION
Engine Engine emission control
Cross-mounted 16-valve DOHC engines with 59 European emissions level IV
kW (80 PS) and 74 kW (1 00 PS) respectively.
European on-board diagnosis (EOBD) for the
Valve train with mechanical bucket tappets monitoring of emissions-relevant components.
Cylinder block and cylinder head made of an
aluminium alloy
Diagnosis
Auxiliary drive via a self-tensioning belt without a
belt tensioner WDS diagnosis CD
817.
Instrument cluster (engine indicator lamp)
Engine management
Sequential multi-port fuel injection (SFI)
temperature and manifold absolute pressure (T-MAP) sensor in conjunction with a Siemens
powertrain control module (PCM).
Knock control
PCM with 84 pins and integrated passive anti-theft
system (PATS) immobiliser. Torquelpower
The Duratec 16V engines are characterised by
their high level of running refinement, low emission
levels and balanced development of power.
Description Description
Power curve for the 1.6L-Duratec 16V 3 Torque curve for the 1.6L-Duratec 16V ( ',I
Power curve for the 1.4L-Duratec 16V 4
Torque
curve for the 1.4L-Duratec 16V
2006.0 Fiesta 1212006 GI 7901 7en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
REMOVAL
Discard the nut.
64. Remove the engine front mount.
Discard the nuts.
65. Raise the vehicle and remove the engine
and transaxle assembly.
67. Remove the starter motor.
68. Remove the torque converter retaining
nuts.
Rotate the torque converter to gain access
to the remaining nuts.
Discard the nuts.
66. Using the special tool, attach the engine
and transaxle assembly to the engine hoist. 69.
Remove the transaxle right-hand retaining
bolts.
2006.0 Fiesta 1212006 G380458en
procarmanuals.com