oil FORD MUSTANG 1969 Volume One Chassis

04-05-04
Specifications

04-05-04

ATTACHING TORQUE SPECIFICATIONS -(By Axle Ring Gear Diameter)

Description

Differential Bearing Cap Bolt- 7 1/4"

8"

All Others

Differential Bearing Adjusting

Nut Lock Bolts

Carrier
to
Housing Stud Nuts-

8", 8 3/4", 9" 8 3/8"

Pinion Retainer
to
Carrier Bolts-

8", 8 3/4", 9" 9 3/8"

Ring Gear Attaching Bolts-

7 1/4"

All Others

Differential Pinion Shaft

Lock Pin
•
8 1/2" Only
Torque Lbs.
Ft.

40-55

55-70

70-85

12-25

25-40

30-45

40-55

65-80

15-22
Description

Rear Cover Screw and Washer

Assemblies
-8
1/4" &
8
1/2

Only

Oil Filler Plug

Rear Axle Shaft Bearing Retainer

Bolt Nuts:

Falcon,
Fairlane, Montego,

Mustang and Cougar (All)

Ford & Meteor (Exc.
8 1/2" R.G.)

Mercury,
T
Bird

Lincoln Continental (All)

Brake Backing Plate Bolt Nuts-

Ford & Meteor
8
1/2" Only
Torque Lbs.
Ft.

25-35

25-50

20-40

50-75

30-55

20-40

LUBRICANT
CAPACITIES
AND CHECKING PROCEDURES®

Vehicle

Falcon,
Mustang

Cougar, Fairlane, Falcon

Montego, Mustang

Ford,
Meteor

Ford,
Meteor

Cougar, Fairlane, Falcon, Ford,

Mercury, Meteor, Montego, Mustang

Lincoln,
Thunderbird
Engine

(C.I.D.)

170,
200

250,
302

240,
302

240,
302

351,
390,

428,
429

429,
460
Axle

Ratio

All

All

2.80:1,
3.10:1

All Except

2.80:1,
3.10:1

All

All
U.S. Measure

Capacity® (Pints)

2.5

4.0

4.0

5.0

5.0

5.0©
Imperial

Capacity
CD
(Pints)

2

31/5

3 1/5

4.0

4.0

4.0©

©All limited slip and Traction-Lok axles use ESW-M2C-104-A lubricant (C6AZ-19580-C).

All conventional axles use ESW-M2C-105-A lubricant (C6AZ-19580-B).

©Approximate refill capacity-Actual lubricant capacities are determined
by
filling
to
bottom
of
filler hole.

©To check these axles, the plug should be backed
out
slowly.
If
seepage occurs around the threads, the plug should
be
turned back
in

immediately to avoid any drainage. This indicates that the specified amount
of
lubricant
is
present
in
the axle.

SPECIAL TOOLS

FORD,
MERCURY, METEOR

Ford Tool No.

T66L-4204-L

T57L-500-A

T50T-100-A

TOOL-4235-C

T00L-4621-A

TOOL-1225-D

T00L42344

TOOL-1177

TOOL-U75-AB

T57L4220-A

T00L4221-AE

T00L-4221-AF

T66P-4220-P

TOOL-4851-K
Former No.

42211 or

42211-A

6005-M

6005-MS

B-160

4235C

—

—

4234-A

4245-B

1175-AB

—

4221-AF

T57L-4851-A

4851-K
Description

Limited-Slip Differential Check

Bench Fixture

Impact Hammer

Axle Shaft Remover

Drive Pinion Bearing and

Rear Wheel Bear Replacer

Rear Wheel Bearing Remover

Rear Wheel Bearing Installer

Rear Wheel Bearing Oil Seal Installer

Rear Wheel Bearing Oil Seal Remover

Differential Bearing Remover

Differential Bearing Remover

U-Joint
Flange Holder
Ford Tool No.

T53T4851-A

T00L4858-D

T57L4614-A

T00L4621-K

T53L-200-A

T57L-4625-A or

T00L4625-K

T57L4616-A or

T00L4615-D

T58L-101-A

T55P4616-A2

T57L4621-B or

T00L4621-L

T58L4676-A

T00L4858-E
Former No.

4851-A, D

—

4614

4621-K

—

4625-K

—

—

—

—

4676-F

4858-E
Description

U-Joint
Flange Remover

U-Joint
Flange Remover

Drive Pinion Retainer Support

Pinion Rear Bearing Cone Remover

Handle Adapter

Pinion Pilot Bearing Remover and

Installer

Pinion Front Bearing Cup Remover

and Replacer

Puller Attachment—For Bearing

Cup Removal

Pinion Rear Bearing Cup Remover

and Replacer

Pinion Rear Bearing Cone Installer

Drive Pinion Oil Seal Replacer

U-Joint
Flange and Pinion Bearing

Replacerprocarmanuals.com

04-05-05
Specifications

04-05-05

SPECIAL TOOLS

FORD MERCURY, METEOR (Continued)

Ford Tool No.

T57L-4221-A1 or

Tool-4222-K

TOOL 6565-AB

TOOL 6565

TOOLS 4201-C

andD

TOOL-T57L-

4067-A

TOOL-T50T-100-A

T00L-T66L-

12132-B

CJ-6625 (Snap-

On)
Foniisr
NO.

4222-H

6565-AB

6565

4201-C

4067-B

—

—

—
Description

Differential Bearing Installer

Adapter

Dial Indicator

Differential Backlash and Runout

Gauge with Universal Bracket, Dial

Indicator and Bracket

Differential Bearing Adjuster Wrench

Impact Hammer-Long

Adapter

Puller
Ford Tool No.

TOOL-T60K-

7697-B

T00L-T65F-

1177-A

T00L-T65L-

4851-A

TOOL-OTC-951

T00L-T67P-

4616-A

TOOL-T53T-

4621-C
Fomor No.

—

—

—

—

—
Description

Transmission Extension Housing

Bushing Repiacer

Rear Wheel Bearing Oil Seal Repiacer

Flange (Universal Joint) Axle End

Remover

Universal Puller

Pinion Bearing Cups Repiacer

Pinion Bearing Cone Repiacer

COUGAR, FAIRLANE, FALCON,

Ford Tool No.

T50T-100-A

T58L-101-A

T62L-201-A

T56L-400-A

T57L-500-A

T00L-1175-AB

T50T-100-Aand

TOOL-1175-AB

T60K-1177-B

T60K-1225-Aor

T00L-1225-C

TOOL-1225-B

T00L-T54-P-

3044-A

T00L-T57L-

4067-A

T57L-4067-Aor

T60K-4067-A

TOOL-4201-C

andD

T65K-4204A or

T59L-4204-A

T00L-4221-AL

T57L-4221-A

T00L-4222-H

T66L-4235-A
Former No.

B-160

-

4851-A

-

1175-AB

1175-AE

1177-B

4067-B

4221 or

4211-A

4201-C

4067-E

4221-AL

4222-K

4222
MONTEGO, MUSTANG

Description

Impact Hammer

Puller Attachment

Handle Adapter

Puller

Bench Mounted Holding Fixture

Grease Seal Remover (Head Only)

Seal Remover

Rear Wheel Bearing Oil Seal

Axle Shaft Bearing Remover and Repiacer

Axle Shaft Searing Remover

Axle Shaft Bearing Repiacer

Front Suspension Upper and Lower Arm

Overhaul Tool Kit

Differential Bearing Adjuster Nut

Wrench

Limited-Slip Differential Check

Differential Backlash and Runout Gauge

With Universal Bracket, Dial Indicator

and Bracket

Differential Bearing Adjuster Nut

Wrench

Differential Bearing Cone Remover

Pilot (Use with T00L-4221C or

T00L-4851-A)

Differential Bearing Cone Repiacer

Differential Bearing Cone Repiacer

Rear Axle Shaft Assembly Remover

Adapter
Ford Tool No.

T57L-4614-A

T00L-4615-J

T60K-4616-A

T57L-4616-A

T57L-4616-A2

T55P-4616-A2

T00L-4621-K

T62F-4621A

T62F-4625-A

T55P-4676-A

T62F4676A

T53T-4851A

T57L-4851-A

T00L-4858-E

T65K-4204-A

T59L-4204-A

T00L-6565-AB

TOOL-6565
Former No.

4614

4615-J

4615-HF

4625-HR

4615-
E

andP

4615-
E

andF

-

4621-K

4625-AC

land 2

4676-G

4676-
H

4851-A

4858-D

4851-K

4858-
E

—

44211 and

44211-A

6565-AB

6565
Description

Drive Pinion and Drive Pinion Retainer

Assembly Support

Drive Pinion Front Bearing Cup Remover

Pinion Bearing Cup Repiacer

Pinion Front Bearing Cup Remover

Pinion Front Bearing Cup Repiacer

Pinion Rear Bearing Cup Repiacer

Drive Pinion Rear Bearing Cone Remover

Pinion Bearing Cone Repiacer

Drive Pinion Pilot Bearing Remover

and Repiacer

Drive Pinion Oil Seal Repiacer

Drive Pinion Oil Seal Repiacer

Flange (Universal Joint) Axle End

Remover

Universal Joint Flange Holder

Companion Flange and Pinion Bearing

Repiacer

Limited-Slip Differential Torque Check

Adapter

Locking Differential Torque Check

Adapter

Dial Indicator

T68P-4946-A - Traction-Lok Shim Template Toolprocarmanuals.com

04-05-06

Specifications

04-05-06

THUNDERBIRD, CONTINENTAL MARK
III

Ford Tool No.

T50T-100-A

T50T-100-A&

TOOL-1175-AB

T00L-1225-DA

TOOL-4005

TOOL-4020-B

T57L-4067-A

TOOL-4201

TOOL-4201-C

TOOL-4205-B

TOOL-4205-C

T00L-4221-C

T00L-4222-H

T00L-4235-C

T00L-4245-B
Former No.

T50T-100-C

1175-AE

1225-DA

4005

4020-B

_

4201

4201-C

4205-B

4205-C

4221-C

4222-H

4235-C

4245-B
Description

Slide Hammer

Seal Remover

Rear Wheel Bearing Remover

Engine Repair Stand Axle Adapter-

Keyed Shaft

Pinion Depth Gauge-Complete With

Depth Micrometer and Gauge Block

Differential Bearing Adjuster Wrench

Pinion Shaft Drive
Nut

Differential Backlash
&
Runout

Gauge With Univ. Bracket, Dial

Indicator and Bracket

Differential Assembly Bench Holder

Axle Housing Dummy Bearings (1
pr.)

Differential Side Bearing Remover

Differential Bearing Cone Replacer

Axle Shaft
&
Bearing Remover

Wheel Bearing Seal Replacer
Ford Tool No.
Former No. Description

TOOL-4616
4616
Drive Pinion Bearing Cup Replacer

(Front)

T00L-4621-A 4621-A Drive Pinion Bearing and Rear Wheel

Bearing Replacer

T00L-4621-BA 4621-BA Rear Pinion Bearing Remover

TOOL-4628 4628 Pinion Rear Bearing Cup Replacer

T00L-4628-B 4628-B Pinion Bearing Front Cup Remover

T00L-4628-D 4628-D Pinion Rear Bearing Cup Remover

T64N-4676-A 4676 Pinion Shaft Oil Seal Replacer

T68P-4851-A
-
Universal Joint Flange Holder

T64N-4858-A 4858-B Companion Flange
&
Pinion Bearing

Replacer

T00L-4858-G 4858-G Pinion Flange Nut Adjusting Wrench

(Use With T64N-4858-A)

TOOL-4859 4859 Companion Flange Dust
Shield
Replacer

T00L-6565-AB
-
Dial Indicator Adapter

TOOL-6565
-
Dial Indicator

T00L-7657-J 7657-J Extension Housing Bushing
&

Seal Replacer

LINCOLN CONTINENTAL

Ford Tool
No.

T00L-4245-B

TOOL-4616

T00L-4621-A

T00L-4621-BA

TOOL-4628

T00L-4628-B

T64N-4628-B

T00L-4628-D

T64N-4676-A

T00L-4851-K

T64N-4858-A

T00L-4858-G

TOOL-4859

T00L-6565-AB

TOOL 6565

T00L-7657-J
Former
No.

4245-B

4616

4621-A

4621-BA

4628

4628-B

4628-D

4676

T57L-4851-A

4858-B

4858-G

4859

7657-J
Description

Wheel Bearing Seal Replacer

Drive Pinion bearing
Cup

Replacer (Front)

Drive Pinion Bearing
and
Rear

Wheel Bearing Replacer

Rear Pinion Bearing Remover

Pinion Rear Bearing
Cup
Replacer

Pinion Bearing Front
Cup
Remover

Pinion Rear Bearing Cup Remover

Pinion Shaft
Oil
Seal Replacer

Universal Joint Flange Holder

Companion Flange
&
Pinion Bearing

Replacer

Pinion Flange
Nut
Adjusting Wrench

(Use With T64N-4858-A)

Companion Flange Dust Shield

Replacer

Dial Indicator Adapter

Dial Indicator

Extension Housing Bushing
&

Seal Replacer
Ford Tool
No.
Former
No.

T50T-100-A

T50T-100-A&

TOOL-1175-AB

TOOL-1225-DA

TOOL-4000-C

TOOL-4005

TOOL-4020-B

TOOL-4201

TOOL-4201-C

TOOL-4204-A

TOOL-4205-B

TOOL-4205-C

T00L-4209-C

T00L-4221-C

T00L-4222-H

T00L-4235-C
Description

T50T-100-C Slide Hammer

1175-AE

1225-DA

4000-C

4005

4020-B

4201

4201-C

4205-B

4205-C

4209-C

4221-C

4222-H

4235-C
Seal Remover

Rear Wheel Bearing Remover

Differential Housing Spreader

Engine Repair Stand Axle Adapter-

Keyed Shaft

Pinion Depth Gauge-Complete With

Depth Micrometer
and
Gauge

Block

Pinion Shaft Drive
Nut

Differential Backlash
&
Runout

Gauge With Univ. Bracket, Dial

Indicator
and
Bracket

Limited Slip Differential Check

Differential Assembly Bench Holder

Axle Housing Dummy Bearings

(1
pi")

Pinion Tension Scale With

4209-C12 Socket

Differential Side Bearing Remover

Differential Bearing Cone Replacer

Axle Shaft
&
Bearing Removerprocarmanuals.com

05-02-04
General Clutch Service

05-02-04

CLEANING AND INSPECTION

RELEASE BEARING

Wipe all oil and dirt off the release

bearing. The bearing is prelubricated

and should not be cleaned with sol-

vent.

Inspect the bearing retainer for

loose spring clips and rivets.

Inspect the release bearing assembly

for burrs which may cause the assem-

bly to drag on the transmission bear-

ing retainer. Any such burrs should be

cleaned up with fine crocus cloth. If

burrs are found, inspect the transmis-

sion input shaft bearing retainer for

evidence of scoring. Any scoring

should be polished out with crocus

cloth. Coat the bearing retainer with a

thin film of lithium-base grease

(C3VY-19586-A). Prior to release

bearing installation, apply a light film

of lithium base grease (C3VY-

19586-A) on both sides of the release

lever fork where it contacts the release

bearing hub and retaining springs.

Apply a light film of lithium base

grease (C3VY-19586-A) plate to the

release bearing surface that contacts

the pressure plate fingers. Carefully

fill the grease groove inside the bear-

ing hub with lithium base grease (no

polyethylene). Clean all excess grease

from the bore of the bearing hub. Ex-

cess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, care must be

exercised when applying lubricants to

the release bearing, release bearing

hub and the release lever fork to avoid

excessive grease from contaminating

the clutch disc.

Hold the bearing inner race and ro-

tate the outer race while applying

pressure to it. If the bearing rotation

is rough or noisy, replace the bearing.

Most release bearing failures are

caused by improper clutch pedal ad-

justments. If the clutch linkage does

not have enough free travel, the re-

lease bearing will constantly touch the

release fingers and will spin whenever

the engine is running.

When installing a release bearing on

vehicles equipped with separate hub

and bearing, use the tool shown in

Fig. 5.

Release bearing failure can be

caused by the release lever contact

points being out of plane. Check the

wear on the release bearing assembly

where the release lever contacts it.

If one side of the assembly shows

more wear than the other, the release
lever is bent out of plane, or is not

centering on the bracket on the fly-

wheel housing.

Misalignment between the engine

and transmission can cause release

bearing failure. Other symptoms of

misalignment are transmission jump-

ing out of gear, especially third gear,

drive line vibration; excessive wear in

the pilot bushing, excessive clutch disc

spin time resulting in gear clash, and

excessive transmission gear wear.

PRESSURE PLATE AND COVER

Inspect the surface of the pressure

plate for burn marks, scores, or rid-

ges.
Generally, pressure plate resur-

facing is not recommended. However

minor burn marks, scores, or ridges

may be removed. During the resurfac-

ing process, the flatness of the pres-

sure plate must be maintained. If the

pressure plate is badly heat-checked or

deeply scored, replace the pressure

plate and cover assembly. Clean pres-

sure plate and flywheel surfaces with a

suitable solvent, such as alcohol to be

sure the surfaces are free from any oil

film. Do not use cleaners with petrole-

um base, and do not immerse the

pressure plate in the solvent.

Place the plate on the floor, being

careful not to score or scratch the sur-

face.
Force each individual finger

down, then release quickly. If the fin-

ger does not return quickly, a binding

condition is indicated, and the pres-

sure plate should be replaced.

The pressure plate should be lubri-

cated with a lithium-base grease be-

tween the driving lugs and the edges

of the pressure plate openings, as

shown in Fig. 6. Depress the pressure

plate fingers fully, apply the lubricant,

and then move the fingers up and

down until the lubricant is worked in.

Do not apply excessive lubricant.

CLUTCH DISC

Inspect the clutch disc facings for

oil or grease. Eliminate the source of

any oil or grease before replacing the

disc. An excessive amount of grease in

the pilot bushing or release bearing

hub will find its way to the disc fac-

ings.
Too much lubricant in the trans-

mission or a plugged transmission

vent will force the transmission lubri-

cant out the input shaft and onto the

disc facings. Also, rear main bearing

oil seal leaks or oil leaks from the fly-

wheel mounting bolts can contaminate

the clutch disc.
Inspect the clutch disc for worn or

loose facings. Check the disc for worn

or loose facings. Check the disc for

distortion and for loose rivets at the

hub.
Check for broken springs.

Springs loose enough to rattle will not

cause noise when the car is operating.

Replace the disc assembly if any of

these defects are present. Be especially

careful when installing a new disc to

avoid dropping it or contaminating it

with oil or grease.

PILOT BUSHING

Check the fit of the clutch pilot

bushing in the bore of the crankshaft.

The bushing is pressed into the

crankshaft and should not be loose.

Inspect the inner surface of the bush-

ing for wear or a bell-mouthed condi-

tion. If the bushing is worn or dam-

aged, replace the bushing with a new

service bearing. Refer to the applica-

ble engine for the replacement proce-

dure.

C 1785-A

FIG. 5—Installing Clutch Release

Bearing on Hub

PRESSURE PLATE

AND COVER

DRIVING

LUG
FLYWHEEL

C2048-A

FIG. 6—Pressure Plate Lubrication

Pointsprocarmanuals.com

05-03-04
Clutch

05-03-04

bushings, position the clutch pedal and

bushings in the pedal support.

8. Install the retaining ring on the

clutch pedal shaft.

9. Position the assist spring in the

pedal support bracket and the assist

spring bracket. Rotate the assist

spring bracket clockwise until the

upper bolt holes line up and install the

bolt. Torque both the upper and lower

bolts to specification.

10.
Check the clutch pedal free

travel and adjust as required.

MUSTANG, COUGAR

1.
Disconnect the battery ground

cable.

2.
Remove the steering column.

Refer to Group 3 of this manual for

the procedure.

3.
Remove the two capscrews re-

taining the master cylinder or booster

to the dash panel. Then remove the

two capscrews retaining the pedal sup-

port bracket to the dash panel.

4.
Working inside the vehicle, dis-

connect the clutch pedal-to-equalizer

rod at the clutch pedal by removing

the retainer and bushing.

5.
Secure the clutch pedal against

the bumper stop with a small C-clamp

as shown in Fig. 6.

6. Disconnect the stop light switch

wires at the connector.

7.
Remove the switch retainer and

slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Then lower the switch away from the

pin.
Remove the master cylinder push

CLUTCH PEDAL ASSIST SPRING
rod, bushing and nylon washer from

the brake pedal pin.

8. Remove the screw retaining the

pedal support bracket to the top inner

cowl bracket (Fig. 6).

9. Remove the two sheet metal

screws retaining the pedal support

bracket to the dash panel.

10.
Remove the two screws retain-

ing the pedal support bracket to the

upper cowl brace and lower the pedal

support bracket away from the steer-

ing column studs.

11.
Remove the pedal support

bracket assembly from the vehicle.

12.
Mount the bracket in a vise.

13.
Remove the small C-clamp se-

curing the clutch pedal to the bumper.

Slowly pivot the pedal away from the

bumper until the assist spring can be

lifted from its seat.

14.
Remove the retainer clip from

the clutch and brake pedal shaft.

Then, remove the clutch pedal and

shaft assembly, brake pedal assembly,

and bushings from the pedal support

bracket.

15.
Apply a coating of SAE 10 en-

gine oil to the bushings and locate all

bushings in their proper places on the

brake and clutch pedal assemblies.

16.
Position the brake pedal to the

pedal support bracket. Install the

clutch and brake pedal shaft through

the pedal support and brake pedal as-

sembly. Install the retainer.

17.
Install the clutch pedal assist

spring and pivot the pedal against its

bumper stop. Secure the pedal against

the bumper with a small C-clamp as

TOP INNER COWL-TO-BRACKET

RETAINING SCREW

C2057-A

FIG.
6—Clutch
Pedal —Mustang and Couga?
shown in Fig. 6.

18.
Position the pedal support

bracket assembly to the dash panel

and to the steering column retainer

studs.

19.
Align the pedal support bracket

holes with the holes in the dash panel

and install the two sheet metal screws.

20.
Install the two capscrews at-

taching the pedal support bracket to

the upper cowl bracket.

21.
Install the screw attaching the

support bracket to the top inner cowl

bracket (Fig. 6).

22.
Install the inner nylon washer,

bushing master cylinder push rod on

the brake pedal pin. Position the stop

light switch so that it straddles the

push rod with the switch slot on the

pedal pin and the switch outer hole

just clearing the pin. Slide the switch

completely onto the pin, and install

the outer nylon washer. Secure with

the self-locking pin.

23.
Connect the stop light switch

wires to the connector and install the

wires to the retaining clip.

24.
Connect the clutch pedal-

to-equalizer rod to the clutch pedal

assembly with the bushing and retain-

er and remove the C-clamp from the

bracket.

25.
Working from the engine side

of the dash panel, install the two cap-

screws attaching the pedal support

bracket to the dash panel. Then install

the two screws attaching the master

cylinder to the dash panel.

26.
Install the steering column.

Refer to Group 3 of this manual for

the procedure.

27.
Adjust the clutch pedal free

travel.

28.
Check the brake pedal free

height and travel measurements

(Group 2).

29.
Connect the battery ground

cable.

CLUTCH PEDAL AND/OR

BUSHING REMOVAL

AND INSTALLATION

MOM EGO, FALCON

FAIRLANF

1.
Remove the retaining clip (Fig.

2) that secures the equalizer rod to the

clutch pedal. Disconnect the rod from

the pedal.

2.
Remove the lower bolt retaining

the assist spring bracket to the pedal

support. Then, loosen the upper

bracket retaining bolt (approximately

4 turns) and disconnect the spring

from the clutch pedal and bracket.

3.
Disconnect the brake pedal push

rod from the brake pedal.procarmanuals.com

05-03-05
Clutch

05-03-05

4.
Remove the bolt that secures the

left air vent control cable bracket to

the instrument panel. Position the

control cable to one side.

5.
Remove the retaining clip and

flat washer from the clutch pedal

shaft. Then, remove the shaft, bush-

ing, clutch pedal and brake pedal

from the support.

6. Remove the bushings from the

pedal shaft, and transfer the pedal

pad.

7.
Lubricate the clutch pedal shaft

bushings and position them on the

shaft. Then, position the brake pedal

and clutch pedal in the pedal support.

8. Install the flat washer and re-

taining clip on the pedal shaft.

9. Position the assist spring to the

pedal and bracket. Pry the bracket

forward and install the lower bolt.

Torque the bolts to specifications.

10.
Position the master cylinder

push rod, bushing, and washers on the

brake pedal and secure with a retain-

ing clip.

11.
Connect the equalizer rod to

the clutch pedal and secure it in place

with a retaining clip.

12.
Position the air vent control

cable bracket to the instrument panel

and secure with the attaching bolt.

13.
Adjust the clutch pedal free

travel.

EQUALIZER BAR AND/OR

BUSHING REMOVAL AND

INSTALLATION

FORD, MERCURY

AND METEOR

1.
Raise the vehicle and disconnect

the clutch pedal-to-equalizer rod at

the equalizer bar (Fig. 1).

2.
Disconnect the return spring and

retaining spring at the release lever.

Separate the release lever rod from

the release lever.

3.
Remove the equalizer bar frame

bracket from the frame.

4.
Remove the equalizer bar from

the pivot on the flywheel housing.

5.
Remove the wire clip to replace

the outer bushing and the snap ring
from the inner pivot stud to replace

the inner bushing.

6. Position the flat washer, felt

washer and bushing on the inner and

outer pivots. Secure these parts with

the snap ring.

7.
Position the equalizer bar on the

inner pivot and bolt the equalizer bar

frame bracket to the frame. Torque

the attaching bolts to specification.

8. Install the clutch release rod, re-

turn spring and retaining spring.

9. Connect the clutch pedal rod to

the equalizer bar.

10.
Adjust the clutch pedal free

travel.

MUSTANG, COUGAR,

MONTEGO, FALCON,

FAIRLANE (EXCEPT

MONTEGO AND FAIRLANE

WITH 390 V-8)

1.
Disconnect the clutch pedal

equalizer rod at the equalizer bar

(Figs.
2 and 3).

2.
Raise the vehicle and disconnect

the release lever, return spring at the

lever.

3.
Remove the equalizer bar outer

bracket and bushing assembly.

4.
Remove the release rod from the

equalizer bar, and then remove the

equalizer bar. Remove the bushing

and washers from the inner mounting

stud.

5.
Position the equalizer bar, wash-

ers,
inner bushing, and retainer on the

inner stud.

6. After positioning the outer bush-

ing, install the outer bracket (with the

equalizer bar in place).

7.
Connect the release rod and the

release lever return spring.

8. Lower the vehicle. Connect the

clutch pedal equalizer rod to the

equalizer baY and secure with the re-

taining pin.

9. Adjust the clutch pedal free trav-

el as required.

MONTEGO AND

FAIRLANE—390 V-8

1.
Disconnect the clutch pedal
equalizer rod at the equalizer bar (Fig.

2).

2.
Raise the vehicle and disconnect

the return spring at the release lever.

Disconnect the release lever rod from

the equalizer lever.

3.
Remove the equalizer bar center

bolt.

4.
Separate the equalizer bar and

remove both sections from the vehicle.

5.
Remove the bolts retaining the

equalizer bar inner bracket to the fly-

wheel housing and remove the bracket

and bushing assembly.

6. Remove the equalizer bar outer

bracket and bushing assembly.

7.
Remove the snap ring, bushing,

and felt washer from each bracket as-

sembly.

8. Position a felt washer, and bush-

ing on each bracket assembly and se-

cure with the snap ring.

9. Install the outer bracket and

bushing assembly to the frame (Fig.

2).
Torque the bracket attaching bolts

to specifications.

10.
Position the outer section of the

equalizer bar on the outer bracket

pivot.

11.
Connect the two sections of the

equalizer bar. Insert the inner bracket

pivot into the equalizer bar and install

the assembly to the flywheel housing.

Torque the attaching bolts to specifi-

cations.

12.
Install the equalizer bar center

bolt and torque to specifications.

Make sure that both ends of the

equalizer bar are against the felt

washers.

13.
Connect the release rod and the

release lever return spring.

14.
Adjust the clutch pedal free

travel.

15.
Lower the vehicle. Connect the

clutch pedal equalizer rod to the

equalizer bar and secure with the re-

taining clip.

16.
Check the free travel at the

pedal for conformance to specifica-

tions.
Readjust if necessary.

REMOVAL AND INSTALLATION

CLUTCH REMOVAL

1.
Raise the vehicle on a hoist.

2.
Disconnect the drive shaft from

the rear U-joint flange. Then, slide the

drive shaft off the transmission output

shaft. Insert the appropriate tool over

the output shaft and into the extension

housing oil seal.
3.
Disconnect the speedometer

cable from the extension housing.

4.
Disconnect the gear shift rods

from the transmission. If the vehicle is

equipped with a four-speed transmis-

sion, remove the bolts that secure the

four-speed transmission, disconnect

the front brake cable from the cross-

member and remove the crossmem-
member from the vehicle.

5.
Remove the bolts that attach the

transmission to the flywheel housing.

6. Move the transmission rearward

until the input shaft clears the fly-

wheel housing, then remove it from

the vehicle.

7.
Disconnect the clutch release

lever retaining spring from the release

lever.procarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com

05-04-02

Specifications

05-04-02

TORQUE LIMITS (FT-LBS)

Description

Lower Access Clutch Cover Pan to Flywheel Housing Bolts (Cast Iron Housing)

Transmission Assembly to Flywheel Housing Bolts

Pressure Plate and Cover Assembly to Flywheel Attaching Bolts

Clutch Release Equalizer Frame Bracket Bolts

Clutch Pedal Free Travel Adjustment Nut

Flywheel Housing to Cylinder Block Bolts
6-Cylinder

8-Cylinder

Clutch Pedal Assist Spring Bracket to Brake Pedal Support Bracket
Meteor

Ford,
Mercury

17-20

37-42

12-20

15-24

15-20

_

12-17
Mustang,
Cougar

Fairlane, Montego, Falcon

-

-

12-20

15-24

15-20

23-33

40-50

12-17

SPECIAL TOOLS

Tool No.

A-37H

T61L-7657-Aor B

T57L-7657-A

T64P-7657-A
Description

Clutch Disc Aligner-Universal

Transmission Extension Housing Oil Seal

Replacer
Tool No.

CJ91B

T64L-6392-A

T49P-7580-A
Description

Universal Joint Bearing Replacer

Dia-L-lgner Gauge

Clutch Release Bearing Replacerprocarmanuals.com

06-01-02
General Transmission Service

06-01-02

REAR SEAL REPLACEMENT

1.
Remove the drive shaft.

2.
Remove the seal from the exten-

sion housing with the tool shown in

Fig. 2.

3.
Install the new seal in the exten-

sion housing with the tool shown in

Fig. 3.

4.
Install the drive shaft.

.REAR OIL SEAL

Tool-T61L-7657-A

EXTENSION HOUSING

C 1830.A

FIG. 3—Installing Extension

Housing Seal
Too/-7J75-AB

Tool-TSOT-lOO-A

FIG. 2—Removing Extension Housing Seal

EXTENSION HOUSING

Tool-T52L-7000-GAE

or 7000-G

C1O28-D

FIG. 4—Removing Extension

Housing Bushing and Seal
EXTENSION HOUSING
D
1927. A

Tool—T57P-7697-B

57-G

BUSHING

C 1832.A

FIG. 5—Installing Extension

Housing Bushing

REAR BUSHING AND SEAL

REMOVAL AND INSTALLATION

1.
Remove the drive shaft from the

vehicle.

2.
Insert the tool shown in Fig. 4

into the extension housing until it

grips on ihe front side of the bushing.
3.
Turn the screw clockwise until

the seal and the bushing are free of

the housing.

4.
Drive a new bushing into the ex-

tension housing with the tool shown in

Fig. 5.

5.
Install a new seal in the housing

as shown in Fig. 3.

6. Install the drive shaft.
LUBRICATION

Lubricant level should be even with

the bottom of the filler hole at the

right side of the transmission case.

CLEANING AND INSPECTION

CLEANING

1.
Wash all parts, except the ball

bearings and seals in a suitable clean-

ing solvent. Brush or scrape all foreign

matter from the parts. Be careful not

to damage any parts with the scraper.

Do not clean, wash or soak transmis-

sion seals in cleaning solvents. Dry all

parts with compressed air.

2.
Rotate the ball bearings in a

cleaning solvent until all lubricant is

removed. Hold the bearing assembly

to prevent it from rotating and dry it

with compressed air.

3.
Lubricate the bearings with ap-

proved transmission lubricant and

wrap them in a clean, lint-free cloth

or paper until ready for use.

4.
Clean the magnet welded to the

bottom of the case with kerosene or

mineral spirits.
INSPECTION

1.
Inspect the transmission case for

cracks, worn or damaged bearings

bores,
damaged threads or any other

damage that could affect the opera-

tion of the transmission.

2.
Inspect the front face of the case

for small nicks or burrs that could

cause misalignment of the transmis-

sion with the flywheel housing. Re-

move all small nicks or burrs with a

fine stone.

3.
Replace a cover that is bent or

distorted. Make sure that the vent

hole in the cover is open.

4.
Check the condition of the shift

levers, forks, shift rails and the lever

and shafts.

5.
Examine the ball bearing races

for cracks, wear or roughness. Inspect

the balls for looseness, wear, end play
or other damage. Check the bearings

for looseness in the bores. If any of

these conditions exist, replace the

bearings.

6. Replace roller bearings that are

broken, worn or rough.

7.
Replace the countershaft (clust-

er) gear if the teeth are chipped, brok-

en or worn. Replace the countershaft

if it is bent, scored or worn.

8. Replace the reverse idler gear or

sliding gear if the teeth are chipped,

worn or broken. Replace the idler

gear shaft if bent, worn or scored.

9. Replace the input shaft and gear

if the splines are damaged or if the

teeth are chipped, worn or broken. If

the roller bearing surface in the bore

of the gear is worn or rough, or if the

cone surface is damaged, replace the

gear and the gear rollers.

10.
Replace all other gears that areprocarmanuals.com

06-02-03
Ford Design Three Speed Transmission

06-02-03

STOP
PIN

GROMMET

Tool -
T67P.7347.A

GROMMET

LEVER

CONTROL ROD REMOVAL
^S.
GROMMET INSTALLATION

SET STOP PIN SO THAT THE GROMMET

Tool
-
T67P.734LA
AND
SHIFT ROD ARE PROPERLY SEATED
OMMET—^

SEATED
\

CONTROL ROD INSTALLATION

CONTROL ROD

STOP
PIN

FIG. 4—Removing
or
Installing Shift Linkage Grommet

GEAR SHIFT LINKAGE

ADJUSTMENT—FLOOR MOUNTED

1.
Loosen
the
three shift linkage

adjustment nuts. Install
a 1/4
inch
di-

ameter alignment pin through the con-

trol bracket and lever alignment holes

shown
in Fig. 18.

2.
Tighten
the
three linkage adjust-

ment nuts
and
then remove
the
align-

ment
pin.

3.
Check
the
gear shift lever
for a

smooth crossover.

COLUMN-MOUNTED

SHIFT LINKAGE

GROMMET REMOVAL
AND

INSTALLATION

The column-mounted shift lever
as-
sembly incorporates
an oil
impregnat-

ed plastic grommet
in the
end
of
each

lever
arm. A
special tool T67P-

7341-A
is
required
to
install the grom-

met
in the
shift lever,
and to
install

the shift linkage
rod
into
the
grom-

met. Remove
and
install
the
grommet

as follows:

1.
Place
the
lower
jaw of the
tool

between
the
shift lever
and the
shift

rod.
Position
the
stop
pin
against
the

end
of the
shift
rod
(Fig.
4)
and force

the
rod out of the
grommet. Remove

the grommet from
the
shift lever
by

cutting
off the
large shoulder with
a

sharp knife. The groin met must
be re-

moved from
the
shift lever
and a new

one installed each rime
'he rod is
dis-

connected.

2.
Before installing
a
new grommet,
C 2090-A

adjust
the
stop
pin as
necessary
to

properly install
the
grommet and coat

the outside
of
the grommet with lubri-

cant. Then, place
the
grommet
on the

stop
pin and
force
it
into
the
shift

lever hole. Turn
the
grommeit several

times
to be
sure
it is
properly seated.

3.
Readjust
the
stop
pin to a
length

which
is
sufficient
to
install
the
shift

rod into
the
grommet
(Fig.
4).
If
the

pin height
is not
adjusted,
the
shift

rod
may be
pushed
too far
through

the grommet causing damage
to the

grommet retaining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
shift
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of
the grom-

met.

REMOVAL AND INSTALLATION

REMOVAL

1.
Raise
the
vehicle
on a
hoist.

2.
Mark
the
drive shaft
so
that
it

may
be
installed
in the
same relative

position. Disconnect
the
drive shaft

from
the
rear U-joint flange.

3.
Slide
the
front
of the
drive shaft
out
of the
transmission extension

housing
and off the
output shaft
In-

sert
the
tool shown
in (Fig. 2),
Part

6-1 into the extension housing
to
pre-

vent
the
lubricant from leaking
out of

the transmission.

4.
Remove
the cap
screw
and
lock

washer that secures
the
speedometer
cable retainer
to the
extension hous-

ing. Pull
the
speedometer cable
out of

the extension housing.

5.
On
vehicles equipped with
a

column-mounted gear shift selector,

remove
the
shift rods from
the
shift

levers
at
the transmission. On vehicles

equipped with
a
floor-mounted gearprocarmanuals.com