power steering FORD MUSTANG 2003 Owners Manual

30.
NOTE: LH shown; RH similar.
Using a suitable container, drain coolant from the engine block. zInstall the drain plugs when finished.
31. Remove the four bolts and the power steering pump.
RH cylinder head 32. Remove the RH exhaust manifold. 1. Remove the RH exhaust manifold nuts.
2. Remove the RH exhaust manifold.
3. Remove the RH exhaust manifold gasket and discard. Klj . 10 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

17. Disconnect the A/C manifold suction tube.
18. Disconnect the A/C pressure cycle switch.
19. Remove the nut and separate the liquid tube from the A/C condenser.
20. Disconnect the power steering hose from the reservoir. Klj . 4 ba
122003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

34. Remove the starter. For additional information, refer to
Section 303 - 06 .
35. Remove the nine bell housing bolts.
36. Remove the bolt and the body ground.
37. Remove the power steering pump. For additional information, refer to Section 211 - 02 .
38. Lower the vehicle.
39. Remove the safety clip from the suction tube. Klj . 8 ba
122003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

21. Rotate the belt tensioner and remove the accessory drive belt.
22. Remove the power steering reservoir bracket as an assembly.
1. Disconnect the supply line from the pump.
2. Remove the three bolts and reservoir.
23. Remove the upper generator support bracket.
24. Remove the bolts and the generator. Klj . 8 ba
242003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

31.
NOTE: One side shown, other side similar.
Using a suitable container, drain coolant from the engine block. zInstall the drain plugs when finished.
32. Remove the four bolts and the power steering pump.
33. Remove the compressor. 1. Remove the bolts.
2. Remove the compressor. Klj . 11 ba
242003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

65.
NOTE: Only three bolts are required for installation.
Install the power steering pump. zPosition the power steering pump.
z Install the bolts.
66. Lubricate the O- ring seal with PAG compressor oil, YN-12C, F7AZ-19589- DA or equivalent
meeting Ford specification WSH- M1C231-B.
Install the A/C compressor.
67. Install the oil filter adapter. Klj . 25 ba
362003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

36. Install the RH engine mount.
37.
NOTE: Only three bolts are required for installation.
Install the power steering pump bolts. zPosition the power steering pump.
z Install the bolts.
38. Install the special tool between the valve spring coils to prevent valve stem seal damage. Klj . 14 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

52. Install the thermostat and O-
ring.
z Install a new O- ring as necessary.
53. Install the coolant outlet adapter.
54. Install the bolts and the generator.
55. Install the upper generator support bracket.
56. Position the power steering reservoir and bracket, then install the bolts. Klj . 19 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Install the generator. For additional information, refer to
Section 414 - 02 .
10. Raise the vehicle. for additional information, refer to Section 100 - 02 .
11. Install the power steering pump. For additional information, refer to Section 211 - 02 .
12. Install the bolt and the body ground.
13. Install the nine bell housing bolts.
14. Install the starter. For additional information, refer to Section 303 - 06 .
15. NOTE: This will need to be done as the H- pipe is being positioned.
Connect the LH heated oxygen sensor.
16. NOTE: This will need to be done as the H- pipe is being positioned.
Connect the RH heated oxygen sensor. Klj . 4 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

29. Connect the connector.
30. Connect the fuse link.
31. Install and tighten the body ground.
32. Connect the power steering line. Klj . 8 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...