suspension FORD MUSTANG 2003 Workshop Manual

7.
CAUTION: Do not strike the toe link or the knuckle to disconnect the toe link. The
toe link or the knuckle can be damaged.
Using the special tool, disconnect the toe link (5K848) from the knuckle (5A968/5A969).
8. Remove the nut, bolt and the toe link. Discard the bolt and nut.
Installation 1. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
NOTE: The toe link bolt and nuts are of a torque prevailing design. A new bolt and new nuts
must be installed.
NOTE: Use a new cotter pin.
To install, reverse the removal procedure. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Coil
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
All vehicles
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle. For additional information, refer to Section 100 - 02 .
3. Disconnect the anti- lock sensor wire.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Hi-
Lift Jack
014- 00942 or Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Remove the bolt and the parking brake cable bracket. Discard the bolt.
Vehicles equipped with a 4.6L 2V engine 5. Remove the stabilizer bar (5A772). For additional information, refer to Stabilizer Bar in this
section.
All vehicles 6. Support the differential housing with a jack stand.
7. Position the special tool 014- 00942 under the rear lower suspension arm and bushing- to-axle
pivot bolt.
8. Remove and discard the pivot bolt and nut.
9. Remove the spring (5560). 1. Slowly lower the arm with the special tool 014- 00942.
2. Remove the rear spring and the rear spring insulators (5536). Installation Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

5. Remove the special tool 014-
00942.
6. Raise the suspension until the shock absorber is compressed to the alignment mark (curb height).
7. Tighten the lower arm- to-axle pivot bolt.
8. Lower the rear suspension and remove the jack stand.
Vehicles equipped with a 4.6L 2V engine
9. Install the stabilizer bar. For additional information, refer to Stabilizer Bar in this section.
All vehicles 10. Install the parking brake cable bracket and a new bolt. Klj . 4 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Support the No. 1 crossmember with a jack stand.
3. Remove both wheel and tire assemblies. For additional information, refer to Section 204 - 04 .
4. Remove both mufflers. For additional information, refer to Section 309 - 00 .
5. Remove the driveshaft. For additional information, refer to Section 205 - 01 .
6. Disconnect the parking brake cable and conduits from the parking brake levers.
7. Remove the clip and disconnect the parking brake cable and conduits from the rear brake calipers. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Rotunda Powertrain Lift
014-00765 or Equivalent Klj . 1 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Unclip the ABS sensor wires from the subframe.
13. Support the lower suspension arm and bushings (5A649) with jack stands.
14. Remove the nuts, bolts and disconnect the shock absorbers (18125) from the lower suspension
arm and bushings. Discard the bolts and nuts.
15. Lower the lower suspension arm and bushings and remove the jack stands.
16. Support the rear subframe using the special tool 014- 00765.
17. Remove and discard the nuts from the subframe front bolts. Klj . 3 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6. Remove the special tool 014-
00765.
7. Support the lower suspension arm and bushings with jack stands.
8. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
Connect the shock absorbers to the lower suspension arm and bushing and install new bolts
and nuts.
9. Clip the ABS sensor wires to the subframe.
10. Install the ABS sensors and the bolts. Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Connect the rear brake lines and install the bolts.
12. Connect the parking brake cable and conduits to the lower suspension arm and bushings and
install the bolts.
13. Connect the parking brake cable and conduits to the knuckles. 14. Connect the parking brake cable and conduits to the rear brake calipers and install the clips. Klj . 7 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Shock Absorber
Removal
WARNING: All vehicles are equipped with gas pressurized shock absorbers which will
extend unassisted. Do not apply heat or flame to the shock absorbers during removal or
component servicing. Failure to follow these instructions can result in personal injury.
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
CAUTION: When using a hoist that lifts the vehicle by the frame, install new shock
absorbers one at a time.
1. Open the luggage compartment lid. Position the carpet out of the way.
2. Remove and discard the retaining nut, washer and insulator assembly.
3. Raise the vehicle. For additional information, refer to Section 100 - 02 .
4. Remove the shock absorber (18125). 1. Remove and discard the bolt and nut.
2. Remove the shock absorber.
Installation SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Damper
Removal
CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Disconnect the damper from the axle. 1. Remove the bolt.
2. Disconnect the damper.
4. Remove the damper. 1. Remove the nut.
2. Remove the outer washer.
3. Remove the damper.
Installation 1. Make sure the inner washer is positioned on the stud. SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...