GEELY MK 2008 Workshop Manual

Chapter 8 Side Inner Panel TrimII. Removal & installation Side Quarter Trim Assy. Tips:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically. Mounting and taking down at right side is the same as the left side.I. Component ViewInterior & Exterior Trim and Accessory -Side Inner Panel Trim6-22Rear shelf trimPulley cover
Left A-pillar
upper trim
Front door frame left
weather strip
Left A-pillar lower
trimFront left doorsill shieldLeft B-pillar
lower trimRear left doorsill shieldRear left quarter lower trim Left C-pillar upper trim
Door frame left
weather strip
Left B-pillar upper
trim1. Detach right doorsill shield
Use the screwdriver to loosen 7 clasps and detach the right front
doorsill shield.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
2. Detach the left front doorsill shield.Clasp

Interior & Exterior Trim and Accessory -
Side Inner Panel Trim6-233. To remove the right rear doorsill shield.
Use screwdriver to loosen 6 buckles and detach the right rear
doorsill shield.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
4. Detach the left rear doorsill shield.
5. Detach the right front pillar trim
Use the screwdriver to loosen the clip and detach the right front
pillar lower trim.
Note:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
6. Detach the left front pillar trim.
7. Detach the right center pillar trim
Use the screwdriver to disconnect 2 clips, 4 buckles and detach
the right mid pillar lower trim.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
8. Detach the left center pillar lower trim.
9. Detach the right center pillar upper trim.
a. Use the screwdriver to open the pulley cover of the seat belt;
b. Unscrew the bolts and detach the belt rings from the car.
c. Use the screwdriver to loosen the clip and detach the right
center pillar upper trim.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
10. Detach the left center pillar upper trim.
11. Detach the backseat cushion assy.
12. Detach the backrest assy.Clasp ClaspClasp
clip
clip
clip

Interior & Exterior Trim and Accessory -Side Inner Panel Trim6-2413. Detach the luggage shelf assy.;
a. Detach the high-mounted stop lamp assy.;
b. Unfix three clips;
c.To pull the belt from the rift and detach the luggage shelf assy;
14. To remove the right quarter upper trim;
Use the screwdriver to unfasten 5 clips and 1 buckle and detach
the right quarter upper trim.
Notes:
Before using the screwdriver, apply the tape to cover its head.
15. Detach the left quarter upper trim.
16. Detach the right quarter lower trim.
a. Unfasten bolts and brackets.
b. Use the screwdriver to unfix 3 clips and detach the right quarter
lower trim.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
17. Detach the left quarter lower trim.
18. Detach the ring front pillar upper trim.
Use the screwdriver to unfix 2 clips and detach the ring front pillar
trim.
Notes:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
19. Detach the left front pillar upper trim.Clip clip
clip
clipClipcut

Chapter 9 Roof TrimI.Component View
II. Removal and Installation Roof Trim Assy. Tips:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.
Follow the same steps as you do with left side parts when installing the right side parts.
1. Remove side quarter trim assy.
2. Remove the right sun visor assy.;
Unfasten 2 screws;
3. Remove the sun visor assy..
Remove the left sun visor assy.;Right sun visor assy.
Sun visor holderLeft sun visor
assy.
Roof lamp
Lamp shadeInterior & Exterior Trim and Accessory -Roof Trim6-25Glasses box assembly
(without moonroof) Roof trim
Front roof handle assy.Rear roof handle assy.
Right roof handle assy.

Interior & Exterior Trim and Accessory -Roof Trim6-264. Remove the indoor roof lamp assy.
a. Use screwdriver to unfix the 4 buckles and remove the
lampshade;
Tips:
Wrap the sharp end of screwdriver up with adhesive tape before
operation.
b. Unfix 2 screws and the roof lamp assy.
5. Remove the handle assy.
a. Pull down the handle and take out 2 rubber plugs from the holes where two bolts are positioned;
b. Unfasten 2 screws and remove the handle assy.
6. Detach the sun visor tightener.
(Take down anti-clockwise the sun visor fastener.)
7. Remove the top trim
Use a special tool to remove 3 clips and remove the roof trim assy.
8. Installation is basically the reverse of removal.clip

Chapter 10 Front Door Interior TrimI.Component ViewFL door glass guide
FL door glass
FL door glass outer weatherstrip
FL door glass railFL door glass inner weatherstrip
FL door sealFL door muffler
FL door trim panel Switch panelFL/LH glass
regulatorFL door
corner trim
FL door inside handle Handle bracketFL door trim
board pull handleInterior & Exterior Trim and Accessory -Front Door Interior Trim6-27

Interior & Exterior Trim and Accessory -Front Door Interior Trim6-28II. Removal and installation of front door trim assembly Notes:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.
Installation and removal on the right side is identical with that on the left side.
1. Remove the left front door trim board pull handle
Unfix 1 screw by use of a crosshead screwdriver and then
unfasten the pull handle.
Tips:
Protect the pull handle from damage by wrapping the sharp end
of screwdriver up with adhesive tape before operation.
2. Remove the glass regulator switch assembly
a. Loosen the hook and the clamp by use of a slot-head screw-
driver and then unfasten the glass regulator switch;
b. Disconnect the switch;
c. Unfix 3 screws and the trim board.
3. Remove the left front door corner trim
a. Loosen 2 hooks and clamps by use of a slot-head screwdriver
and then unfasten the corner trim.
Tips:
Protect the corner trim from damage by wrapping the sharp end
of screwdriver up with adhesive tape before operation.
4. Remove left front door trim board
a. Unfix the screw and 2 clips;
b. Loosen 7 clips by use of a slot-head screwdriver and then pull
the door trim board backward to unfasten it.
Notes:
Protect the door trim board from damage by wrapping the sharp
end of screwdriver up with adhesive tape before operation.Hook
Clip
Clip
Hook
Clip

Interior & Exterior Trim and Accessory -Front Door Interior Trim6-295. Remove the left front door inside handle
Loosen 2 hooks, unfasten the left front door inside handle and
then disconnect 2 wires from the handle.
6. Peel off the rainproof film
7. Remove the speaker assembly
8. Remove the left front door glass and the left front door glass guide
Tips:
Protect the glass from scratch by inserting a cloth in the LF door
inner panel.
a. Unfix 2 bolts retaining the glass in place;
b. Remove the left front door glass;
c. Take out the glass guide.
9. Remove the left front door muffler
Unfix 2 bolts, 2 liners and the left front door muffler.
10. Remove the left front door glass regulator assembly
a. Disconnect the connector;
b. Unfix 6 bolts and left front door glass regulator assembly.
Caution
Be careful to prevent the glass regulator assembly from damage
when it is not supported by the bolts.
Notes:
Remove the left front door glass regulator assembly through the
service hatch.Hook
Hook

Chapter 11 Rear Door Interior TrimI. Component ViewRear left glass guide slot Left window end cover
Rear left window
guide track Rear left corner window weather strip
Rear left window inner weather stripRear Left corner glasses
Rear left windowRear left window
outer weather strip
Rear left window regulator
assembly
Rear left door weather strip Inside handle installation
bracket
gripsPower rear window switchRear left door inside handle
Rear left door
interior trim panel6-30Interior & Exterior Trim and Accessory -Rear Door Interior Trim

6-31II. Removal and Installation of the Rear Door Interior trim Tip:
Installation is basically the reverse of removal and different operation(s) in the process of installation, if any,
will be pointed out specifically.
The removal and installation at the right side are the same as those at the left side.
1. Remove the interior decorative plate handle of left rear door;
Remove a screw with the cross-head screwdriver, and then take
off the interior decorative plate handle of left-rear door.
Tip:
Wrap the head of screwdriver with belt before using it.
2. Remove the assembly of electric-driven window regulator switch;
a. Release the grips with the straight screwdriver, and then re
move the regulator switch off the decorative plate.
b. Disconnect the switch connector.
3. Remove the interior decorative plate of left rear door;
a. Remove the screws and buckles;
b. Release the 6 buckles with the straight screwdriver, and hold
upwards the interior decorative plate of rear-left door to re
move it.
Tip:
Wrap the head of screwdriver with belt before using it.
4. Remove the interior handle of left-rear door;
Release the 2 hooks, remove the interior handle of left-rear door,
and disconnect the 2 wires off the interior handle of left-rear door.
5. Remove off the rain-proof film on the door;clip
HookHookgripsInterior & Exterior Trim and Accessory -Rear Door Interior Trim