display GENESIS G80 2021 Premium Navigation Manual

267
Climate
conTrolling rear seaT climaTe
Powers on or off of the climate device of rear seat.
Press [Rear Climate Controls] on the climate screen.
a Rear seat set temperature
It sets the set temperature of the rear seat.
b AUTO
The air cooling and heating are automatically activated according to the set temperature.
c Blower position
Changes the seat blower position to up/down.
d Blower level
It displays the set blower level.
e Front climate controls
It sets the air conditioning temperature and air volume operating in the front seats.

270
Notification
notifiCation
This function can view the notification sent from Genesis connected services including the
navigation and map update information.
If there are more than two notifications to be displayed, moves to the detail of notification list
screen instead of the notification contents screen.
Press [Notification] on the home screen.
,noTe
䠐Up to 50 notifications can be saved.
䠐You must activate to the Genesis connected service to use this function.

277
Precautions for Safety
WARNING:
䠐Don’t use a cellular phone when you are driving. You must stop at a safe place to use a
cellular phone.
䠐The use of the navigation radio by no means relieves the driver of his/her responsibilities.
The highway code must always be observed. Always observe the current traffic situation.
䠐The applicable traffic regulations and the prevailing traffic situation always take precedence
over the instructions issued by the navigation system if they contradict one another.
䠐For traffic safety reasons, use the navigation system menus only before starting a journey or
when the vehicle is stationary.
䠐In certain areas, one-way streets and turn off and entry prohibitions (e.g. pedestrian zones)
are not recorded. In areas such as these the navigation system will issue a warning. Pay
particular attention to one-way streets and turn off and entry restrictions.
䠐The navigation system does not take the relative safety of the suggested routes into
consideration. Road blocks, building sites, height or weight restrictions, traffic or weather
conditions or other influences which affect the route safety or travel time are not taken into
consideration for the suggested routes. Use your own discretion in order to decide on the
suitability of the suggested routes.
䠐The current legal road traffic speed limit always takes priority over the values saved on
the data. It is impossible to provide an assurance that the speed values of the navigation
system will always match those of the current traffic regulations in every situation.
䠐Always observe the applicable legal speed limits the traffic regulations. The vehicle
speedometer must always be given priority for display of the vehicle speed.
䠐Do not rely exclusively on the navigation system when attempting to locate an emergency
service (hospital, fire service etc.). It cannot be guaranteed that all available emergency
services in your vicinity are saved in the database. Use your own discretion and abilities to
secure help in such situations.

281
General information
pLayaBLe fiLe Standard
pLayaBLe audio fiLe S tandard (uSB)
䠐Playable File Types: “.mp3”, “.wma”, “.mka”, “.wav”, “.flac”, “.ogg”, “.ac3”, “.dts”, “.m4a”
䠐Playable Codec Types: “MPEG-1 layer I, II, III”, “AC-3”, “AAC”, “WMA”, “PCM (WAV only)”,
“ADPCM (WAV only)”, “DTS”, “FLAC”
䠐Sampling Frequency: 8 - 48 KHz (MP3), 22.5 - 96 KHz (WMA), 8 - 192 KHz (PCM/WAV),
8 - 44 KHz (ADPCM/WAV), 32, 33.1, 48 KHz (AC-3), 8 – 192 KHz (AAC), 8 - 192 KHz (FLAC),
8 - 192 KHz (DTS)
䠐Bit rate: 8 - 320 Kbps (MP3), 20 - 320 Kbps (WMA) , 8 ~ 12.3Mbps (PCM/WAV), 8 ~
352.8Kbps (ADPCM/WAV), 8 – 320Kbps (AC-3) , 8 - 320 Kbps (AAC) , 8~4.6Mbps (FLAC,
ALAC, APE, TTA, AIFF)
pLayaBLe video fiLe S tandard
䠐Playable File Types: “.avi”, “.mpg”, “.mpeg”, “.mp4”, “.asf”, “.wmv", “mkv”
䠐Playable Codec Types: “MPEG-1”, “MPEG-2 simple profile – main level”,
“MPEG-2 main profile – low,main,high level”, “VC-1”,”AVC”,
”H.263 profile 0 ~ profile2”,”MPEG4 v2,v3”
䠐Playable resolution and frame rate: (MPEG-1) within 1280 x 720 30fps, 720 x 480p 30fps /
720 x 576p 25fps (H.263), 1920 x 1080 30fps (other supported Codec format)
plaYable sub TiTle sTandard
䠐Playable File Types: “.smi”,”.srt”
䠐Playable subtitle language : Korean, English, Japanese, Chinese etc
䠐When the file name of image and subtitles is different, subtitles may not be displayed.

282
Before Thinking the Product has Malfunctioned
before ThinKing The producT has
malfuncTioned
The current position as shown on the navigation may differ from the actual position under
the following conditions. The following occurrences are not malfunctions:
䠐When driving on Y-shaped roads with narrow angles the current position may be displayed
in the opposite direction.
䠐Within city streets, the current position may be displayed on the opposite side or on an off-
road position.
䠐When changing the zoom level from maximum to a different level, the current position may
become displayed on a different road.
䠐If the vehicle is loaded onto a ferry or a car transport vehicle, the current position may
become stalled on the last position prior to loading.
䠐When driving on a spiral-shaped road.
䠐When driving in mountain regions with sharp turns or sudden brakes.
䠐When entering a road after passing an underground parking structure, building parking
structure, or roads with many rotations.
䠐When driving in heavy traffic with frequent starts and stops.
䠐When driving under slippery conditions, such as heavy sand, snow, etc.
䠐When the tires have recently been replaced. (Especially upon use of spare or studless tires.)
䠐When using tires of improper size.
䠐When the tire pressure for the 4 tires are different.
䠐When the replacement tire is worn or used. (Especially studless tires having passed a
second season.)
䠐When driving near high-rise buildings.
䠐When a roof carrier has been installed.
䠐When a long distance route is calculated while driving on an expressway, in such cases,
continued driving will automatically enable the system to conduct map matching or use
updated GPS information to provide the current position. (In such cases, up to several
minutes may be required.)

284
Before you think the product is defective
before You ThinK The producT is
defecTiVe
1. Errors which occur during the operation or installation of the device may be mistaken as a
malfunction of the actual device.
2.
If you are having problems with the device, try the suggestions listed below.
3.
If the problems persist, contact your dealer.
Problem: There are small red, blue, or green dots on the screen
Possible Cause : Because the LCD is manufactured with technology requiring high point density, a pixel or lighting deficiency may occur within 0.01% of total pixels.
Problem: The sound or image is not working
Possible Cause :
-Has the Switch for the vehicle been turned to [ACC] or [ON]?
-Has the SYSTEM been turned OFF?
Problem: The screen is being displayed but sound is not working
Possible Cause :
-Has the volume been set to a low level?
-Has the volume been muted?
Problem: When the power is turned on, the corners of the screen are dark
Possible Cause :
-The display appearing somewhat dark after prolonged periods of use is normal with LCD panels. It is not a malfunction.
-If the screen is very dark, contact your nearest dealer for assistance.
Problem: Sound is working from only one speaker
Possible Cause : Are the positions of Fader or Balance sound controls adjusted to only one side?
Problem: The external device is not working
Possible Cause : Is the external device connected with a standard connector cable?
Problem: When turning power on, the most recent mode screen is not displayed
Possible Cause :
-Within modes that play files by reading external sources, such as USB or Bluetooth® streaming mode, the most recently played mode screen prior to turning off power may not properly load.
-If there is no the corresponding device is not connected, the mode operated prior to the most recent mode will operate.
-If the previous mode still cannot be properly played, the mode operated prior to that will operate.

285
Troubleshooting
TroubleshooTing
Problem: The power does not turn on.
䠐Possible Cause : The fuse is disconnected.
䠐Countermeasure:
-Replace with a suitable fuse.
-If the fuse is disconnected again, please contact your dealer.
䠐Possible Cause : Device is not properly connected.
䠐Countermeasure: Check to see that the device has been properly connected.
Problem: The system does not play.
䠐Possible Cause : The vehicle battery is low.
䠐Countermeasure: Charge the battery if the problem persists, contact your point of purchase or service center.
Problem: The image colour/tone quality is low.
䠐Possible Cause : The brightness, saturation, and contrast levels are not set properly.
䠐Countermeasure: Properly adjust the brightness, saturation, and contrast levels through Display Setup.
Problem: Sound does not work.
䠐Possible Cause : The volume level is set to the lowest level.
䠐Countermeasure: Adjust the volume level.
䠐Possible Cause : The connection is not proper.
䠐Countermeasure: Check to see that the device has been properly connected.
䠐Possible Cause : The device is currently fast-forwarding, rewinding, scanning, or playing in slow mode.
䠐Countermeasure: The sound will not work when the device is fast-forwarding, rewinding, scanning, or playing in slow mode.
Problem: The sound or image quality is low.
䠐Possible Cause : Vibration is occurring from where the conversion switch has been installed.
䠐Countermeasure: The sound may be short circuited and the image distorted if the device vibrates.

295
trademarks and licenses
copYrighT for brand icon
The marks of companies displayed by this product to indicate business locations are the
marks of their respective owners. The use of such marks in this product does not imply any
sponsorship, approval, or endorsement by such companies of this product.
copYrighT for junc Tion View
Junction View Data provided by ZENRIN USA, INC. Copyright(C) 20XX, All rights Reserved.
abouT map updaTes
You can contact your dealer.
Information:
This product requires regular updates for new functions and map updates. Updating may
require up to 1 hour depending on the data size.
Turning off the power or ejecting the USB during the update process may result in damage to
the system. Make sure to keep the ignition on and wait until updating is complete.
CAUTION:
䠐The use of an uncertified USB may result in damage to the system due to heat related
deformation.
䠐Product malfunctions caused by the use of an uncertified cards shall not be covered within
the product warranty.
䠐Repeatedly connecting/disconnecting the USB in a short period of time may cause damage
to the device.