torque GREAT WALL FLORID 2008 Repair Manual

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual268
Sunroof Assembly
Components
N·m: Specified torque
Sunroof panel
Sunroof window weatherstrip
Movable sun visor
Slider
Upper trim strip
Lower trim strip
Roof drip channel
Guide device latch hook
End piece
Guide rail assembly
Bolt
Spring
Wind guard
Bolt
Rear guide device
Air guide plate
Spacing tube
Drive device
4.5
3.5

Downloaded from www.Manualslib.com manuals search engine GWFLORID Maintenance Manual270
Sunroof panel removal
1. Move sun visor to the back position.
2. Open sunroof in the slanted position.
3. Adjust the lower trim strip.
Loosen the front part of the lower trim strip in the direction
of car's interior to take the rear part off the hook.
4. Adjust the upper trim strip.
Loosen the front and middle parts of the upper trim strip to
take the rear part off the hook.
5. Remove the sunroof's left and right side mounting bolts
6. Pull up the sunroof panel.
Caution: After removing the sunroof panel, do not turn
the sunroof switch to the "Open" position. Because the
window panel will no longer press the roof drip channel
at this time, the roof drip channel will tilt into the sun-
roof.
Sunroof panel installation
The window panel must be installed at the initial position
(window panel is closed).
1. Window panel location
The mark (indicated by the arrow) on the top of rear guide
device, which is on the window panel's two sides, must be
level with the "a" mark on the air guide plate.
The air guide plate must be installed in the guide rail (cannot
be manually moved).
If there is no guide rail on the air guide plate, please adjust
it.
2. Place the sunroof from the top down
3. Adjust the clearance
Insert six sheets of paper, each of about 0.3 mm thickness,
around the window panel to make sure that clearances
around the panel is symmetrical.
4. Tighten the mounting bolt
Tightening torque: 4.5 N·m.
Sunroof panel adjustment
1. Adjust the front part.
a = 0-1 mm, lower than the level position of the sunroof.
The arrow refers to the driving direction (facing forward).
Lower trim strip
Upper trim strip
Mounting boltMounting bolt
Guide device
Air guide plate

Downloaded from www.Manualslib.com manuals search engine 273Vehicle Body
Adjust the initial position of drive device
Precondition:
(a) Remove the drive device, but leave the electric plug-in
connected.
(b) The sunroof is on the initial position. Sunroof panel has
been installed correctly.
Caution: The gear of drive device cannot contact
anything while adjusting.
1. Select the "Tilt Sunroof" function (position 1) with the
rotary switch.
2. Select the "Close Sunroof" function (position 2) with the
rotary switch.
3. Select the "Open Sunroof" function (position 3) with the
rotary switch.
4. Select the "Close Sunroof" function (position 2) with the
rotary switch.
5. Mark "1" is shown on the observation panel.
6. The drive device is on the initial position.
Parallel operation condition examination
1. The mark (indicated by the arrow) above the rear guide
device on the window panel's two sides must be level
with the "a" mark on the air guide plate.
2. The air guide plate must be installed in the guide rail
(cannot be manually moved).
Adjust the parallel operation condition
Instructions: Only when the sunroof is on the initial position,
and the drive device and window panel are removed, can the
parallel operation conditions be adjusted.
1. The mark (indicated by the arrow) above the rear guide
device on the window panel's two sides must be level
with the "a" mark on the air guide plate.
2. The air guide plate must be installed in the guide rail
(cannot be manually moved).
3. From the front, slide the top of the guide device and
position it between the two symbols.
4. Position.
Mount the drive device at this position (initial position) and
then examine the initial position.
Sunroof assembly installation
1. Install the sunroof assembly into the ceiling opening
with the help of an assistant.
2. The three dowel pins ("B" position on the diagram)
must be placed in the location holes.
3. Check the condition of the circuit connection.
4. Install the bolts.
Tighten them successively from the left and right side to the
rear part of the sunroof drive device. Tightening torque for
all is 8 N·m.
5. Install the outlet pipe.
6. Insert the drive device plug.
Air guide plate
Guide device
Sunroof assembly
Plastic gasket
Mounting bolt
Drive device
B
BB