brake HONDA INTEGRA 1998 4.G Service Manual

l,
Wheel Alignment
Turning Angle Inspection
NOTE: Use commercially-available computerized four
wheel alignment equipment to measure wheel align-
ment (caster, camber, toe, and turning angle). Follow
the equioment manufacturer's instructions.
1. Turn the wheel right and left while applying the
brake, and measure the turning angle of both
wneels.
Turning angle:
lnward whsol: 36'00't 2"
Outward wheel: 30'30'{rotorencel
lf the turning angle is not within the specifications.
check for bent or damaged suspension compo-
nenrs.
18-6

Knuckle/Hub
lllustrated Index
Note these items during installation:
. Before installing the brake disc, clean the mating surfaces of the front hub and the brake disc.o Before installing the wheel, clean the mating surfaces ofthe brake disc and the wheel.
All except Typs R Model3:
CASTLE NUT12 x 1.25 nn
COTTER PINReplace.
WHEEL BEARINGReplace.
LOWER EALL JOINTBeplacement, page 18 17
Replacement, page l8-14
CIRCLIP
SCREW5x0.8mm
FRONT HUB@tV,/- ai.1eetL.rotNtgoot/ Y\
| \conen erru
I Reptace.
ICASTLE NUT12 x 1.25 fin
BRAKE OISCReplacement, page 18-1 1Inspection, section 19
6 mm BRAKE DISC RET
WHEEL
(cont'd)
12 x 1.5 m.n
18-9

Front Suspension
Knuckle/Hub {cont'd}
lllustrated lndox
Note these items during replacement:
. Before installing the brake disc, clean the mating surfaces of the front hub and brake disc'
. BeJore instslling the wheel, clean the mating surfaces ofthe brake disc and wheel'
Type R Modsl:
CASTLE NUT12 x 1.25 mm
CAUPER MOUNTING EOLT12x 1.25 fim
COTTER PINReplace.
WHEEL BEARINGReplace.Replacement, Page 18-14
SPLASH GUARO
LOWER BALL JOINTReplacement, page 18-17SCREW5x0.8mm
I,
rl
I
I'i.
1l,ltl
CASTLE NUT12 x 1,25 mmSPINDLE NUT2. x 1.5 mfi
6 mm BRAKE DISC RETAINING SCREW
WHEEL NUT12 x'1.5 mm
18-10

1.
Knuckle Removal
Loosen the wheel nuts slightly.
Raise the front of vehicle. and support it with safetystands in the proper locations {see section l ).
B€move the wheel nuts and front wheel.
SPINDLE NUT22 x 1.5 mmReplace.
Raise the locking tab on the
remove the nut.
spindle nut. then
Remove the brake hose mounting bolts.
Remove the caliper bracket mounting bolts, andhang the caliper to one side.
CAUTION: To pravant accidental damage to thgcaliper or braks hoso, use a shqrt piece of wirs tohsng the c8liper flom the undercarriage.
CALIPER BRACKET MOUNTING BOLTS12 x 1.25 mm
7, Remove the 6 mm brake disc retaining screws.
BRAKE DISCCheck for wear and rust.Inspection, section j9.
8. Screw the two I x L25 mm bolts into the disc topush it awav from the hub.
NOTE: Turn each bolt two turns at a time to pre-
vent cocking the disc excessively.
Remove the brake disc from the knuckle.
Check the front hub for damage or cracks.
Remove the wheel sensor wire bracket, thenremove the wheel sensor lrom the knuckle (for vehi-cles with ABS).
NOTE: Do not disconnect the wheel sensor connec-ror.
4.
6.
10.
11.
WHEEL SENSOFWIRE BRACKET
FRONT WHEEL
8 x 1.25 mm BOLTS
WHEEL SENSOR(cont'd)

Front Suspension
Knuckle/Hub (cont'd)
Knuckle lnstallation
1. lnstall the knuckle on the driveshaft.
2. lnstall the knuckle on the lower arm and the tie-rod,
then tighten the nuts and install new cotter pins.
CAUTION:
. Be carelul not to damage tho ball ioint boot.
a Torque the castls nut to the lowel torque spgci-
fication, then tight€n it only far enough to align
the slot with the pin hole. Do not align the nut
by loosening.
NOTE: Wipe off the grease before tightening the
nut at the ball joint.
NUT
ri
10 x 1.25 mm4il N.m (4.{ kgtm,32lbf.ftl
On reassembly,bend the cotter pin
as shown.
CASTLE NUT12 x 1 .25 mm49 - 59 N.m (5.0 - 6.0 kgf m, 36 -,|i| lbf ft)
3. Install the knuckle on the upper arm, then tighten
the castle nut and install a new cotter Din.
COTTER PINReplace.On reassembly,bend the cotter pin
CASTLE NUT12 x 1.25 mm39 - 47 N.m{4.0 - 4.8 kgf.m,29 - 3s rbr.ft)
;
, 'ar
COTTER PIN
18-16
4.Install the wheel sensor with the sensor mounting
bolts (tor vehicles with ABS).
lnstall the sensor wire with the two 5 mm bolts (for
vehicles with ABS).
NOTE: Be careful when installing the sensors to
avoid twisting wires.
6 mm BOLTS9.8 N.m 11.0 kgf.m,7 lbf.ftl
v_)
SENSOR MOUNTINGBOLTS9.8 N.m (1.0 kgf.m,7.2 lbl.ftl
6. lnstall the brake disc with the 6 mm brake disc retain-
Ing screws.
NOTE: Before installing the brake disc, clean the
mating surfaces of the front hub and the brake disc.
6 mm BRAKE DISCRETAINING SCREWS9.8 N.m 11.0 kgl.m, 7.2 lbf'ftl

Lower Ball Joint Replacement
7.Install the brake caliper with the caliper bracket
mounting bolts.
Install the brake hose with the brake hose mounting
bolts.
CAUTION: Bo careful not to twist the hose more
than ngcsssary.
BRAKE HOSEMOUNNNG BOLTS
CALIPER BRACKET MOUNTING BOLTS
12 x 1.25 mm108 N.m (11.0 kgf m,80 lbtftl
\9.
10.
lnstall a new spindle nut, then tighten the nut.
Installthe wheel with the wheel nuts
NOTE: Before installing the wheel, clean the mating
surfaces of the brake disc and the wheel.
FRONT WHEEL
WHE€L NUT12 x 1.5 mm108 N.m {11.0 kgf.m,80 lbtft)22 x 1.5 mm181 N.m 118.5 kgt m, 134 lbl.ftlReplace.
NOTE: After tightening, us€ a drift tostake the spindle nut shoulder againstthe driveshaft.
11. Check the tront wheel alignment and adjust if nec-
essary (see page l8-4).
1.
2.
4.
5.
Remove the knuckle (see page 18-11).
Remove the boot by prying the set ring off.
Check the boot for deterioration and damage,
replace if necessary.
Install the special tools on the ball joint and tighten
the castle nut.
Position the special tools over the ball joint asshown then set the assembly in a vise. Press the
ball joint out of the knuckle.
07JAF - SH20200
Place the balljoint in position by hand.
Install the special tools over the ball joint as shown,
then press the ball joint in.
BALL JOINT INSTALLER BASE07965 - 5800200
6.
7.
(cont'd)
18-17

Front Damper
FLANGE BOLT10 x'1.25 mm
1.
4.
Removal
Remove thefrontwheels (see page 18-'11).
Remove the brake hose mounting bolts from the
damper.
Remove the flange bolt.
Remove the flange bolt and self-locking nut, then
remove the damper fork.
MOUNTING BOLT{8 x 16 mm)
Disassembly/lnspection
Disassembly
1. Compress the damper spring with the spring com-
pressor according to the manufacturer's instruc-
tions. then remove the self-locking nut.
CAUTION: Do nol compros3 tho 3pring morc than
nocessary to romovo th€ nut.
DAMPER FORK
FLANGE BOLT
SELF.LOCKING10 x 1.25 mmReplace.
COMPRESSORIlComm.rci.lly .Yrll.blclARAN|CKO T/N MST-580A, T/N 72IX',or aouivalant
Remove the damper by removing the two flange
n uts.
2, Remove the spring compressor, then disassemble
the damper as shown on the neld page.
Inspection
1. Reassemble all parts, exceptthe spring,
2, Push on the damper as shown.
3. Check for smooth operation through a full stroke,
both compression and extension.
NOTE: The damper should move smoothly. lf it
does not (no compression or no extension), the gas
is leaking, and the damper should be replaced.
Check for oil leaks, abnormal noises or binding dur-
ing these tests.
BMKE HOSE MOUNTING BOLT(8 x 20 mml
/GS, GSR, Type R Mod6ls: \l8x25mm I
18-22

1.Loosely install the
aligning tab facing
two flange nuts,
damper on the frame with
inside, then loosely install
the
the
2.Install the damper fork over the driveshaft and onto
the lower arm. Install the front damper in the
damper fork so the aligning tab is aligned with the
slot in the damper fork.
Loosely install the flange bolt.
Loosely install a new self locking nut with the
flange bolt.
Raise the knuckle with a floor jack until the vehicle
just lifts off the safety stand.
@ The ltoor jack must be securely posi-
tioned or personal iniury may result.
Tighten the flange bolt.
Tighten the self-locking nut.
Tighten the flange nuts on the top of the damper to
3.
FLANGE NUTS10 x'1.25 mm49 N m 15.0 kgt m,36 lbtft)Tighten to this torque in step 8.
4.
5.
6.
7.
8.
the specified torque.
9. lnstall the brake hose mounts with the brake hose
mounting bolts.
ERAKE HOSE MOUNTING BOLT18 x 20 mml
/GS, GsR, Type R Models: \lgr25-- ,22 N.m 12.2 kgt m, 16 lbf.ft)BRAKE HOSE MOUNTING BOLT{8 x 16 mm)22 N.m {2.2 kgl.m, 16lbtft}
FLANGE BOLT
SELF.LOCKING NUT12 x L25 mm64 N.m (6.5 kgt m, 47 lbI.ftl
BOLT10 x 1.25 mm,|:} N.m {4.4 kstm, 32lbtft}
10. Install the front wheel (see page 18-17).
DAMPER
ALIGNING TA8
lnstallation
8-25

Hub Bearing Unit
lllustrated Index
Note the following during installation;
. Before installing the brake disc, clean the mating surfaces ofthe rear hub and the brake disc.
. Before installing the wheel, clean the mating surfaces ofthe brake disc and the wheel.
All oxcopt Typo R Modol3:
6 mm FLANGE BOL
SPINDLE22 x 1.5 mmReplace.
6 mm BRAKE DISC RETAINING
WHEEL12 x 1.5 mm
(cont'd)
18-27

Rear Suspension
Hub Bearing Unit (cont'd)
Type R Model:
TRAIUNG ARMREAR WHEELSPLASH GUARDHUB BEARING UNIT
SPINDLE WASHER
SPIND1I NUT22 x 1.5 mm
HUB CAP.Replace.
6 mm FLANGE BOLT
6 mm BRAKE DISC RETAINING SCREW
WHEEL NUT12 x 1.5 mm
II
18-28