sel HYUNDAI PALISADE 2022 Owners Manual

5-98
Driving your vehicle
Blind-Spot Collision Warning
settings
Setting features
Blind-Spot Safety
With the engine on, select or dese-
lect ‘Driver assistance →Blind-spot
safety’ from the Settings menu to set
whether or not to use each function.
OTM070096N
Take the following precautions
to maintain optimal perform-
ance of the detecting sensor:
Never disassemble the rear
corner radar or radar assem-
bly, or apply any impact on it.
If there is impact on the rear
corner radar or near the radar,
even though the warning mes-
sage does not appear on the
cluster, Blind-Spot Safety sys-
tem may not operate properly.
Have the vehicle inspected by
an authorized HYUNDAI deal-
er.
If the rear corner radars have
been replaced or repaired,
have the vehicle inspected by
an authorized HYUNDAI deal-
er.
Use only genuine parts to
repair the rear bumper where
the rear corner radar is locat-
ed.
Do not apply license plate
frame or objects, such as a
bumper sticker, film or a
bumper guard near the rear
corner radar.
The function may not work
properly if the bumper has
been replaced, or the sur-
roundings of the rear corner
radar has been damaged or
paint has been applied.
If a trailer, carrier, etc. is
installed, it may adversely
affect the performance of the
rear corner radar or the func-
tion may not operate.CAUTION
For more details on the precau-
tions of the front view camera,
refer to “Forward Collision-
Avoidance Assist (FCA)” sec-
tion in chapter 5.
CAUTION

5-99
Driving your vehicle
5
- If ‘Active Assist’ is selected, thefunction will warn the driver with a
warning message, an audible
warning, steering wheel vibration
and braking assist will be applied
depending on the collision risk lev-
els.
- If ‘Warning Only’ is selected, the function will warn the driver with a
warning message, an audible
warning and steering wheel vibra-
tion depending on the collision risk
levels. Braking will not be assisted.
- If ‘Off’ is selected, the function will turn off. If you press the Blind-Spot Safety
button while 'Active assist' or
'Warning only' is selected the indi-
cator on the button will turn off and
the system will deactivate.
If you press the Blind-Spot Safety button while the system is cancelled
the indicator on the button illumi-
nates and the function activates. In
this case, the function returns to the
state before the engine was turned
off.
When Blind-Spot Collision-
Avoidance Assist is initially turned
on and when the engine is turned
off then on again while the function
is in activation, the warning light
will illuminate for 3 seconds on the
outside rearview mirror. When the engine is restarted with
the function off, the ‘Blind-Spot
Safety System is Off’ message will
appear on the cluster.
If you change the setting from ‘Off’ to
‘Active Assist’ or ‘Warning Only’, the
warning light on the outside rearview
mirror will blink for three seconds.
In addition, if the engine is turned on,
when the function is set to ‘Active
Assist’ or ‘Warning Only’, the warning
light on the outside rearview mirror
will blink for three seconds.
OLX2059032LOTM070097N

5-100
Driving your vehicle
Information
If the engine is restarted, Blind-Spot
Safety system will maintain the last
setting.Warning Timing
With the engine on, select ‘Driver
assistance →Warning timing’ from
the Settings menu to change the ini-
tial warning activation time for Blind-
Spot Safety system.
When the vehicle is first delivered,
Warning Timing is set to ‘Normal’. If
you change the Warning Timing, the
warning time of other Driver
Assistance systems may change.
Warning Volume
With the engine on, select 'Driver
Assistance →
Warning Volume' from
the Settings menu to change the
Warning Volume to 'High', 'Medium',
'Low' or 'Off' for Blind –Spot Collision
Avoidance Assist.
However, even if 'Off' is selected,
Blind-Spot Collision-Avoidance
Assist's Warning Volume will not turn
off but the volume will sound as
'Low'.
If you change the warning volume,
the Warning Volume of other Driver
Assistance systems may change.
iOTMA058089
If ‘Warning Only’ is selected,
braking is not assisted.
If ‘Off’ is selected, the driver
should always be aware of the
surroundings and drive safe-
ly.
WARNING
ONX4E070090

5-101
Driving your vehicle
5
Blind-Spot Collision-
Avoidance Assist operation
Warning and control
Vehicle detection
To warn the driver a vehicle isdetected, the warning light on the
outside rearview mirror and head-
up display (if equipped) will illumi-
nate.
Blind-Spot Collision-Avoidance Assist will operate when your vehi-
cle speed is above 12 mph (20
km/h) and the speed of the vehicle
in the blind spot area is above 7
mph (10 km/h).
Collision Warning
Collision warning will operate whenthe turn signal is turned on in the
direction of the detected vehicle.
If ‘Warning Only’ is selected from the Settings menu, the collision
warning will operate when your
vehicle approaches the lane the
blind spot vehicle is detected.
To warn the driver of a collision, the warning light on the outside
rearview mirror and head-up dis-
play (if equipped) will blink. At the
same time, an audible warning will
sound and the steering wheel will
vibrate.
When the turn signal is turned off or you move away from the lane,
the collision warning will be can-
celed and the function will return to
vehicle detection state.

The setting of the Warning
Timing and Warning Volume
applies to all functions of the
Blind-Spot Safety system.
Even though ‘Normal’ is
selected for Warning Timing, if
the vehicles approaches at
high speed, the initial warning
activation time may seem late.
Select ‘Later’ for Warning
Timing when traffic is light
and when driving speed is
slow.CAUTION
ORG3070025

5-112
Driving your vehicle
Rear Cross-Traffic Collision
Warning settings
Setting features
Rear Cross-Traffic Safety
With the engine on, select ‘Driver
Assistance →Parking Safety →
Rear Cross-Traffic Safety’ from the
Settings menu to turn on Rear
Cross-Traffic Collision Warning and
deselect to turn off the function.
Warning Timing
With the engine on, select ‘Driver
Assistance →Warning Timing’ from
the Settings menu to change the ini-
tial warning activation time for Rear
Cross-Traffic Collision Warning.
When the vehicle is first delivered,
Warning Timing is set to ‘Normal’. If
you change the Warning Timing, the
warning time of other Driver
Assistance systems may change.
OTM070194N
OLX2071064N
When the engine is restarted,
Rear Cross-Traffic Collision
Warning will always turn on.
However, if ‘Off’ is selected after
the engine is restarted, the driv-
er should always be aware of
the surroundings and drive
safely.
WARNING

5-113
Driving your vehicle
5
Warning Volume
With the engine on, select 'Driver
Assistance →
Warning Volume' from
the Settings menu to change the
Warning Volume to 'High', 'Medium',
'Low' or 'Off' for Rear Cross-Traffic
Collision Warning.
However, even if 'Off' is selected,
Forward Collision-Avoidance Assist's
Warning Volume will not turn off but
the volume will sound as 'Low'.
If you change the warning volume,
the Warning Volume of other Driver
Assistance systems may change.
Information
If the engine is restarted, Warning
Timing and Warning Volume will
maintain the last setting.
Rear Cross-Traffic Collision
Warning operation
Warning
Rear Cross-Traffic Collision Warning
will warn the driver when a collision
is imminent.
i
ORG3070025/OTM070168
OLX2058044L
The setting of the Warning
Timing and Warning Volume
applies to all functions of the
Rear Cross-Traffic Safety.
Even though ‘Normal’ is
selected for Warning Timing, if
the vehicles from the left and
right side approaches at high
speed, the initial warning acti-
vation time may seem late.
Select ‘Later’ for Warning
Timing when traffic is light
and when driving speed is
slow.
CAUTION
ONX4E070090

5-120
Driving your vehicle
Rear Cross-Traffic Collision-
Avoidance Assist
Setting features
Rear Cross-Traffic Safety
With the engine on, select ‘Driver
Assistance →Parking Safety →
Rear Cross-Traffic Safety’ from the
Settings menu to turn on Rear
Cross-Traffic Collision-Avoidance
Assist and deselect to turn off the
function.
Information
Settings for Rear Cross-Traffic
Collision-Avoidance Assist include
Rear Cross-Traffic Collision Warning
and Rear Cross-Traffic Collision-
Avoidance Assist.
Warning Timing
With the engine on, select ‘Driver
Assistance →Warning Timing’ from
the Settings menu to change the ini-
tial warning activation time for Rear
Cross-Traffic Collision-Avoidance
Assist.
When the vehicle is first delivered,
Warning Timing is set to ‘Normal’. If
you change the Warning Timing, the
warning time of other Driver
Assistance systems may change.i
OTM070194N
When the engine is restarted,
Rear Cross-Traffic Collision-
Avoidance Assist will always
turn on. However, if ‘Off’ is
selected after the engine is
restarted, the driver should
always be aware of the sur-
roundings and drive safely.
WARNING
OTMA058089

5-121
Driving your vehicle
5
Warning Volume
With the engine on, select 'Driver
Assistance →
Warning Volume' from
the Settings menu to change the
Warning Volume to 'High', 'Medium',
'Low' or 'Off' for Forward Collision-
Avoidance Assist.
However, even if 'Off' is selected,
Forward Collision-Avoidance Assist's
Warning Volume will not turn off but
the volume will sound as 'Low'.
If you change the warning volume,
the Warning Volume of other Driver
Assistance systems may change.
Information
If the engine is restarted, Warning
Timing and Warning Volume will
maintain the last setting.
Rear Cross-Traffic Collision-
Avoidance Assist operation
Warning and control
Rear Cross-Traffic Collision-
Avoidance Assist will warn and con-
trol the vehicle depending on colli-
sion level: ‘Collision Warning’,
‘Emergency Braking’ and ‘Stopping
vehicle and ending brake control’.
i
The setting of the Warning
Timing and Warning Volume
applies to all functions of the
Rear Collision-Avoidance
Assist.
Even though ‘Normal’ is
selected for Warning Timing, if
the vehicles from the left and
right side approaches at high
speed, the initial warning acti-
vation time may seem late.
Select ‘Later’ for Warning
Timing when traffic is light
and when driving speed is
slow.
CAUTION
ONX4E070090

5-131
Driving your vehicle
5
Lane Following Assist is designed to
help detect lane markings and/or
vehicles on the road, and assists the
driver’s steering to help keep the
vehicle between lanes.Detecting sensor
[1]: Front view camera
The front view camera is used as a
detecting sensor to detect lane
markings and front vehicles.
Refer to the picture above for the
detailed location of the detecting
sensor.
Lane Following Assist settings
Setting features
The driver can turn on Lane
Following Assist with the vehicle on
and by selecting 'User settings →
Driver assistance → Driving Assist
→ Lane Following Assist' in the clus-
ter LCD display. Lane Following
Assist deactivates, when the driver
deselects the function setting from
the User Settings mode in the cluster
LCD display. The set-up of Lane
Following Assist will be maintained,
as selected, when the vehicle is
restarted.
L L A A N N E E F F O O L LL LO O W W I IN N G G A A S SS SI IS S T T ( ( L L F F A A ) ) ( ( I IF F E E Q Q U UI IP P P PE ED D ) )
OLX2051137L
For more details on the precau-
tions of the front view camera,
refer to “Forward Collision-
Avoidance Assist (FCA)” sec-
tion in this chapter.
CAUTION
5

5-132
Driving your vehicle
Warning Volume
With the engine on, select ‘Driver
Assistance →Warning Volume’ from
the Settings menu to change the
Warning Volume to ‘High’, ‘Medium’,
‘Low’ for Lane Following Assist.
If you change the Warning Volume,
the warning volume of other Driver
Assistance systems may change.
Lane Following Assist opera-
tion
Warning and control
Lane Following Assist
If the vehicle ahead and/or both lane
markings are detected and your
vehicle speed is below 112 mph (180
km/h), the green indicator light
will illuminate on the cluster, and
Lane Following Assist will help the
vehicle stay in lane by assisting the
steering wheel.
When the steering wheel is not
assisted, the white indicator
light will blink and change to
grey.
CAUTION
OTM070141N
OLX2051148N