stop start INFINITI FX 2010 Repair Manual

back up slowly. If possible, have someone
guide you when you are backing up.
Always block the wheels on both vehicle and
trailer when parking. Parking on a slope is not
recommended; however, if you must do so:
CAUTION
If you move the shift selector lever to the P
(Park) position before blocking the wheels and
applying the parking brake, transmission dam-
age could occur.
1. Apply and hold the brake pedal.
2. Have someone place blocks on the down- hill side of the vehicle and trailer wheels.
3. After the wheel blocks are in place, slowly release the brake pedal until the blocks
absorb the vehicle load.
4. Apply the parking brake.
5. Shift the transmission into P (Park).
6. Turn off the engine.
To drive away:
1. Apply and hold the brake pedal.
2. Start the engine.
3. Shift the transmission into gear.
4. Release the parking brake. 5. Drive slowly until the vehicle and trailer
are clear from the blocks.
6. Apply and hold the brake pedal.
7. Have someone retrieve and store the blocks.
● When going down a hill, shift into a lower
gear and use the engine braking effect.
When going up a long grade, downshift the
transmission to a lower gear and reduce
speed to reduce chances of engine overload-
ing and/or overheating.
● If the engine coolant rises to an extremely
high temperature when the air conditioning
system is on, turn off the air conditioner.
Coolant heat can be additionally vented by
opening the windows, switching the fan
control to high and setting the temperature
control to the HOT position.
● Trailer towing requires more fuel than nor-
mal circumstances.
● Avoid towing a trailer for the first 500 miles
(800 km).
● Have your vehicle serviced more often than
at intervals specified in the recommended
maintenance schedule in the INFINITI Service
and Maintenance Guide.
● When making a turn, your trailer wheels will
be closer to the inside of the turn than your vehicle wheels. To compensate for this,
make a larger than normal turning radius
during the turn.
● Crosswinds and rough roads will adversely
affect vehicle/trailer handling, possibly
causing vehicle sway. When being passed by
larger vehicles, be prepared for possible
changes in crosswinds that could affect ve-
hicle handling. If swaying does occur, firmly
grip the steering wheel, steer straight
ahead, and immediately (but gradually) re-
duce vehicle speed. This combination will
help stabilize the vehicle. Never increase
speed.
Do the following if the trailer begins to sway:
1. Take your foot off the accelerator pedal to allow the vehicle to coast and steer as
straight ahead as the road conditions
allow. This combination will help stabilize
the vehicle.
– Do not correct trailer sway by steering orapplying the brakes.
2. When the trailer sway stops, gently apply the brakes and pull to the side of the road
in a safe area.
3. Try to rearrange the trailer load so it is balanced as described earlier in this sec-
tion.
9-26Technical and consumer information
—
—
08/03/09—pattie


You may notify INFINITI by contacting our
Consumer Affairs Department, toll-free,
at 1-800-662-6200.A vehicle equipped with All-Wheel Drive (AWD)
should never be tested using a two wheel
dynamometer (such as the dynamometers used
by some states for emissions testing), or similar
equipment. Make sure you inform test facility
personnel that your vehicle is equipped with
AWD before it is placed on a dynamometer.
Using the wrong test equipment may result in
transmission damage or unexpected vehicle
movement which could result in serious vehicle
damage or personal injury.
Due to legal requirements in some states/ areas
or provinces, your vehicle may be required to be
in what is called the “ready condition” for an
Inspection/Maintenance (I/M) test of the emis-
sion control system.
The vehicle is set to the “ready condition” when
it is driven through certain driving patterns.
Usually, the “ready condition” can be obtained
by ordinary usage of the vehicle.
If a powertrain system component is repaired or
the battery is disconnected, the vehicle may be
reset to a “not ready condition”. Before taking
the I/M test, check the vehicle’s
inspection/maintenance test readiness condi-
tion. Push the ignition switch to the ON position
without starting the engine. If the Malfunction
Indicator Light (MIL) comes on steady for 20
seconds and then blinks for 10 seconds, the I/Mtest condition is “not ready”. If the MIL does not
blink after 20 seconds, the I/M test condition is
“ready”.
If the MIL indicates the vehicle is in a “not
ready” condition, drive the vehicle through the
following pattern to set the vehicle to the
“ready condition”. If you cannot or do not want
to perform the driving pattern, an INFINITI re-
tailer can conduct it for you.
WARNING
Always drive the vehicle in a safe and prudent
manner according to traffic conditions and
obey all traffic laws.
1. Start the engine. Allow the engine to idle
until the engine coolant temperature
gauge needle points between the C and H
(normal operating temperature).
2. Accelerate the vehicle to 55 MPH (88 km/h), then quickly release the accelera-
tor pedal completely and keep it released
for at least 10 seconds.
3. Quickly depress the accelerator pedal for a moment, then drive the vehicle at a
speed of 53 to 60 MPH (86 to 96 km/h) for
at least 9 minutes.
4. Stop the vehicle. Leave the engine run- ning.
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST
9-30Technical and consumer information
—
—
08/03/09—pattie


10 Index
A
ABS (Anti-lock Braking System) ........5-76
Adaptive front lighting system (AFS) .....2-38
Advanced air bag system ...........1-45
Aiming control, Adaptive front lighting
system (AFS) ................. .2-38
Air bag system Advanced air bag system .........1-45
Front passenger air bag and status
light ..................... 1-47
Front-seat mounted side-impact
supplemental air bag system .......1-50
Roof-mounted curtain side-impact and
rollover supplemental air bag system . . 1-50
Air bag warning labels .............1-53
Air bag warning light ..........1-53 , 2-17
Air cleaner housing filter ...........8-19
Air conditioner Advanced Climate Control System
(ACCS) ................... .4-44
Air conditioner service ..........4-46
Air conditioner specification label ....9-13
Air conditioning system refrigerant and
lubricant recommendations .......4-46
Automatic climate control ........4-40
In-cabin microfilter ............4-45
Operation (See automatic climate
control) ................... 4-40
Alarm, How to stop alarm
(see vehicle security system) .........2-31Alcohol, drugs and driving
...........5-7
All-wheel drive (AWD) .............5-69
All-wheel drive (AWD) warning light .....2-13
Antenna .................... .4-90
Anti-lock Braking System (ABS) ........5-76
Anti-lock braking system (ABS) warning
light ...................... .2-13
Appearance care Exterior appearance care ..........7-2
Interior appearance care ..........7-4
Armrest .................... .1-12
Around view monitor .............4-28
Audible reminders .............. .2-20
Audio operation precautions .........4-46
Audio system ................. .4-46
Audio system, Steering wheel audio
controls .................... .4-89
Auto closure .................. .3-17
Autolight

system ............... .2-36
Automatic Automatic transmission fluid (ATF) . . . .8-13
Climate control .............. 4-40
Driving with automatic transmission . . . 5-13
Automatic door locks ..............3-5
Automatic drive positioner ..........3-25
Automatic seat positioner ...........3-25
Average fuel consumption and speed . . . .2-27
Avoiding collision and rollover .........5-5 B
Back door (See lift gate) ............3-16
Battery ..................... .8-15
Battery Battery saver system ............2-37
Intelligent Key ............... 8-23
Variable voltage control system . ....8-17
Before starting the engine ...........5-12
Belts (See drive belts) .............8-17
Bluetooth hands-free phone system
(models with navigation system) ......4-104
Booster seats ................. .1-35
Brake Anti-lock Braking System (ABS) ......5-76
Brake fluid ................. 8-14
Brake system ................ 5-73
Parking brake operation ..........5-17
Brake warning light ............. .2-13
Break-in schedule .............. .5-68
Brightness control and display ON/OFF
button ...................... .4-7
Brightness control, Instrument panel . . . .2-39
Bulb check/instrument panel . . . . . . . . .2-12
Bulb replacement .............. .8-25
—
—
10/19/09—tbrooks