wheel INFINITI G35 2006 Manual PDF

rear tires and the direction of the wheel
rotation is fixed for each tire.
A pin is on the front brake rotor to pre-
vent the rear wheels from being in-
stalled in place of the front wheels. The
spare tire can be installed in place of
the front and rear wheels. When install-
ing the spare tire in the front wheel, the
hole in the spare tire wheel must be
aligned with the pin on the brake rotor.
WARNINGO Retighten the wheel nuts when the
vehicle has been driven for 600
miles (1,000 km) (also in cases of a
flat tire, etc.).
O For additional information re-
garding tires, refer to ªImportant
Tire Safety Informationº (US) or
ªTire Safety Informationº (Canada)
in the Warranty Information
Booklet. 1. Wear indicator
2. Location mark
Tire wear and damage
WARNINGO Tires should be periodically in-
spected for wear, cracking,
bulging or objects caught in the
tread. If excessive wear, cracks,
bulging or deep cuts are found, the
tire(s) should be replaced. O The original tires have built-in
tread wear indicators. When the
wear indicators are visible, the
tire(s) should be replaced.
O Tires degrade with age and use.
Have tires, including the spare,
over 6 years old checked by a
qualified technician because some
tire damage may not be obvious.
Replace the tires as necessary to
prevent tire failure and possible
personal injury.
O Improper service of the spare tire
may result in serious personal in-
jury. If it is necessary to repair the
spare tire, contact an INFINITI
dealer.
O For additional information re-
garding tires, refer to ªImportant
Tire Safety Informationº (US) or
ªTire Safety Informationº (Canada)
in the Warranty Information
Booklet.
Replacing wheels and tires When replacing a tire, use the same size,
speed rating and load carrying capacity
as originally equipped. See ªSpecifica- MDI0004C
8-46 Maintenance and do-it-yourself
w 06.1.5/V35-D/V5.0
X

tionsº in the ª9. Technical and consumer
informationº section for recommended
types and sizes of tires and wheels.
WARNINGO The use of tires other than those recom-
mended or the mixed use of tires of dif-
ferent brands, construction (bias, bias-
belted or radial), or tread patterns can ad-
versely affect the ride, braking, handling,
ground clearance, body-to-tire clearance,
tire chain clearance, speedometer calibra-
tion, headlight aim and bumper height.
Some of these effects may lead to accidents
and could result in serious personal injury.
O If the wheels are changed for any reason,
always replace with wheels which have
the same off-set dimension. Wheels of a
different off-set could cause premature
tire wear, degrade vehicle handling char-
acteristics and/or interference with the
brake discs. Such interference can lead
to decreased braking efficiency and/or
early brake pad wear.
O When a spare tire is mounted or a wheel
is replaced, tire pressure will not be indi-
cated, the TPMS will not function and the low tire pressure warning light will flash.
Contact your INFINITI dealer as soon as
possible for tire replacement and/or sys-
tem resetting.
O Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
O Do not install a deformed wheel or tire
even if it has been repaired. Such wheels
or tires could have structural damage
and could malfunction without warning.
O The use of retread tires is not recom-
mended.
O For additional information regarding tires,
refer to ªImportant Tire Safety Informationº
(US) or ªTire Safety Informationº (Canada)
in the Warranty Information Booklet.
CAUTION Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Failure to do so may result in a circumference difference between tires on the front and
rear axles which will cause excessive tire
wear and may damage the transmission,
transfer case and differential gears (AWD
models).
Wheel balance Unbalanced wheels may affect vehicle han-
dling and tire life. Even with regular use,
wheels can get out of balance. Therefore,
they should be balanced as required.
Wheel balance service should be per-
formed with the wheels off the vehicle.
Spin balancing the wheels on the vehicle
could lead to transmission damage.
For additional information regarding tires,
refer to ªImportant Tire Safety Informa-
tionº (US) or ªTire Safety Informationº
(Canada) in the INFINITI Warranty Informa-
tion Booklet.
Care of wheels O Wash the wheels when washing the
vehicle to maintain their appearance.
O Clean the inner side of the wheels
when the wheel is changed or the un-
derside of the vehicle is washed.
Maintenance and do-it-yourself
8-47
w 06.1.5/V35-D/V5.0
X

O Do not use abrasive cleaners when
washing the wheels.
O Inspect wheel rims regularly for dents or
corrosion. Such damage may cause loss
of pressure or poor seal at the tire bead.
O INFINITI recommends that the road
wheels be waxed to protect against
road salt in areas where it is used
during winter.
Spare tire (TEMPORARY USE ONLY
spare tire (T-type)) Observe the following precautions if the
T-type spare tire must be used, otherwise
your vehicle could be damaged or in-
volved in an accident.
CAUTIONO The T-type spare tire should be used only
for an emergency. It should be replaced by
a standard tire at the first opportunity.
O Drive carefully while the T-type spare tire
is installed.
Avoid sharp turns and abrupt braking
while driving. O Periodically check the T-type spare tire
inflation pressure, and always keep it at
60 psi (420 kPa, 4.2 bar).
O With the T-type spare tire installed, do
not drive your vehicle at speeds faster
than 50 MPH (80 km/h).
O When driving on roads covered with
snow or ice, the T-type spare tire should
be used on the front wheel and the origi-
nal tire used on the rear wheels (drive
wheels). Use tire chains only on the rear
two original tires (Sedan).
O
Tire tread of the T-type spare tire will wear
at a faster rate than the original tire. Re-
place the T-type spare tire as soon as the
tread wear indicators appear.
O Do not use the T-type spare tire on other
vehicles.
O Do not use more than one T-type spare
tire at the same time.
O Do not tow a trailer while the T-type
spare tire is installed. CAUTION O Do not use tire chains on a T-type spare
tire. Tire chains will not fit properly on
the T-type spare tire and may cause
damage to the vehicle.
O Because the T-type spare tire is smaller
than the original tire, ground clearance
is reduced. To avoid damage to the ve-
hicle do not drive over obstacles. Also do
not drive the vehicle through an auto-
matic car wash since it may get caught.
8-48 Maintenance and do-it-yourself
w 06.1.5/V35-D/V5.0
X

9 Technical and consumer information Capacities and recommended fuel/lubricants ... 9-2
Fuel recommendation .................................. 9-3
Engine oil and oil filter recommendation ..... 9-5
Recommended SAE viscosity number .......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ......................... 9-7
Specifications................................................... 9-8
Engine......................................................... 9-8
Wheels and tires ......................................... 9-9
Dimensions and weights ............................. 9-9
When traveling or registering your vehicle in
another country .............................................. 9-10
Vehicle identification ...................................... 9-10
Vehicle identification number (VIN) plate ... 9-10
Vehicle identification number (Chassis
number) ..................................................... 9-10
Engine serial number ................................. 9-11
F.M.V.S.S./C.M.V.S.S. certification label ..... 9-11
Emission control information label ............. 9-12
Tire and loading information label ............. 9-12
Air conditioner specification label .............. 9-13 Installing front license plate............................ 9-13
Vehicle loading information ............................ 9-14
Terms ........................................................ 9-14
Vehicle load capacity ................................. 9-15
Loading tips ............................................... 9-17
Measurements of weights .......................... 9-17
Towing a trailer ............................................... 9-18
Maximum load limits ................................. 9-18
Towing load/specification chart ................. 9-19
Towing safety ............................................ 9-19
Flat towing ................................................ 9-22
Uniform tire quality grading............................ 9-23
Emission control system warranty .................. 9-24
Reporting safety defects (US only) .................. 9-24
Readiness for inspection/maintenance (I/M)
test (US only).................................................. 9-25
Event data recorders ...................................... 9-26
Owner's Manual/Service Manual order
information ................................................... 9-26
In the event of a collision.......................... 9-27
w 06.1.4/V35-D/V5.0
X

WHEELS AND TIRES
Road wheel Type Position Size Offset in (mm)
Sedan Aluminum Ð 17 x 7JJ 1.77 (45)
Ð 18 x 7-1/2JJ 1.77 (45)
Coupe Aluminum Front 17 x 7-1/2JJ 1.18 (30)
Rear 17 x 8JJ 1.30 (33)
Front 18 x 8JJ 1.18 (30)
Rear 18 x 8JJ 1.18 (30)
Front 19 x 8JJ 1.18 (30)
Rear 19 x 8-1/2JJ 1.30 (33)
Tire Type Position Size Pressure (Cold)
Sedan Conventional Ð P215/55R17 93V 210 kPa (30 psi)
Ð 235/45R18 94W 230 kPa (33 psi)
Spare Ð T145/80D17 420 kPa (60 psi)
P215/55R17 93V*1 210 kPa (30 psi)
Coupe Conventional Front P225/50R17 93V 210 kPa (30 psi)
Rear P235/50R17 95V 210 kPa (30 psi)
Front 225/45R18 91W 240 kPa (35 psi)
Rear 245/45R18 96W 240 kPa (35 psi)
Front 225/40R19 89Y 240 kPa (35 psi)
Rear 245/40R19 94Y 240 kPa (35 psi)
Spare Ð T145/80D17 420 kPa (60 psi)
*1: Option for USA, conventional for Canada (for models with tire size P215/55R17
93V) DIMENSIONS AND WEIGHTS Sedan Coupe
Overall length in (mm) 186.9 (4,747) 182.2 (4,628)
Overall width in (mm) 69.0 (1,753) 71.5 (1,815)
Overall height in (mm) 57.7 (1,467)*1
58.4 (1,484)*2 54.8 (1,393)
55.1 (1,399)*3
Front tread in (mm) 59.1 (1,500)*1
59.3 (1,505)*2 60.4 (1,535)
Rear tread in (mm) 59.3 (1,505) 60.6 (1,540)*4
60.8 (1,545)*5
Wheelbase in (mm) 112.2 (2,850) 112.2 (2,850)
Gross vehicle weight rating lb (kg)
See the F.M.V.S.S./C.M.V.S.S.
certification label on the driver's
side lock pillar.Gross axle weight rating
Front lb (kg)
Rear lb (kg)
*1: For 2WD models
*2: For AWD models
*3: For 18 in and 19 in road wheel models
*4: For models with road wheel size Ð 17 x 8JJ and 19 x 8-1/2JJ [offset 1.30 in (33
mm)]
*5: For models with road wheel size Ð 18 x 8JJ [offset 1.18 in (30 mm)]
Technical and consumer information
9-9
w 06.1.4/V35-D/V5.0
X

the vehicle. That weight may not
safely exceed the available cargo
and luggage load capacity calcu-
lated in Step 4.
6. If your vehicle will be towing a
trailer, load from your trailer will be
transferred to your vehicle. Consult
this manual to determine how this
reduces the available cargo and lug-
gage load capacity of your vehicle.
Before driving a loaded vehicle, confirm
that you do not exceed the Gross Ve-
hicle Weight Rating (GVWR) or the
Gross Axle Weight Rating (GAWR) for
your vehicle. See ``Measurement of
Weights'' later in this section.
Also check tires for proper inflation
pressures. See the Tire and Loading In-
formation label.
LOADING TIPS
O The GVW must not exceed GVWR or
GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification
label.
O Do not load the front and rear axle
to the GAWR. Doing so will exceed
the GVWR.
WARNINGO Properly secure all cargo with
ropes or straps to help prevent it
from sliding or shifting. Do not
place cargo higher than the seat-
backs. In a sudden stop or colli-
sion, unsecured cargo could cause
personal injury.
O Do not load your vehicle any
heavier than the GVWR or the
maximum front and rear GAWRs. If
you do, parts of your vehicle can
break, tire damage could occur, or
it can change the way your vehicle
handles. This could result in loss
of control and cause personal
injury. O Overloading not only can shorten
the life of your vehicle and the tire,
but can also cause unsafe vehicle
handling and longer braking dis-
tances. This may cause a prema-
ture tire failure which could result
in a serious accident and personal
injury. Failures caused by over-
loading are not covered by the ve-
hicle's warranty.
MEASUREMENT OF WEIGHTS
Secure loose items to prevent weight
shifts that could affect the balance of
your vehicle. When the vehicle is
loaded, drive to a scale and weigh the
front and the rear wheels separately to
determine axle loads. Individual axle
loads should not exceed either of the
gross axle weight ratings (GAWR). The
total of the axle loads should not ex-
ceed the gross vehicle weight rating
(GVWR). These ratings are given on the
vehicle certification label. If weight rat-
ings are exceeded, move or remove
items to bring all weights below the rat-
ings. Technical and consumer information
9-17
w 06.1.4/V35-D/V5.0
X

WARNINGNever connect a trailer brake system directly
to the vehicle brake system.
Pre-towing tips O Be certain your vehicle maintains a
level position when a loaded and/or
unloaded trailer is hitched. Do not
drive the vehicle if it has an abnormal
nose-up or nose-down condition;
check for improper tongue load, over-
load, worn suspension or other pos-
sible causes of either condition.
O Always secure items in the trailer to
prevent load shifts while driving.
O Load the trailer so approximately 60%
of the trailer load is in the front half
and 40% is in the back half.
O Check your hitch, trailer tire pressure,
vehicle tire pressure, trailer light op-
eration, and trailer wheel lug nuts
every time you attach a trailer to the
vehicle.
O Be certain your rear view mirrors con-
form to all federal, state or local regula- tions. If not, install any mirrors required
for towing before driving the vehicle.
Trailer towing tips In order to gain skill and an under-
standing of the vehicle's behavior, you
should practice turning, stopping and
backing up in an area which is free from
traffic. Steering stability, and braking per-
formance will be somewhat different than
under normal driving conditions.
O Always secure items in the trailer to
prevent load shift while driving.
O Avoid abrupt starts, acceleration or
stops.
O Avoid sharp turns or lane changes.
O Always drive your vehicle at a mod-
erate speed. Some states or provinces
have specific speed limits for vehicles
that are towing trailers. Obey the local
speed limits.
O When backing up, hold the bottom of
the steering wheel with one hand.
Move your hand in the direction in
which you want the trailer to go. Make
small corrections and back up slowly.
If possible, have someone guide you
when you are backing up. O Always block the wheels on both vehicle
and trailer when parking. Parking on a
slope is not recommended; however, if
you must do so, and if your vehicle is
equipped with automatic transmission,
first apply the parking brake and block
the wheels, and then move the transmis-
sion selector lever into the P (Park) posi-
tion. If you move the selector lever to
the P (Park) position before applying the
parking brake and blocking the wheels,
transmission damage could occur.
O When going down a hill, shift into a
lower gear and use the engine braking
effect. When going up a long grade,
downshift the transmission to a lower
gear and reduce speed to reduce
chances of engine overloading and/or
overheating.
However, for long steep grades, do
not stay in 1st or 2nd gear when
driving above 35 MPH (56 km/h).
O If the engine coolant rises to an ex-
tremely high temperature when the air
conditioning system is on, turn off the
air conditioner. Coolant heat can be
additionally vented by opening the
windows, switching the fan control to
high and setting the temperature con-
trol to the HOT position.
Technical and consumer information
9-21
w 06.1.4/V35-D/V5.0
X

O Trailer towing requires more fuel than
normal circumstances.
O Avoid towing a trailer for the first 500
miles (800 km).
O Have your vehicle serviced more often
than at intervals specified in the rec-
ommended maintenance schedule in
the INFINITI Service and Maintenance
Guide.
O When making a turn, your trailer
wheels will be closer to the inside of
the turn than your vehicle wheels. To
compensate for this, make a larger
than normal turning radius during the
turn.
O Crosswinds and rough roads will ad-
versely affect vehicle/trailer handling,
possibly causing vehicle sway. When
being passed by larger vehicles, be
prepared for possible changes in
crosswinds that could affect vehicle
handling. If swaying does occur, firmly
grip the steering wheel, steer straight
ahead, and immediately (but gradu-
ally) reduce vehicle speed. This combi-
nation will help stabilize the vehicle.
Never increase speed. O Be careful when passing other vehicles.
Passing while towing a trailer requires
considerably more distance than normal
passing. Remember the length of the
trailer must also pass the other vehicle
before you can safely change lanes.
O To maintain engine braking efficiency
and electrical charging performance,
do not use sixth gear (manual trans-
mission) or fifth position (automatic
transmission).
O Avoid holding the brake pedal down
too long or too frequently. This could
cause the brakes to overheat, re-
sulting in reduced braking efficiency.
O Increase your following distance to al-
low for greater stopping distances
while towing a trailer. Anticipate stops
and brake gradually.
O Do not use cruise control while towing
a trailer.
O Check your hitch, trailer wiring har-
ness connections, and trailer wheel
lug nuts after 50 miles (80 km) of
travel and at every break.
O When stopped in traffic for long pe-
riods of time in hot weather, put the
vehicle in the P (Park) position. When towing a trailer, transmission
oil/fluid should be changed more fre-
quently.
For additional information, see the ª8.
Maintenance and do-it-yourselfº section
earlier in this manual.
FLAT TOWING Towing your vehicle with all four wheels
on the ground is sometimes called flat
towing. This method is sometimes used
when towing a vehicle behind a recre-
ational vehicle, such as a motor home.
CAUTION O Failure to follow these guidelines can re-
sult in severe transmission damage.
O Whenever flat towing your vehicle, al-
ways tow forward, never backward.
O DO NOT tow any automatic transmission
vehicle with all four wheels on the
ground (flat towing). Doing so WILL
DAMAGE internal transmission parts due
to lack of transmission lubrication.
9-22 Technical and consumer information
w 06.1.4/V35-D/V5.0
X

O For emergency towing procedures refer
to ªTowing recommended by INFINITIº in
the ª6. In case of emergencyº section of
this manual.
Automatic transmission To tow a vehicle equipped with an auto-
matic transmission, an appropriate ve-
hicle dolly MUST be placed under the
towed vehicle's drive wheels. Always
follow the dolly manufacturer's recom-
mendations when using their product.
Manual transmission O Always tow with the manual transmis-
sion in Neutral.
O After towing 500 miles, start and idle
the engine with the transmission in
Neutral for two minutes. Failure to idle
the engine after every 500 miles of
towing may cause damage to the
transmission's internal parts. DOT (Department Of Transportation) Qual-
ity Grades: All passenger car tires must
conform to federal safety requirements in
addition to these grades.
Quality grades can be found where appli-
cable on the tire sidewall between tread
shoulder and maximum section width. For
example:
Treadwear 200 Traction AA Temperature A
Treadwear The treadwear grade is a comparative rat-
ing based on the wear rate of the tire
when tested under controlled conditions
on a specified government test course.
For example, a tire graded 150 would wear
one and one-half (1 1/2) times as well on
the government course as a tire graded
100. The relative performance of tires de-
pends upon the actual conditions of their
use, however, and may depart signifi-
cantly from the norm due to variations in
driving habits, service practices and dif-
ferences in road characteristics and cli-
mate.
Traction AA, A, B and C The traction grades, from highest to
lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet
pavement as measured under controlled
conditions on specified government test
surfaces of asphalt and concrete. A tire
marked C may have poor traction perfor-
mance.
WARNING The traction grade assigned to this tire is
based on straight-ahead braking traction
tests, and does not include acceleration, cor-
nering, hydroplaning, or peak traction char-
acteristics.
Temperature A, B and C The temperature grades A (the highest),
B, and C, representing the tire's resis-
tance to the generation of heat and its
ability to dissipate heat when tested
under controlled conditions on a specified
indoor laboratory test wheel. Sustained
high temperature can cause the material
of the tire to degenerate and reduce tire
life, and excessive temperature can lead
to sudden tire failure. The grade C corre-
sponds to a level of performance which
all passenger car tires must meet under
the Federal Motor Safety Standard No.UNIFORM TIRE QUALITY GRADING
Technical and consumer information
9-23
w 06.1.5/V35-D/V5.0
X

109. Grades B and A represent higher lev-
els of performance on the laboratory test
wheel than the minimum required by law.
WARNINGThe temperature grade for this tire is estab-
lished for a tire that is properly inflated and
not overloaded. Excessive speed, under-
inflation, or excessive loading, either sepa-
rately or in combination, can cause heat
build-up and possible tire failure. Your INFINITI is covered by the following
emission warranties.
For US:
O Emission Defects Warranty
O Emissions Performance Warranty
(See Warranty Information Booklet for
details.)
For Canada:
Emission Control System Warranty
Details of these warranties may be found
with other vehicle warranties in your War-
ranty Information Booklet (Warranty and
Roadside Assistance Information (Canada
only)) that comes with your INFINITI. If you
did not receive a Warranty Information
Booklet (Warranty and Roadside Assis-
tance Information (Canada only)), or it has
become lost, you may obtain a replace-
ment by writing to:
O INFINITI Division
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 47038, Gardena, CA 90247-
6838
O Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario, L4W 4Z5 If you believe that your vehicle has a
defect which could cause a crash or
could cause injury or death, you should
immediately inform the National
Highway Traffic Safety Administration
(NHTSA) in addition to notifying
INFINITI.
If
NHTSA receives similar complaints, it
may open an investigation, and if it
finds that a safety defect exists in a
group of vehicles, it may order a recall
and remedy campaign. However,
NHTSA cannot become involved in indi-
vidual problems between you, your
dealer, or INFINITI.
To contact
NHTSA , you may call the Ve-
hicle Safety Hotline toll-free at 1-888-
327-4236 (TTY: 1-800-424-9153): go to
http://www.safercar.gov; or write to:
Administrator,
NHTSA , 400 Seventh
Street, SW., Washington, DC 20590.
You can also obtain other information
about motor vehicle safety from
http://www.safercar.gov.
You may notify INFINITI by contacting
our Consumer Affairs Department, toll-
free, at 1-800-662-6200.EMISSION CONTROL SYSTEM WARRANTY REPORTING SAFETY DEFECTS (US only)
9-24 Technical and consumer information
w 06.1.5/V35-D/V5.0
X