brake sensor INFINITI M35 2006 Factory Owners Manual

EC-18
[VQ35DE]
INDEX FOR DTC
Revision: 2006 January2006 M35/M45
P0456 0456 EVAP VERY SML LEAKEC-466
P0460 0460 FUEL LEV SEN SLOSHEC-475
P0461 0461 FUEL LEVEL SENSOREC-477
P0462 0462 FUEL LEVL SEN/CIRCEC-479
P0463 0463 FUEL LEVL SEN/CIRCEC-479
P0500 0500
VEH SPEED SEN/CIRC*5EC-481
P0506 0506 ISC SYSTEMEC-483
P0507 0507 ISC SYSTEMEC-485
P0550 0550 PW ST P SEN/CIRCEC-487
P0603 0603 ECM BACK UP/CIRCUITEC-492
P0605 0605 ECMEC-496
P0643 0643 SENSOR POWER/CIRCEC-499
P0700 0700 TCMAT- 11 2
P0705 0705 PNP SW/CIRCAT- 11 3
P0710 0710 ATF TEMP SEN/CIRCAT-135
P0717 0717 TURBINE SENSORAT- 11 7
P0720 0720
VEH SPD SEN/CIR AT*5AT- 11 9
P0725 0725 ENGINE SPEED SIGAT-124
P0740 0740 TCC SOLENOID/CIRCAT-126
P0744 0744 A/T TCC S/V FNCTNAT-128
P0745 0745 L/PRESS SOL/CIRCAT-130
P0850 0850 P-N POS SW/CIRCUITEC-504
P1148 1148 CLOSED LOOP-B1EC-509
P1168 1168 CLOSED LOOP-B2EC-509
P1211 1211 TCS C/U FUNCTNEC-510
P1212 1212 TCS/CIRCEC-511
P1217 1217 ENG OVER TEMPEC-512
P1220 1220 FPCM/CIRCUITEC-525
P1225 1225 CTP LEARNINGEC-533
P1226 1226 CTP LEARNINGEC-535
P1550 1550 BAT CURRENT SENSOREC-537
P1551 1551 BAT CURRENT SENSOREC-543
P1552 1552 BAT CURRENT SENSOREC-543
P1553 1553 BAT CURRENT SENSOREC-549
P1554 1554 BAT CURRENT SENSOREC-555
P1564 1564 ASCD SWEC-561 (Models with ICC)
EC-568
(Models with ASCD)
P1568 1568
ICC COMMAND VALUE*
6EC-575
P1572 1572 ASCD BRAKE SWEC-576 (Models with ICC)
EC-585
(Models with ASCD)
P1574 1574 ASCD VHL SPD SENEC-593
(Models with ICC)
EC-595
(Models with ASCD)
P1610 - P1615 1610 - 1615 NATS MALFUNCTIONEC-53
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3

INDEX FOR DTC
EC-19
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 January2006 M35/M45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: Models with ICC.P1705 1705 TP SEN/CIRC A/TAT-132
P1715 1715 IN PULY SPEEDEC-597
P1730 1730 A/T INTERLOCKAT-142
P1752 1752 I/C SOLENOID/CIRCAT-147
P1754 1754 I/C SOLENOID FNCTNAT-149
P1757 1757 FR/B SOLENOID/CIRCAT-151
P1759 1759 FR/B SOLENOID FNCTAT-153
P1762 1762 D/C SOLENOID/CIRCAT-155
P1764 1764 D/C SOLENOID FNCTNAT-157
P1767 1767 HLR/C SOL/CIRCAT-159
P1769 1769 HLR/C SOL FNCTNAT-161
P1772 1772 LC/B SOLENOID/CIRCAT-163
P1774 1774 LC/B SOLENOID FNCTAT-165
P1805 1805 BRAKE SW/CIRCUITEC-598
P2100 2100 ETC MOT PWREC-607
P2101 2101 ETC FUNCTION/CIRCEC-613
P2103 2103 ETC MOT PWREC-607
P 2 11 8 2 11 8 E T C M O TEC-619
P 2 11 9 2 11 9 E T C A C T REC-624
P2122 2122 APP SEN 1/CIRCEC-626
P2123 2123 APP SEN 1/CIRCEC-626
P2127 2127 APP SEN 2/CIRCEC-633
P2128 2128 APP SEN 2/CIRCEC-633
P2135 2135 TP SENSOREC-640
P2138 2138 APP SENSOREC-647
P2A00 2A00 A/F SENSOR1 (B1)EC-655
P2A03 2A03 A/F SENSOR1 (B2)EC-655
DTC*1
Items
(CONSULT-II screen terms)Reference page
CONSULT-II
GST*
2ECM*3

EC-20
[VQ35DE]
INDEX FOR DTC
Revision: 2006 January2006 M35/M45
Alphabetical IndexNBS004RV
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to EC-173, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
If DTC U1010 is displayed with other DTC, first perform the trouble diagnosis for DTC U1010. Refer
to EC-176, "
DTC U1010 CAN COMMUNICATION" .
Items
(CONSULT-II screen terms)DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SEN1 HTR (B1) P0031 0031EC-182
A/F SEN1 HTR (B1) P0032 0032EC-182
A/F SEN1 HTR (B2) P0051 0051EC-182
A/F SEN1 HTR (B2) P0052 0052EC-182
A/F SENSOR1 (B1) P0130 0130EC-246
A/F SENSOR1 (B1) P0131 0131EC-256
A/F SENSOR1 (B1) P0132 0132EC-265
A/F SENSOR1 (B1) P0133 0133EC-274
A/F SENSOR1 (B1) P2A00 2A00EC-655
A/F SENSOR1 (B2) P0150 0150EC-246
A/F SENSOR1 (B2) P0151 0151EC-256
A/F SENSOR1 (B2) P0152 0152EC-265
A/F SENSOR1 (B2) P0153 0153EC-274
A/F SENSOR1 (B2) P2A03 2A03EC-655
A/T INTERLOCK P1730 1730AT-142
A/T TCC S/V FNCTN P0744 0744AT-128
APP SENSOR P2138 2138EC-647
APP SEN 1/CIRC P2122 2122EC-626
APP SEN 1/CIRC P2123 2123EC-626
APP SEN 2/CIRC P2127 2127EC-633
APP SEN 2/CIRC P2128 2128EC-633
ASCD BRAKE SW P1572 1572EC-576 (Models with ICC)
EC-585
(Models with ASCD)
ASCD SW P1564 1564EC-561
(Models with ICC)
EC-568
(Models with ASCD)
ASCD VHL SPD SEN P1574 1574EC-593
(Models with ICC)
EC-595
(Models with ASCD)
ATF TEMP SEN/CIRC P0710 0710AT-135
BAT CURRENT SENSOR P1550 1550EC-537
BAT CURRENT SENSOR P1551 1551EC-543
BAT CURRENT SENSOR P1552 1552EC-543
BAT CURRENT SENSOR P1553 1553EC-549
BAT CURRENT SENSOR P1554 1554EC-555
BRAKE SW/CIRCUIT P1805 1805EC-598
CAN COMM CIRCUIT U1000
1000*4EC-173
CAN COMM CIRCUIT U1001
1001*4EC-173
CKP SEN/CIRCUIT P0335 0335EC-376
CLOSED LOOP-B1 P1148 1148EC-509

EC-36
[VQ35DE]
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
Revision: 2006 January2006 M35/M45
AUTOMATIC SPEED CONTROL DEVICE (ASCD)PFP:18930
System DescriptionNBS004S8
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM through CAN communication line
BASIC ASCD SYSTEM
Refer to Owner's Manual for ASCD operating instructions.
Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed
without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/
h (25 MPH) and 144 km/h (89 MPH).
ECM controls throttle angle of electric throttle control actuator to regulate engine speed.
Operation status of ASCD is indicated by CRUISE lamp and SET lamp in combination meter. If any malfunc-
tion occurs in ASCD system, it automatically deactivates control.
NOTE:
Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
SET OPERATION
Press MAIN switch. (The CRUISE lamp in combination meter illuminates.)
When vehicle speed reaches a desired speed between approximately 40 km/h (25 MPH) and 144 km/h (89
MPH), press SET/COAST switch. (Then SET lamp in combination meter illuminates.)
ACCEL OPERATION
If the RESUME/ACCELERATE switch is pressed during cruise control driving, increase the vehicle speed until
the switch is released or vehicle speed reaches maximum speed controlled by the system.
And then ASCD will keep the new set speed.
CANCEL OPERATION
When any of following conditions exist, cruise operation will be canceled.
CANCEL switch is pressed
More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)
Brake pedal is depressed
Selector lever is changed to N, P, R position
Vehicle speed decreased to 13 km/h (8 MPH) lower than the set speed
TCS system is operated
When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform
the driver by blinking indicator lamp.
Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may
blink slowly.
When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will
stop blinking and the cruise operation will be able to work by pressing SET/COAST switch or RESUME/
ACCELERATE switch.
Malfunction for some self-diagnoses regarding ASCD control: SET lamp will blink quickly.
If MAIN switch is turned to OFF during ASCD is activated, all of ASCD operations will be canceled and vehicle
speed memory will be erased.
Sensor Input signal to ECM ECM function Actuator
ASCD brake switch Brake pedal operation
ASCD vehicle speed controlElectric throttle control
actuator Stop lamp switch Brake pedal operation
ASCD steering switch ASCD steering switch operation
Park/Neutral position (PNP)
switchGear position
Wheel sensor* Vehicle speed
TCM* Powertrain revolution

ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-57
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 January2006 M35/M45EVAP GROSS LEAK P0455 0455 — — 2EC-458
EVAP VERY SML LEAK P0456 0456*72EC-466
FUEL LEV SEN SLOSH P0460 0460 — — 2EC-475
FUEL LEVEL SENSOR P0461 0461 — — 2EC-477
FUEL LEVL SEN/CIRC P0462 0462 — — 2EC-479
FUEL LEVL SEN/CIRC P0463 0463 — — 2EC-479
VEH SPEED SEN/CIRC*5P0500 0500 — — 2EC-481
ISC SYSTEM P0506 0506 — — 2EC-483
ISC SYSTEM P0507 0507 — — 2EC-485
PW ST P SEN/CIRC P0550 0550 — — 2 —EC-487
ECM BACK UP/CIRCUIT P0603 0603 — — 2EC-492
ECM P0605 0605 — —1 or
2 or
—EC-496
SENSOR POWER/CIRC P0643 0643 — — 1EC-499
TCM P0700 0700 — — 1AT- 11 2
PNP SW/CIRC P0705 0705 — — 2AT- 11 3
ATF TEMP SEN/CIRC P0710 0710 — — 2AT- 1 3 5
TURBINE SENSOR P0717 0717 — — 2AT- 11 7
VEH SPD SEN/CIR AT*5P0720 0720 — — 2AT- 11 9
ENGINE SPEED SIG P0725 0725 — — 2AT- 1 2 4
TCC SOLENOID/CIRC P0740 0740 — — 2AT- 1 2 6
A/T TCC S/V FNCTN P0744 0744 — — 2AT- 1 2 8
L/PRESS SOL/CIRC P0745 0745 — — 2AT- 1 3 0
P-N POS SW/CIRCUIT P0850 0850 — — 2EC-504
CLOSED LOOP-B1 P1148 1148 — — 1EC-509
CLOSED LOOP-B2 P1168 1168 — — 1EC-509
TCS C/U FUNCTN P1211 1211 — — 2 —EC-510
TCS/CIRC P1212 1212 — — 2 —EC-511
ENG OVER TEMP P1217 1217 — — 1EC-512
FPCM/CIRCUIT P1220 1220 — — 2EC-525
CTP LEARNING P1225 1225 — — 2 —EC-533
CTP LEARNING P1226 1226 — — 2 —EC-535
BAT CURRENT SENSOR P1550 1550 — — 2 —EC-537
BAT CURRENT SENSOR P1551 1551 — — 2 —EC-543
BAT CURRENT SENSOR P1552 1552 — — 2 —EC-543
BAT CURRENT SENSOR P1553 1553 — — 2 —EC-549
BAT CURRENT SENSOR P1554 1554 — — 2 —EC-555
ASCD SW P1564 1564 — — 1 — EC-561 (Models with ICC)
EC-568
(Models with ASCD)
ICC COMMAND VALUE*
6P1568 1568 — — 1 —EC-575
ASCD BRAKE SW P1572 1572 — — 1 — EC-576 (Models with ICC)
EC-585
(Models with ASCD) Items
(CONSULT-II screen terms)DTC*
1
SRT codeTest value/
Test limit
(GST only)Trip MIL Reference page
CONSULT-II
GST*
2ECM*3

EC-58
[VQ35DE]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
Revision: 2006 January2006 M35/M45
*1: 1st trip DTC No. is the same as DTC No.
*2: This number is prescribed by SAE J2012.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: The troubleshooting for this DTC needs CONSULT-II.
*5: When the fail-safe operations for both self-diagnoses occur at the same time, the MIL illuminates.
*6: Models with ICC.
*7: SRT code will not be set if the self-diagnostic result is NG.
*8: When the ECM is in the mode of displaying SRT status, MIL may flash. For the details, refer to EC-62, "
How to Display SRT Status" .
DTC AND 1ST TRIP DTC
The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not reoccur, the 1st trip
DTC will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is stored in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are stored in the ECM memory and the MIL lights up. In other words,
ASCD VHL SPD SEN P1574 1574 — — 1 — EC-593 (Models with ICC)
EC-595
(Models with ASCD)
NATS MALFUNCTIONP1610 -
P16151610 - 1615 — — 2 —EC-53
TP SEN/CIRC A/T P1705 1705 — — 1AT-132
IN PULY SPEED P1715 1715 — — 2 —EC-597
A/T INTERLOCK P1730 1730 — — 1AT-142
I/C SOLENOID/CIRC P1752 1752 — — 1AT-147
I/C SOLENOID FNCTN P1754 1754 — — 1AT-149
FR/B SOLENOID/CIRC P1757 1757 — — 1AT-151
FR/B SOLENOID FNCT P1759 1759 — — 1AT-153
D/C SOLENOID/CIRC P1762 1762 — — 1AT-155
D/C SOLENOID FNCTN P1764 1764 — — 1AT-157
HLR/C SOL/CIRC P1767 1767 — — 1AT-159
HLR/C SOL FNCTN P1769 1769 — — 1AT-161
LC/B SOLENOID/CIRC P1772 1772 — — 1AT-163
LC/B SOLENOID FNCT P1774 1774 — — 1AT-165
BRAKE SW/CIRCUIT P1805 1805 — — 2 —EC-598
ETC MOT PWR P2100 2100 — — 1EC-607
ETC FUNCTION/CIRC P2101 2101 — — 1EC-613
ETC MOT PWR P2103 2103 — — 1EC-607
ETC MOT P2118 2118 — — 1EC-619
ETC ACTR P2119 2119 — — 1EC-624
APP SEN 1/CIRC P2122 2122 — — 1EC-626
APP SEN 1/CIRC P2123 2123 — — 1EC-626
APP SEN 2/CIRC P2127 2127 — — 1EC-633
APP SEN 2/CIRC P2128 2128 — — 1EC-633
TP SENSOR P2135 2135 — — 1EC-640
APP SENSOR P2138 2138 — — 1EC-647
A/F SENSOR1 (B1) P2A00 2A00 —2EC-655
A/F SENSOR1 (B2) P2A03 2A03 —2EC-655
Items
(CONSULT-II screen terms)DTC*
1
SRT codeTest value/
Te s t l i m i t
(GST only)Trip MIL Reference page
CONSULT-II
GST*
2ECM*3

BASIC SERVICE PROCEDURE
EC-91
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 January2006 M35/M45
19. CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
With CONSULT-II
1. Turn ignition switch OFF and wait at a least 10 seconds.
2. Start engine and warm it up to normal operating temperature.
3. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in D position.
NOTE:
Keep the accelerator pedal as steady as possible during the cruising.
4. Release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (30 MPH).
NOTE:
Never apply brake during releasing the accelerator pedal.
5. Repeat steps 3 to 4 for five times.
6. Stop the vehicle and connect CONSULT-II to the vehicle.
7. Make sure that no (1st trip) DTC is displayed in “SELF-DIAG RESULTS” mode.
OK or NG
OK >>INSPECTION END
NG >> GO TO 21.
20. CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
With GST
1. Turn ignition switch OFF and wait at a least 10 seconds.
2. Start engine and warm it up to normal operating temperature.
3. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in D position.
NOTE:
Keep the accelerator pedal as steady as possible during the cruising.
4. Release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (30 MPH).
NOTE:
Never apply brake during releasing the accelerator pedal.
5. Repeat steps 3 to 4 for five times.
6. Stop the vehicle and connect GST to the vehicle.
7. Make sure that no (1st trip) DTC is displayed.
OK or NG
OK >>INSPECTION END
NG >> GO TO 21.

EC-94
[VQ35DE]
BASIC SERVICE PROCEDURE
Revision: 2006 January2006 M35/M45
29. CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
With CONSULT-II
1. Turn ignition switch OFF and wait at a least 10 seconds.
2. Start engine and warm it up to normal operating temperature.
3. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in D position.
NOTE:
Keep the accelerator pedal as steady as possible during the cruising.
4. Release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (30 MPH).
NOTE:
Never apply brake during releasing the accelerator pedal.
5. Repeat steps 3 to 4 for five times.
6. Stop the vehicle and connect CONSULT-II to the vehicle.
7. Make sure that no (1st trip) DTC is displayed in “SELF-DIAG RESULTS” mode.
OK or NG
OK >> GO TO 4.
NG >> GO TO 31.
30. CHECK AIR FUEL RATIO (A/F) SENSOR 1 FUNCTION
With GST
1. Turn ignition switch OFF and wait at a least 10 seconds.
2. Start engine and warm it up to normal operating temperature.
3. Drive the vehicle at a speed of 80 km/h (50 MPH) for a few minutes in D position.
NOTE:
Keep the accelerator pedal as steady as possible during the cruising.
4. Release the accelerator pedal fully until the vehicle speed decreases to 50 km/h (30 MPH).
NOTE:
Never apply brake during releasing the accelerator pedal.
5. Repeat steps 3 to 4 for five times.
6. Stop the vehicle and connect GST to the vehicle.
7. Make sure that no (1st trip) DTC is displayed.
OK or NG
OK >> GO TO 4.
NG >> GO TO 31.
31. DETECT MALFUNCTIONING PART
Check the following.
Check fuel pressure regulator, and repair or replace if necessary. Refer to EC-98, "FUEL PRESSURE
CHECK" .
Check mass air flow sensor and its circuit, and repair or replace if necessary. Refer to EC-205, "DTC
P0101 MAF SENSOR" and EC-214, "DTC P0102, P0103 MAF SENSOR" .
Check fuel injector and its circuit, and repair or replace if necessary. Refer to EC-679, "FUEL INJECTOR"
.
Check engine coolant temperature sensor and its circuit, and repair or replace if necessary. Refer to EC-
226, "DTC P0117, P0118 ECT SENSOR" and EC-238, "DTC P0125 ECT SENSOR" .
OK or NG
OK >> GO TO 33.
NG >> 1. Repair or replace.
2. GO TO 32.

TROUBLE DIAGNOSIS
EC-107
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 January2006 M35/M45
*: With ICC models2
P0031 P0032 P0051 P0052 Air fuel ratio (A/F) sensor 1 heater
P0037 P0038 P0057 P0058 Heated oxygen sensor 2 heater
P0075 P0081 Intake valve timing control solenoid valve
P0130 P0131 P0132 P0133 P0150 P0151 P0152 P0153 P2A00 P2A03 Air fuel ratio (A/F) sensor 1
P0137 P0138 P0139 P0157 P0158 P0159 Heated oxygen sensor 2
P0441 EVAP control system purge flow monitoring
P0443 P0444 P0445 EVAP canister purge volume control solenoid valve
P0447 P0448 EVAP canister vent control valve
P0451 P0452 P0453 EVAP control system pressure sensor
P0550 Power steering pressure sensor
P0603 ECM power supply
P0710 P0717 P0720 P0725 P0740 P0744 P0745 P1705 P1715 P1730 P1752 P1754 P1757 P1759 P1762 P1764
P1767 P1769 P1772 P1774 A/T related sensors, solenoid valves and switches
P1217 Engine over temperature (OVERHEAT)
P1220 Fuel pump control module
P1805 Brake switch
P2100 P2103 Throttle control motor relay
P2101 Electric throttle control function
P2118 Throttle control motor
3
P0011 P0021 Intake valve timing control
P0171 P0172 P0174 P0175 Fuel injection system function
P0300 - P0306 Misfire
P0420 P0430 Three way catalyst function
P0442 P0456 EVAP control system (SMALL LEAK, VERY SMALL LEAK)
P0455 EVAP control system (GROSS LEAK)
P0506 P0507 Idle speed control system
P1148 P1168 Closed loop control
P1211 TCS control unit
P1212 TCS communication line
P1564 ICC steering switch / ASCD steering switch
P1568 ICC command value*
P1572 ICC brake switch / ASCD brake switch
P1574 ICC vehicle speed sensor / ASCD vehicle speed sensor
P2119 Electric throttle control actuator Priority Detected items (DTC)

TROUBLE DIAGNOSIS
EC-113
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: 2006 January2006 M35/M45
Engine Control Component Parts LocationNBS004T2
1. IPDM E/R 2. ICC brake hold relay
(ICC models only)3. Battery current sensor
4. Cooling fan relay 5. Power steering pressure sensor 6. Refrigerant pressure sensor
7. Intake valve timing control solenoid
valve (bank 1)8. Cooling fan motor-2 9. Cooling fan control module
10. Intake valve timing control solenoid
valve (bank 2)11. Cooling fan motor-1 12. Mass air flow sensor
(with intake air temperature sensor)
13. Ignition coil (with power transistor)
and spark plug (bank 2)14. Camshaft position sensor (PHASE)
(Bank 2)15. Electric throttle control actuator
16. Fuel injector (bank 2) 17. Knock sensor 18. Fuel injector (bank 1)
19. EVAP canister purge volume con-
trol solenoid valve20. Camshaft position sensor (PHASE)
(Bank 1)21. Engine coolant temperature sensor
22. Ignition coil (with power transistor)
and spark plug (bank 1)23. EVAP service port
PBIB2781E