rear entertainment INFINITI M35 2006 Factory User Guide

AV-78
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
*1: 2WD models without navigation system and RAS
*2: Except *1
*3: With rear view monitor
*4: With navigation system
Front Display UnitNKS0048Q
67*3
(V)GroundCamera-connection rec-
ognition signalInput ONConnected to rear view
camera control unit connec-
tor.Approx. 0 V
Not connected to rear view
camera control unit connec-
tor.Approx. 5 V
69
(W)–Communication signal
(H)Input/
Output–– –
70
(R)–Communication signal
(L)Input/
Output–– –
71
(LG)–CAN-HInput/
Output–– –
72
(P)–CAN-LInput/
Output–– –
107
*4Ground GPS signal Input ON Connector is not connected. Approx. 5 V Te r m i n a l
(Wire color)
ItemSignal
Input/
outputCondition
Reference value
+–Ignition
switchOperation
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
1
(L/G)8
(W/L)RGB Signal (R: red) Input ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
2
(G)Ground RGB area (YS) signal Input ONWhen inputting RGB image. Approx.5 V
Set the selector lever in R
position, and then display
the rear view image.
3
(O/L)8
(W/L)RGB signal (G: green) Input ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
SKIB2238J
PKIB4948J
SKIB2236J

TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
AV-79
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
4
(W)GroundHorizontal synchronizing
(HP) signalOutput ON –
5
(L/Y)8
(W/L)RGB signal (B: blue) Input ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
6
(R)GroundVertical synchronizing
(VP) signalInput ON –
7
(B)GroundRGB synchronizing sig-
nalInput ON –
8
(W/L)Ground RGB ground – ON – Approx. 0 V
10 – Shield – – – –
11
*1
(Y)Ground Camera image signal Input ONSet selector lever in R posi-
tion, and then display the
rear view image.
12
*1– Shield – – – –
14
*2– Shield – – – –
15
*2
(L)Ground Composite image signal Output ON DVD image Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB3601E
SKIB2237J
SKIB3598E
SKIB3603E
SKIB2251J
SKIB2251J

AV-80
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
*1: With rear view monitor
*2: With BOSE surround 5.1ch system
DVD PlayerNKS0048R
17
(W/L)GroundCommunication signal
(DISP-CONT)Output ONWhen adjusting display
brightness.
18 – Shield – – – –
19
(O/L)GroundCommunication signal
(CONT-DISP)Output ONWhen adjusting display
brightness.
20
(V)Ground ACC power supply Input ACC – Battery voltage
21
(L)Ground BAT power supply Input OFF – Battery voltage
23
(B)Ground Ground – ON – Approx. 0 V Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
PKIB5039J
PKIB5039J
Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
1
(Y)Ground Battery power supply Input OFF – Battery voltage
2
(V)Ground ACC power supply Input ACC – Battery voltage
4
(W)Ground AUX image signal Input ON –
5 – Shield – – – –
7
(W)6
(B)AUX sound signal RH Input ON AUX sound input
14 – Shield – – – –
SKIB2251J
SKIB3609E

AV-82
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
CAUTION:
When the stereo sound is played, only front RH and LH are output. When the monaural sound is played, only center is output.
All surround sounds are input only when the 5.1 channel surround sound is played. 34
(B/Y)42
(LG)DVD sound signal front
RHOutput ON
When playing DVD
CAUTION
35
(L/R)43
(L/G)DVD sound signal front
LHOutput ON
When playing DVDCAUTION
36
(R/B)44
(R)DVD sound signal center Output ON
When playing DVDCAUTION
37
(Y/B)45
(Y)DVD sound signal woofer Output ON
When playing DVDCAUTION
38
(G/R)– Shield – – – –
39
(Y/L)47
(W/L)DVD sound signal rear
RHOutput ON
When playing DVD
CAUTION
40
(O/L)48
(O)DVD sound signal rear
LHOutput ON
When playing DVDCAUTION
46
(G/W)– Shield – – – – Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB1990E
SKIB1990E
SKIB1990E
PKIB6116J
SKIB1990E
SKIB1990E

TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
AV-83
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
Camera Control UnitNKS0048S
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
5–Shield –– – –
6
(P/L)Ground Camera image signal Input ONSet selector lever in R posi-
tion, and then display the
rear view image.
7
(G/B)GroundRear view camera
ground– ON – Approx. 0 V
8
(GR)Ground Camera ON signal Output ONSet selector lever in R posi-
tion, and then display the
rear view image.Approx. 6 V
11 – S h i e l d – – – –
12
(Y)Ground Camera image signal Output ONSet selector lever in R posi-
tion, and then display the
rear view image.
14
(V)GroundCamera-connection rec-
ognition signalOutput ON – Approx. 0 V
17
(G)–Communication signal
(L)Input/
Output–– –
18
(R)–Communication signal
(H)Input/
Output–– –
19
(B)–Communication signal
(L)Input/
Output–– –
20
(W)–Communication signal
(H)Input/
Output–– –
22
(LG)Ground Reverse signalInput/
OutputONSelect lever in R position. Approx. 12 V
Other than selector lever in
R position.Approx. 0 V
SKIB2251J
SKIB2251J

DIAGNOSIS SYSTEM
AV-87
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
On Board Diagnosis Item
*1: With navigation system
*2: With rear view monitor
STARTING PROCEDURE
1. Start the engine.
2. Turn the audio system OFF.
3. While pushing the “SETTING” button, turn the volume control
dial clockwise or counterclockwise for 40 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
Shifting from current screen to previous screen is performed
by pushing “BACK” button.
Mode Description
Self Diagnosis
AV (NAVI) control unit diagnosis and connection diagnosis between
AV (NAVI) control unit and each unit
The DVD-ROM drive diagnosis of NAVI control unit and the connec-
tion diagnosis between NAVI control unit and GPS antenna can be
performed
(DVD-ROM drive will not be diagnosed when no map DVD-ROM is in
it.)
Confirmation/
AdjustmentDisplay DiagnosisThe tint can be confirmed by the color spectrum bar display. The shad-
ing of color can be confirmed by the gradation bar display.
Vehicle SignalsDiagnosis of signals can be performed for vehicle speed, parking brake,
lights, ignition switch, and reverse.
Speaker Test The connection of a speaker can be confirmed by test tone.
Climate Control Start auto air conditioner system self-diagnosis.
Navigation
*1
Steering Angle
AdjustmentWhen there is a difference between the actual turning angle and the
vehicle mark turning angle, it can be adjusted.
Speed CalibrationWhen there is a difference between the current location mark and the
actual location, it can be adjusted.
Error HistoryThe system malfunction and the frequency when occurred in the past
are displayed. When the malfunctioning item is selected, the time and
place that the selected malfunction last occurred are displayed.
Synchronizer FES clock -
Vehicle CAN Diagnosis The transmitting/receiving of CAN communication can be monitored.
AV COMM DiagnosisThe communication condition of each unit of Multi AV system can be
monitored.
Handsfree PhoneThe received volume adjustment of hands-free phone, microphone
speaker check, and erase memory can be performed.
Camera Cont.
*2The signal connected to camera control unit can be checked and the
guiding line position that overlaps rear view camera image can be
adjusted.
Bluetooth The passkey and the name of device can be checked and changed
Delete Unit Connection Log Erase the connection history of unit and error history
SKIB3655E

AV-92
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
Revision: 2006 January2006 M35/M45
VEHICLE SIGNALS
A comparison check can be made of each actual vehicle signal and
the signals recognized by the system.
SPEAKER TEST
When selecting “Speaker Test”, speaker diagnosis screen is dis-
played. When pressing “Start”, test tone emits from the speaker. At
that time, when pressing “Start”, test tone emits from next speaker.
Then, when pressing the “END”, test tone stops.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
CLIMATE CONTROL
For details, refer to ATC-55, "Self-diagnosis Function" .
SKIB3663E
Diagnosis itemDis-
playVehicle status Remarks
Vehicle speedON Vehicle speed > 0 km/h (0 MPH)
Changes in indication may be delayed. This is nor-
mal. OFF Vehicle speed = 0 km/h (0 MPH)
— Ignition switch in ACC position
Parking brakeON Parking brake is applied.
OFF Parking brake is released.
LightsON Light switch ON
–
OFF Light switch OFF
IgnitionON Ignition switch ON
–
OFF Ignition switch in ACC position
ReverseON Selector lever in R position
Changes in indication may be delayed. This is nor-
mal. OFFSelector lever in any position
other than R
— Ignition switch in ACC position
Tw e e t e r : 3 k H z
Front door speaker : 300 Hz
Rear door speaker : 1 kHz
Rear surround speaker : 1 kHz
Center speaker : 1 kHz
Woofer : 100 Hz
Seat speaker : 1 kHz
SKIB3664E

AV-94
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
DIAGNOSIS SYSTEM
Revision: 2006 January2006 M35/M45
With NAVI
Count Down Type
When the error is detected, set the counter to 40. If the system is normal when turning the ignition switch
ON, the counter decreases by 1.
The lower limit of the counter is 1. It can be reset to 0 by “Delete log” switch or CONSULT-II.
Count Up Type
When the ignition switch is turned ON if the error is detected, the counter increases 1. Even if it is normal
when the ignition switch is turned ON the next time, the counter does not decrease.
The upper limit of the counter is 50. 51 or more is displayed as 50. It can be reset to 0 by “Delete log”
switch or CONSULT-II.
Error Item
Some error items may be displayed simultaneously according to the cause. If some error items are displayed
simultaneously, the detection of the cause can be performed by the combination of display items
SKIB3687E
Display type of occur-
rence frequencyError history display item
Count down type CAN_COMM_CIRCUIT, CONTROL UNIT (CAN), AV COMM CIRCUIT, CONTROL UNIT (AV)
Count up type Other than the above
Error item Description Possible cause/Action to take
CAN_COMM_CIRCUITCAN communication malfunction is
detectedPerform the diagnosis using CONSULT-II,
and then repair the malfunctioning parts
based on diagnostic results.
Refer to AV-103, "
SELF-DIAG RESULTS"
.
CONTROL UNIT (CAN) CAN initial diagnosis malfunction is
detectedReplace AV (NAVI) control unit
Refer to AV-135, "
AV (NAVI) Control Unit"
CONTROL UNIT (AV) AV communication circuit initial diagno-
sis malfunction is detectedReplace AV (NAVI) control unit
Refer to AV-135, "AV (NAVI) Control Unit"
AV COMM CIRCUIT
Switches Connection Error
DVD Deck Connection Error
Audio Unit Connection Error
Amplifier Connection Error
Rearview Camera Connection ErrorMalfunction is detected on communi-
cation circuit between AV (NAVI) con-
trol unit and DVD player
Communication circuit between AV
(NAVI) control unit and DVD player
AV (NAVI) control unit
DVD player

DIAGNOSIS SYSTEM
AV-95
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
AV COMM CIRCUIT
Switches Connection Error
Audio Unit Connection Error
Amplifier Connection Error
Rearview Camera Connection ErrorBOSE surround 5.1ch system
Malfunction is detected on communi-
cation circuit between DVD player
and multifunction switch
Communication circuit between DVD
player and multifunction switch
DVD player
Multifunction switch
BOSE 2ch system
Malfunction is detected on communi-
cation circuit between AV (NAVI)
control unit and multifunction switch
Communication circuit between AV
(NAVI) control unit and multifunction
switch
AV (NAVI) control unit
Multifunction switch
AV COMM CIRCUIT
Audio Unit Connection Error
Amplifier Connection Error
Rearview Camera Connection ErrorMalfunction is detected on communi-
cation circuit between multifunction
switch and camera control unit
Communication circuit between multi-
function switch and camera control unit
Multifunction switch
Camera control unit
AV COMM CIRCUIT
Audio Unit Connection Error
Amplifier Connection ErrorBase system
Audio unit power supply and ground
circuit malfunction is detected
Malfunction is detected on communi-
cation circuit between multifunction
switch and audio unit
Malfunction is detected on communi-
cation signal between audio unit and
AV (NAVI) control unit
Audio unit power supply and ground cir-
cuit
Communication circuit between multi-
function switch and audio unit
Multifunction switch
Audio unit
AV (NAVI) control unit
BOSE system
Malfunction is detected on communi-
cation circuit between camera con-
trol unit and BOSE amp
Communication circuit between camera
control unit and BOSE amp
Camera control unit
BOSE amp
AV COMM CIRCUIT
Audio Unit Connection Error
Audio unit power supply and ground
circuit malfunction is detected
Malfunction is detected on communi-
cation circuit between BOSE amp
and audio unit
Malfunction is detected on communi-
cation signal between audio unit and
AV (NAVI) control unit
Audio unit power supply and ground cir-
cuit
Communication circuit between BOSE
amp and audio unit
Audio unit
AV (NAVI) control unit
AV COMM CIRCUIT
Rearview Camera Connection Error
Camera control unit power supply
and ground circuit malfunction is
detected
Malfunction is detected on communi-
cation signal between camera con-
trol unit and AV (NAVI) control unit
Camera control unit power supply and
ground circuit
Camera control unit
AV (NAVI) control unit
AV COMM CIRCUIT
Switches Connection Error
Multifunction switch power supply
and ground circuit malfunction is
detected
Malfunction is detected on communi-
cation signal between multifunction
switch and AV (NAVI) control unit
Multifunction switch power supply and
ground circuit
Multifunction switch
AV (NAVI) control unit
AV COMM CIRCUIT
DVD Deck Connection Error
DVD player power supply and
ground circuit malfunction is
detected
Malfunction is detected on communi-
cation signal between DVD player
and AV (NAVI) control unit
DVD player power supply and ground
circuit
DVD player
AV (NAVI) control unit Error item Description Possible cause/Action to take

DIAGNOSIS SYSTEM
AV-97
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
VEHICLE CAN DIAGNOSIS
CAN communication status and error counter is displayed.
Error counter displays 0 if any malfunction is not detected in the
past. If the malfunction is detected, it displays 40. When turning
the ignition switch ON, if it is normal, it displays 39. The lower
limit of the counter is 1.
If it is reset, the error counter is deleted.
NOTE:
“???” indicates “UNKWN”.
AV COMM DIAGNOSIS
Displays the communication condition between AV (NAVI) con-
trol unit (master unit) and each unit and between audio unit
(sub-master unit) and each unit.
Error counter displays 0 if any malfunction is not detected in the
past. If the malfunction is detected, it displays 40. When turning
the ignition switch ON, if it is normal, it displays 39. The lower
limit of the counter is 1.
If it is reset, the error counter is deleted.
ITM: AV (NAVI) control unit
NOTE:
“???” indicates “UNKWN”.Items Display (Current)Error counter
(Past)
Tx (HVAC) OK /??? 0 - 40
Rx (ECM) OK /??? 0 - 40
Rx (Cluster) OK /??? 0 - 40
Rx (BCM) OK /??? 0 - 40
Rx (HVAC) OK /??? 0 - 40
Rx (USM) OK /??? 0 - 40
Rx (TPMS) OK /??? 0 - 40
SKIB3666E
ItemsStatus
(Current)Counter
(Past)
C Tx (ITM-PrimarySW) OK /??? 0 - 40
C Rx (PrimarySW-ITM) OK /??? 0 - 40
C Rx (STRG SW-ITM) OK /??? 0 - 40
C Rx (RrSeatSW-ITM) OK /??? 0 - 40
C Rx (Audio-ITM) OK /??? 0 - 40
C Rx (Amp-ITM) OK /??? 0 - 40
C Rx (RearCamera-ITM) OK /??? 0 - 40
C Rx (DVD-ITM) OK /??? 0 - 40
C Rx (Amp-Audio) OK /??? 0 - 40
C Rx (DVD-Audio) OK /??? 0 - 40SKIB3667E