rear entertainment INFINITI M35 2006 Factory Workshop Manual

AV-142
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
REMOVAL AND INSTALLATION
Revision: 2006 January2006 M35/M45
Camera Control UnitNKS004A4
REMOVAL
1. Remove trunk side finisher (RH). Refer to EI-56, "Removal and Installation for Trunk Room Trim" .
2. Remove screws (A) and disconnect connector, and remove rear
view camera control unit (1).
3. Remove screws (A) and remove bracket (1).
INSTALLATION
Installation is the reverse order of removal.
Rear View CameraNKS004A5
REMOVAL
1. Remove trunk lid finisher inner. Refer to EI-56, "TRUNK ROOM TRIM & TRUNK LID FINISHER" .
2. Remove screws attaching camera and camera bracket.
3. Remove connector and connector clip.
4. Remove camera bracket (1) while pushing right direction of
vehicle.
INSTALLATION
1. Install rear view camera and camera bracket while pressing to trunk room side.
2. Install connector and connector clip.
3. Install trunk lid finisher inner.
Steering Angle SensorNKS004A6
REMOVAL
1. Remove combination switch. Refer to SRS-40, "SPIRAL CABLE" .
SKIB4398E
SKIB4399E
SKIB5010E

AV-148
[WITH MOBILE ENTERTAINMENT SYSTEM]
SYSTEM DESCRIPTION
Revision: 2006 January2006 M35/M45
GPS (Global Positioning System)
GPS (Global Positioning System) was developed for and is con-
trolled by the US Department of Defense. The system utilizes GPS
satellites (NAVSTAR), sending out radio waves while flying on an
orbit around the earth at an altitude of approximately 21,000 km
(13,100miles).
The GPS receiver calculates the vehicle's position in three dimen-
sions (latitude/longitude/altitude) according to the time lag of the
radio waves received from four or more GPS satellites (three-dimen-
sional positioning). If radio waves were received only from three
GPS satellites, the GPS receiver calculates the vehicle's position in
two dimensions (latitude/longitude), utilizing the altitude data calcu-
lated previously with radio waves from four or more GPS satellites
(two-dimensional positioning).
Position correction by GPS is not available while the vehicle is stopped.
Accuracy of GPS will deteriorate under the following conditions:
In two-dimensional positioning, GPS accuracy will deteriorate when altitude of the vehicle position
changes.
The accuracy can be even lower depending on the arrangement of the GPS satellites utilized for the posi-
tioning.
Position detection is not possible when vehicle is in an area where radio waves from the GPS satellite do
not reach, such as in a tunnel, parking lot in a building, and under an elevated highway. Radio waves from
the GPS satellites may not be received when some object is located over the GPS antenna.
NOTE:
Even a high-precision three dimensional positioning, the detection result has an error about 10 m (30ft).
Because the signals of GPS satellite is controlled by the Tracking and Control Center in the United States,
the accuracy may be degraded lower intentionally or the radio waves may stop.
MOBILE ENTERTAINMENT SYSTEM
The wireless headphone has been adopted to the rear seat. It is possible to listen to a separate sound in
front seat and rear seat and to see a separate image in front display and rear display.
When headphone mode is turned ON at radio/CD changer mode, AUX or DVD mode is turned ON only for
rear seat. The image that is different from front seat is displayed and a separate sound is output from
speaker and headphone.
HANDS-FREE PHONE
AV (NAVI) control unit has a Bluetooth module. It can perform wireless hands-free telephone calls using
the portable phone in a pocket.
5 or more portable phones can be registered into the AV (NAVI) control unit.
REAR VIEW MONITOR
The small CCD camera is equipped into the rear end of the vehicle. The rear view monitor that displays
the area behind the vehicle while backing up is equipped.
Guiding lines indicating side and rear clearances are provided in the rear view monitor image, which
allows the driver to more easily judge distances between the vehicle and objects in the display. The possi-
ble route lines that indicate the possible route according to the steering angle are provided to help backing
up when parking.
Image quality of the rear view image and of the navigation screen can be adjusted separately.
SEL526V

SYSTEM DESCRIPTION
AV-151
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
REAR DISPLAY UNIT
It receives the image signal from the video distributor.
The changing of image is controlled by the communication with
video distributor.
It receives the operation signal from remote control, and then
sends it to the video distributor.
VIDEO DISTRIBUTOR
It receives the image signal from the AV (NAVI) control unit,
DVD player, and auxiliary input jack, and then sends it to the
front display and rear display.
It supplies the power to the remote control receiver, and then
receives the operation signal from the remote control receiver.
It sends ON signal to headphone amp.
DVD PLAYER
BOSE 2ch System
It sends the sound signal when playing DVD to the audio unit,
headphone amp, and then it sends the image signal to the video
distributor.
It inputs the sound signal from auxiliary input jacks, and then
sends it to audio unit, headphone amp.
BOSE Surround 5.1ch System
It sends the sound signal when playing DVD to the BOSE amp, headphone amp, and then it sends the
image signal to the video distributor.
When the downmix function is turned ON when playing DVD, the sound signal is sent to the audio unit.
It inputs the sound signal from auxiliary input jacks, and then sends it to audio unit, headphone amp.
CAMERA CONTROL UNIT
When the reverse signal is input, the power is supplied to the
rear view camera, and then the image signal from the rear view
camera is sent to the display unit.
The camera control unit displays the guiding lines and possible
route lines, and then it synthesizes them to the camera image.
SKIB3895E
SKIB3897E
SKIB3889E
SKIB3898E

AV-206
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
BOSE AmpNKS004AM
51
(R)GroundCommunication signal
(SAT-AUDIO)Input ON Satellite radio mode is ON.
53 Ground Antenna amp ON signal Output ON
Approx.12V
54 – AM-FM main Input – – –
55 – FM sub Input – – –Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switch Operation
SKIB3824E
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
14
(G)–Communication signal
(L)–– – –
15
(G)–Communication signal
(L)–– – –
16
(BR)Ground ACC power supply Input ACC – Battery voltage
23
*
(L/R)3
*
(L/G)DVD sound signal front
LHInput ON
When playing DVDCAUTION
24*
(B/Y)4
*
(LG)DVD sound signal front
RHInput ON
When playing DVDCAUTION
25*
(B)5
*
(W)DVD sound signal rear
LHInput ON
When playing DVDCAUTION
26*
(P)6
*
(L)DVD sound signal rear
RHInput ON
When playing DVDCAUTION
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E

AV-208
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
41
(L)42
(B/W)Audio signal front LH Output ON Receive audio signal.
43
(BR)44
(B/R)Audio signal front RH Output ON Receive audio signal.
45
(BR)46
(B/R)Audio signal woofer Output ON Receive audio signal.
47
(B/W)Ground Ground – ON – Approx. 0 V
50
(Y)Ground Battery power supply Input OFF – Battery voltage
51
(R)Ground Battery power supply Input OFF – Battery voltage
52
(B/W)Ground Ground – ON – Approx. 0 V
54
(LG)49
(B/Y)Audio signal rear LH Output ON Receive audio signal.
56
*
(B/W)69
*
(L)Audio signal passenger
seat LHOutput ON Receive audio signal.
57
(O/B)58
(W/R)Audio signal
centerOutput ON Receive audio signal. Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB3609E
SKIB3609E
PKIB6116J
SKIB3609E
SKIB3609E
SKIB3609E

TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
AV-209
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
*: BOSE surround 5.1ch system
CAUTION:
When the stereo sound is played, only front RH and LH are input. When the monaural sound is played, only center is input. All
surround sounds are input only when the 5.1 channel surround sound is played. 59
*
(B)72
*
(W)Audio signal rear sur-
round LHOutput ON Receive audio signal.
62
*
(G/Y)73
*
(GY/R)Audio signal rear sur-
round RHOutput ON Receive audio signal.
63
*
(B/W)74
*
(L)Audio signal driver seat
LHOutput ON Receive audio signal.
64
*
(B/R)75
*
(BR)Audio signal driver seat
RHOutput ON Receive audio signal.
68
(O)55
(B/P)Audio signal rear RH Output ON Receive audio signal.
71
*
(Y)70
*
(BR)Audio signal passenger
seat RHOutput ON Receive audio signal. Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E
SKIB3609E

AV-212
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
46
(L/Y)47
(G)RGB signal (B: blue) Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
47
(G)Ground RGB ground – ON – Approx. 0 V
48
(B)GroundRGB synchronizing sig-
nalOutput ON –
49 – Shield – – – –
50
(G)Ground RGB area (YS) signal Output ONWhen inputting RGB image. Approx. 5 V
Set the selector lever in R
position, and then display
the rear view image.
51
(W)GroundHorizontal synchronizing
(HP) signalInput ON –
52
(R)GroundVertical synchronizing
(VP) signalInput ON –
53
(O/L)GroundCommunication signal
(CONT-DISP)Input ONWhen adjusting display
brightness. Te r m i n a l
(Wire color)
ItemSignal
Input/
outputCondition
Reference value
+–Ignition
switchOperation
SKIB2237J
SKIB3603E
PKIB4948J
SKIB3601E
SKIB3598E
PKIB5039J

TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
AV-213
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
*: With navigation system54
(W/L)GroundCommunication signal
(DISP-CONT)Input ONWhen adjusting display
brightness.
55 – Shield – – – –
61
(LG)Ground Illumination signal Input OFFLighting switch is OFF. Approx. 0 V
Lighting switch is ON. Approx. 12 V
63
(Y/G)Ground Ignition signal Input ON – Battery voltage
64
(P)Ground Parking brake signal Input ONParking brake ON. Approx. 0 V
Parking brake OFF. Approx. 12 V
65
(O)Ground Reverse signal Input ONSelect lever in R position. Approx. 12 V
Other than selector lever in
R position.Approx. 0 V
66
(G)GroundVehicle speed signal
(8-pulse)Input ONWhen vehicle speed is
approx. 40 km/h (25 MPH).
67
(V)GroundCamera-connection rec-
ognition signalInput ONConnected to rear view
camera control unit connec-
tor.Approx. 0 V
Not connected to rear view
camera control unit connec-
tor.Approx. 5 V
69
(W)–Communication signal
(H)Input/
Output–– –
70
(R)–Communication signal
(L)Input/
Output–– –
71
(LG)–CAN-HInput/
Output–– –
72
(P)–CAN-LInput/
Output–– –
107
*Ground GPS signal Input ON Connector is not connected. Approx. 5 V Terminal
(Wire color)
ItemSignal
Input/
outputCondition
Reference value
+–Ignition
switchOperation
PKIB5039J
SKIA6649J

TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
AV-215
[WITH MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
14
(L/G)GroundRGB area (YS) signal
(front)Output ONWhen inputting RGB image. Approx. 5 V
Set the selector lever in R
position, and then display
the rear view image.
15
(W/L)GroundHorizontal synchronizing
(HP) signal (front)Input ON –
16
(O/L)GroundVertical synchronizing
(VP) signal (front)Input ON –
17
(L/Y)GroundRGB synchronizing
signal (front)Output ON –
18 – Shield – – – –
19
(R)Ground AUX image signal Input ON AUX image
21 – Shield – – – –
22 – Shield – – – –
23
(L)Ground DVD image signal Input ON DVD image Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
SwitchOperation
PKIB4948J
SKIB3601E
SKIB3598E
SKIA3222J
SKIB2251J
SKIB2251J

AV-216
[WITH MOBILE ENTERTAINMENT SYSTEM]
TERMINALS AND REFERENCE VALUE FOR CONTROL UNIT
Revision: 2006 January2006 M35/M45
25
(B)27
(G)RGB signal (R: red)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
26
(W)27
(G)RGB signal (G: green)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
27
(G)Ground RGB ground – ON – Approx. 0 V
28
(R)27
(G)RGB signal (B: blue)
(rear)Output ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
29
(W/R)GroundVertical synchronizing
(VP) signal
(rear)Input ON –
30
(W)GroundHorizontal synchronizing
(HP) signal (rear)Input ON –
31 – Shield – – – –
32
(R/L)GroundRGB area (YS) signal
(rear)Output ONWhen inputting RGB image. Approx. 5 V
Rear display
DVD image Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference value
+–Ignition
SwitchOperation
SKIB2238J
SKIB2236J
SKIB2237J
SKIB0823E
SKIB0825E
PKIB4949J