INSTALLATION INFINITI QX4 2001 Factory Manual PDF

SBT495
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
EXTERIOR
Removal and Installation (Cont'd)
BT-37

SBT491
EXTERIOR
Removal and Installation (Cont'd)
BT-38

SBT496-A
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
EXTERIOR
Removal and Installation (Cont'd)
BT-39

SBT028A
EXTERIOR
Removal and Installation (Cont'd)
BT-40

Removal and InstallationNBBT0014IWhen removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
HFor Wiring Diagram, refer to EL-181, ªPOWER SEATº for details.
CAUTION:
IBefore removing the front seat, turn the ignition switch off, disconnect both battery cables and wait
at least 3 minutes.
IWhen checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
IDo not drop, tilt, or bump the side air bag module installed in the seat. Always handle it with care.
SBT066A
SBT067A
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
FRONT SEAT
Removal and Installation
BT-41

SBT019A
FRONT SEAT
Removal and Installation (Cont'd)
BT-42

HEATED SEAT=NBBT0014S03IWhen handling seat, be extremely careful not to scratch heating unit.
ITo replace heating unit, seat trim and pad should be separated.
IDo not use any organic solvent, such as thinner, benzene, alcohol, gasoline, etc. to clean trims.
HFor Wiring Diagram, refer to EL-183, ªHEATED SEATº for details.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
FRONT SEAT
Removal and Installation (Cont'd)
BT-43

Removal and InstallationNBBT0015
SBT190-A
REAR SEAT
Removal and Installation
BT-44

AdjustmentNBBT0016Install motor & limit SW assembly and sunroof rail assembly in the following sequence:
1. Arrange equal lengths of link and wire assemblies on both sides of sunroof opening.
2. Connect sunroof connector to sunroof switch and positive (+) power supply.
3. Set lid assembly to fully closed position
by operating OPEN switch and TILT switch.
4. Fit outer side of lid assembly to the surface of roof on body outer panel.
5. Remove motor, and keep OPEN switch pressed until motor pinion gear reaches the end of its rotating
range.
6. Install motor.
7. Check that motor drive gear fits properly in wires.
8. Press TILT-UP switch to check lid assembly for normal tilting.
9. Check sunroof lid assembly for normal operations (tilt-up, tilt-down, open, and close).
SBF920F
Removal and InstallationNBBT0017IAfter any adjustment, check sunroof operation and lid align-
ment.
IHandle finisher plate and glass lid with care so not to cause
damage.
IIt is desirable for easy installation to mark each point before
removal.
CAUTION:
IAlways work with a helper.
IBefore removal, fully close the glass lid assembly, then
after removal, do not move motor assembly.
GI
MA
EM
LC
EC
FE
AT
TF
PD
AX
SU
BR
ST
RS
HA
SC
EL
IDX
SUNROOF
Adjustment
BT-45

SBT515-C
*1 BT-32 *2 EL-174
SUNROOF
Removal and Installation (Cont'd)
BT-46