INFINITI QX4 2005 Factory Service Manual

WW-52
REAR WIPER AND WASHER SYSTEM
Revision: October 20052005 QX56
Removal and Installation of Rear Wiper Arm, Adjustment of Rear Wiper Arm
Stop Location
EKS00BEN
REMOVAL
1. Operate the rear wiper motor and stop it at the auto stop position.
2. Remove rear wiper arm cover by gripping bottom edge and
rotating cover up. Remove mounting nut, and remove the wiper
arm.
INSTALLATION
1. Prior to wiper arm installation, turn on wiper switch to operate wiper motor and then turn it "OFF" (Auto
Stop).
2. Clean up the pivot area as illustrated. This will reduce the possi-
bility of wiper arm looseness.
3. Install rear wiper arm so that the arm rests in the stopper and
tighten wiper arm nut.
LKIA0608E
SEL024J

REAR WIPER AND WASHER SYSTEM
WW-53
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Removal and Installation of Rear Wiper Motor EKS00BEO
REMOVAL
1. Remove rear wiper arm. Refer to WW-52, "Removal and Instal-
lation of Rear Wiper Arm, Adjustment of Rear Wiper Arm Stop
Location" .
2. Remove pivot cap.
3. Remove back door finisher lower. Refer to EI-42, "
BACK DOOR
TRIM" .
4. Remove the glass hatch latch assembly. Refer to BL-135,
"BACK DOOR LOCK" .
5. Disconnect rear wiper motor connector.
6. Remove rear wiper motor mounting bolts, and remove rear
wiper motor.
INSTALLATION
CAUTION:

Do not drop the wiper motor or cause it to contact other parts.
WKIA5018E
1. Wiper arm cover 2. Wiper arm and blade 3. Pivot cap
4. Rear wiper motor 5. Wiper arm stop
LKIA0416E

WW-54
REAR WIPER AND WASHER SYSTEM
Revision: October 20052005 QX56
1. Clean up the pivot area as illustrated. This will reduce possibility
of wiper arm looseness.
2. Install rear wiper motor to the vehicle.
3. Connect rear wiper motor connector.
4. Install glass hatch latch assembly and adjust as necessary.
Refer to BL-135, "
BACK DOOR LOCK" .
5. Install back door finisher lower. Refer to EI-42, "
BACK DOOR
TRIM" .
6. Attach pivot cap.
7. Attach wiper arm. Refer to WW-52, "
Removal and Installation of
Rear Wiper Arm, Adjustment of Rear Wiper Arm Stop Location" .
Rear Washer Nozzle AdjustmentEKS00BEP

This vehicle is equipped with a non-adjustable rear washer nozzle.

If not satisfied with washer fluid spray coverage, confirm that the washer nozzle is installed correctly.

If the washer nozzle is installed correctly, and the washer fluid spray coverage is not satisfactory, replace
the washer nozzle.
Rear Washer Tube LayoutEKS00BEQ
Removal and Installation of Rear Washer NozzleEKS00BER
REMOVAL
1. Remove the rear spoiler. Refer to EI-26, "REAR SPOILER" .
2. Remove rear washer tube from nozzle.
3. Release retaining clips, and remove washer nozzle.
INSTALLATION
Installation is in the reverse order of removal.
SEL024J
WKIA1925E
LKIA0418E

REAR WIPER AND WASHER SYSTEM
WW-55
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Check ValveEKS00BES

A check valve is provided in the washer fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
Removal and Installation of Rear Wiper and Washer SwitchEKS00BET
Refer to WW-33, "Removal and Installation of Wiper and Washer Switch" .
Removal and Installation of Washer TankEKS00BEU
Refer to WW-33, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer MotorEKS00BEV
Refer to WW-34, "Removal and Installation of Washer Motor" .
PKIA2546E

WW-56
POWER SOCKET
Revision: October 20052005 QX56
POWER SOCKETPFP:253A2
Wiring Diagram — P/SCKT — EKS00BEW
WKWA4494E

POWER SOCKET
WW-57
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Removal and Installation of Power SocketsEKS00BEX
REMOVAL
1. Disconnect battery negative terminal before removing front
power socket LH and rear cargo power socket. Remove inner
socket from the ring, while pressing the hook on the ring out
from square hole.
2. Disconnect power socket connector.
3. Remove ring from power socket finisher while pressing pawls.
INSTALLATION
Installation is in the reverse order of removal.
WKIA1035E

WW-58
HORN
Revision: October 20052005 QX56
HORNPFP:25610
Wiring Diagram — HORN — EKS00BEY
WKWA4495E

HORN
WW-59
C
D
E
F
G
H
I
J
L
MA
B
WW
Revision: October 20052005 QX56
Removal and InstallationEKS00BEZ
REMOVAL
1. Remove the front grille. Refer to EI-17, "FRONT GRILLE" .
2. Disconnect horn connector.
3. Remove horn bolt and remove horn from vehicle.
INSTALLATION
1. Tighten horn bolt to specified torque.
2. Reconnect horn connector.
3. Install front grille. Refer to EI-17, "
FRONT GRILLE" .
LKIA0419E
Horn bolt : 17 N·m (1.7 kg-m, 13 ft-lb)

WW-60
HORN
Revision: October 20052005 QX56