key INFINITI QX56 2010 Factory Service Manual

DLK-58
< COMPONENT DIAGNOSIS > [WITH
INTELLIGE NT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
CO MPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Descr iptionINFOID:0 000000005146905
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
v ehicle is equipped with many ele ct ronic control uni t, and each control unit shares information and links with
other control units during operation (not independent). In CAN communicat ion, control units are connected
wi
th 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of inf ormation transmission with less
wiring
. Each control unit transmits/receives data but selectively reads required data only.
CAN
Communication Signal Chart. Refer to LAN-44, "CAN Communication Signal Chart".
DTC LogicINFOID:0 000000005146906
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0 000000005146907
1.PERFORM SELF DIAGNOSTIC
1.T urn ignition switch ON and wait for 2 second or more.
2. Check “S elf Diagnostic Res ult”.
Is“CAN CO MM CIRCUIT” displayed?
YES>> Refer to LAN-14, " TroubleDiagnosisF low Chart".
NO>> Refer to GI-38, "Intermittent Incident".
DTC CONSULT
-III displa y
description DTC Detection ConditionPossible cause
U100
0C AN COMM CIRCUIT
W hen BCM can not communicate CAN com-
munication s ignal continuously for 2 sec-
onds o r more.
In CAN communication s ystem, any item (or item s)
of the following listed below is malfunctio ning.
•Transmission
•Receiving (ECM)
•R eceiving (VDC/TCS/AB S)
•Receiving (METER/M& A)
•Receiving (TCM)
•Rec eiving (MULTI A V)
•Receiving (IPDM E/R)
Revision: April 2009 2010 QX56

U1010 CONTROL UNIT (CAN)DLK-59
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000005146908
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146909
1.REPLACE BCM
When DTC [U1010] is detected, replace BCM.
>> Replace BCM. Refer to BCS-59, "
Removal and Installation".
Special Repair RequirementINFOID:0000000005146910
1.REQUIRED WORK WHEN REPLACING BCM
The BCM must be initialized when replaced. Refer to BCS-3, "
CONFIGURATION : Description" for BCM con-
figuration.
Initialize NVIS by CONSULT-III. For the details of initialization refer to CONSULT-III operation manual.
>> Work end.
DTC CONSULT-III display de-
scription DTC Detection Condit
ion Possible cause
U1010 CONTROL UNIT (CAN) BCM detected internal CAN communication circuit malfunction. BCM
Revision: April 20092010 QX56

DLK-60
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
CENTER CONSOLE AREA ANTENNA (REAR)
CENTER CONSOLE AREA ANTENNA (REAR)
DescriptionINFOID:0000000005146911
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146912
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT1”.
3. When Intelligent Key is in center console area antenna (rear) detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Center console area antenna (rear) is OK.
NO >> Refer to DLK-60, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146913
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Center console area antenna (rear) is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and center console area antenna (rear) connectors.
2. Check continuity between Intelligent Key unit harnes s connector (A) M70 terminals 15, 16 and center con-
sole area antenna (rear) harness connector (B) M209 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT1 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Center console area antenna (rear)
• Between Intelligent Key unit and center console area an-
tenna (rear)
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 15 Ground Ignition
switch is
pushed.
ALKIA0585ZZPIIB7441E
Revision: April 20092010 QX56

CENTER CONSOLE AREA ANTENNA (REAR)DLK-61
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 15, 16 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key unit and center console area antenna (rear).
3.CHECK INSIDE KEY ANTENNA POWER SUPPLY SINGAL
1. Replace center console area antenna (rear). (New antenna or other antenna)
2. Connect Intelligent Key unit connector.
3. Check signal between Intelligent Key unit connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace center console area antenna (rear).
NO >> Replace Intelligent Key unit. Refer to SEC-120, "
Removal and Installation".
Intelligent Key
unit connectorTe r m i n a l sCenter console area
antenna (rear) con-
nector Terminals Continuity
A: M70 15
B: M209 1
Ye s
16 2
Item Connector TerminalsContinuity
Intelligent Key unit A: M70 15
Ground No
16
ALKIA0586ZZ
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 15 Ground Ignition
switch is
pushed.
ALKIA0585ZZ
PIIB7441E
Revision: April 20092010 QX56

DLK-62
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
LUGGAGE AREA ANTENNA
LUGGAGE AREA ANTENNA
DescriptionINFOID:0000000005146914
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146915
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT1”.
3. When Intelligent Key is in luggage area antenna detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Luggage area antenna is OK.
NO >> Refer to DLK-62, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146916
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Luggage area antenna is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and luggage area antenna connectors.
2. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 35, 36 and luggage
area antenna harness connector (B) B76 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT1 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Luggage area antenna
• Between Intelligent Key unit and luggage area antenna
Connector Item
Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 35 Ground Ignition
switch is
pushed.
ALKIA0587ZZPIIB7441E
Revision: April 20092010 QX56

LUGGAGE AREA ANTENNADLK-63
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 35, 36 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key unit and luggage area antenna.
3.CHECK INSIDE KEY ANTENNA POWER SUPPLY SINGAL
1. Replace luggage area antenna. (New antenna or other antenna)
2. Connect Intelligent Key unit connector.
3. Check signal between Intelligent Key unit connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace luggage area antenna.
NO >> Replace Intelligent Key unit. Refer to SEC-120, "
Removal and Installation".
Intelligent Key
unit connectorTe r m i n a l sLuggage area an-
tenna connector Terminals Continuity
A: M70 35
B: B76 1
Ye s
36 2
Item Connector TerminalsContinuity
Intelligent Key unit A: M70 35
Ground No
36
ALKIA0588ZZ
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 35 Ground Ignition
switch is
pushed.
ALKIA0587ZZ
PIIB7441E
Revision: April 20092010 QX56

DLK-64
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
CENTER CONSOLE AREA ANTENNA (FRONT)
CENTER CONSOLE AREA ANTENNA (FRONT)
DescriptionINFOID:0000000005146917
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146918
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT2”.
3. When Intelligent Key is in center console area antenna (front) detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Center console area antenna (front) is OK.
NO >> Refer to DLK-64, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146919
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Center console area antenna (front) is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and c enter console area antenna (front) connectors.
2. Check continuity between Intelligent Key unit harnes s connector (A) M70 terminals 13, 14 and center con-
sole area antenna (front) harness connector (B) M210 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT2 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Center console area antenna (front)
• Between Intelligent Key unit and center console area an-
tenna (front)
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 13 Ground Ignition
switch is
pushed.
ALKIA0583ZZPIIB7441E
Revision: April 20092010 QX56

CENTER CONSOLE AREA ANTENNA (FRONT)DLK-65
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 13, 14 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key unit and center console area antenna (front).
3.CHECK INSIDE KEY ANTENNA POWER SUPPLY SINGAL
1. Replace center console area antenna (front). (New antenna or other antenna)
2. Connect Intelligent Key unit connector.
3. Check signal between Intelligent Key unit connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace center console area antenna (front).
NO >> Replace Intelligent Key unit. Refer to SEC-120, "
Removal and Installation".
Intelligent Key
unit connectorTe r m i n a l sCenter console area
antenna (front) con-
nector Terminals Continuity
A: M70 13
B: M210 1
Ye s
14 2
Item Connector TerminalsContinuity
Intelligent Key unit A: M70 13
Ground No
14
ALKIA0584ZZ
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 13 Ground Ignition
switch is
pushed.
ALKIA0583ZZ
PIIB7441E
Revision: April 20092010 QX56

DLK-66
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
OVERHEAD CONSOLE AREA ANTENNA
OVERHEAD CONSOLE AREA ANTENNA
DescriptionINFOID:0000000005146920
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146921
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT2”.
3. When Intelligent Key is in overhead consol e area antenna detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Overhead console area antenna is OK.
NO >> Refer to DLK-66, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146922
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Overhead console area antenna is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and overhead console area antenna connectors.
2. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 33, 34 and overhead console area antenna harness connector (B) R210 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT2 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Overhead console area antenna
• Between Intelligent Key unit and overhead console area
antenna
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 33 Ground Ignition
switch is
pushed.
ALKIA0589ZZPIIB7441E
Revision: April 20092010 QX56

OVERHEAD CONSOLE AREA ANTENNADLK-67
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 33, 34 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key unit and overhead console area antenna.
3.CHECK INSIDE KEY ANTENNA POWER SUPPLY SINGAL
1. Replace overhead console area antenna. (New antenna or other antenna)
2. Connect Intelligent Key unit connector.
3. Check signal between Intelligent Key unit connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace overhead console area antenna.
NO >> Replace Intelligent Key unit. Refer to SEC-120, "
Removal and Installation".
Intelligent Key
unit connectorTe r m i n a l sOverhead console
area antenna con-
nector Terminals Continuity
A: M70 33
B: R210 1
Ye s
34 2
Item Connector TerminalsContinuity
Intelligent Key unit A: M70 33
Ground No
34
ALKIA0590ZZ
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 33 Ground Ignition
switch is
pushed.
ALKIA0589ZZ
PIIB7441E
Revision: April 20092010 QX56