turn signal INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 1156 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U1514 STRG SEN CAN 3DAS-191
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006228163
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is det](/img/42/57033/w960_57033-1155.png "INFINITI QX56 2011 Factory Service Manual
DAS
U1514 STRG SEN CAN 3DAS-191
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006228163
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is det")
DAS
U1514 STRG SEN CAN 3DAS-191
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1514 STRG SEN CAN 3
DTC LogicINFOID:0000000006228163
DTC DETECTION LOGIC
NOTE:
If DTC “U1514” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1514” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1514” detected as the current malfunction?
YES >> Refer to DAS-191, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228164
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U1514” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1514 (165) STRG SEN CAN CIRC 3 ADAS control unit detects an error signal that is
received from steering angle sensor via CAN
communication
Steering angle sensor
Revision: 2010 May2011 QX56
Page 1157 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-192
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1515 ICC SENSOR CAN 3
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006228165
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is detected along with DTC “U
1000](/img/42/57033/w960_57033-1156.png "INFINITI QX56 2011 Factory Service Manual
DAS-192
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1515 ICC SENSOR CAN 3
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006228165
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is detected along with DTC “U
1000")
DAS-192
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1515 ICC SENSOR CAN 3
U1515 ICC SENSOR CAN 3
DTC LogicINFOID:0000000006228165
DTC DETECTION LOGIC
NOTE:
If DTC “U1515” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U1515” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1515” detected as the current malfunction?
YES >> Refer to DAS-192, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228166
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U1515” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ICC SENSOR SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “S elf Diagnostic Result” of “LASER”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-55, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1515 (165) ICC SENSOR CAN
CIRC 3 ADAS control unit detects an error signal that is
received from ICC sensor via CAN communi-
cation
ICC sensor
Revision: 2010 May2011 QX56
Page 1158 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3DAS-193
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006228167
DTC DETECTION L](/img/42/57033/w960_57033-1157.png "INFINITI QX56 2011 Factory Service Manual
DAS
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3DAS-193
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006228167
DTC DETECTION L")
DAS
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3DAS-193
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
U1517 ACCELERATOR PEDAL ACTUATOR CAN 3
DTC LogicINFOID:0000000006228167
DTC DETECTION LOGIC
NOTE:
If DTC “U1517” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “U1517” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1517” detected as the current malfunction?
YES >> Refer to DAS-193, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228168
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U1517” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK ACCELERATOR PEDAL ACTU ATOR SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ACCELE PEDAL ACT”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-108, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1517 (167) APA CAN CIRC 3 ADAS control unit detects an error signal that is
received from accelerator pedal actuator via
CAN communication
Accelerator pedal actuator
Revision: 2010 May2011 QX56
Page 1159 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-194
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1520 4WD CAN 3
U1520 4WD CAN 3
DTC LogicINFOID:0000000006228169
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected along with DTC “U
1000”, first dia](/img/42/57033/w960_57033-1158.png "INFINITI QX56 2011 Factory Service Manual
DAS-194
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1520 4WD CAN 3
U1520 4WD CAN 3
DTC LogicINFOID:0000000006228169
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected along with DTC “U
1000”, first dia")
DAS-194
< DTC/CIRCUIT DIAGNOSIS >[DCA]
U1520 4WD CAN 3
U1520 4WD CAN 3
DTC LogicINFOID:0000000006228169
DTC DETECTION LOGIC
NOTE:
If DTC “U1520” is detected along with DTC “U
1000”, first diagnose the DTC “U1000”. Refer to DAS-182,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the DCA system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “U1520” is detected as the current ma lfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1520” detected as the current malfunction?
YES >> Refer to DAS-194, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006228170
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected ot her than “U1520” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communication system inspecti on. Repair or replace the malfunctioning parts.
Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK TRANSFER CONTROL UNI T SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ALL MODE AWD/4WD”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DLN-29, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
U1520 (176) 4WD CAN CIRC 3 ADAS control unit detects an error signal that is
received from transfer control unit via CAN
communication
Transfer control unit
Revision: 2010 May2011 QX56
Page 1160 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
POWER SUPPLY AND GROUND CIRCUITDAS-195
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOI](/img/42/57033/w960_57033-1159.png "INFINITI QX56 2011 Factory Service Manual
DAS
POWER SUPPLY AND GROUND CIRCUITDAS-195
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOI")
DAS
POWER SUPPLY AND GROUND CIRCUITDAS-195
< DTC/CIRCUIT DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
POWER SUPPLY AND GROUND CIRCUIT
ADAS CONTROL UNIT
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006223648
1.CHECK ADAS CONTROL UNIT POWER SUPPLY CIRCUIT
Check voltage between ADAS contro l unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the ADAS control unit power supply circuit.
2.CHECK ADAS CONTROL UNIT GROUND CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect the ADAS control unit connector.
3. Check for continuity between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair the ADAS control unit ground circuit.
ACCELERATOR PEDAL ACTUATOR
ACCELERATOR PEDAL ACTUATOR : Diagnosis ProcedureINFOID:0000000006223649
1.CHECK FUSES
Check if any of the following fuses are blown:
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK ACCELERATOR PEDAL ACTUATOR POWER SUPPLY CIRCUIT
Check voltage between accelerator pedal actuator harness connector and ground.
Te r m i n a l Condition
Vo l ta g e
(Approx.)
(+) (–)
ADAS control unit
GroundIgnition
switch
Connector Terminal
B61 16 OFF 0 V
ON Battery volt-
age
ADAS control unit
GroundContinuity
Connector Terminal
B61 6 Existed
Signal name Fuse No.
Battery power supply 33
Revision: 2010 May2011 QX56
Page 1166 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
DCA SYSTEM NOT ACTIVATED (SWITCH IS ON)DAS-201
< SYMPTOM DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
DCA SYSTEM NOT ACTIVA TED (SWITCH IS ON)
DescriptionINFOID:0000000006223655
The dynamic dr](/img/42/57033/w960_57033-1165.png "INFINITI QX56 2011 Factory Service Manual
DAS
DCA SYSTEM NOT ACTIVATED (SWITCH IS ON)DAS-201
< SYMPTOM DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
DCA SYSTEM NOT ACTIVA TED (SWITCH IS ON)
DescriptionINFOID:0000000006223655
The dynamic dr")
DAS
DCA SYSTEM NOT ACTIVATED (SWITCH IS ON)DAS-201
< SYMPTOM DIAGNOSIS > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
DCA SYSTEM NOT ACTIVA TED (SWITCH IS ON)
DescriptionINFOID:0000000006223655
The dynamic driver assistance switch can be tu rned ON/OFF, but the DCA system does not operate.
NOTE:
Never start the operation under the following conditions. No operation condition
When the brake pedal depressed
When the ICC system is set
When the system judges that the vehicle co mes to a standstill by the system control
When the vehicle ahead is not detected Operation cancellation condition
When the dynamic driver assistance switch is turned to OFF
When the system malfunction occurs
When ABS or VDC (including the TCS) operates
When the VDC is turned OFF
When driving into a strong light (i.e., sunlight)
When the ICC sensor body window is dirty and the measurement of the distance between the vehicles
becomes difficult
When ABS warning lamp is ON
When the SNOW mode switch is turned ON
When the 4WD shift switch is not AUTO position
Diagnosis ProcedureINFOID:0000000006223656
1.CHECK CAUSE OF AUTOMATIC CANCELLATION
Check if there is any cancellation cause in the “CAUSE OF AUTO-CANCEL” on “WORK SUPPORT” of “ICC/
ADAS” with CONSULT-III.
Is it displayed?
Not displayed>>GO TO 2.
“OPE SW VOLT CIRC”>>Refer to DAS-138, "
DTC Logic".
“VHCL SPD UNMATCH”>>Refer to DAS-131, "
DTC Logic".
“IGN LOW VOLT”>>Refer to DAS-130, "
DTC Logic".
“CAN COMM ERROR”>>Refer to DAS-182, "
ADAS CONTROL UNIT : DTC Logic".
“ICC SENSOR CAN COMM ERR”>>Refer to DAS-177, "
DTC Logic".
“ABS/TCS/VDC CIRC”>>Refer to DAS-133, "
DTC Logic".
“APA HI TEMP”>>Refer to DAS-170, "
DTC Logic".
“ECD CIRCUIT”>>Refer to DAS-156, "
DTC Logic".
2.PERFORM ALL OF THE SELF-DIAGNOSIS
1. Perform “All DTC Reading”.
2. Check if any DTC is detected in self-d iagnosis results of “ICC/ADAS”. Refer to DAS-100, "
DTC Index".
Is any DTC detected?
YES >> GO TO 3.
NO >> GO TO 4.
3.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts i dentified by the self-diagnosis result.
>> GO TO 6.
4.CHECK EACH SWITCH AND VEHICLE SPEED SIGNAL
1. Start the engine.
2. Check that the following items operate norma lly in “DATA MONITOR” of “ICC/ADAS”.
- “VHCL SPEED SE”
- “BRAKE SW”
- “DYNA ASIST SW”
Is there a malfunctioning item?
Revision: 2010 May2011 QX56
Page 1181 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-216
< SYSTEM DESCRIPTION >[FCW]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006223671
Component DescriptionINFOID:0000000006223672
1. Information disp](/img/42/57033/w960_57033-1180.png "INFINITI QX56 2011 Factory Service Manual
DAS-216
< SYSTEM DESCRIPTION >[FCW]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006223671
Component DescriptionINFOID:0000000006223672
1. Information disp")
DAS-216
< SYSTEM DESCRIPTION >[FCW]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006223671
Component DescriptionINFOID:0000000006223672
1. Information display, IBA OFF indica-
tor lamp, buzzer
(On the combination meter) 2. ABS actuator and electric unit (con-
trol unit)
Refer to BRC-10, "
Component Parts
Location"
3. ICC sensor
Refer to CCS-9, "
Component Parts
Location"
4. Warning systems switch 5. Warning systems ON indicator 6. ADAS control unit
Refer to DAS-13, "
Component Parts
Location"
A. Instrument lower panel (LH)
JSOIA0366ZZ
Component Description
ADAS control unit ADAS control unit turns ON warning systems ON indicator
ADAS control unit transmits a buzzer output signal to combination meter via CAN commu-
nication
ICC sensor ICC sensor detects light reflected from a vehicle ahead by irradiating laser forward and cal-
culates a distance from the vehicle ahead and a relative speed, based on the detected sig-
nal
ICC sensor transmits the presence/absence of a vehicle ahead and a distance from the ve- hicle ahead to the ADAS control unit via CAN communication
ABS actuator and electric unit
(control unit) ABS actuator and electric unit (c
ontrol unit) transmits the vehicle speed signal (wheel speed),
to ADAS control unit via CAN communication
Warning systems switch Inputs the warning systems switch signal to ADAS control unit.
Revision: 2010 May2011 QX56
Page 1182 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
COMPONENT PARTSDAS-217
< SYSTEM DESCRIPTION > [FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
Warning systems ON indicator
(In the warning systems switch) Turns warning systems ON indicator ON/OFF according](/img/42/57033/w960_57033-1181.png "INFINITI QX56 2011 Factory Service Manual
DAS
COMPONENT PARTSDAS-217
< SYSTEM DESCRIPTION > [FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
Warning systems ON indicator
(In the warning systems switch) Turns warning systems ON indicator ON/OFF according")
DAS
COMPONENT PARTSDAS-217
< SYSTEM DESCRIPTION > [FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
Warning systems ON indicator
(In the warning systems switch) Turns warning systems ON indicator ON/OFF according to the signals from the ADAS control
unit
Warning systems ON indicator turns on, according to an warning systems ON indicator signal.
Combination meter Performs the following operations using the signals received from the ADAS control unit via
the CAN communication
Blinks the vehicle ahead detection indicator according to a meter display signal
Illuminates the IBA OFF indicator lamp using the IBA OFF indicator lamp signal
Operates the buzzer (ICC warning chime) using the buzzer output signal
Component Description
Revision: 2010 May2011 QX56
Page 1183 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS-218
< SYSTEM DESCRIPTION >[FCW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006223673
SYSTEM DIAGRAM
ADAS CONTROL UNIT INPU
T/OUTPUT SIGNAL ITEM
Input Signal Item
Output Signal Item
DESCRIPTION](/img/42/57033/w960_57033-1182.png "INFINITI QX56 2011 Factory Service Manual
DAS-218
< SYSTEM DESCRIPTION >[FCW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006223673
SYSTEM DIAGRAM
ADAS CONTROL UNIT INPU
T/OUTPUT SIGNAL ITEM
Input Signal Item
Output Signal Item
DESCRIPTION")
DAS-218
< SYSTEM DESCRIPTION >[FCW]
SYSTEM
SYSTEM
System DescriptionINFOID:0000000006223673
SYSTEM DIAGRAM
ADAS CONTROL UNIT INPU
T/OUTPUT SIGNAL ITEM
Input Signal Item
Output Signal Item
DESCRIPTION
The Forward Collision Warning (FCW) system will warn the driver by a warning lamp (vehicle ahead detec-
tion indicator) and chime when own vehicle is getting close to the vehicle ahead in the traveling lane.
JSOIA0279GB
Transmit unit Signal name Description
ABS actuator
and electric unit
(control unit) CAN com-
munica-
tion
Vehicle speed signal (ABS) Receives wheel speeds of four wheels
ICC sensor ITS com-
munica-
tion
ICC sensor signal
Receives detection results, such as the presence or ab-
sence of a leading vehicle and distance from the vehicle
Warning sys-
tems switch Warning systems switch signal Receives an ON/OFF state of the warning systems
switch
Reception unit Signal name Description
Combination
meter CAN commu-
nicationMeter display
signal
Vehicle ahead detec-
tion indicator signal Transmits a signal to display a state of the system on
the information display
IBA OFF indicator lamp signal Transmits a signal to turn ON the IBA OFF indicator
lamp
Transmits an ON/OFF state of the intelligent brake assist
Buzzer output signal Transmits a buzzer output signal to activate the buzz-
er
ICC sensor ITS commu-
nication
Vehicle speed signal Transmits a vehicle speed calculated by the ADAS
control unit
Warning sys-
tems ON indi-
cator Warning systems ON indicator signal Turns ON the warning systems ON indicator
Revision: 2010 May2011 QX56
Page 1184 of 5598
![INFINITI QX56 2011 Factory Service Manual
DAS
SYSTEM
DAS-219
< SYSTEM DESCRIPTION >[FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
The FCW system will function when own vehicle is dr iven at speeds of approximately 15 km/h (10 MPH) and
above.
NOTE:
Th](/img/42/57033/w960_57033-1183.png "INFINITI QX56 2011 Factory Service Manual
DAS
SYSTEM
DAS-219
< SYSTEM DESCRIPTION >[FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
The FCW system will function when own vehicle is dr iven at speeds of approximately 15 km/h (10 MPH) and
above.
NOTE:
Th")
DAS
SYSTEM
DAS-219
< SYSTEM DESCRIPTION >[FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
The FCW system will function when own vehicle is dr iven at speeds of approximately 15 km/h (10 MPH) and
above.
NOTE:
The FCW system shares the di agnosis function with ICC system.
FUNCTION DESCRIPTION
The distance from the vehicle ahead and a relative speed are calculated by using the ICC sensor and an ICC
sensor signal is transmitted to t he ADAS control unit via ITS communi cation. When judging the necessity of
warning according to the received vehicle ahead detection signal, the ADAS control unit transmits a buzzer
output signal and meter display signal to the combination meter via CAN communication.
FCW Operating Condition
Warning systems ON indicator: ON
Vehicle speed: Approximately 15 km/h (10 MPH) and above.
Fail-safe Indication
FCW INITIAL STATE CHANGE
CAUTION:
Never change FCW initial state “ON” ⇒ “OFF” without the con sent of the customer.
FCW initial state can be changed.
FCW initial ON* - FCW function is automatically turned ON, when the ignition switch OFF ⇒ ON.
FCW initial OFF - FCW function is still OFF when the ignition switch OFF ⇒ ON.
*: Factory setting
How to change FCW/LDW/BSW initial state1. Turn ignition switch ON.
2. Warning systems switch is OFF.
3. Push and hold warning systems switch for more than 4 seconds.
4. Buzzer sounds and blinking of the warning systems ON indicator informs that the FCW/LDW/BSW initial
state change is completed.
Fail-safe (ADAS Control Unit)INFOID:0000000006223674
If a malfunction occurs in each s ystem, ADAS control unit cancels eac h control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
Vehicle condition Indication on the combination meter
When the FCW system malfunctions
When the sensor window is dirty
When driving into a strong light (i.e. sunlight)
NOTE:
Check that the IBA system is not OFF. The indicator lamp is shared
with IBA system.
JPOIA0179ZZ
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warning lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
toneICC system warning lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
tone
IBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
tone
IBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
toneICC system warning lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Revision: 2010 May2011 QX56