warning INFINITI QX56 2011 Factory Service Manual

DAS
SIDE RADAR RHDAS-447
< ECU DIAGNOSIS INFORMATION > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
If a malfunction occurs in the side radar, ADAS control unit cancels the control. Then the BSW warning lamp in
the combination meter illuminates.
TEMPORARY DISABLED STATUS AT BLOCKAGE
When the side radar is blocked, the operation is tempor arily cancelled. Then BSW warning lamp in combina-
tion meter blinks. Also, under the following conditions, the operation may be temporarily cancelled.
 The side radar may be blocked by temporary ambient c onditions such as splashing water, mist or fog.
 The blocked condition may also be caused by objects such as ice, frost or dirt obstructing the side radar.
DTC Inspection Priority ChartINFOID:0000000006223871
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000006223872
× : Applicable
Priority Detected items (DTC)
1  U1000: CAN COMM CIRCUIT
 U1010: CONTROL UNIT (CAN)
2  U0104: ADAS CAN CIR 1
 U0405: ADAS CAN CIR 2
3 C1B50: SIDE RDR MALFUNCTION
4  C1B51: BSW/BSI IND SHORT CIR
 C1B52: BSW/BSI IND OPEN CIR
 C1B55: RADAR BLOCKAGE
DTC BSW warning lamp Fail-safe Reference page
C1B50 SIDE RDR MALFUNCTION ON ×DAS-478
C1B51 BSW/BSI IND SHORT CIR ON ×DAS-479
C1B52 BSW/BSI IND OPEN CIR ON ×DAS-480
C1B55 RADAR BLOCKAGE Blink ×DAS-484
U1000 CAN COMM CIRCUIT ON ×DAS-486
U1010 CONTROL UNIT (CAN) ON ×DAS-488
U0104 ADAS CAN CIR1 ON ×DAS-490
U0405 ADAS CAN CIR2 ON ×DAS-495
Revision: 2010 May2011 QX56

DAS
ADDITIONAL SERVICE WHEN REPLACING SIDE RADARDAS-467
< BASIC INSPECTION > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
ADDITIONAL SERVICE WHEN REPLACING SIDE RADAR
DescriptionINFOID:0000000006223876
 After replacing the side radar, activate (normal usage mode) it in work support mode with CONSLUT-III.
 If both side radars are not brought into the norma l usage mode, BSW does not operate and the BSW warn-
ing lamp blinks.
Work ProcedureINFOID:0000000006223877
1.ACTIVATE OPERATION
1. Select “WORK SUPPORT” item “ACTIVATE OPERAT ION” of SIDE RADAR (LEFT, RIGHT) with CON-
SULT-III.
2. Select “Activate”.
3. Check that “DATA MONITOR” item “ACTIVATE OPE” is changed to “On”.
4. Turn ignition switch OFF.
>> GO TO 2.
2.PERFORM SELF-DIAGNOSIS
1. Turn ignition switch ON.
2. Perform the self-diagnosis of side radar with CONSULT-III. Check if any DTC is detected.
Is any DTC detected?
YES >> Perform the trouble diagnosis for the detected DTC. Refer to DAS-447, "DTC Index".
NO >> GO TO 3.
3.BSW WARNING LAMP CHECK
1. Perform the BSW system action test. Refer to DAS-468, "
Description".
2. Check that BSW system operates normally.
>> WORK END
Revision: 2010 May2011 QX56

DAS-468
< BASIC INSPECTION >[BSW]
ACTION TEST
ACTION TEST
DescriptionINFOID:0000000006223878
Always perform the BSW system action test to check
that the system operates normally after replacing the
side radar LH/RH, or repairing any BSW system malfunction.
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
Fully understand the following it ems well before the road test;
 Precautions: Refer to DAS-407, "
Precaution for BSW System Service".
 System description: Refer to DAS-410, "
System Description".
 Normal operating condition: Refer to DAS-522, "
Description".
Work ProcedureINFOID:0000000006223879
WARNING:
Be careful of traffic conditions and safety ar ound the vehicle when performing road test.
CAUTION:
Fully understand the following it ems well before the road test;
 Precautions: Refer to DAS-407, "
Precaution for BSW System Service".
 System description: Refer to DAS-410, "
System Description".
 Normal operating condition: Refer to DAS-522, "
Description".
1.BSW SYSTEM ACTION TEST
1. Drive the vehicle.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check BSW operation according to the following table.
Vehicle condition/ Driver's operation Action
Warning
systems ON indicator Vehicle speed
(Approx.)
[km/h (MPH)] Turn signal
condition Status of ve-
hicle detec- tion within detection
area Indication on the
BSW indicator Buzzer
OFF — — — OFF OFF
ON Less than ap-
prox.
29 (18) —— OFF OFF
Approx. 32 (20)
or more —
Ve h i c l e i s
absent OFF OFF
OFF Ve h i c l e i s
detected ON OFF
ON
(vehicle de-
tected direc- tion) Before turn
signal oper-
ates
Ve h i c l e i s detected Blink Short continuous beep
Ve h i c l e i s
detected af- ter turn sig-
nal operates Blink
OFF
JSOIA0251GBJSOIA0252GB
JSOIA0251GB
Revision: 2010 May2011 QX56

DAS-472
< DTC/CIRCUIT DIAGNOSIS >[BSW]
C1A03 VEHICLE SPEED SENSOR
C1A03 VEHICLE SPEED SENSOR
DTC LogicINFOID:0000000006223884
DTC DETECTION LOGIC
NOTE:
If DTC “C1A03” is detected along
with DTC “U1000” or “C1A04”, first diagnose the DTC “U1000” or “C1A04”.
 Refer to DAS-486, "
ADAS CONTROL UNIT : DTC Logic" for DTC “U1000”.
 Refer to DAS-348, "
DTC Logic" for DTC “C1A04”.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the BSW system ON.
3. Drive the vehicle at 30 km/h (19 MPH) or more. CAUTION:
Always drive safely.
4. Stop the vehicle.
5. Perform “All DTC Reading” with CONSULT-III.
6. Check if the “C1A03” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A03” detected as the current malfunction?
YES-1 (BSW warning lamp: ON)>>Refer to DAS-472, "Diagnosis Procedure".
YES-2 (BSW warning lamp: OFF)>>Refer to CCS-87, "
Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006223885
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “C1A04” or “U1000” is detected other than “C1A03” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-440, "
DTC Index".
NO >> GO TO 2.
2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board
display) Trouble diagnosis
name DTC detecting condition Possible causes
C1A03 (3) VHCL SPEED SE
CIRC If the vehicle speed signal (wheel speed) from
ABS actuator and electric
unit (control unit) re-
ceived by the ADAS control unit via CAN com-
munication, are inconsistent  Wheel speed sensor
 ABS actuator and electric unit (control
unit)
 ADAS control unit
Revision: 2010 May2011 QX56

DAS-484
< DTC/CIRCUIT DIAGNOSIS >[BSW]
C1B55 RADAR BLOCKAGE
C1B55 RADAR BLOCKAGE
DTC LogicINFOID:0000000006223903
DTC DETECTION LOGIC
NOTE:
DTC “C1B55” may be detected under the following conditions except for possible cause. (Explain to the customer about the differ
ence
between the contamination detection function and the indication when the malfunction is detected and tell them “This is not mal func-
tion”.)
 The side radar may be blocked by temporary ambient conditions such as splashing water, mist or fog.
 The blocked condition may also be caused by objects such as ice, frost or dirt obstructing the side radar.
 Due to the nature of radar technology it is possible to get a blockage warning and not actually be blocked. This is rare and i s known as
a false blockage warning. A false blocked condition either self-clears or clears after an ignition cycle.
Diagnosis ProcedureINFOID:0000000006223904
1.CHECK THE REAR BUMPER
Check rear bumper near the side radar contaminated with foreign materials.
>> GO TO 2.
2.CHECK THE SIDE RADAR
Check side radar and the side radar outskirts contaminated with foreign materials.
>> GO TO 3.
3.CHECK THE SIDE RADAR INSTALL CONDITION
Check side radar installation condition (installati on position, properly tightened, a bent bracket).
>> GO TO 4.
4.INTERVIEW
1. Ask if there is stain or foreign materials.
2. Ask if there is any temporary ambient condi tion such as splashing water, mist or fog.
3. Ask if there is any object such as ice, frost or dirt obstructing the side radar.
Is any of above conditions seen?
YES >> Explain to the customer about the differ ence between the blockage detection function and the
indication when the malfunction is detected and tell them “This is not malfunction”.
NO >> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
C1B55 RADAR BLOCKAGE Sid e radar is blocked. Stain or foreign materials is deposit-
ed.
Revision: 2010 May2011 QX56

DAS
WARNING SYSTEMS SWITCH CIRCUITDAS-515
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
WARNING SYSTEMS SWITCH CIRCUIT
Component Function CheckINFOID:0000000006223971
1.CHECK WARNING SYSTEMS SWITCH INPUT SIGNAL
1. Turn the ignition switch ON.
2. Select the DATA MONITOR item “WARN SYS SW” of “ICC/ADAS” with CONSULT-III.
3. With operating the warning systems switch, check the monitor status.
Is the inspection result normal?
YES >> Warning systems switch circuit is normal.
NO >> Refer to DAS-389, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006223972
1.CHECK WARNING SYSTEMS SWITCH SIGNAL INPUT
1. Turn the ignition switch ON.
2. Check voltage between ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> GO TO 2.
2.CHECK WARNING SYSTEMS SWITCH
1. Turn ignition switch OFF.
2. Remove warning systems switch.
3. Check warning systems switch. Refer to DAS-390, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the warning systems switch. Refer to DAS-404, "
Removal and Installation".
3.CHECK WARNING SYSTEMS SWITCH GROUND CIRCUIT
Check continuity between twin switch harness connector terminal and the ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair harness or connector.
4.CHECK WARNING SYSTEM S SWITCH SIGNAL INPUT CIRCUIT FOR OPEN
1. Disconnect the ADAS control unit connector.
Monitor item Condition Monitor status
WARN SYS
SW Warning systems switch is pressed On
Warning systems switch is not pressed OFF
Te r m i n a l s
Condition
Vo l ta g e
(Approx.)
(+) (
−)
ADAS control unit
GroundWarning
systems switch
Connector Terminal
B61 1 Pressed 0 V
Released 12 V
Twin switch GroundContinuity
Connector Terminal
M127 3 Existed
Revision: 2010 May2011 QX56

DAS-516
< DTC/CIRCUIT DIAGNOSIS >[BSW]
WARNING SYSTEMS SWITCH CIRCUIT
2. Check continuity between the ADAS control unit harness connector and twin switch harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair the harnesses or connectors.
5.CHECK WARNING SYSTEMS SWITCH SI
GNAL INPUT CIRCUIT FOR SHORT
Check continuity between the ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> Repair the harnesses or connectors.
Component InspectionINFOID:0000000006223973
1.CHECK WARNING SYSTEMS SWITCH
Check continuity of warning systems switch.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace warning systems switch.
ADAS control unit Twin switch Continuity
Connector Terminal Connector Terminal
B61 1 M127 2 Existed
ADAS control unit GroundContinuity
Connector Terminal
B61 1 Not existed
Terminal Condition Continuity
23 When warning systems switch is pressed Existed
When warning systems switch is released Not existed
Revision: 2010 May2011 QX56

DAS
WARNING SYSTEMS ON INDICATOR CIRCUITDAS-517
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
WARNING SYSTEMS ON INDICATOR CIRCUIT
Component Function CheckINFOID:0000000006223974
1.CHECK WARNING SYSTEMS ON INDICATOR
1. Turn the ignition switch ON.
2. Select the active test item “WARNING SY STEM IND” of “ICC/ADAS” with CONSULT-III.
3. With operating the test item, check the operation.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to DAS-517, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006223975
1.CHECK WARNING ON INDICATOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect twin switch connector.
3. Turn ignition switch ON.
4. Check voltage between twin switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the warning systems ON indicator power supply circuit.
2.CHECK WARNING SYSTEMS ON INDICATOR SIGNAL FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect the ADAS control unit harness connector.
3. Check continuity between the ADAS control uni t harness connector and twin switch harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair the harnesses or connectors.
3.CHECK WARNING SYSTEMS ON INDI CATOR SIGNAL CIRCUIT FOR SHORT
Check continuity between the ADAS control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4. On : Warning systems ON indicator illuminates
Off : Warning systems ON in
dicator is turned OFF
Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (
−)
Twin switch Ground
Connector Terminal
M127 8 Battery voltage
ADAS control unit Twin switch Continuity
Connector Terminal Connector Terminal
B61 4 M127 9 Existed
ADAS control unit
GroundContinuity
Connector Terminal
B61 4 Not existed
Revision: 2010 May2011 QX56

DAS-518
< DTC/CIRCUIT DIAGNOSIS >[BSW]
WARNING SYSTEMS ON
INDICATOR CIRCUIT
NO >> Repair the harnesses or connectors.
4.CHECK WARNING SYSTEMS ON INDICATOR
Check the warning systems ON indicator. Refer to DAS-518, "
Component Inspection".
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> Replace warning systems switch. DAS-404, "
Removal and Installation".
Component InspectionINFOID:0000000006223976
1.CHECK WARNING SYSTEMS ON INDICATOR
Apply battery voltage to warning systems switch termi nals 8 and 9, and then check if the warning systems ON
indicator illuminates.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace the warning systems switch. Refer to DAS-404, "
Removal and Installation".
Te r m i n a l s
ConditionDriver warning
systems ON in-
dicator
(+) (-)
89 When the battery voltage is applied On
When the battery voltage is not applied Off
Revision: 2010 May2011 QX56

DAS
WARNING BUZZER CIRCUITDAS-519
< DTC/CIRCUIT DIAGNOSIS > [BSW]
C
D
E
F
G H
I
J
K L
M B
N P A
WARNING BUZZER CIRCUIT
Component Function CheckINFOID:0000000006223977
1.CHECK WARNING BUZZER
1. Turn the ignition switch ON.
2. Select the active test item “LDP BU ZZER” of “ICC/ADAS” with CONSULT-III.
3. With operating the test item, check the operation.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to DAS-393, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006223978
1.CHECK WARNING BUZZER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the warning buzzer connector.
3. Turn ignition switch ON.
4. Check voltage between the warning buzzer harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the warning buzzer power supply circuit.
2.CHECK WARNING BUZZER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between the warning buzzer harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair the harnesses or connectors.
3.CHECK WARNING BUZZER SIGNAL CIRCUIT FOR OPEN
1. Disconnect the ADAS control unit connector.
2. Check continuity between the ADAS control uni t harness connector and warning buzzer harness connec-
tor.
Is the inspection result normal?
On : Warning buzzer is activated.
Off : Warning buzzer is not activated.
Te r m i n a l s Vo l ta g e
(Approx.)
(+) (
−)
Warning buzzer Ground
Connector Terminal
M94 1 Battery voltage
Warning buzzer GroundContinuity
Connector Terminal
M94 3 Existed
ADAS control unit Warning buzzer Continuity
Connector Terminal Connector Terminal
B61 12 M94 2 Existed
Revision: 2010 May2011 QX56