BATTERY CONNECTORS INFINITI QX56 2011 Factory Service Manual

P0775 PRESSURE CONTROL SOLENOID BTM-133
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P0775 PRESSURE CONTROL SOLENOID B
DTC LogicINFOID:0000000006226845
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P0775” detected?
YES >> Go to TM-133, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226846
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0775 Pressure Control Solenoid B The input clutch solenoid valve
monitor value is 0.4 A or less
when the input clutch solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Input clutch solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 1st
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-136
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P0795 PRESSURE CONTROL SOLENOID C
P0795 PRESSURE CONTROL SOLENOID C
DTC LogicINFOID:0000000006226850
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “G EAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P0795” detected?
YES >> Go to TM-136, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226851
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P0795 Pressure Control Solenoid C The front brake solenoid valve
monitor value is 0.4 A or less
when the front brake solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Front brake solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 7th
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-144
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P1815 M-MODE SWITCH
P1815 M-MODE SWITCH
DTC LogicINFOID:0000000006226864
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select “SLCT LVR POSI” and “MANU MODE SW ” in “Data Monitor” in “TRANSMISSION”.
3. Maintain the following each conditions more than 2 seconds.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
Is
“P1815” detected?
YES >> Go to TM-144, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226865
1.CHECK MANUAL MODE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect A/T shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between A/T shift selector vehicle side harness connector terminals.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK MANUAL MODE SWITCH
DTC Trouble diagnosis name DTC is detected if... Possible cause
P1815 Manual Mode Switch Circuit TCM monitors manual mode,
non manual mode, up or down
switch signal, and detects as ir-
regular when impossible input
pattern occurs 2 second or
more. Harness or connectors
(These switches circuit is
open or shorted.)
 Manual mode switch
SLCT LVR POSI : D
MANU MODE SW : ON
A/T shift selector vehicle side harness connector
Voltage (Approx.)
Connector Te r m i n a l
+ −
M57 1
4 Battery voltage
2
3
5
Revision: 2010 May2011 QX56

P2713 PRESSURE CONTROL SOLENOID DTM-147
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P2713 PRESSURE CONTROL SOLENOID D
DTC LogicINFOID:0000000006226867
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive the vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2713” detected?
YES >> Go to TM-147, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226868
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2713 Pressure Control Solenoid D The high and low reverse clutch
solenoid valve monitor value is
0.4 A or less when the high and
low reverse clutch solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 High and low reverse clutch solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 3rd
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-148
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P2722 PRESSURE CONTROL SOLENOID E
P2722 PRESSURE CONTROL SOLENOID E
DTC LogicINFOID:0000000006226869
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “G EAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2722” detected?
YES >> Go to TM-148, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226870
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2722 Pressure Control Solenoid E The low brake solenoid valve
monitor value is 0.4 A or less
when the low brake solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Low brake solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 1st
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

P2731 PRESSURE CONTROL SOLENOID FTM-149
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P2731 PRESSURE CONTROL SOLENOID F
DTC LogicINFOID:0000000006226871
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2731” detected?
YES >> Go to TM-149, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226872
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2731 Pressure Control Solenoid F The 2346 brake solenoid valve
monitor value is 0.4 A or less
when the 2346 brake solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 2346 brake solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 2nd
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-150
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P2807 PRESSURE CO
NTROL SOLENOID G
P2807 PRESSURE CONTROL SOLENOID G
DTC LogicINFOID:0000000006226873
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “G EAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2807” detected?
YES >> Go to TM-150, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226874
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected is... Possible cause
P2807 Pressure Control Solenoid G The direct clutch solenoid valve
monitor value is 0.4 A or less
when the direct clutch solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Direct clutch solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 1st
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TRANSMISSION ASSEMBLYTM-205
< UNIT REMOVAL AND INSTALLATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
2WD
2WD : Exploded ViewINFOID:0000000006233263
2WD : Removal and InstallationINFOID:0000000006233264
REMOVAL
CAUTION:
 When removing the A/T assembly from engine, fi rst remove the crankshaft position sensor (POS)
from the A/T assembly.
 Be careful not to damage sensor edge.
1. Shift the selector lever to “P” position, and release the parking brake.
2. Disconnect the battery cabl e from the negative terminal.
3. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug and
overflow plug.
4. Remove rear engine mounting cross member.
5. Remove engine mounting insulator (rear).
6. Remove control cable from A/T assembly. Refer to TM-178, "
Removal and Installation".
7. Disconnect heated oxygen sensor 2 connectors (bank 1 and bank 2). Refer to EX-5, "
Exploded View".
1. A/T assembly 2. Front suspension rear cross mem-
ber3. Rear engine mounting cross
member
4. Engine mounting insulator (rear)
A. Tightening must be done following the installation procedure. Refer to TM-205, "
2WD : Removal and Installation".
Refer to GI-4, "
Components" for symbols in the figure.
JSDIA1856GB
Revision: 2010 May2011 QX56

TM-208
< UNIT REMOVAL AND INSTALLATION >[7AT: RE7R01B]
TRANSMISSION ASSEMBLY
4WD : Exploded View
INFOID:0000000006226910
4WD : Removal and InstallationINFOID:0000000006226911
REMOVAL
CAUTION:
 When removing the A/T assembly from engine, fi rst remove the crankshaft position sensor (POS)
from the A/T assembly.
 Be careful not to damage sensor edge.
1. Shift the selector lever to “P” pos ition, and release the parking brake.
2. Disconnect the battery cable from the negative terminal.
3. Remove control cable from A/T assembly. Refer to TM-178, "
Removal and Installation".
4. Disconnect heated oxygen sensor 2 connectors (bank 1 and bank 2). Refer to EX-5, "
Exploded View".
5. Remove exhaust front tube (RH and LH) and main muffler. Refer to EX-5, "
Exploded View".
6. Support A/T assembly with a transmission jack. CAUTION:
When setting the transmission jack, be careful not to allow it to collide against the drain plug and
overflow plug.
7. Remove rear engine mounting cross member and engine mounting insulator (rear).
8. Separate propeller shaft assembly (front). Refer to DLN-129, "
Removal and Installation".
9. Separate propeller shaft assembly (rear). Refer to DLN-137, "
Removal and Installation".
10. Remove front under cover with a power tool. Refer to EXT-25, "
Removal and Installation".
11. Remove front suspension rear cross member.
1. A/T assembly 2. Front suspension rear cross mem- ber3. Rear engine mounting cross
member
4. Engine mounting insulator (rear)
A. Tightening must be done following the installation procedure. Refer to TM-208, "
4WD : Removal and Installation".
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA1156GB
Revision: 2010 May2011 QX56

PRECAUTIONSVTL-3
< PRECAUTION >
C
DE
F
G H
J
K L
M A
B
VTL
N
O P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006376373
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoper ative, which could increase the risk of personal injury or death in
the event of a collision that would result in air ba g inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintentional act ivation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipm ent on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wh eel Rotation after Battery Disconnect
INFOID:0000000006376453
NOTE:
 Before removing and installing any control units, first tu rn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnos is according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the batte ry disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position. (At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock wil l remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
Revision: 2010 May2011 QX56