ECU INFINITI QX56 2011 Factory Service Manual

PCS-2
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect ..................................
33
SYSTEM DESCRIPTION ............................35
COMPONENT PARTS .................................... ...35
Component Parts Location .................................. ...35
Component Description .........................................35
BCM ........................................................................35
Ignition Relay ..........................................................35
Accessory Relay .....................................................36
Blower Relay ..........................................................36
Push-Button Ignition Switch ....................................36
SYSTEM .......................................................... ...37
POWER DISTRIBUTION SYST EM ........................ ...37
POWER DISTRIBUTION SYSTEM : System Dia-
gram .................................................................... ...
37
POWER DISTRIBUTION SYSTEM : System De-
scription ..................................................................
37
DIAGNOSIS SYSTEM (BCM) ............................39
COMMON ITEM ..................................................... ...39
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ................................................. ...
39
INTELLIGENT KEY ................................................ ...40
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ...................................
40
ECU DIAGNOSIS INFO RMATION ..............45
BCM ................................................................ ...45
List of ECU Reference ......................................... ...45
WIRING DIAGRAM .....................................46
POWER DISTRIBUTION SYSTEM ................ ...46
Wiring Diagram .................................................... ...46
BASIC INSPECTION ...................................53
DIAGNOSIS AND REPAIR WORK FLOW ..... ...53
Work Flow ............................................................ ...53
DTC/CIRCUIT DIAGNOSIS ...................... ...56
B2614 ACC RELAY CIRCUIT ........................ ...56
DTC Logic ............................................................ ...56
Diagnosis Procedure ..............................................56
Component Inspection ............................................57
B2615 BLOWER RELAY CIRCUIT ...................59
DTC Logic ............................................................ ...59
Diagnosis Procedure ..............................................59
Component Inspection ......................................... ...60
B2616 IGNITION RELAY CIRCUIT ...................61
DTC Logic ............................................................ ...61
Diagnosis Procedure ...............................................61
Component Inspection ............................................62
B2618 BCM .......................................................63
DTC Logic ............................................................ ...63
Diagnosis Procedure ...............................................63
B261A PUSH-BUTTON IGNITION SWITCH .....64
DTC Logic ............................................................ ...64
Diagnosis Procedure ...............................................64
B26F1 IGNITION RELAY ..................................66
DTC Logic ............................................................ ...66
Diagnosis Procedure ...............................................66
B26F2 IGNITION RELAY ..................................68
DTC Logic ............................................................ ...68
Diagnosis Procedure ...............................................68
B26F6 BCM .......................................................70
DTC Logic ............................................................ ...70
Diagnosis Procedure ...............................................70
PUSH-BUTTON IGNITION SWITCH .................71
Component Function Check ............................... ...71
Diagnosis Procedure ...............................................71
Component Inspection ............................................72
PUSH-BUTTON IGNITION SWITCH POSI-
TION INDICATOR ..............................................
74
Description ........................................................... ...74
Component Function Check ..................................74
Diagnosis Procedure ...............................................74
SYMPTOM DIAGNOSIS ............................76
PUSH-BUTTON IGNITION SWITCH DOES
NOT OPERATE .............................................. ...
76
Description ........................................................... ...76
Diagnosis Procedure ...............................................76
PUSH-BUTTON IGNITION SWITCH POSI-
TION INDICATOR DOES NOT ILLUMINATE ...
77
Description ..............................................................77
Diagnosis Procedure ...............................................77
REMOVAL AND INSTALLATION ..............78
PUSH-BUTTON IGNITION SWITCH .............. ...78
Exploded View ..................................................... ...78
Removal and Installation .........................................78
Revision: 2010 May2011 QX56

PCS-8
< SYSTEM DESCRIPTION >[IPDM E/R]
SYSTEM
POWER CONTROL SYSTEM : System Diagram
INFOID:0000000006220164
POWER CONTROL SYSTEM : System DescriptionINFOID:0000000006220165
COOLING FAN CONTROL
IPDM E/R outputs cooling fan control signal (PWM signal ) to the electrically-controlled cooling fan coupling
according to the status of the cooling fan speed request signal received from ECM via CAN communication.
Refer to EC-41, "
COOLING FAN CONTROL : System Diagram".
ALTERNATOR CONTROL
IPDM E/R outputs power generation command signal (PWM signal ) to the alternator according to the status of
the power generation command value signal received from ECM via CAN communication. Refer to CHG-7,
"POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM : System Diagram".
SIGNAL BUFFER SYSTEM
SIGNAL BUFFER SYSTEM : System DiagramINFOID:0000000006220166
SIGNAL BUFFER SYSTEM : System DescriptionINFOID:0000000006220167
 IPDM E/R reads the status of the oil pressure switch and transmits the oil pressure switch signal to BCM via
CAN communication. Refer to MWI-15, "
OIL PRESSURE WARNING LAMP : System Diagram".
 IPDM E/R reads the status of the hood switch and tr ansmits the hood switch signal to BCM via CAN commu-
nication. Refer to SEC-17, "
VEHICLE SECURITY SYSTEM : System Diagram".
 IPDM E/R receives the rear window defogger control signal from BCM via CAN communication and trans- mits it to ECM and AV control unit via CAN communication. Refer to DEF-6, "
System Diagram".
POWER CONSUMPTION CONTROL SYSTEM
JMMIA0491GB
JPMIA0952GB
Revision: 2010 May2011 QX56

PCS-12
< SYSTEM DESCRIPTION >[IPDM E/R]
DIAGNOSIS SYSTEM (IPDM E/R)
CONSULT-III Function (IPDM E/R)
INFOID:0000000006220171
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
Refer to PCS-22, "DTCIndex".
DATA MONITOR
Monitor item
Oil pressure warning lamp does not operate Perform auto active test.
Does the oil pressure warning
lamp blink?YES
 Harness or connector be-
tween IPDM E/R and oil
pressure switch
 Oil pressure switch
IPDM E/R
NO  CAN communication signal
between IPDM E/R and
BCM
 CAN communication signal
between BCM and combi-
nation meter
 Combination meter
Symptom Inspection contents Possible cause
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item [Unit] MAIN SIG-
NALS Description
RAD FAN REQ
[1/2/3/4] ×Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On] ×Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TA I L & C L R R E Q
[Off/On] ×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On] ×Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On] ×Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On] ×Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi] ×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P] ×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK] ×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On] Displays the status of the ignition switch ON signal received from BCM via CAN
communication.
IGN RLY
[Off/On] ×
Displays the status of the ignition relay judged by IPDM E/R.
Revision: 2010 May2011 QX56

PCS
IPDM E/RPCS-15
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
ECU DIAGNOSIS INFORMATION
IPDM E/R
Reference ValueINFOID:0000000006220172
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status
RAD FAN REQ Engine idle speed Changes depending on engine
coolant temperature, air condition-
er operation status, vehicle speed,
etc.0 – 100 %
AC COMP REQ Engine running A/C switch OFF Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ Lighting switch OFF Off
Lighting switch 1ST, 2ND or AUTO (Light is illuminated) On
HL LO REQ Lighting switch OFF Off
Lighting switch 2ND or AUTO (Light is illuminated) On
HL HI REQ Lighting switch 2ND or
AUTO (Light is illuminated) Lighting switch other than HI and
PA S S
Off
Lighting switch HI or PASS On
FR FOG REQ Lighting switch 2ND or
AUTO (Light is illuminated) Front fog lamp switch OFF Off
Front fog lamp switch ON On
FR WIP REQ Ignition switch ON Front wiper switch OFF Stop
Front wiper switch INT 1LOW
Front wiper switch LO Low
Front wiper switch HI Hi
WIP AUTO STOP Ignition switch ON Front wiper stop position STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT Ignition switch ON Front wiper operates normally. Off
Front wiper stops at fail-safe opera-
tion.
BLOCK
IGN RLY1 -REQ Ignition switch OFF or ACC Off
Ignition switch ON On
IGN RLY Ignition switch OFF or ACC Off
Ignition switch ON On
PUSH SW Release the push-button ignition switch Off
Press the push-button ignition switch On
INTER/NP SW Ignition switch ON Selector lever in any position other
than P or N
Off
Selector lever in P or N position On
ST RLY CONT Ignition switch ON Off
At engine cranking On
IHBT RLY -REQ Ignition switch ON Off
At engine cranking On
Revision: 2010 May2011 QX56

PCS-16
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R
ST/INHI RLYIgnition switch ON Off
At engine cranking INHI ON
→ ST ON
The status of starter relay or starter control relay cannot be recognized by
the battery voltage malfunction, etc. when the starter relay is ON and the
starter control relay is OFF. UNKWN
DETENT SW Ignition switch ON  Pull the selector lever with selec-
tor lever in P position.
 Selector lever in any position oth-
er than P. Off
Release the selector lever with selector lever in P position. On
S/L RLY -REQ None of the conditions below are present. Off
 Open the driver door after the ignition switch is turned OFF (for a few
seconds).
 Press the push-button ignition switch when the steering lock is activat-
ed. On
S/L STATE Steering lock is locked. LOCK
Steering lock is unlocked. UNLK
[DTC: B210A] is detected. UNKWN
OIL P SW Ignition switch OFF or ACC
Open
Ignition switch ON (engine running)
Ignition switch ON (engine stopped) Close
HOOD SW Close the hood Off
Open the hood On
HL WASHER REQ Not operating Off
Headlamp washer operating On
THFT HRN REQ Not operation Off
 Panic alarm is activated
 Theft warning alarm is activated
On
HORN CHIRP Not operation Off
Door locking with Intelligent Key (horn chirp mode) On
Monitor Item Condition Value/Status
Revision: 2010 May2011 QX56

PCS
IPDM E/RPCS-17
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
TERMINAL LAYOUT
PHYSICAL VALUES
JPMIA1423ZZ
Te r m i n a l N O .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+–
1
(W) Ground Battery power supply Input Ignition switch OFF Battery voltage
2
(G) Ground Battery power supply Input Ignition switch OFF Battery voltage
3
(R) Ground Starter motor Output Ignition switch ON 0 V
At engine cranking Battery voltage
4
(L) Ground Battery power supply Input Ignition switch OFF Battery voltage
5
(P/L) Ground
Ignition relay power
supply OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
7
(W/G) Ground
Ignition relay power
supply OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
8
(W) Ground Battery power supply Input Ignition switch OFF Battery voltage
9
(B) Ground Ground — Ignition switch ON 0 V
14
(L) Ground Rear window defogger Output
Ignition switch
ONRear window defogger
switch OFF
0 V
Rear window defogger
switch ON Battery voltage
Revision: 2010 May2011 QX56

PCS-18
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R
17
(B) Ground Cooling fan motor
ground
Output Ignition switch ON 0 V
18
(B) Ground Ground — Ignition switch ON 0 V
19
(V) Ground Front fog lamp (RH) Output Lighting
switch 2ND or
AUTO (Light
is illuminated)Front fog lamp switch
OFF
0 V
Front fog lamp switch ON Battery voltage
20
(W) Ground Front fog lamp (LH) Output Lighting
switch 2ND or
AUTO (Light
is illuminated)Front fog lamp switch
OFF
0 V
Front fog lamp switch ON Battery voltage
21
(L) Ground
Headlamp washer re-
lay control Output
Ignition switch
ON Headlamp washer acti-
vated
0 V
Headlamp washer deacti-
vated 12 V
23
(GR/R) Ground Cranking request Output Select lever P or N (Ignition switch ON) 0 V
Select lever in any position other than P or
N (Ignition switch ON)
12 V
Engine running 12 V
24
(W/G) Ground Oil pressure switch Input Ignition switch
ONEngine stopped 0 V
Engine running 12 V
25
(L/Y) Ground Front wiper stop posi-
tion InputIgnition switch
ON Front wiper stop position 0 V
Any position other than
front wiper stop position
12 V
26
(P) Ground CAN-L Input/
Output ——
27
(L) Ground CAN-H
Input/
Output ——
30
(R/W) Ground Starter relay control Output  Ignition switch OFF or ACC
 At engine cranking
0 V
 Ignition switch ON
 Engine running 12 V
31
(B) Ground Injector relay control Output  Approximately 1 second after turning
the ignition switch ON
 Engine running 0 - 1.5 V
Approximately 1 second or more after turn-
ing the ignition switch ON Battery voltage
32
(LG) Ground Hood switch Input Close the hood 12 V
Open the hood 0 V
33
(R) Ground Alternator control Output Ignition switch OFF or ACC 0 V
Ignition switch ON 6 V
34
(P/B) Ground Horn relay control Output The horn is deactivated Battery voltage
The horn is activated 0 V
Te r m i n a l N O .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+–
Revision: 2010 May2011 QX56

PCS
IPDM E/RPCS-19
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
35
(W) Ground ECM relay power sup-
ply OutputIgnition switch OFF
(More than a few seconds after turning ig-
nition switch OFF)
0 V
 Ignition switch ON
 Ignition switch OFF (For a few seconds after turning ignition
switch OFF) Battery voltage
36
(V) Ground ECM relay power sup-
ply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
37
(L) Ground Parking lamp (RH) Output Ignition switch
ONLighting switch OFF 0 V
Lighting switch 1ST Battery voltage
38
(Y) Ground Tail lamp (RH) Output Ignition switch
ONLighting switch OFF 0 V
Lighting switch 1ST Battery voltage
39
(L/B) Ground Front wiper HI Output Ignition switch
ONFront wiper switch OFF 0 V
Front wiper switch LO 9 V
Front wiper switch HI Battery voltage
41
(L/G) Ground ECM relay control Output Ignition switch OFF
(More than a few seconds after turning ig-
nition switch OFF)
Battery voltage
 Ignition switch ON
 Ignition switch OFF (For a few seconds after turning ignition
switch OFF) 0 - 1.5 V
42
(L) Ground Battery power supply Output Ignition switch OFF
(More than a few seconds after turning ig-
nition switch OFF)
0 V
 Ignition switch ON
 Ignition switch OFF (For a few seconds after turning ignition
switch OFF) Battery voltage
43
(LG) Ground Parking lamp (LH) Output
Ignition switch
ONLighting switch OFF 0 V
Lighting switch 1ST Battery voltage
44
(L/W) Ground Tail lamp (LH), license
plate lamp
OutputIgnition switch
ON Lighting switch OFF 0 V
Lighting switch 1ST Battery voltage
45
(Y/R) Ground Front wiper LO Output Ignition switch
ONFront wiper switch OFF 0 V
Front wiper switch LO Battery voltage
46
(L/W) Ground
Steering lock unit pow-
er supply OutputIgnition switch ACC or ON 0 V
Ignition switch
OFF
A few seconds after
opening the driver door
Battery voltage
Ignition switch
LOCK Press the push-button ig-
nition switch
Battery voltage
48
(BR) Ground P/N position Input Select lever in any position other than P or
N (Ignition switch ON)
0 V
Select lever P or N (Ignition switch ON) 12 V
49
(R) Ground Headlamp HI (RH) Output Lighting
switch 2ND or
AUTO (Light
is illuminated)Lighting switch other than
HI and PASS
0 V
 Lighting switch HI
 Lighting switch PASS Battery voltage
Te r m i n a l N O .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+–
Revision: 2010 May2011 QX56

PCS-20
< ECU DIAGNOSIS INFORMATION >[IPDM E/R]
IPDM E/R
50
(LG/B) Ground Headlamp HI (LH) Output Lighting
switch 2ND or
AUTO (Light
is illuminated)Lighting switch other than
H and PASS
0 V
 Lighting switch HI
 Lighting switch PASS Battery voltage
51
(BR/Y) Ground Headlamp LO (LH) Output Lighting switch OFF 0 V
Lighting switch 2ND or AUTO (light is illu-
minated)
Battery voltage
52
(W) Ground Headlamp LO (RH) Output Lighting switch OFF 0 V
Lighting switch 2ND or AUTO (light is illu-
minated)
Battery voltage
54
(SB) Ground ECM power supply Output Approximately 1 second or more than after
turning the ignition switch ON
0 V
 Approximately 1 second after turning the ignition switch ON
 Engine running Battery voltage
55
(O) Ground Throttle control motor
relay power supply
OutputIgnition switch OFF
(More than a few seconds after turning ig-
nition switch OFF)
0 V
 Ignition switch ON
 Ignition switch OFF (For a few seconds after turning ignition
switch OFF) Battery voltage
56
(L) Ground A/C compressor power
supply OutputEngine run-
ning A/C switch OFF 0 V
A/C switch ON
(A/C compressor is oper-
ating)
Battery voltage
57
(V) Ground Ignition relay power
supply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
58
(BR/R) Ground Ignition relay power
supply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
59
(W/B) Ground Ignition relay power
supply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
60
(V/R) Ground
Throttle control motor
relay control OutputIgnition switch ON
→ OFF 0 - 1.0 V
↓
Battery voltage
↓
0 V
Ignition switch ON 0 - 1.0 V
61
(W) Ground Ignition relay power
supply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
62
(SB) Ground Ignition relay power
supply
OutputIgnition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
63
(P) Ground Steering lock unit con-
dition-2
InputSteering lock is unlocked 0 V
Steering lock is locked 12 V
64
(G/Y) Ground A/T shift selector
(detention switch) InputIgnition switch
ON Select lever P 0 V
Select lever in any posi-
tion other than P
12 V
65
(L) Ground
Steering lock unit con-
dition-1 InputSteering lock is unlocked 12 V
Steering lock is locked 0 V
Te r m i n a l N O .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+–
Revision: 2010 May2011 QX56

PCS
IPDM E/RPCS-21
< ECU DIAGNOSIS INFORMATION > [IPDM E/R]
C
D
E
F
G H
I
J
K L
B A
O P
N
Fail-SafeINFOID:0000000006220173
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible,
IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM
If No CAN Communication Is Available With BCM
66
(SB) Ground
Push-button ignition
switch InputPress the push-button ignition switch 0 V
Release the push-button ignition switch 12 V
68
(O) Ground Ignition relay monitor Input Ignition switch OFF or ACC 12 V
Ignition switch ON 0 V
69
(W/B) Ground Ignition power supply Output Ignition switch OFF or ACC 0 V
Ignition switch ON Battery voltage
72
(Y/R) Ground Cooling fan control Output Ignition switch
OFF 5 V
ACC 0 V
ON
2. 5 V
Engine running
Te r m i n a l N O .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
+–
JMMIA0404GB
Control part Fail-safe operation
Cooling fan  Transmits the pulse duty signal (PWM signal) 100% when the ignition switch is turned ON.
 Transmits the pulse duty signal (PWM signal)
0% when the ignition switch is turned OFF.
A/C compressor A/C relay OFF
Alternator Transmits the power generation command signal (PWM signal) 0%
Control part Fail-safe operation
Headlamp  Turns ON the headlamp low relay when the ignition switch is turned ON
 Turns OFF the headlamp low relay when the ignition switch is turned OFF
 Headlamp high relay OFF
Parking lamp
 License plate lamp
 Illumination
 Tail lamp
 Side marker lamp  Turns ON the tail lamp relay when the ignition switch is turned ON
 Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper motor  The status just before activation of fail-safe control is maintained until the ignition switch is
turned OFF while the front wiper is operating at LO or HI speed.
 The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe con-
trol is activated while the front wiper is set in the INT mode and the front wiper motor is op-
erating.
 Return automatically wiper to stop position when ignition switch is turned ON if fail-safe con-
trol is activated while front wiper motor is operated and wiper stops in the other position than
stop position.
Front fog lamp Front fog lamp relay OFF
Horn Horn OFF
Revision: 2010 May2011 QX56