display INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 1725 of 5598
P POSITION WARNING DOES NOT OPERATEDLK-189
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
P POSITION WARNING DOES NOT OPERATE
DescriptionINFOID:0000000006226026
P position warning function does not operate fo r vehicle with information display models
NOTE:
Warning functions operating condition is extremely comp licated, during operating confirmations, reconfirm the
list above twice in order to ensure proper operation. Refer to DLK-27, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000006226027
1.CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis relevant to DTC indicated.
3.CHECK DOOR SWITCH
Check front door switch (driver side).
Refer to DLK-117, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
Refer to DLK-146, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK INFORMATION DISPLAY
Check information display.
Refer to DLK-147, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to DLK-143, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the malfunctioning parts.
7.REPLACE BCM
Replace BCM. Refer to BCS-81, "
Removal and Installation".
Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
Revision: 2010 May2011 QX56
Page 1727 of 5598
ACC WARNING DOES NOT OPERATEDLK-191
< SYMPTOM DIAGNOSIS >
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
ACC WARNING DOES NOT OPERATE
DescriptionINFOID:0000000006226028
ACC warning function does not operate for vehicle with information display models
NOTE:
Warning functions operating condition is extremely comp licated, during operating confirmations, reconfirm the
list above twice in order to ensure proper operation. Refer to DLK-27, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000006226029
1.CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis relevant to DTC indicated.
3.CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
Refer to DLK-146, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK INFORMATION DISPLAY
Check information display.
Refer to DLK-147, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.REPLACE BCM
Replace BCM. Refer to BCS-81, "
Removal and Installation".
Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-40, "
Intermittent Incident".
Revision: 2010 May2011 QX56
Page 1728 of 5598
DLK-192
< SYMPTOM DIAGNOSIS >
TAKE AWAY WARNING DOES NOT OPERATE
TAKE AWAY WARNING DOES NOT OPERATE
DescriptionINFOID:0000000006226030
Take away warning function does not operate for vehicle with information display models.
NOTE:
Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm the
list above twice in order to ensure proper operation. Refer to DLK-27, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000006226031
1.CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis relevant to DTC indicated.
3.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Instrument center: Refer to DLK-104, "
DTC Logic".
Console: Refer to DLK-106, "
DTC Logic".
Luggage room: Refer to DLK-108, "
DTC Logic".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK DOOR SWITCH
Check front door switch (driver side).
Refer to DLK-117, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
Refer to DLK-146, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CHECK INFORMATION DISPLAY
Check information display.
Refer to DLK-147, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the malfunctioning parts.
7.CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to DLK-143, "
ComponentFunctionCheck".
Revision: 2010 May2011 QX56
Page 1730 of 5598
DLK-194
< SYMPTOM DIAGNOSIS >
KEY ID WARNING DOES NOT OPERATE
KEY ID WARNING DOES NOT OPERATE
DescriptionINFOID:0000000006226032
Key ID warning function does not operate for vehicle with information display models.
NOTE:
Warning functions operating condition is extremely comp licated, during operating confirmations, reconfirm the
list above twice in order to ensure proper operation. Refer to DLK-27, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000006226033
1.CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis relevant to DTC indicated.
3.CHECK INTELLIGENT KEY
Check Intelligent Key.
Refer to DLK-145, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts.
4.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Instrument center: Refer to DLK-104, "
DTC Logic".
Console: Refer to DLK-106, "
DTC Logic".
Luggage room: Refer to DLK-108, "
DTC Logic".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK INFORMATION DISPLAY
Check information display.
Refer to DLK-147, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.REPLACE BCM
Replace BCM. Refer to BCS-81, "
Removal and Installation".
Confirm the operation after replacement.
Is the result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-40, "
Intermittent Incident".
Revision: 2010 May2011 QX56
Page 1731 of 5598
INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE
DLK-195
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE
DescriptionINFOID:0000000006226034
Intelligent Key low battery warning does not operat e for vehicle with information display models.
NOTE:
Warning functions operating condition is extremely comp licated, during operating confirmations, reconfirm the
list above twice in order to ensure proper operation. Refer to DLK-27, "
WARNING FUNCTION : System
Description".
Diagnosis ProcedureINFOID:0000000006226035
1.CHECK DTC WITH BCM
Check that DTC is not detected with BCM
Is the inspection result normal?
YES >> GO TO 2.
NO >> Perform trouble diagnosis relevant to DTC indicated.
2.CHECK DTC WITH COMBINATION METER
Check that DTC is not detected with combination meter
Is the inspection result normal?
YES >> GO TO 3.
NO >> Perform trouble diagnosis relevant to DTC indicated.
3.CHECK “LO- BATT OF KEY FOB WARN” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM”.
2. Select “LO- BATT OF KEY FOB WARN” in “WORK SUPPORT” mode.
3. Check “LO- BATT OF KEY FOB WARN” setting in “WORK SUPPORT”. Refer to DLK-41, "
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Set “ON” in “LO- BATT OF KEY FOB WARN”.
4.CHECK INTELLIGENT KEY
Check Intelligent Key.
Refer to DLK-145, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.CHECK INSIDE KEY ANTENNA
Check inside key antenna.
Instrument center: Refer to DLK-104, "
DTC Logic".
Console: Refer to DLK-106, "
DTC Logic".
Luggage room: Refer to DLK-108, "
DTC Logic".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace the malfunctioning parts.
6.CHECK INFORMATION DISPLAY
Check information display.
Refer to DLK-147, "
ComponentFunctionCheck".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace the malfunctioning parts.
7.REPLACE BCM
Replace BCM. Refer to BCS-81, "
Removal and Installation".
Revision: 2010 May2011 QX56
Page 1805 of 5598
DLN-3
CEF
G H
I
J
K L
M A
B
DLN
N
O P
U1000 CAN COMM CIRCUIT ......................... ....91
Description .......................................................... ....91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
U1010 CONTROL UNIT (CAN) ..........................92
Description .......................................................... ....92
DTC Logic ...............................................................92
Diagnosis Procedure ...............................................92
POWER SUPPLY AND GROUND CIRCUIT ......93
Description .......................................................... ....93
Diagnosis Procedure ...............................................93
4WD WARNING LAMP ......................................97
Component Function Check ................................ ....97
Diagnosis Procedure ...............................................97
4WD INDICATOR LAMP ....................................98
Component Function Check ................................ ....98
Diagnosis Procedure ...............................................98
SYMPTOM DIAGNOSIS ..............................99
HEAVY TIGHT-CORNER BRAKING SYMP-
TOM OCCURS . .............................................. ....
99
Description .......................................................... ....99
Diagnosis Procedure ...............................................99
4WD MODE DOES NOT CHANGE ..................100
Description .......................................................... ..100
Diagnosis Procedure .............................................100
4WD MODE INDICATOR LAMP CONTINUES
BLINKING .........................................................
101
Description .......................................................... ..101
Diagnosis Procedure .............................................101
4WD WARNING LAMP BLINKS QUICKLY .....102
Description .......................................................... ..102
4WD WARNING LAMP BLINKS SLOWLY .....103
Description .......................................................... ..103
Diagnosis Procedure .............................................103
INFORMATION DISPLAY IS NOT DIS-
PLAYED ...........................................................
104
Description .......................................................... ..104
Diagnosis Procedure .............................................104
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING ..........................
105
NVH Troubleshooting Chart ................................ ..105
PERIODIC MAINTENANCE .......................106
TRANSFER FLUID ......................................... ..106
Inspection ............................................................ ..106
Draining .................................................................106
Refilling .................................................................106
REMOVAL AND INSTALLATION .............107
TRANSFER CONTROL UNIT .........................107
Removal and Installation ..................................... ..107
4WD MODE SWITCH ......................................108
Removal and Installation .......................................108
FRONT OIL SEAL ...........................................109
Exploded View .......................................................109
Removal and Installation .......................................109
REAR OIL SEAL .............................................111
Exploded View .......................................................111
Removal and Installation .......................................111
Adjustment .............................................................112
TRANSFER CONTROL ACTUATOR .............114
Exploded View .......................................................114
Removal and Installation .......................................114
Inspection ..............................................................114
TRANSFER HI-LO POSITION SENSOR ........116
Exploded View .......................................................116
Removal and Installation .......................................116
Inspection ..............................................................116
TRANSFER ROTARY POSITION SENSOR ...117
Exploded View .......................................................117
Removal and Installation .......................................117
Inspection ..............................................................118
TRANSFER LOCK POSITION SENSOR ........119
Exploded View .......................................................119
Removal and Installation .......................................119
Inspection ..............................................................119
TRANSFER FLUID TEMPERATURE SEN-
SOR .................................................................
120
Exploded View .......................................................120
Removal and Installation .......................................120
Inspection ..............................................................120
UNIT REMOVAL AND INSTALLATION ....121
TRANSFER ASSEMBLY ................................121
Exploded View ..................................................... ..121
Removal and Installation .......................................121
INPUT OIL SEAL ............................................123
Exploded View .......................................................123
Removal and Installation .......................................123
SERVICE DATA AND SPECIFICATIONS
(SDS) ............... ...........................................
124
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
124
General Specifications ......................................... ..124
FRONT PROPELLER SHAFT: 2F P15
PREPARATION ........ .................................
125
PREPARATION ...............................................125
Revision: 2010 May2011 QX56
Page 1821 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEMDLN-19
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
4WD SHIFT SWITCH AND 4WD SHIFT INDICATOR LAMP
*1: Blinking 2 times/1 second
*2: “4HI” and “4LO” blink a](/img/42/57033/w960_57033-1820.png "INFINITI QX56 2011 Factory Service Manual
SYSTEMDLN-19
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
4WD SHIFT SWITCH AND 4WD SHIFT INDICATOR LAMP
*1: Blinking 2 times/1 second
*2: “4HI” and “4LO” blink a")
SYSTEMDLN-19
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
4WD SHIFT SWITCH AND 4WD SHIFT INDICATOR LAMP
*1: Blinking 2 times/1 second
*2: “4HI” and “4LO” blink alternately.
CONDITION FOR TURN ON THE WARNING LAMP
TCM Transmits the following signals via CAN communication line to transfer control unit.
Shift position signal
Gear position signal
Output shaft revolution signal
Steering angle sensor Transmits the following signals via CAN communication line to transfer control unit.
Steering angle sensor signal
Combination meter Receives the following signals via CAN communication line from transfer control unit.
4WD warning lamp signal
ATP warning lamp signal
4WD mode indicator signal
Component parts Control signal
4WD shift switch 4WD shift indicator lamp (in Information display) 4WD shift procedure
AUTO
1. Start the engine.
2. Turn the 4WD shift switch.
NOTE:
Mode can be switched between AU-
TO⇔4H while driving straight.
4H
↓↑
4WD status: 4H ⇔4L (Blinking)
*1*2
1. Start the engine.
2. Never drive the vehicle.
3. Shift A/T shift selector to N position.
4. Press and rotate 4WD shift switch
while depressing brake pedal.
CAUTION:
4WD mode does not switch when 4WD
shift switch is operated while the vehi-
cle is running or A/T shift selector is
shifted to any position other than neu-
tral.
4L
JPDIE0230ZZJPDIE0234ZZ
JPDIE0231ZZJPDIE0235ZZ
JPDIE0231ZZ
JPDIE0233ZZ
JPDIE0236ZZ
JPDIE0233ZZJPDIE0237ZZ
Revision: 2010 May2011 QX56
Page 1823 of 5598
![INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-21
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
DIAGNOSIS SYSTEM (TRA NSFER CONTROL UNIT)
CONSULT-III FunctionINFOID:0000000](/img/42/57033/w960_57033-1822.png "INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-21
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
DIAGNOSIS SYSTEM (TRA NSFER CONTROL UNIT)
CONSULT-III FunctionINFOID:0000000")
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-21
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
DIAGNOSIS SYSTEM (TRA NSFER CONTROL UNIT)
CONSULT-III FunctionINFOID:0000000006222226
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes as follows.
*: The following diagnosis information is erased by erasing.
DTC
ECU IDENTIFICATION
Transfer control unit part number can be read.
SELF DIAGNOSTIC RESULT
Refer to DLN-29, "DTC Index".
When "0" is displayed on self-diagnosis result.
The system is presently malfunctioning.
When except "0" is displayed on self-diagnosis result. System malfunction in the past is detec ted, but the system is presently normal.
NOTE:
Each time when ignition switch is turned OFF to ON, numerical number increases in 1 →2→ 3...110 →111 .
When the operation number of times exceeds 111, the number do not increase and “111” is displayed until
self-diagnosis is erased
*.
*: For “U1000” and “U1010”, the maximum value is “39”.
DATA MONITOR
X:Applicable
Diagnostic test mode Function
ECU Identification Transfer control unit part number can be read.
Self Diagnostic Result Self-diagnostic results can be read and erased quickly.*
Data Monitor Input/Output data in the transfer control unit can be read.
Work Support This mode enables a technican to adjust some devices faster and more accurately by following the
indications on the CONSULT-III
Monitor item (Unit) SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS MAIN SIG-
NALS
4WD MODE [BOTNG/SWTNG/4L/4H/AUTO] X Control status of 4WD mode is displayed.
2WD SW [On/Off] X 4WD shift switch (2WD) is not equipped, but it
is displayed.
AUTO SW [On/Off] X 4WD shift switch signal (AUTO) is displayed.
4H SW [On/Off] X 4WD shift switch signal (4H) is displayed.
4L SW [On/Off] X 4WD shift switch signal (4L) is displayed.
T/M RANGE [D/N/R/P] X A/T shift selector position via CAN communica-
tion line is displayed.
N RANGESW [On/Off] X A/T shift selector position (N) via CAN commu-
nication line is displayed.
R RANGE SW [On/Off] X A/T shift selector position (R) via CAN commu-
nication line is displayed.
ING SW [On/Off] X Ignition switch status is displayed.
TCS OPER [On/Off] X TCS operation status via CAN communication
line is displayed.
VDC OPER [On/Off] X VDC operation status via CAN communication
line is displayed.
Revision: 2010 May2011 QX56
Page 1824 of 5598
![INFINITI QX56 2011 Factory Service Manual
DLN-22
< SYSTEM DESCRIPTION >[TRANSFER: ATX90A]
DIAGNOSIS SYSTEM (T
RANSFER CONTROL UNIT)
ABS OPER [On/Off] X ABS operation status via CAN communication
line is displayed.
SAND MODE IND [On/Off] Thi](/img/42/57033/w960_57033-1823.png "INFINITI QX56 2011 Factory Service Manual
DLN-22
< SYSTEM DESCRIPTION >[TRANSFER: ATX90A]
DIAGNOSIS SYSTEM (T
RANSFER CONTROL UNIT)
ABS OPER [On/Off] X ABS operation status via CAN communication
line is displayed.
SAND MODE IND [On/Off] Thi")
DLN-22
< SYSTEM DESCRIPTION >[TRANSFER: ATX90A]
DIAGNOSIS SYSTEM (T
RANSFER CONTROL UNIT)
ABS OPER [On/Off] X ABS operation status via CAN communication
line is displayed.
SAND MODE IND [On/Off] This indicator is not equipped, but it is dis-
played.
ROCK MODE IND [On/Off] This indicator is not equipped, but it is dis-
played.
SNOW MODE IND [On/Off] This indicator is not equipped, but it is dis-
played.
ONROAD MODE IND [On/Off] This indicator is not equipped, but it is dis-
played.
SAND MODE SW [On/Off] X This switch is not equipped, but it is displayed.
ROCK MODE SW [On/Off] X This switch is not equipped, but it is displayed.
SNOW MODE SW [On/Off] X This switch is not equipped, but it is displayed.
ONROAD MODE SW [On/Off] X This switch is not equipped, but it is displayed.
HI/LO POSI SEN 3 [On/Off] X Transfer Hi-Lo position sensor (3) status is dis-
played.
HI/LO POSI SEN 1 [On/Off] X Transfer Hi-Lo position sensor (1) status is dis-
played.
LOCK POSI SEN [OPEN/LOCK/BAT/UNLEAN/HI
TEMP/ERROR/GND] X
Transfer lock position sensor signal is dis-
played.
ATP IND [On/Off] Control status of ATP warning lamp is dis-
played.
4WD FAILLAMP [On/Off] X Control status of ATP warning lamp is dis-
played.
4WD MODE IND [4L/LOCK/AUTO] X Control status of 4WD mode indicator lamp is
displayed.
(LOCK means 4H of 4WD mode)
MOTOR DRIVE B [HI/LO/PWM] X Driving status of transfer motor is displayed.
(Reverse side)
MOTOR DRIVE A [HI/LO/PWM] X Driving status of transfer motor is displayed.
(Drive side)
FLUID TEMP SEN [V] X Temperature of transfer fluid is displayed.
MOTOR TEMP [V] X Temperature of transfer motor is displayed.
C/U POWER SUP [V] X Power supply voltage value of transfer control
unit is displayed.
MOTOR POWER SUP [V] X Power supply voltage value of transfer motor
unit is displayed.
ROTARY POSI SEN [%] X Transfer rotary position sensor signal is dis-
played.
THRTL POSI SEN [%] X X Throttle opening status via CAN communica-
tion line is displayed.
AT R SPEED [km/h] X Output shaft revolution speed via CAN commu-
nication line is displayed.
T/M GEAR [0 - 7] X Current transmission gear via CAN communi-
cation line is displayed.
COMPR VHCL SPEED [km/h] X Vehicle speed calculated by transfer control
unit is displayed.
VHCL/S SEN-FR [km/h] X Wheel speed (front) average calculated by
transfer control.
Monitor item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS MAIN SIG-
NALS
Revision: 2010 May2011 QX56
Page 1825 of 5598
![INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-23
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
WORK SUPPORT
*: “LOCK SLEEVE SENSOR” means transfer lock position sensor](/img/42/57033/w960_57033-1824.png "INFINITI QX56 2011 Factory Service Manual
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-23
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
WORK SUPPORT
*: “LOCK SLEEVE SENSOR” means transfer lock position sensor")
DIAGNOSIS SYSTEM (TRANSFER CONTROL UNIT)
DLN-23
< SYSTEM DESCRIPTION > [TRANSFER: ATX90A]
C
EF
G H
I
J
K L
M A
B
DLN
N
O P
WORK SUPPORT
*: “LOCK SLEEVE SENSOR” means transfer lock position sensor.
VHCL/S SEN-RR [km/h] X Wheel speed (rear) average calculated by
transfer control.
ENG SPEED [rpm] X Engine status via CAN communication line is
displayed.
INTERNL SPEED SEN [count] X Transfer internal speed sensor status is dis-
played.
TRANSFER TORQUE [Nm] X Commanded transfer communication torque is
displayed.
UNIT PARAMETER [A1 - A9, B1 - B9, C1 - C9, D1
- D9, E1 - E9, F1 - F9, G1 - G9, H1 - H9, J1 - J9] Unit parameter of transfer recognized by trans-
fer control unit is displayed.
Monitor item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALS MAIN SIG-
NALS
Function Description
UNIT CHARACTERISTIC WRITE Writes the unit parameter of transfer to transfer control unit.
START CALIBRATION Perform initial calibration of transfer control unit.
LOCK SLEEVE SENSOR
* INITIALIZE Format learning the transfer lock position sensor written to transfer control unit.
LOCK SLEEVE SENSOR
* LEARNING Perform learning the transfer lock position sensor.
OIL DETERIORATION INFO RESET Format the transfer fl uid viscosity written to transfer control unit.
Revision: 2010 May2011 QX56