door INFINITI QX56 2011 Factory Service Manual

REAR AUTOMATIC AIR CONDITIONING SYSTEMHAC-135
< SYMPTOM DIAGNOSIS > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
REAR AUTOMATIC AIR CONDITIONING SYSTEM
Diagnosis Chart By SymptomINFOID:0000000006275981
NOTE:
 Perform the self-diagnoses with CONSULT-III before performing the symptom diagnosis. If DTC is detected,
perform the corresponding diagnosis.
 The following table is based on the condition that fr ont automatic air conditioning system operates normally.
Symptom Corresponding malfunction part Reference
 Rear air conditioning system cannot be controlled. (Front A/C control)
 Operation status of rear air conditioning system is not indicated on front display. Multi AV system
AV- 1 9 9 , "
Symptom Table"
Rear air conditioning sys-
tem cannot be controlled.
(Rear A/C control)Operation status of
rear air conditioning
system is not indicated
on rear A/C control
display
 Power supply system of rear A/C
control
 Rear A/C control HAC-115, "
REAR A/C CONTROL :
Diagnosis Procedure"
Operation status of
rear air conditioning
system is indicated on
rear A/C control dis-
play Communication circuit between rear
A/C control and A/C auto amp.
 A/C auto amp. HAC-127, "
Diagnosis Procedure"
 Air outlet does not change.
 Rear mode door motor does not operate normally.  Circuit between rear mode door mo-
tor and A/C auto amp.
 Rear mode door motor control link- age
 Front mode door motor
 A/C auto amp. HAC-116, "REAR MODE DOOR
MOTOR : Diagnosis Procedure"
 Discharge air temperature does not change.
 Rear air mix door motor does not operate normally.  Circuit between rear air mix door
motor and A/C auto amp.
 Rear air mix door motor installation condition
 Rear air mix door motor
 A/C auto amp. HAC-114, "REAR AIR MIX DOOR
MOTOR : Diagnosis Procedure"
Rear blower motor operation is malfunctioning.
 Power supply system of rear blower
motor
 Circuit between rear blower motor
and A/C auto amp..
 Rear blower motor
 A/C auto amp. HAC-131, "Diagnosis Procedure"
 Insufficient cooling.
 No cool air comes out. (Air flow volume is normal.)  Power supply system of rear A/C re-
lay
 Circuit between rear A/C relay and A/C auto amp..
 Circuit between rear A/C relay and rear A/C solenoid valve.
 Circuit between rear A/C solenoid
valve and ground.
 Rear A/C relay
 Rear A/C solenoid valve
 A/C auto amp.
 Refrigerant cycle
 Air leakage from each duct
 Temperature setti ng trimmer (rear) HAC-139, "REAR AIR CONDI-
TIONER : Diagnosis Procedure"
Revision: 2010 May2011 QX56

HAC-152
< REMOVAL AND INSTALLATION >[AUTOMATIC AIR CONDITIONING]
DOOR MOTOR
DOOR MOTOR
Exploded ViewINFOID:0000000006276008
Front A/C unit
Rear A/C unit
JMIIA0645ZZ
1. A/C unit assembly 2. Upper ventilator door lever 3. Upper ventilator door link
4. Upper ventilator door motor 5. Air mix door motor LH 6. Air mix door adaptor B
7. Air mix door adaptor A 8. Intake door motor 9. Intake door motor lever
10. Intake door lever 11. Blower unit assembly 12. Foot door lever
13. Foot door link 14. Air mix door motor RH 15. Air mix door adaptor
16. Mode door motor 17. Mode door motor lever 18. Mode door motor bracket
19. Main link 20. Ventilator door link 21 Ventilator door lever
22. Defroster lever
JMIIA0646ZZ
Revision: 2010 May2011 QX56

DOOR MOTORHAC-153
< REMOVAL AND INSTALLATION > [AUTOMATIC AIR CONDITIONING]
C
D
E
F
G H
J
K L
M A
B
HAC
N
O P
MODE DOOR MOTOR
MODE DOOR MOTOR : Re moval and InstallationINFOID:0000000006276009
REMOVAL
1. Remove instrument lower panel RH. Refer to IP-14, "Removal and Installation".
2. Remove power steering control unit bracket.
3. Remove fixing screws (A), and then remove mode door motor (1).
4. Disconnect mode door motor connector.
INSTALLATION
Install in the reverse order of removal.
AIR MIX DOOR MOTOR
AIR MIX DOOR MOTOR : Re moval and InstallationINFOID:0000000006276010
REMOVAL
Driver side
1. Remove automatic drive position control unit. Refer to ADP-136, "Removal and Installation".
2. Remove fixing screws (A), and then remove air door motor LH (1).
3. Disconnect air mix door motor connector.
Passenger side
1. Remove heater core. Refer to HA-44, "HEATER CORE : Removal and Installation".
2. Remove fixing screws, and then remove air mix door motor RH.
INSTALLATION
Install in the reverse order of removal.
INTAKE DOOR MOTOR
INTAKE DOOR MOTOR : Re moval and InstallationINFOID:0000000006276011
REMOVAL
1. Remove blower unit assembly. Refer to VTL-15, "Removal and Installation".
2. Remove fixing screws, and then remove intake door motor.
1. Rear A/C unit assembly 2. Rear mode door lever 2 3. Rear mode door lever 1
4. Rear mode door motor 5. Rear air mix door motor
JMIIA0790ZZ
JMIIA0788ZZ
Revision: 2010 May2011 QX56

HAC-154
< REMOVAL AND INSTALLATION >[AUTOMATIC AIR CONDITIONING]
DOOR MOTOR
3. Disconnect intake door motor connector.
INSTALLATION
Install in the reverse order of removal.
UPPER VENTILATOR DOOR MOTOR
UPPER VENTILATOR DOOR MOTO
R : Removal and InstallationINFOID:0000000006276012
REMOVAL
1. Remove automatic drive position control unit. Refer to ADP-136, "Removal and Installation".
2. Remove fixing screws (A), and then remove intake door motor (1).
3. Disconnect intake door motor connector.
INSTALLATION
Install in the reverse order of removal.
REAR MODE DOOR MOTOR
REAR MODE DOOR MOTOR : Removal and InstallationINFOID:0000000006276013
REMOVAL
1. Remove luggage side lower finisher RH. Refer to INT-36, "LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
2. Remove fixing screws, and then remove rear mode door motor.
INSTALLATION
Install in the reverse order of removal.
REAR AIR MIX DOOR MOTOR
REAR AIR MIX DOOR MOTOR : Removal and InstallationINFOID:0000000006276014
REMOVAL
1. Remove rear A/C unit assembly. Refer to HA-47, "REAR A/C UNIT ASSEMBLY : Removal and Installa-
tion".
2. Remove fixing screws, and then remove air mix door motor.
INSTALLATION
Install in the reverse order of removal.
JMIIA0789ZZ
Revision: 2010 May2011 QX56

INL-2
LUGGAGE ROOM LAMP CIRCUIT ..................60
Description ........................................................... ...60
Diagnosis Procedure ..............................................60
STEP LAMP CIRCUIT .......................................62
Description ........................................................... ...62
Component Function Check ...................................62
Diagnosis Procedure ..............................................62
PUDDLE LAMP CIRCUIT ..................................64
Description ........................................................... ...64
Diagnosis Procedure ..............................................64
PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT ..............................................
65
Component Function Check ................................ ...65
Diagnosis Procedure ..............................................65
SYMPTOM DIAGNOSIS .............................67
INTERIOR LIGHTING SYSTEM SYMPTOMS ...67
Symptom Table ................................................... ...67
REMOVAL AND INSTALLATION ...............68
MAP LAMP ..................................................... ...68
Exploded View ..................................................... ...68
Removal and Installation ........................................68
Replacement ..........................................................68
VANITY MIRROR LAMP ...................................69
Exploded View ..................................................... ...69
Replacement ..........................................................69
GLOVE BOX LAMP ...........................................70
Exploded View ..................................................... ...70
Replacement ..........................................................70
FOOT LAMP ......................................................71
DRIVER SIDE ......................................................... ...71
DRIVER SIDE : Exploded View ..............................71
DRIVER SIDE : Replacement ................................71
PASSENGER SIDE ...................................................71
PASSENGER SIDE : Exploded View .....................71
PASSENGER SIDE : Replac ement ........................72
REAR FOOT LAMP ................................................ ...72
REAR FOOT LAMP : Exploded View .....................72
REAR FOOT LAMP : Removal and Installation ......72
STEP LAMP .......................................................74
Exploded View ..................................................... ...74
Removal and Installation .........................................74
Replacement ...........................................................74
MOOD LAMP .....................................................75
FRONT DOOR ARMREST ..................................... ...75
FRONT DOOR ARMREST : Exploded View ..........75
FRONT DOOR ARMREST : Replacement .............75
REAR DOOR ARMREST ....................................... ...75
REAR DOOR ARMREST : Exploded View .............75
REAR DOOR ARMREST : Replacement ...............76
PERSONAL LAMP ............................................77
Exploded View ..................................................... ...77
Removal and Installation .........................................77
Replacement ...........................................................78
PUDDLE LAMP .............................................. ...79
Exploded View ..................................................... ...79
Removal and Installation .........................................79
LUGGAGE ROOM LAMP ..................................81
Exploded View ..................................................... ...81
Removal and Installation .........................................81
Replacement ...........................................................81
SERVICE DATA AND SPECIFICATIONS
(SDS) .......... ................................................
82
SERVICE DATA AND SPECIFICATIONS
(SDS) .............................................................. ...
82
Bulb Specifications ............................................... ...82
Revision: 2010 May2011 QX56

INL-4
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000006216048
Component DescriptionINFOID:0000000006216049
1. BCMRefer to BCS-4, "
BODY CONTROL
SYSTEM : Componen t Parts Loca-
tion"
2. Personal lamp 3. Luggage room lamp
4. Remote keyless entry receiver Refer to DLK-11, "
DOOR LOCK
SYSTEM :
ComponentPartsLocation"
5. Back door lock assembly
(back door switch) 6. Automatic back door close switch
7. Door request switch 8. Door switch 9. Step lamp
10. Paddle lamp 11. Optical sensor 12. IPDM E/R Refer to PCS-4, "
Component Parts
Location"
13. Vanity mirror lamp 14. Combination meter 15. Combination switch
16. Front door lock assembly (driver
side) (door key cylinder switch, un-
lock sensor) 17. Door lock and unlock switch 18. Foot lamp
19. Push-button ignition switch 20. AV control unit Refer to AV- 9 , "
Component Parts Lo-
cation"
21. Map lamp
JMLIA0837ZZ
Part Description
BCM Controls the interior lighting system.
IPDM E/R Controls the integrated relay according to the request signal from BCM (via CAN com-
munication).
Remote keyless entry receiver Refer to DLK-12, "
DOOR LOCK SYSTEM : ComponentDescription".
AV control uni Receives the dimmer signal from BCM via CAN communication.
Optical sensor Refer to EXL-7, "
EXTERIOR LIGHTING SYSTEM : ComponentDescription".
Unlock sensor Detects door lock condition of driver side door.
Revision: 2010 May2011 QX56

COMPONENT PARTSINL-5
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K
M A
B
INL
N
O P
Combination switch
(Lighting & turn signal switch) Refer to
BCS-7, "COMBINATION SWITCH READING SYSTEM : System Description".
 Door lock and unlock switch
 Door request switch
 Door key cylinder switch Inputs the lock/unlock signal to BCM.
 Door switch
 Back door switch Inputs the door switch signal to BCM.
Part Description
Revision: 2010 May2011 QX56

INL-6
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM : System DiagramINFOID:0000000006216050
INTERIOR ROOM LAMP CONTROL SYSTEM : System DescriptionINFOID:0000000006216051
OUTLINE
 Interior room lamps* are controlled by interi or room lamp timer control function of BCM.
*: Map lamp, foot lamp and personal lamp (when map lamp switch and personal lamp switch are in DOOR
position).
 Step lamp is controlled by step lamp control function of BCM.
 Luggage room lamp and automatic back door close switch illumination are controlled by luggage room lamp
control function of BCM.
 Puddle lamp is controlled by puddle lamp timer control function of BCM.
 Push-button ignition switch illumination is controlled by the push-button ignition switch illumination control
function of BCM and combination meter.
 Interior room lamps and puddle lamp are illuminated by welcome light function of Intelligent Key system.
Refer to DLK-26, "
WELCOME LIGHT FUNCTION : System Description".
INTERIOR ROOM LAMP TIMER CONTROL
JMLIA1188GB
Revision: 2010 May2011 QX56

SYSTEMINL-7
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K
M A
B
INL
N
O P
Interior Room Lamp Timer Basic Operation
NOTE:
A: Sets the interior room lamp gradual brightening and dimming time.
B: Gradually brightens from 0% to 100% and gradually dims from 100% to 0% in 1 second.
 The interior room lamp turns ON and OFF (gradual brightening and dimming) by the interior room lamp
timer.
 BCM judges the vehicle condition with the following items. It activates the interior room timer.
- Ignition switch status
- Door switch signal (except back door)
- Door lock/unlock signal (remote keyless entry receiv er, each door request switch, door key cylinder switch,
door lock/unlock switch)
NOTE:
Each function of interior room lamp ti mer can be set by CONSULT-III. Refer to INL-14, "
INT LAMP : CON-
SULT-III Function (BCM - INT LAMP)".
Interior Room Lamp ON Operation
 BCM always turns the interior room lamp ON when any door opens excepting back door.
 When all doors are closed, and any all door unlock operation is performed or ignition switch is turned OFF,
BCM brightens interior room lamp to 30% bri ghtness and maintains 30% brightness until any door opens.
 BCM activates the interior room timer in any of the fo llowing conditions to turn the interior room lamp ON for
a period of time.
- Any door opens before all doors close excepting back door.
- Ignition switch is turned ON → OFF.
- Any door unlock signal is detected when all doors cl ose excepting back door with ignition switch OFF.
NOTE:
The timer restarts if new condition is input during the timer operating time.
Interior Room Lamp OFF Operation
BCM stops the timer and turns interior room lamp OF F, when any of the following conditions is satisfied.
 The interior room lamp timer operating time is expired with all doors closed excepting back door.
 Ignition switch position is other than O FF with all doors close excepting back door.
 Any door lock signal is detected with all doors close excepting back door.
LUGGAGE ROOM LAMP CONTROL
BCM controls the luggage room lamp and automatic back door close switch illumination (ground-side) to turn
ON with back door switch ON.
 When luggage room lamp switch is turned to the ON position, luggage room lamp turns ON.
 When luggage room lamp switch is in the DOOR position and back door is opened, luggage room lamp turns ON.
 When back door is opened, automatic back door close switch illumination turn ON.
STEP LAMP CONTROL
BCM controls the step lamp (ground-side) to turn ON with any door switch ON excepting back door.
PUDDLE LAMP TIMER CONTROL
Puddle Lamp Timer Basic Operation
 BCM controls the ground to turn the puddle lamp ON.
JMLIA0961GB
Revision: 2010 May2011 QX56

INL-8
< SYSTEM DESCRIPTION >
SYSTEM
 The puddle lamp turns ON and OFF by the puddle lamp timer.
 BCM judges the vehicle condition with the following items. It activates the puddle lamp timer.
- Ignition switch status
- Door switch signal (except back door)
- Door lock/unlock signal (remote keyless entry receiver, each door request switch)
- Driver side door lock status
Puddle Lamp ON Operation
BCM activates the puddle lamp timer in any of the following conditions to turn the puddle lamp ON for a period
of time.
 Any door opens excepting back door.
 Any door opens before all doors close excepting back door.
 Ignition switch is turned ON → OFF.
 Door unlock signal by remote keyless entry rece iver or each door request switch is detected.
 Driver side door is locked*.
NOTE:
The timer restarts if new condition is input during the timer operating time.
Puddle Lamp OFF Operation
BCM stops the timer and turns puddle lamp OFF, when any of the following conditions are satisfied.
 The puddle lamp timer operating time is expired.
 The interior room lamp OFF conditions.
 The interior room lamp timer operating time is expired.
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CONTROL
Push-button Ignition Switch Illumination Basic Operation
 BCM controls the ON/OFF status of push-button igni tion switch illumination according to vehicle status.
 BCM provides the push-button ignition switch illumi nation control signal and the ground to turn the push-but-
ton ignition switch illumination ON.
 BCM cuts the ground supply while each illumination (tai l lamp) is ON. BCM switches to the ground control
according to the meter illumination control function. Refer to MWI-16, "
METER ILLUMINATION CONTROL :
System Description".
Heart Beat Operation
BCM repeats brightening and dimming operation of push-button ignition switch illumination when any of the
following conditions are satisfied.
 Welcome light function operates.
 When ignition switch is OFF and any of the following conditions are satisfied.
- Driver side door changes from closed to open
- Driver side door changes from locked to unlocked
- Intelligent Key ID comparison is OK and driver side door changes from open to closed
- ID comparison by Intelligent Key transponder is OK
Illumination ON Operation
When ignition switch is not OFF or tail lamp turns ON, push-button ignition switch illumination turns ON.
Dimming Operation
When tail lamp turns OFF and ignition switch is turned OFF, push-button ignition switch illumination dims to
50% brightness.
Illumination OFF Operation
Push-button ignition switch illumination turns OFF when ignition switch turns OFF and tail lamp turns from ON
to OFF, while push-button ignition switch illumination is in ON status.
When push-button ignition switch illumination is at 50% brightness or in heartbeat status, and any of the fol-
lowing conditions are satisfied, push-butt on ignition switch illumination turns OFF.
 15 seconds after start of heartbeat operation.
 When welcome light function is not operating and any on the following conditions is satisfied.
- Driver side door is closed
- Driver side door is locked
- Intelligent Key ID comparison is NG
- Comparison of Intelligent Key ID by transponder is NG
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
Revision: 2010 May2011 QX56