air condition INFINITI QX56 2011 Factory Workshop Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 319 of 5598
AV
AUX IMAGE SIGNAL CIRCUIT (FRONT AUXILIARY INPUT JACKS TO AV CON-
TROL UNIT)
AV-171
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
AUX IMAGE SIGNAL CIRCUIT (FRONT AUXILIARY INPUT JACKS TO AV
CONTROL UNIT)
DescriptionINFOID:0000000006216334
Transmits the image signal of AUX device from fr ont auxiliary input jacks to AV control unit.
AV control unit transmits the image signal t hat is input to the front display unit.
Diagnosis ProcedureINFOID:0000000006216335
1.CHECK CONTINUITY AUX IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front auxiliary input jacks connector and AV control unit connector.
3. Check continuity between front auxiliary input jacks harness connector and AV control unit harness con-
nector.
4. Check continuity between front auxiliary input jacks harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AUX IMAGE SIGNAL
1. Connect front auxiliary input jacks connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check signal between front auxiliar y input jacks harness connector and ground.
Is the inspection result normal?
YES >> Replace AV control unit. Refer to AV-212, "Removal and Installation".
NO >> Check that there is no malf unction in the external device.
Front auxiliary input jacks AV control unit
Continuity
Connector Terminal Connector Terminal
M139 7 M209 26 Existed
Front auxiliary input jacks GroundContinuity
Connector Terminal
M139 7 Not existed
(+) (− ) Condition Reference value
Front auxiliary input jacks
Connector Terminal
M139 7 Ground At front AUX image is dis-
played.
SKIB2251J
Revision: 2010 May2011 QX56
Page 320 of 5598
AV-172
< DTC/CIRCUIT DIAGNOSIS >
AUX IMAGE SIGNAL CIRCUIT (REAR AUXILIARY INPUT JACKS TO VIDEO DIS-
TRIBUTOR)
AUX IMAGE SIGNAL CIRCUIT (REAR AUXILIARY INPUT JACKS TO VID-
EO DISTRIBUTOR)
DescriptionINFOID:0000000006216336
Transmits the image signal of AUX device from r ear auxiliary input jacks to the video distributor.
Video distributor transmits the image signal that is input to the headrest display unit.
Diagnosis ProcedureINFOID:0000000006216337
1.CHECK CONTINUITY AUX IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear auxiliary input jacks connector and video distributor connector.
3. Check continuity between rear auxiliary input jacks harness connector and video distributor harness con-
nector.
4. Check continuity between rear auxili ary input jacks harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AUX IMAGE SIGNAL
1. Connect rear auxiliary input jacks connector and video distributor connector.
2. Turn ignition switch ON.
3. Check signal between rear auxiliary input jacks harness connector and ground.
Is the inspection result normal?
YES >> Replace video distributor. Refer to AV-215, "Removal and Installation".
NO >> Check that there is no malfunction in the external device.
Rear auxiliary input jacks Video distributor Continuity
Connector Terminal Connector Terminal
M98 7 M218 40 Existed
Rear auxiliary input jacks GroundContinuity
Connector Terminal
M98 7 Not existed
(+) (− ) Condition Reference value
Rear auxiliary input jacks
Connector Terminal
M98 7 Ground At rear AUX image is dis-
played on headrest display
unit.
SKIB2251J
Revision: 2010 May2011 QX56
Page 321 of 5598
AV
IMAGE SWITCH SIGNAL CIRCUITAV-173
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
IMAGE SWITCH SIGNAL CIRCUIT
DescriptionINFOID:0000000006216338
Image switch signal is input from headrest display unit to video distributor, according to rear seat remote controller operation.
When image switch signal is input from headrest displa y unit to video distributor, image output from AV con-
trol unit and image output from auxiliary input jacks switch.
Diagnosis ProcedureINFOID:0000000006216339
1.CHECK CONTINUITY IMAGE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect headrest display unit connector and video distributor connector.
3. Check continuity between headrest display unit har ness connector and video distributor harness connec-
tor.
*1: Headrest display unit LH
*2: Headrest display unit RH
4. Check continuity between headrest display unit harness connector and ground.
*1: Headrest display unit LH
*2: Headrest display unit RH
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VIDEO DISTRIBUTOR VOLTAGE
1. Connect headrest display unit connector and video distributor connector.
2. Turn ignition switch ON.
3. Check voltage between video distributor harness connector and ground.
Headrest display unit Video distributor Continuity
Connector Terminal Connector Terminal
B554
*120 M217 10 Existed
B574
*220 9 Existed
Headrest display unit GroundContinuity
Connector Terminal
B554
*120 Not existed
B574
*220
(+)
(− ) Condition Vo l ta g e
(Approx.)
Video distributor
Connector Terminal
Revision: 2010 May2011 QX56
Page 324 of 5598
AV-176
< DTC/CIRCUIT DIAGNOSIS >
DISK EJECT SIGNAL CIRCUIT
DISK EJECT SIGNAL CIRCUIT
DescriptionINFOID:0000000006216342
The eject signal is output to AV control unit when the eject switch of multifunction switch is pressed.
Diagnosis ProcedureINFOID:0000000006216343
1.CHECK CONTINUITY DISK EJECT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect multifunction switch c onnector and AV control unit connector.
3. Check continuity between multifunction switch harness connector and AV control unit harness connector.
4. Check continuity between multifunction switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Connect multifunction switch connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check voltage between AV control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace preset switch. Refer to AV-227, "Removal and Installation".
NO >> Replace AV control unit. Refer to AV-212, "
Removal and Installation".
Multifunction switch AV control unit
Continuity
Connector Terminal Connector Terminal
M72 14M20929 Existed
Multifunction switch GroundContinuity
Connector Terminal
M72 14 Not existed
(+) (− ) Condition Vo l ta g e
(Approx.)
AV c o n t r o l u n i t
Connector Terminal
M209 29 Ground Pressing the eject switch 0 V
Except for above 5.0 V
Revision: 2010 May2011 QX56
Page 325 of 5598
AV
MODE CHANGE SIGNAL CIRCUITAV-177
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
MODE CHANGE SIGNAL CIRCUIT
DescriptionINFOID:0000000006216344
AV control unit transmits the mode change signal to BOSE amp.
Driver's Audio Stage controls the speaker's output characte ristic by BOSE amp. so that the driver's seat is to
be the center of sounds.
Diagnosis ProcedureINFOID:0000000006216345
1.CHECK CONTINUITY MODE CHANGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connector and AV control unit connector.
3. Check continuity between BOSE amp. harness connector and AV control unit harness connector.
4. Check continuity between BO SE amp. harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK MODE CHANGE SIGNAL
1. Connect BOSE amp. connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check voltage between BOSE amp. harness connector and ground.
Is the inspection result normal?
YES >> Replace BOSE amp. Refer to AV-223, "Removal and Installation".
NO >> Replace AV control unit. Refer to AV-212, "
Removal and Installation".
AV control unit BOSE amp.
Continuity
Connector Terminal Connector Terminal
M209 30 B230 37 Existed
BOSE amp. GroundContinuity
Connector Terminal
B230 37 Not existed
(+) (− ) Condition Vo l ta g e
(Approx.)
BOSE amp.
Connector Terminal
B230 37 Ground Driver's Audio Stage ON. 0 V
Driver's Audio Stage OFF. 8.5 V
Revision: 2010 May2011 QX56
Page 328 of 5598
AV-180
< DTC/CIRCUIT DIAGNOSIS >
CAMERA IMAGE SIGNAL CIRCUIT
CAMERA IMAGE SIGNAL CIRCUIT
DescriptionINFOID:0000000006216348
Around view monitor control unit supplies to the front camera, rear camera and side camera. And then it
superimpose the images from each camera and outputs then to the front display unit.
Diagnosis ProcedureINFOID:0000000006216349
1.CHECK CONTINUITY CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front display unit connector and around view monitor control unit connector.
3. Check continuity between front display unit harne ss connector and around view monitor control unit har-
ness connector.
4. Check continuity between front display unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK CAMERA IMAGE SIGNAL
1. Connect front display unit connector and around view monitor control unit connector.
2. Turn ignition switch ON.
3. Check signal between front display unit harness connector and ground.
Is inspection result normal?
YES >> Replace front display unit. Refer to AV-212, "Removal and Installation".
NO >> Replace around view monitor control unit. Refer to AV-233, "
Removal and Installation".
Front display unitAround view monitor control
unit Continuity
Connector Terminal Connector Terminal
M215 8 M48 27 Existed
Front display unit GroundContinuity
Connector Terminal
M215 8 Not existed
(+) (− ) Condition Reference value
Front display unit
Connector Terminal
M215 8 Ground At camera image is dis-
played.
SKIB2251J
Revision: 2010 May2011 QX56
Page 329 of 5598
AV
FRONT CAMERA COMMUNICATION SIGNAL CIRCUITAV-181
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P
FRONT CAMERA COMMUNICATION SIGNAL CIRCUIT
DescriptionINFOID:0000000006216350
Around view monitor control unit supplies to the front camera, rear camera and side camera. And then it
superimpose the images from each camera and outputs then to the front display unit.
Superimpose the guiding lines, predictive course line and sonar indicator to the camera image that outputs
to the front display unit.
Around view monitor control unit performs the rec eption/transmission of communication signal with each
camera.
Diagnosis ProcedureINFOID:0000000006216351
1.CHECK CONTINUITY COMMUNI CATION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and front camera connector.
3. Check continuity between around view monitor c ontrol unit harness connector and front camera harness
connector.
4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK COMMUNICATION SIGNAL
1. Connect around view monitor control uni t connector and front camera connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES >> Replace around view monitor control unit. Refer to AV-233, "Removal and Installation".
NO >> Replace front camera. Refer to AV-234, "
Removal and Installation".
Around view monitor control
unit Front camera
Continuity
Connector Terminal Connector Terminal
M49 45 E50 6 Existed
Around view monitor control unit GroundContinuity
Connector Terminal
B49 45 Not existed
(+)
(− ) Condition Reference value
Around view monitor control
unit
Connector Terminal
M49 45 Ground “CAMERA” switch is ON or shift
position is “R”.
JSNIA0836GB
Revision: 2010 May2011 QX56
Page 330 of 5598
AV-182
< DTC/CIRCUIT DIAGNOSIS >
FRONT CAMERA IMAGE SIGNAL CIRCUIT
FRONT CAMERA IMAGE SIGNAL CIRCUIT
DescriptionINFOID:0000000006216352
Around view monitor control unit supplies to the front camera, rear camera and side came\
ra. And then itsuperimpose the images from each camera and outputs then to the front display unit.
Superimpose the guiding lines, predictive course line and sonar indicator to the camera image that outputs
to the front display unit.
Around view monitor control unit performs the rec eption/transmission of communication signal with each
camera.
Diagnosis ProcedureINFOID:0000000006216353
1.CHECK CONTINUITY FRONT CAMERA POWER SUPPLY AND GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and front camera connector.
3. Check continuity between around view monitor c ontrol unit harness connector and front camera harness
connector.
4. Check continuity between around view m onitor control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VOLTAGE FRONT CAMERA POWER SUPPLY
1. Connect around view monitor control unit connector and front camera connector.
2. Turn ignition switch ON.
3. Check voltage between around view m onitor control unit harness connector.
Is inspection result normal?
YES >> GO TO 3.
NO >> Replace around view monitor control unit. Refer to AV-233, "
Removal and Installation".
3.CHECK CONTINUITY FRONT CAMERA IMAGE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control unit connector and front camera connector.
3. Check continuity between around view monitor c ontrol unit harness connector and front camera harness
connector.
Around view monitor control
unit Front camera
Continuity
Connector Terminals Connector Terminals
M49 44
E50 2
Existed
46 1
Around view monitor control unit GroundContinuity
Connector Terminal
M49 46 Not existed
(+)
(− ) Condition Vo l ta g e
(Approx.)
Around view monitor control
unit
Connector Terminal
M49 46 Ground “CAMERA” switch is ON or
shift position is “R”.
6.0 V
Revision: 2010 May2011 QX56
Page 331 of 5598
AV
FRONT CAMERA IMAGE SIGNAL CIRCUITAV-183
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
J
K L
M B A
O P4. Check continuity between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 4.
NO >> Repair harness or connector.
4.CHECK FRONT CAMERA IMAGE SIGNAL
1. Connect around view monitor control uni t connector and front camera connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector.
Is inspection result normal?
YES >> Replace around view monitor control unit. Refer to AV-233, "Removal and Installation".
NO >> Replace front camera. Refer to AV-234, "
Removal and Installation".
Around view monitor control
unit Front camera
Continuity
Connector Terminals Connector Terminals
M49 41
E50 3
Existed
42 4
Around view monitor control unit GroundContinuity
Connector Terminals
M49 41, 42 Not existed
(+) ( −)
Condition Reference value
Around view monitor control unit
Connector Terminal Connector Terminal
M4941M4942 “CAMERA” switch is ON or
shift position is “R”.
JSNIA0834GB
Revision: 2010 May2011 QX56
Page 332 of 5598
AV-184
< DTC/CIRCUIT DIAGNOSIS >
REAR CAMERA COMMUNICATION SIGNAL CIRCUIT
REAR CAMERA COMMUNICATION SIGNAL CIRCUIT
DescriptionINFOID:0000000006216354
Around view monitor control unit supplies to the front camera, rear camera and side came\
ra. And then it
superimpose the images from each camera and outputs then to the front display unit.
Superimpose the guiding lines, predictive course line and sonar indicator to the camera image that outputs
to the front display unit.
Around view monitor control unit performs the rec eption/transmission of communication signal with each
camera.
Diagnosis ProcedureINFOID:0000000006216355
1.CHECK CONTINUITY COMMUNI CATION SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect around view monitor control un it connector and rear camera connector.
3. Check continuity between around view monitor control unit harness connector and rear camera harness connector.
4. Check continuity between around view m onitor control unit harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK COMMUNICATION SIGNAL
1. Connect around view monitor control unit connector and rear camera connector.
2. Turn ignition switch ON.
3. Check signal between around view monitor control unit harness connector and ground.
Is inspection result normal?
YES >> Replace around view monitor control unit. Refer to AV-233, "Removal and Installation".
NO >> Replace rear camera. Refer to AV-235, "
Removal and Installation".
Around view monitor control
unit Rear camera
Continuity
Connector Terminal Connector Terminal
M48 35 D164 4 Existed
Around view monitor control unit GroundContinuity
Connector Terminal
M48 35 Not existed
(+)
(− ) Condition Reference value
Around view monitor control
unit
Connector Terminal
M48 35 Ground “CAMERA” switch is ON or shift
position is “R”.
JSNIA0836GB
Revision: 2010 May2011 QX56