tow INFINITI QX56 2011 Factory Service Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2011, Model line: QX56, Model: INFINITI QX56 2011Pages: 5598, PDF Size: 94.53 MB
Page 92 of 5598
DOOR MIRROR REMOTE CONTROL SWITCHADP-83
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Comp onent Function CheckINFOID:0000000006248378
1.CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to ADP-83, "
CHANGEOVER SWITCH : Diagnosis Procedure".
CHANGEOVER SWITCH : Diagnosis ProcedureINFOID:0000000006248379
1.CHECK CHANGEOVER SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK CHANGEOVER SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check continuity between automatic drive posit ioner control unit harness connector and door mirror
remote control switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace harness.
Monitor item Condition
MIR CHNG SW-R/L When operating the changeover toward the right or left side. : ON
Other than the above. : OFF
(+)
(-)Voltage (V)
(Approx.)
Door mirror remote
control switch
Connector Terminal
M8 2
Ground 5
3
Automatic drive positioner control unit Door mirror remote control switch Continuity
Connector Terminal Connector Terminal
M75 2
M8 3
Existed
14 2
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M75 2
Not existed
14
Revision: 2010 May2011 QX56
Page 93 of 5598
ADP-84
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
3.CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror remo te control switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK CHANGEOVER SWITCH
Check door mirror remote control switch (changeover switch).
Refer to ADP-84, "
CHANGEOVER SWITCH : Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace door mirror remote control switch (changeover switch).
5.CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to GI-40, "
Intermittent Incident".
>> INSPECTION END
CHANGEOVER SWITCH : Component InspectionINFOID:0000000006248380
1.CHECK CHANGEOVER SWITCH
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Check continuity between door mirro r remote control switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace door mirror remote control switch.
MIRROR SWITCH
MIRROR SWITCH : Compon ent Function CheckINFOID:0000000006248381
1.CHECK MIRROR SWITCH FUNCTION
Check the operation on “MIR CON SW–UP/DN” and “MI R CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.
Door mirror remote control switch
GroundContinuity
Connector Terminal
M8 13 Existed
Door mirror remote control switch
Condition Continuity
Te r m i n a l
2 13 Changeover switch LEFT Existed
Other than the above Not existed
3 RIGHT Existed
Other than the above Not existed
Monitor item Condition
MIR CON SW-UP/DN When operating the mirror switch toward the up or down side. : ON
Other than the above. : OFF
Revision: 2010 May2011 QX56
Page 94 of 5598
DOOR MIRROR REMOTE CONTROL SWITCHADP-85
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to ADP-85, "
MIRROR SWITCH : Diagnosis Procedure".
MIRROR SWITCH : Diagnosis ProcedureINFOID:0000000006248382
1.CHECK MIRROR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect door mirror remote control switch connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK MIRROR SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check continuity between automatic drive posit ioner control unit harness connector and door mirror
remote control switch harness connector.
4. Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace automatic drive positioner control unit.
NO >> Repair or replace harness.
3.CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
MIR CON SW-RH/LH When operating the mirror switch toward the right or left side. : ON
Other than the above. : OFF
Monitor item Condition
(+)
(-)Voltage (V)
(Approx.)
Door mirror remote
control switch
Connector Terminal
M8 4
Ground 5
5
6
14
Automatic drive positioner control unit Door mirror remote control switch Continuity
Connector Terminal Connector Terminal
M75 3
M8 6
Existed
45
15 14
16 4
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M75 3
Not existed
4
15
16
Revision: 2010 May2011 QX56
Page 524 of 5598
![INFINITI QX56 2011 Factory Service Manual
PRECAUTIONSBRC-7
< PRECAUTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
and tires installed on the vehicle are the specified si ze and parts. Brake performance and controllability may
be negativ](/img/42/57033/w960_57033-523.png "INFINITI QX56 2011 Factory Service Manual
PRECAUTIONSBRC-7
< PRECAUTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
and tires installed on the vehicle are the specified si ze and parts. Brake performance and controllability may
be negativ")
PRECAUTIONSBRC-7
< PRECAUTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
and tires installed on the vehicle are the specified si ze and parts. Brake performance and controllability may
be negatively affected when other parts than the specified are installed.
Brake stopping distance may become longer and steering stability may be negatively affected, when tires in
different size and combination or other parts than the specified are used.
When a radio (including wiring), antenna and antenna lead line are located near ABS actuator and electric
unit (control unit), a malfunction or improper operation ma y occur for the control of VDC function, TCS func-
tion, ABS function, EBD function, hill start assist func tion or brake limited slip differential (BLSD) function.
When the following items are replaced by other parts than genuine parts or modified, ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, and the control may not operate normally for VDC
function, TCS function, ABS function, EB D function, hill start assist function or brake limited slip differential
(BLSD) function.
- Suspension component parts (shock absorber, spring, bushing and others)
- Tire and wheel (other than the specified size)
- Brake component parts (brake pad, disc rotor, brake caliper and others)
- Engine component parts (ECM, muffler and others)
- Body reinforcement component parts (rollover bar, tower bar and others)
When suspension, tire and brake component parts are excessively worn or deteriorated and the vehicle is
driven, ABS warning lamp, brake warning lamp and VDC warning lamp may tu\
rn ON, and the control may
not operate normally for VDC function, TCS function, ABS function, EBD function, hill start assist function or
brake limited slip differential (BLSD) function.
ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, when only front wheel or rear wheel is rotated using a free roller. This is not a ma lfunction, because it is caused by wheel speed difference
between wheel that is rotated and wheel that is not rota ted. In this case, perform self-diagnosis, check self-
diagnosis results, and erase memory.
When power supply voltage is not normal, ABS warning lamp, brake warning lamp and VDC warning lamp
turn ON. ABS actuator and electric unit (control unit) st ops control for VDC function, TCS function, ABS func-
tion, EBD function, hill start assist function or brake limited slip differential (BLSD) function. Ordinary brake
operates. After power supply returns to normal, ABS warning lamp, brake warning lamp and VDC warning
lamp turn OFF. The control becomes operative for VD C function, TCS function, ABS function, EBD function,
hill start assist function or brake li mited slip differential (BLSD) function.
VDC warning lamp may turn ON and VDC function or TCS function may not normally operate, when driving
on a special road the is extremely slanted (bank in a circ uit course). This is not a malfunction if the status
returns to normal for VDC function or TCS function after the engine is started again. In this case, perform
self-diagnosis, check self-diagnosis results, and erase memory.
A malfunction in yaw rate/side/decel G sensor syste m may be detected when the vehicle sharply turns dur-
ing a spin turn, acceleration turn or drift driving while VDC function or TCS function are OFF (VDC OFF
switch is pressed and VDC OFF indicator lamp is in ON st atus). This is not a malfunction if the status returns
to normal for VDC function or TCS function after the engine is started again. In this case, perform self-diag-
nosis, check self-diagnosis results, and erase memory
Precaution for Harness RepairINFOID:0000000006222558
Solder the repair part, and wrap it with tape. [Twisted wire fray must be 110 mm (4.33 in) or less.]
SKIB8766E
Revision: 2010 May2011 QX56
Page 532 of 5598
![INFINITI QX56 2011 Factory Service Manual
COMPONENT PARTSBRC-15
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Downsize and weight reduction is aimed. IC for detection portion and magnet for sensor rotor are adopted.
](/img/42/57033/w960_57033-531.png "INFINITI QX56 2011 Factory Service Manual
COMPONENT PARTSBRC-15
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Downsize and weight reduction is aimed. IC for detection portion and magnet for sensor rotor are adopted.
")
COMPONENT PARTSBRC-15
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Downsize and weight reduction is aimed. IC for detection portion and magnet for sensor rotor are adopted.
Power supply is supplied to detection portion so that magnetic field
line is read. Magnetic field that is detected is converted to current
signal.
When sensor rotor rotates, magnetic field changes. Magnetic field
change is converted to current signals (rectangular wave) and is
transmitted to ABS actuator and electric unit (control unit). Change
of magnetic field is pr oportional to wheel speed.
Stop Lamp SwitchINFOID:0000000006222563
Detects the operation status of brake pedal and transmits converted electric signal to ABS actuator and elec-
tric unit (control unit).
Steering Angle SensorINFOID:0000000006222564
Detects the following information and transmits steering angle signal to ABS actuator and electric unit (control
unit) via CAN communication.
Steering wheel rotation amount
Steering wheel rotation angular velocity
Steering wheel rotation direction
Yaw Rate/Side/Decel G sensorINFOID:0000000006222565
Calculates the following information that affects the v ehicle and transmits a signal to ABS actuator and electric
unit (control unit) via communication lines.
Vehicle rotation angular velocity (yaw rate signal)
Vehicle lateral acceleration (side G signal) / longitudinal acceleration (decel G signal)
Brake Fluid Level SwitchINFOID:0000000006222566
Detects the brake fluid level in reservoir tank and trans mits converted electric signal from ABS actuator and
electric unit (control unit), when brake fluid level is the specified level or less.
Parking Brake SwitchINFOID:0000000006222567
Detects the operation status of parking brake switch and transmits converted electric signal from combination
meter to ABS actuator and electric unit (control unit).
VDC OFF SwitchINFOID:0000000006222568
VDC OFF switch is integrated in SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
The operation of the VDC OFF switch enables the arbi trary switching of the VDC function between stop sta-
tus and standby status. The status of the function is indicated by the VDC OFF indicator lamp. (ON: Non-
operational status, OFF: Standby status)
- VDC function NOTE:
Brake limited slip differentia l (BLSD) control operates.
- TCS function
VDC OFF indicator lamp turns OFF (standby status) when the engine is started again after it is stopped once while VDC OFF indicator lamp is ON (non-operational status).
JPFIC0131GB
Revision: 2010 May2011 QX56
Page 547 of 5598
![INFINITI QX56 2011 Factory Service Manual
BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal](/img/42/57033/w960_57033-546.png "INFINITI QX56 2011 Factory Service Manual
BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal")
BRC-30
< SYSTEM DESCRIPTION >[WITH VDC]
SYSTEM
Major signal transmission between each unit via communication lines is shown in the following table.
*1: Communication line between yaw rate/side/decal G s
ensor and ABS actuator and electric unit (control unit)
*2: Models with 4WD system
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
During a cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer side of turn. Moment directing towards the outer side of turn is generated. Oversteer is prevented.
Changing driving lane on a slippery road, when oversteer tendency is judged large, engine output is con- trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
VDC Function That Prevents Understeer Tendency
Component Signal description
Yaw rate/side/decel G sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via com-
munication line
*1.
Yaw rate signal
Side G sensor signal
Decel G sensor signal
ECM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
Accelerator pedal position signal
Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
Target throttle position signal
TCM Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
Shift position signal
Transfer control unit
*2Mainly transmits the following si gnals to ABS actuator and electric unit (control unit) via CAN
communication.
Current 4WD mode signal
Steering angle sensor Mainly transmits the following si
gnals to ABS actuator and electric unit (control unit) via CAN
communication.
Steering angle sensor signal
Combination meter Mainly receives
the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
VDC warning lamp signal
VDC OFF indicator lamp
JPFIC0135GB
JPFIC0136GB
Revision: 2010 May2011 QX56
Page 548 of 5598
![INFINITI QX56 2011 Factory Service Manual
SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side o](/img/42/57033/w960_57033-547.png "INFINITI QX56 2011 Factory Service Manual
SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side o")
SYSTEMBRC-31
< SYSTEM DESCRIPTION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
During a cornering, brake force (brake fluid pressu re) is applied on front wheel and rear wheel on the inner
side of turn. Moment directing towards the inner side of turn is generated. Understeer is prevented.
Applying braking during a cornering on a slippery road, when understeer tendency is judged large, engine
output is controlled as well as brake force (brake fluid pressure) of four wheels. Understeer tendency
decreases.
TCS FUNCTION
TCS FUNCTION : System DescriptionINFOID:0000000006222573
Wheel spin status of drive wheel is detected by wheel sensor of 4
wheels. Engine output and transmission shift status is controlled
so that slip rate of drive wheels is in appropriate level. When wheel
spin occurs on drive wheel, ABS ac tuator and electric unit (control
unit) perform brake force control of LH and RH drive wheels (apply
brake force by increasing brake fluid pressure of drive wheel) and
decrease engine torque by engine torque control. Wheel spin
amount decreases. Engine torque is controlled to appropriate
level.
TCS function can be switched to non-operational status (OFF) by
operating VDC OFF switch. In this case, VDC OFF indicator lamp
turns ON.
TCS function is not operate when 4WD mode is “4L”. (Models with
4WD system)
VDC warning lamp blinking while TCS function is in operation and indicates to the driver that the function is in operation.
Slight vibrations are felt on the brake pedal and the operation noises occur, when TCS function operates. This is not a malfunc-
tion because it is caused by TCS function that is normally oper-
ated.
CONSULT-III can be used to diagnose the system diagnosis.
Fail-safe function is adopted. W hen a malfunction occurs in TCS
function, the control is suspended for VDC function, TCS function,
hill start assist function and brake limited slip differential (BLSD)
function. The vehicle status becomes the same as models without VDC function, TCS function, hill start
assist function and brake limited slip differential (B LSD) function. However, ABS function and EBD function
are operated normally. Refer to BRC-25, "
Fail-safe".
SYSTEM DIAGRAM
NOTE:
JPFIC0137GB
JPFIC0138GB
JPFIC0139GB
Revision: 2010 May2011 QX56
Page 636 of 5598
![INFINITI QX56 2011 Factory Service Manual
VDC OFF SWITCHBRC-119
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC OFF SWITCH
Component Function CheckINFOID:0000000006222646
1.CHECK VDC OFF SWITCH OPERATION
Check that](/img/42/57033/w960_57033-635.png "INFINITI QX56 2011 Factory Service Manual
VDC OFF SWITCHBRC-119
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC OFF SWITCH
Component Function CheckINFOID:0000000006222646
1.CHECK VDC OFF SWITCH OPERATION
Check that")
VDC OFF SWITCHBRC-119
< DTC/CIRCUIT DIAGNOSIS > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
VDC OFF SWITCH
Component Function CheckINFOID:0000000006222646
1.CHECK VDC OFF SWITCH OPERATION
Check that VDC OFF indicator lamp in combinati on meter turns ON/OFF when VDC OFF switch is operated.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Proceed to diagnosis procedure. Refer to BRC-119, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006222647
NOTE:
VDC OFF switch is integrated in SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
1.CHECK VDC OFF SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Disconnect SNOW MODE / TOW MODE / VDC OFF s witch assembly (2WD models) or 4WD switch
assembly (4WD models) harness connector.
4. Check continuity between ABS actuator and elec tric unit (control unit) harness connector and SNOW
MODE / TOW MODE / VDC O FF switch assembly (2WD models) or 4WD switch assembly (4WD models)
harness connector.
*1: SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models)
*2: 4WD switch assembly (4WD models)
5. Check continuity between ABS actuator and electr ic unit (control unit) harness connector terminal and
ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK VDC OFF SW ITCH GROUND CIRCUIT
Check continuity between SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or 4WD
switch assembly (4WD models) harness connector terminal and ground.
*1: SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models)
*2: 4WD switch assembly (4WD models)
ABS actuator and electric unit (control unit)SNOW MODE / TOW MODE / VDC OFF
switch assembly (2WD models) or 4WD switch assembly (4WD models) Continuity
Connector Terminal Connector Terminal
E36 39 M147
*1
M54*21 Existed
ABS actuator and electric unit (control unit) —Continuity
Connector Terminal
E36 39 Ground Not existed
SNOW MODE / TOW MODE / VDC
OFF switch assembly (2WD models) or 4WD switch assembly (4WD models) —Continuity
Connector Terminal M147
*1
M54*220 Ground Existed
Revision: 2010 May2011 QX56
Page 637 of 5598
![INFINITI QX56 2011 Factory Service Manual
BRC-120
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
VDC OFF SWITCH
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK VDC OFF SWITCH
Check VDC OFF switch.](/img/42/57033/w960_57033-636.png "INFINITI QX56 2011 Factory Service Manual
BRC-120
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
VDC OFF SWITCH
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK VDC OFF SWITCH
Check VDC OFF switch.")
BRC-120
< DTC/CIRCUIT DIAGNOSIS >[WITH VDC]
VDC OFF SWITCH
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK VDC OFF SWITCH
Check VDC OFF switch. Refer to BRC-120, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace VDC OFF switch. Refer to BRC-140, "
Removal and Installation".
4.CHECK VDC OFF SWITCH SIGNAL
With CONSULT-III.
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or 4WD switch assem-
bly (4WD models) harness connector.
3. Select “ABS”, “DATA MONITOR” and “OFF SW” accord ing to this order. Check VDC OFF switch signal.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 5.
5.CHECK TERMINAL
Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Check SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or 4WD switch assembly (4WD models) pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> Replace ABS actuator and electr ic unit (control unit). Refer to BRC-137, "Removal and Installa-
tion".
NO >> Repair or replace error-detected parts.
Component InspectionINFOID:0000000006222648
NOTE:
VDC OFF switch is integrated in SNOW MODE / TOW MODE / VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
1.CHECK VDC OFF SWITCH
1. Turn the ignition switch OFF.
2. Disconnect SNOW MODE / TOW MODE / VDC OFF s witch assembly (2WD models) or 4WD switch
assembly (4WD models) harness connector.
3. Check continuity between terminals of SNOW MO DE / TOW MODE / VDC OFF switch assembly (2WD
models) or 4WD switch assembly (4WD models) connector.
Is the inspection result normal?
YES >> INSPECTION END
Condition DATA MONITOR
When VDC OFF switch is pressed and VDC OFF indicator
lamp in combination meter is in ON status On
When VDC OFF switch is pressed and VDC OFF indicator
lamp in combination meter is in OFF status Off
SNOW MODE / TOW MODE / VDC OFF
switch assembly (2WD models) or 4WD switch assembly (4WD models) Condition Continuity
Terminal
1 – 20 When VDC OFF switch is pressed Existed
When VDC OFF switch is not pressed Not existed
Revision: 2010 May2011 QX56
Page 652 of 5598
![INFINITI QX56 2011 Factory Service Manual
WHEEL SENSORBRC-135
< REMOVAL AND INSTALLATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Never twist front wheel sensor harness when installi ng front wheel sensor. Check that grommet is fully](/img/42/57033/w960_57033-651.png "INFINITI QX56 2011 Factory Service Manual
WHEEL SENSORBRC-135
< REMOVAL AND INSTALLATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Never twist front wheel sensor harness when installi ng front wheel sensor. Check that grommet is fully")
WHEEL SENSORBRC-135
< REMOVAL AND INSTALLATION > [WITH VDC]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Never twist front wheel sensor harness when installi ng front wheel sensor. Check that grommet is fully
inserted to bracket. Check that front wheel sensor harness is not twisted after installation.
Check that front wheel sensor identificat ion line face toward the vehicle rear.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded ViewINFOID:0000000006222672
CAUTION:
Replace wheel hub and bearing assembly as an assem bly when replacing because wheel sensor can-
not be disassembled.
NOTE:
Rear RH wheel sensor is symmetrically opposite of LH.
REAR WHEEL SENSOR : Re moval and InstallationINFOID:0000000006222673
CAUTION:
Replace wheel hub and bearing assembly as an assem bly when replacing because wheel sensor can-
not be disassembled.
REMOVAL
Remove wheel hub and bearing assembly. Refer to RAX-7, "Removal and Installation".
CAUTION:
Never twist or pull rear wheel sensor harness.
INSTALLATION
Note the following, and install in the reverse order of the removal.
Never twist rear wheel sensor harness when installing rear wheel sensor. Check that grommet is fully inserted
to bracket. Check that rear wheel sensor harness is not twisted after installation.
1. Rear LH wheel sensor harness con-
nector 2. Rear LH wheel sensor 3. Bracket
: Vehicle front
Refer to GI-4, "
Components" for symbols in the figure.
JPFIC0200GB
Revision: 2010 May2011 QX56