speaker ISUZU KB P190 2007 Workshop User Guide

CAB 10-11
DISASSEMBLY




This illustration is based on RHD model

RTW 4A0LF000701
Disassembly Steps
▲ 1 . Switch bezel/W indow regulator handle
▲ 2. Power window switch
▲ 3. Bezel
▲ 4. Door mirror cover
▲ 5. Door trim panel
▲ 6. Tweeter (Required Option)
▲ 7. Door mirror assembly
▲ 8. Outer waste seal
▲ 9. Bracket
▲ 10. Speaker assembly
▲ 11 . W aterproof sheet
▲ 12. Inside lever
▲ 13. W indow glass
▲ 14. W indow regulator/Power window
regulator

▲
15. Glass run
▲ 16. Glass run rear channel / Glass ran rear
channel with Door lock control or Anti
theft (European Countries)
▲ 17. Door lock assembly/Door lock assembly
with super lock
▲ 18. Outside handle protector (EUROPE)
▲ 19. Outside handle
▲ 20. Door lock cylinder protector (EUROPE)
▲ 21. Door lock cylinder / Door lock cylinder
with door lock switch (European
Countries)
22. Door harness assembly
23. Anti rattler


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-13


• Remove the 2 screws and pull out the trim panel at the 8
clip positions (W indow regulator handle type).
RTW 3A0SH00070 1

6. Tweeter (Required option)
• Disconnect the tweeter harness connector and remove
the 3 screws.


7. Door Mirror Assembly
• Remove 3 fixing bolts and then remove the connector.
8. Outer Waste Seal


9. Bracket
10. Speaker Assembly • Remove the fixing screw and then remove the
connector.
11. Waterproof Sheet • Take care not to damage the sheet when peeling it off.
12. Inside Lever • Disconnect the door lock cables.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-15
REASSEMBLY




This illustration is based on RHD model

RTW 4A0LF000801

Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Door lock cylinder / Door lock cylinder
with door lock switch (European
Countries)
▲ 4. Door lock cylinder protector (EUROPE)
▲ 5. Outside handle
▲ 6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (European Countries)
9. Glass run
10. W indow regulator / Power window regulator
▲ 11. W indow glass
12. Inside lever
13. W aterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch
▲ 23. Switch bezel / W indow regulator handle

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-21
DISASSEMBLY




10
11
15
14
16
7
13
3
4
5
1
2
9
6 8
12
1

RTW 7A0LF000901

Disassembly Steps
▲
1. Power window switch/W indow regulator
handle
▲ 2. Bezel
▲ 3. Door trim panel
▲ 4. Bracket
▲ 5. Speaker assembly
▲ 6. W aterproof sheet
▲ 7. Inside lever
▲ 8. Outer waste seal

▲
9. Glass run rear channel
▲ 10. W indow glass
▲ 11. W indow regulator/Power window
regulator
▲ 12. Glass run
▲ 13. Door lock assembly
▲ 14. Outside handle
15. Door harness assembly
16. Anti rattler


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-23

4. Bracket
5. Speaker assembly • Remove the fixing bolt and then remove the connector.
6. Waterproof Sheet • Take care not to damage the sheet when peeling it off.
7. Inside Lever • Disconnect the door lock cables.
8. Outer Waste Seal
9. Glass Run Rear Channel • Remove the bolt.

10. Window Glass
• Remove 2 bolts through the access hole and pull out the
window glass upward.

11. Window Regulator/Power Window Regulator
• Remove the 5 fixing bolts.
• Disconnect the power window motor connector.
12. Glass Run • Pull it out from the door frame of the channel.
13. Door Lock Assembly • Disconnect the lock cable from the anti rattler.
• Remove the 3 fixing screws and the bolt.
• Disconnect the linkage and harness connector.
14. Outside Handle • Remove the 2 fixing bolts.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

10-24 CAB
REASSEMBLY



7
6
2
3
1
10 4
14
13
11
12
16
15
8
9 5
16

RTW 7A0LF001001


Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Outside handle
4. Door lock assembly
5. Glass run
6. W indow regulator/Power window regulator
7. W indow glass
8. Glass run rear channel

9. Outer waste seal
10. Inside lever
11. W aterproof sheet
12. Speaker assembly
13. Bracket
14. Door trim panel
15. Bezel
▲ 16. Power window switch/W indow regulator
handle

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-45
INTERIOR TRIM PANELS
REMOVAL AND INSTALLATION



RTW 3A0MF001301

Extend Cab Model
Removal Steps
1. Sill plate
2. Dash side trim cover
▲ 3. Front pillar trim cover
▲ 4. Rear upper cushion
5. Jack cover
▲ 6. Rear end trim cover
▲ 7. Rear speaker grille/Rear speaker
▲ 8. Body side rear lower trim cover
9. Door finisher
▲ 10. Tongue side seat belt
▲ 11. Body side rear upper trim cover


Installation Steps
11. Body side rear upper trim cover
▲ 10. Tongue side seat belt
9. Door finisher
8. Body side rear lower trim cover
7. Rear speaker grille/Rear speaker
▲ 6. Rear end trim cover
5. Jack cover
4. Rear upper cushion
3. Front pillar trim assembly
2. Dash side trim cover
1. Sill plate



BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

10-46 CAB

RTW 710SH000501
Important Operations - Removal
3. Front Pillar Trim Cover • Turn up the finisher and pry the trim cover clips free
from the body panel.
Remove the trim cover by pulling upward on the lowe
r
part of it.



RTW 5A0SH000601
4. Rear Upper Cushion
• Slide the upper cushion upward to remove it.
6. Rear End Trim Cover • Pry the trim cover clips free from the body panel, and
slide the trim cover upward to remove it.

7. Rear Speaker Grille/Rear Speaker
1) Remove the rear speaker grille (1).
2) Remove the 3 screws fixing the rear speaker (2) and disconnect the connector (3).

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007