window ISUZU KB P190 2007 Workshop Workshop Manual

10-16 CAB




Important Operations
3. Door Lock Cylinder • Tighten the door lock cylinder fixing bolts to the specified
torque.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
9 (0.9/78)

4. Door Lock Cylinder Protector (EUROPE)
• Tighten the door lock cylinder protector fixing bolt to the
specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
9 (0.9/78)



5. Outside Handle
• Tighten the outside handle fixing bolts to the specified
torque.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
9 (0.9/78)


6. Outside Handle Protector (EUROPE)
• Tighten the outside handle protector fixing bolt to the
specified torque.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
9 (0.9/78)



11. Window Glass
• Insert the window glass into position by tilting it as
necessary, then set it against the channel of the windo
w
regulator.



•

Attach the window glass to the window regulator with the
2 bolts.


BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-17

23. Window Regulator Handle
• Install the regulator handle as illustrated when closing
the window glass.



BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-21
DISASSEMBLY




10
11
15
14
16
7
13
3
4
5
1
2
9
6 8
12
1

RTW 7A0LF000901

Disassembly Steps
▲
1. Power window switch/W indow regulator
handle
▲ 2. Bezel
▲ 3. Door trim panel
▲ 4. Bracket
▲ 5. Speaker assembly
▲ 6. W aterproof sheet
▲ 7. Inside lever
▲ 8. Outer waste seal

▲
9. Glass run rear channel
▲ 10. W indow glass
▲ 11. W indow regulator/Power window
regulator
▲ 12. Glass run
▲ 13. Door lock assembly
▲ 14. Outside handle
15. Door harness assembly
16. Anti rattler


BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

10-22 CAB

1
RTW 7A0SH000401

Important Operations
1. Power Window Switch/Window Regulator Handle • Remove the 2 screws (1) and pry out the power windo
w
switch and disconnect the connector.



• To remove the regulator handle, remove the clip at the
root of the handle using a wire.

2. Bezel
• Remove the screw.





RTW 7A0SH000501

3. Door Trim Panel
• Pull out the trim panel at the 7 clip positions (Powe
r
window type).
• Remove the 2 screws and pull out the trim panel at the 7
clip positions (W indow regulator handle type).

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-23

4. Bracket
5. Speaker assembly • Remove the fixing bolt and then remove the connector.
6. Waterproof Sheet • Take care not to damage the sheet when peeling it off.
7. Inside Lever • Disconnect the door lock cables.
8. Outer Waste Seal
9. Glass Run Rear Channel • Remove the bolt.

10. Window Glass
• Remove 2 bolts through the access hole and pull out the
window glass upward.

11. Window Regulator/Power Window Regulator
• Remove the 5 fixing bolts.
• Disconnect the power window motor connector.
12. Glass Run • Pull it out from the door frame of the channel.
13. Door Lock Assembly • Disconnect the lock cable from the anti rattler.
• Remove the 3 fixing screws and the bolt.
• Disconnect the linkage and harness connector.
14. Outside Handle • Remove the 2 fixing bolts.

BACK TO CHAPTER INDEX
TO MODEL INDEX
ISUZU KB P190 2007

10-24 CAB
REASSEMBLY



7
6
2
3
1
10 4
14
13
11
12
16
15
8
9 5
16

RTW 7A0LF001001


Reassembly Steps
1. Anti rattler
2. Door harness assembly
▲ 3. Outside handle
4. Door lock assembly
5. Glass run
6. W indow regulator/Power window regulator
7. W indow glass
8. Glass run rear channel

9. Outer waste seal
10. Inside lever
11. W aterproof sheet
12. Speaker assembly
13. Bracket
14. Door trim panel
15. Bezel
▲ 16. Power window switch/W indow regulator
handle

BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007

CAB 10-25
Important Operations
3. Outside Handle • Tighten the outside handle fixing bolts to the specified
torque.
Torque N ⋅m (kgf ⋅m/lb ⋅in)
9 (0.9/78)


16. Window Regulator Handle
• Install the regulator handle as illustrated when closing
the window glass.



BACK TO CHAPTER INDEX TO MODEL INDEX
ISUZU KB P190 2007