ISUZU TF SERIES 2004 Workshop Manual

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-21

Diagnostic Trouble Codes
The purpose of the “Diagnostic Trouble Codes" mode is
to display stored TCM trouble codes.
When “Diagnostic Trouble Codes" is selected an
“ Application Menu" screen appears.
Clear DTC Information
The purpose of the “Clear DTC Information" mode is to
command the clearing of stored TCM trouble codes.
When “Clear DTC Information" is selected, a “Clea
r
DTC Information", warning screen appears. This screen
informs you that by cleaning DTC's, “all stored DTC
information in controller will be erased".
Do you want to clear DTC's (Yes/No).
Press either the Yes or No key when answering.
After clearing codes, confirm system operation by test
driving the vehicle.
Allow the vehicle to shift through all four forward gears
in a manner which attempts to repeat the failure
condition.
NOTE: When the trouble has not been repaired and
the trouble code cannot be erased, check the vehicle
again.
DTC Information
When “DTC Information" is selected, an “Application
Menu" appears with a list of DTC information function
keys addressing DTC specifics and their origins.
Function key selections may vary for particular vehicle
and/or system.
Data Display
The purpose of the “Data Display" mode is to
continuously monitor data parameters.
The current actual values of all important sensors and
signals in the system are display through F1 mode.
When “Data Display" is selected an “Application Menu"
appears. Please select either “Engine" or “Transmission
Data Display".
See “Transmission Data" on next page.
Snapshot
When “Snapshot" is selected an “Application Menu"
appears.
When “Transmission Snapshot" application is selected
from the “Application Menu", a “Snapshot Menu"
appears, displaying several options. “Snapshot" options
may vary from one system to another.
“ Snapshot" allows a recording of all vehicle parameters.
There parameters may then be replayed at a future
point in time.
This action allows you to focus on making the condition
occur, rather than trying to view all of the data in
anticipation of the fault. The snapshot will collect
parameter information around a trigger point that you
select.

When a snapshot is taken. It is recorded onto the
PCMCIA memory card. When the Tech 2 is powered
down. Snapshots are not lost.
Actuator Tests
The purpose of “Actuator Tests" mode is to check fo
r
correct operation of electronic system actuators.
Lamps
You can operate the lamps by pressing the “ON" and
“ OFF" buttons.
Preconditions: none
Solenoid
Solenoid A(S1), Solenoid B(S2)
You can operate the solenoids by pressing the “ON"
and “OFF" buttons.
Preconditions: P –N position, no vehicle speed, no
engine speed
Pressure Control Solenoid (PCS)
You can set desired PCS Current using the “ON" (+20)
and “OFF" (-20) button. The PC Solenoid Data informs
about PCS Current, Pressure and Duty Cycle.
Preconditions: P –N position, no engine speed, no
vehicle speed
NOTE: Freeze Frame
Freeze Frame is an element of the Diagnostic
Management System which stores various vehicle
information at the moment an emission-related fault
is stored in memory and when the Check Transe
Lamp is commanded on. These data can help to
identity the cause of a fault. Refer to Storing An
d
Erasing Freeze Frame Data for more detaile
d
information.

7A2-22 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

TRANSMISSION DATA
ITEM UNIT ENGIN RUNNING AT IDLE
Current Gear 1 st/2 nd/3 rd/4 th 1 st
Target Gear 1 st/2 nd/3 rd/4 th 1 st
Vehicle Speed km/h 0 km/h
AT Output Speed (Automatic Transmission) RPM 0 RPM
AT Input Speed (Automatic Transmission) RPM 675725 RPM
Engine Speed RPM 675725 RPM
Throttle Position Sensor Signal % 0.007.00%
AT Oil Temperature (Automatic Transmission) C Depends on conditions
TCM Status Transfer Low /Transfer High Transfer HI
Desired PC Solenoid Pressure (STH) kPa 34.397.0 kPa
Desired PC Solenoid Current (STH) mA 8351020 mA
PC Solenoid Actual Current (STH) mA 8351020 mA
Gear Ratio : 1 Depends on uper hood
TCC Slip Speed RPM 0 RPM
Shift Position Actual P/R/N/L/2/3 P
Inhibitor Switch P/R/N/L/2/3 P
Transmission Check Light On/Off Off
AT Oil Temperature Lamp (Automatic
Transmission) On/Off Off
3 rd Start Lamp On/Off Off
Power Lamp On/Off Off
Shift Solenoid S1 On/Off On
Shift Solenoid S2 On/Off On
Shift Solenoid S3 On/Off Off
Diag Switch Condition On/Off Off
Power Switch On/Off Off
Brake Switch On/Off Off
Cruise Switch On/Off Off
4L Signal On/Off Off
3 rd Start Switch On/Off Off
Coolant Temperature C Depends on conditions
Torque Request (timing Retard) CA 0 CA
Garage Shift Mode On/Off Off
CAN TPS % 0.00%
CAN Signal Valid Counter (ECM)
— 0  255
CAN Signal Valid Counter (TCM) — 0  255

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-23

SNAPSHOT DISPLAY WITH TIS2000



Procedures for transferring and displaying Tech2
snapshot data by using TIS2000 [Snapshot Upload]
function is described below.
Snapshot data can be displayed with [Snapshot
Upload] function included in TIS2000.
By analyzing these data in various methods, trouble
conditions can be checked.
Snapshot data is displayed by executing the three steps
below shown:

1. Record the snapshot data, in Tech2.

2. Transfer the snapshot data to PC.

7A2-24 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

After recording the snapshot in Tech2, transfer the data
from Tech2 to PC by the below procedures.
1.
Start TIS2000.
2.
Select [Snapshot Upload] on the TIS2000 start
screen.
3.
Select [Upload from trouble diagnosis tool
(transfer from diagnosis tester)] or click the
corresponding icon of the tool bar.
4.
Select Tech2, and transfer the recorded snapshot
information.
5.
Select the transferred snapshot.
6.
After ending transfer of the snapshot, data
parameter list is displayed on the screen.
3. Snapshot data is displayed with TIS2000
[Snapshot Upload] function.
Snapshot is stored in the PC hard disk or floppy disk,
and can be displayed any time.
Stored snapshot can be displayed by the below
procedures.
1.
Start TIS2000.
2.
Select [Snapshot Upload] on the TIS2000 start
screen.
3.
Select [Open the existing files] or click the
corresponding icon of the tool bar.
4.
Select the transferred snapshot.
5.
Open the snapshot, to display the data paramete
r
list on the screen.

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-25

Graph display Values and graphs (Max. 3 graphs):



1.
Click the icon for graph display. [Graph
Parameter] window opens.
2.
Click the first graph icon of the window upper part,
and select one parameter from the list of the
window lower part. Selected parameter is
displayed nest to the graph icon. Graph division
can be selected in the field on the parameter right
side.
3.
Repeat the same procedures with the 2nd and 3rd
icons.
4.
After selecting all parameters to be displayed
(Max. 3 parameters), click [OK] button.
5.
Parameter selected is displayed in graph form on
the right of the data parameter on the screen.
6.
Graph display can be moved with the navigation
icon.

7.
For displaying another parameter by graph, click
the parameter of the list, drug the mouse to the
display screen while pressing the mouse button
and release the mouse button. New parameter is
displayed at the position of the previous
parameter. For displaying the graph display screen
in full size, move the cursor upward on the screen.
When the cursor is changed to the magnifying
glass form, click the screen. Graph screen is
displayed on the whole screen.

7A2-26 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Display of graphs on one screen (Max. 6 graphs):



1.
Click the 6 graph icon. [Graph Parameter] window
opens.
2.
Click the graph icon, select the parameter to be
displayed from the list and change divisions
according to necessity.
3.
Repeat the same procedures with the graph icons,
from the 2nd to 6th.
4.
Click the [OK] button to display.
5.
In this case, parameters are displayed only in
graph form. All parameters are displayed in one
graph.
6.
The graph display screen can be moved with the
navigation icon.

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-27

SERVICE PROGRAMMING SYSTEM (SPS)
The procedure to program the control unit by using the
Service Programming System (SPS) software
contained in TIS2000 is explained below.
NOTE:






Should Tech2 display "SPS Procedure was not
successful", engine will not start, but no DTCs
are present, low battery voltage or poo
r
electrical connections should be the primary
suspects. Perform the SPS procedure again
after rectifying the fault/s.


IMPORTANT:
Perform the following checks before attempting to
program the control unit:







The Tech2 PCMCIA card is programmed with
the latest software release.







The latest release of TIS2000 is loaded on the
PC.







The vehicle battery is fully charged.







The control unit to be programmed is
connected to the vehicle.
1. Preparations of TIS 2000
1.
Connect Tech 2 to P/C.
2.
Check to see if Hardware Key is plugged into Port.
3.
Activate TIS 2000 by P/C.
4.
On the activating screen of TIS2000, choose
"Service Programming System"





5.
On the screen of "Diagnostic Tester and
Processing Program Selection", choose the one
that will comply with the following.

Diagnostic tester in use

New programming by the existing module or new
programming by the replaced/new module.

Fixing position of the control unit.
6.
Upon completion of the selection, push the button
of "Continue".

7A2-28 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

2.Demand of Data
1.
Connect Tech-2 to the vehicle. When activated by
turning on the power of Tech-2, push the "Enter"
switch.
2.
Turn on the ignition switch (without starting the
engine)
3.
In the main menu of Diagnostic Tester, push "F1:
Service Programming System (SPS)".
4.
Push "F0: Request Info" of Tech-2.

5.
Where vehicle data has been already saved in
Tech-2, the existing data come on display. In this
instance, as Tech-2 starts asking whether to keep
the data or to continue obtaining anew data from
the control unit, choose either of them.





6.
If you select “continue ”, you have to select “Model
Year ”, “Vehicle Type ”, “Controller Type (Engine) ”.
7.
After that. then push button and turn Ignition
switch tuned on, off, on following Tech-2 display.
Tech-2 will read information from controller afte
r
this procedure.
8.
During obtaining information, Tech-2 is receiving
information from the control unit chosen. In
replacing the control unit, please be sure to
undertake "Obtaining Information" from the new
unit. With VIN not being programmed into the new
control unit at the time of shipment, "obtaining
information" is not complete (because the vehicle
model, engine model and model year are specified
from VIN). For the procedure get additional
information on vehicles, instruction will be
provided in dialog form, when TIS2000 is in
operation.
9.
Following instructions by Tech-2, push the "Exit"
switch of Tech-2, turn off the ignition of the vehicle
and turn off the power of Tech-2, thereby
removing from the vehicle.

3.Data Exchange
1.
Connect Tech-2 to P/C, turn on the power and
click the "Next" button of P/C.
2.
Check VIN of the vehicle and choose "Next".
3.
When a lack of data is asked from among the
following menu, enter accordingly.
Select following Menu

Model Year

Model

Engine type

Transmission type

Destination code (vehicles for general
export)*1

Immobiliser
* 1: How to read the destination code
"Destination code can be read from ID Plate affixed on
vehicles, while on VIN plate the destination code is
described at the right-hand edge of Body Type line. In
Fig.-3, the destination code can be read as "EK4"
(Europe).

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-29





4.
After choosing the data, click the "Next" button.
5.
When all the necessary information is entered, the
"details" of software within the database that
match the entered data will appear fo
r
confirmation. Click the "Program" switch and then
download the new software onto Tech-2.
6. "Data Transfer" comes on display. The progress o
f
downloading will be displayed on the screen in the
form of bar graph.
7.
Upon finishing the data transfer, turn off the powe
r
of Tech-2, removing from P/C.


4. Programming of ECM 1.
Check to see if batteries are fully charged, while
ABS connectors shall be removed from the
vehicle.
2.
Connect Tech-2 to Vehicle Diagnostic Connectors.
3.
Turn on the power of Tech-2 and the title screen
comes on display.
4.
Turn on the ignition (without allowing the engine to
start)
5.
On the title screen of Tech-2, push the "Enter"
button.
6.
Choose "F: Service Programming System" on the
main screen and then choose "Fl: Programming".
7.
While data is being transferred, "Downloading"
will be displayed on the Tech-2 screen.
8.
Upon finishing the data transfer, Tech-2 will
display "Reprogramming Successful". Push the
"Exit" button to bring program to completion.

9.
Following "Procedure 2: Demand of Data", try ove
r
again "Information Obtaining" and check to
confirm if the data has been correctly re-loaded.
10. Upon finishing confirmation, turn off the ignition o
f
the vehicle and then turn off the power of Tech-2,
removing from the vehicle.

7A2-30 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

OBD Diagnostic Management System
Transmission Control Module (TCM) Location

P1010052



RTW37ASH000301