Joint JAGUAR X308 1998 2.G Workshop Manual

In
stallation

12
. R
emove gasket from the manifold flange.
Clean and inspect th
e manif
old joint faces.
Clean and inspect th
e threads on th
e downpipe studs.

1. Fit
the oxygen sensor(s).
The downstream sensor i
s
fitt
ed only for North American
markets.
2. Fit a new gasket to the mani fold mating flange on the
downpipe.

3. Fit
the downpipe catalytic converter.
1. Fit the downpipe assembly to the manifold.
Fit,
but do not fully tighten, the mounting bracket securing

bolts. (Leave loose until the nu ts securing the downpipe to
the exhaust manifold are fitted.)
4. Lower the ramp.
5. Tighten the nuts securing the downpipe flange to the manifold
flange.

In
stallation

8.
Re
move gasket from the manifold flange.
Clean and inspect th
e manif
old joint faces.
Clean and inspect th
e threads on th
e downpipe studs.

1. Fit
the oxygen sensor(s).
The downstream sensor i
s
fitt
ed only for North American
markets.
2. Fit a new gasket to the mani fold mating flange on the
downpipe.

3. Fit
the downpipe catalytic converter.
Fit the down
pipe assemb l
y to the manifold.
Fi
t,
but do not fully tighten, the mounting bracket securing

bolts. (Leave loose until the nu ts securing the downpipe to
the exhaust manifold are fitted.)
4. Lower the ramp.
5. Tighten the nuts securing the downpipe flange to the manifold
flange.

I
nstallation


7.
R
emove the gasket from the front
muffler flange at each side.
R
eposition the front silencer rearwards.
R

emove the gasket from each flange.

8. R
emove the downpipe catalytic converter.
R

emove the bolts which se
cure the downpipe lower
mounting bracket.
Remove the
downpipe assembly.

9. R
emove the oxygen sensor(s).
The downstream sensor i

s fitt
ed only for North American
markets.
10. Remove gasket from the manifold flange.
Clean and inspect th
e manifold joint faces.
Clean and inspect th

e threads
on the downpipe studs.

I
nstallation

7.
R
aise the vehicle on a ramp.

8. R
emove the downpipe catalytic converter.
R

emove the bolts which se
cure the downpipe lower
mounting bracket.
Remove the
downpipe assembly.
9. Remove gasket from the manifold flange.
Clean and inspect th
e manifold joint faces.
Clean and inspect th

e threads
on the downpipe studs.
1. Fit a new gasket to the mani fold mating flange on the
downpipe.

2. F
it the downpipe catalytic converter.
Fit the down

pipe assemb
ly to the manifold
Fi
t, but do not fully tighten, the mounting bracket securing

bolts. (Leave loose until the nu ts securing the downpipe to
the exhaust manifold are fitted.)
3. Lower the ramp.
4. Tighten the nuts securing the downpipe flange to the manifold
flange.

6. R
aise the vehicle on a ramp.

7. R
emove the bolts which secure
the rear of the front muffler
assembly to the engine rear mounting.

8. R
emove the nuts which secure
the front flanges of the front
muffler to the downpipe flanges.

9. R
emove the gasket from the front
muffler flange at each side.
R
eposition the front silencer rearwards.
R

emove the gasket from each flange.

10
.
Remove the downpipe catalytic converter.
R
emove the bolts which se
cure the downpipe lower
mounting bracket.
Remove the
downpipe assembly.
11. Remove gasket from the manifold flange.
Clean and inspect th
e manifold joint faces.
Clean and inspect th

e threads
on the downpipe studs.

Exha
ust System - Catalyti
c Converter Gasket RH4. 0L NA V8 - AJ27/3.2L
NA V8 - AJ26
Re mo
val and Installation
Remova

l
Installation
1. Op
en the engine compartment and fit paintwork protection
sheets.
2. Remove the front muffler; refer to Operation 30.10.18 in this
section.

3. CAUT
ION: Note the position of the upstream and
downstream (where fitted) o xygen sensor multiplugs for
reassembly.
Disconnect the oxygen sensor multiplugs.
Di spl
ace the multiplugs from the engine mounting bracket.

Dis
connect the plug(s) from the oxygen sensor(s).

4.
Re
move the four nuts which se
cure the downpipe catalytic
converter to the exhaust manifold.
5. Raise the vehicle on a ramp.

6. Re
move the downpipe catalytic converter.
R
e
move the bolts which se
cure the downpipe lower
mounting bracket.
Remove the down
pipe assembly.
7. Remove gasket from the manifold flange.
Clean and inspect th e manif
old joint faces.
Clean and inspect th
e threads on th
e downpipe studs.
1. Fit a new gasket to the mani fold mating flange on the

I
nstallation


7.
R
emove the gasket from the front
muffler flange at each side.
R
eposition the front silencer rearwards.
R

emove the gasket from each flange.

8. R
emove the downpipe catalytic converter.
R

emove the bolts which se
cure the downpipe lower
mounting bracket.
Remove the
downpipe assembly.
9. Remove gasket from the manifold flange.
Clean and inspect th
e manifold joint faces.
Clean and inspect th

e threads
on the downpipe studs.
1. Fit a new gasket to the mani fold mating flange on the
downpipe.
2. Fit the downpipe catalytic converter.
1. Fit the downpipe assembly to the manifold.
Fi
t, but do not fully tighten, the mounting bracket securing

bolts. (Leave loose until the nu ts securing the downpipe to
the exhaust manifold are fitted.)

Ex
haust System - Front Muffler4.0L
NA V8 - AJ27/3.2L NA V8 - AJ26
Remo
val and Installation
Remov
a
l
Installation
1. Ra
ise the vehicle on a ramp.

2. Move the front muf f
ler forwar
d to allow the intermediate
mufflers to be displaced.
Slac ken t
he clamps (left-hand and right-hand sides),
catalytic converter to front muffler.

3. Slacken the clamps (left-ha nd and right-hand sides),
i
ntermediate mufflers to front muffler.
4. Remove the front muffler.
Di
sconnect the front muffler
from the intermediate
mufflers and then from the downpipe catalytic converters.

5. Clean and inspect al l ex
haust joints.
1. Fit the front muffler.
Fi
t the front muffler fully into the downpipe catalytic
converters and then slide it rearward to engage the
intermediate mufflers.

2. Correctl
y position the front muffl
er in the catalytic converters
to align the correct reference / index indicator ring..
Tigh ten th
e clamps (left-hand
and right-hand sides), front
muffler to catalytic converters.
3. Correctly position the intermedia te mufflers to the front muffler
to align the correct refere nce / index indicator ring.

Ex
haust System - Front Muffler4.0L SC V8 - AJ26
Re
mo
val and Installation
Remov
a
l
Installation
1. Ra
ise the vehicle on a ramp.

2. Separate the front muf f
ler flan
ge joints from the downpipe
catalytic converters.
Slac ken t
he flange nuts (left-hand and right-hand sides),
catalytic converter to front muffler.

3. Slacken the clamps (left-ha nd and right-hand sides),
i
ntermediate mufflers to front muffler.
Move both i
n
termediate mufflers rearwards, as far as
possible.
4. Remove the flange nuts (lef t-hand and right-hand sides),
catalytic converter to front muffler.

5. Re
move the bolts which secure th
e front muffler rear mounting
to the rear of the gearbox.
6. Remove the front muffler.
Di
sconnect the front muffler fr
om each downpipe flange.
Di
sconnect the front muffler
from the intermediate
mufflers and remove it.
7. Remove the gasket from each front flange joint.
8. Clean and inspect al l exhaust joints.
1. Fit the front muffler.

I
nstallation

7.
Clean and inspect al l e
xhaust joints.

1. Fi
t the intermediate muffler assembly.
F

it the muffler assembly to the axle carrier and to the
over-axle mounting rubber.

2. Locate the intermedi
ate muffl
er to the front muffler.

3. Cor
rectly position the front muffl
er in the catalytic converters
to align the correct reference / index indicator ring..
Tigh
ten the clamps (left-hand
and right-hand sides), front
muffler to catalytic converters.
4. Correctly position the intermedia te muffler at the front muffler
to align the correct reference / index indicator ring..
Tigh
ten the clamp, intermediate
mufflers to front muffler.