rear suspension JAGUAR X308 1998 2.G Owner's Manual

and axle assembly during installa
tion. Failure to follow this
instruction may result in personal injury.
CAUTION: Position a suitable piece of wood between the
jack and the rear suspension and axle assembly. Failure to follow
this instruction may result in damage to the vehicle.
Position the rear suspension and axle assembly on to a trolley
jack.
3. WARN
ING: With assistance, support the rear suspension
and axle assembly during instal lation. Failure to follow this
instruction may result in personal injury.
Position the rear suspension and axle assembly under the
vehicle.

4. WARN
ING: With assistance, support the rear suspension
and axle assembly during instal lation. Failure to follow this
instruction may result in personal injury.
Raise the trolley jack to position the rear suspension and axle
assembly to the vehicle.

5. NOTE : R
ight-hand shown, left-hand similar
Install the mounting brackets.
Po si
tion the mounting brackets to the subframe.
Install but do not tigh
ten
new bolts to the mounting
bracket .

6. NOTE: R
ight-hand shown, left-hand similar
Install new outer bolts to the mounting bracket.
Tigh te
n to 41-54 Nm.
7. NOTE: Right-hand shown, left-hand similar

18
.
Install the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.

19
.
Connect the wheel speed sensor electrical connector.

20
.
Using a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.
21. Install the rear wheels.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.
22
.
Remove the axle stands and lower the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
23
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension


Sy

stem
- General
Information
.

Rear Su
spension - Rear Shock Absorber
Re
mo
val and Installation
Remov
a
l
S
p
ecial Tool(s)

Spri
ng C
ompressors
204-179 (JD 199)

Spri ng Re
taining straps
204-179-1 (JD 199-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-00
General
Informati
o
n
.
R a
ise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-02
Jacking and
Liftin
g.
2. Re
move the relevant rear wheel.
For additional informat ion, refer to Section 204
-04 W
heels and
Tire
s.

3. CAUTIO
N: Do not suspend the caliper from the brake
hose as this will damage the hose.
Remove the brake caliper from the carrier.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.
4. Disc
onnect the wheel speed sensor electrical connector.

22. R
elease the tie strap securing the brake caliper to the
suspension mounting bracket.

23 . Install
the brake caliper on to the carrier.
1. Position the caliper asse mbly on to the carrier.
2. Install the guide pins and tighten to 25-30 Nm.
3. Install the dust caps.
4. Install the brake caliper spring clip.

24 . Conne
ct the wheel speed sensor electrical connector.

25 . U
sing a new tie strap, secure the wheel speed sensor harness
to the brake hose clip.
26. Install the rear wheel.
For additional informat ion, refer to Section 204
-04 W
heels and
Tire
s.
27 .
Remove the
axle stands
and lower the vehicle.
For additional informat ion, refer to Section 100
-02
Jacking and
Liftin
g.

28
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension
Sy

stem
- General
Information
.

Rear Su
spension - Shock Absorber Lower Bushing
Re
mo
val and Installation
Remov
a
l
S
p
ecial Tool(s)

B
u
shing Remover / installer
204-335

Bushing remover
2 04-
533

B
u
shing installer
204-534
1. Mark the orientation of the shock absorber eye in relation to
the lower suspension arm.
2. Remove the rear shock absorber.
For additional information, refer to: Rear Shock Absorber
(20 4
-
02 Rear Suspension, Removal and Installation).

3. NOTE : W
ith assistance make sure the tool is aligned.
Using the special tool, support the shock absorber.
4. NOTE: With assistance make sure the tool is aligned.
Position and align the special tool to the shock absorber bush.

reach
es the stop.
4. Install the rear shock absorber.
For additional information, refer to: Rear Shock Absorber
(204
-
02 Rear Suspension, Removal and Installation).

Rear
Suspension - Spring
Re
moval and Installation
Remov

al
S
pecial Tool(s)

Spri

ng Compressors
204-179 (JD 199)

Spri
ng Retaining straps
204-179-1 (JD 199-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used.
For additional informat ion, refer to Section 100
-0
0 General
Informati

on
.
R
aise the rear of the vehicle
and support on axle stands.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
2.
R
emove the relevant rear wheel.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.

3. CAUTI
ON: Do not suspend the caliper from the brake
hose as this will damage the hose.
Remove the brake caliper from the carrier.
1. Remove the caliper spring clip.
2. Remove the guide pin dust caps.
3. Slacken and withdr aw the guide pins.
4. Remove the caliper from the carrier and secure to the suspension mounting bracket using a tie strap.
4. Di
sconnect the wheel speed sensor electrical connector.

28
.
Install the rear wheel.
For additional informat ion, refer to Section 204
-04
Wheels and
Tire

s
.
29
.
Remove the axle stands and lower the vehicle.
For additional informat ion, refer to Section 100
-0
2 Jacking and
Liftin

g
.
30
.
Check and adjust the rear whee l alignment as necessary.
For additional informat ion, refer to Section 204
-00
Suspension
Sy

stem
- General
Information
.

In
stallation

1.
Posi ti
on monostrut on rear suspension.

2. Align m o
nostrut upper mountings and install but do not tighten
bolts

3. Ra
ise rear of suspension to
align with monostrut lower
mounting holes.

4. Inst al
l monostrut lower bolts and nuts and tighten to 77-103
Nm.
5. Tighten monostrut upper bolts to 88-118 Nm.