Pump JAGUAR XFR 2010 1.G Repair Manual

6.
Remove the oil vacuum pump.

7.

Engine - V8 S/C 5.0L Petrol - Fuel Pump Camshaft Timing Check
General Procedures

Special Tool(s)

303-1447
Timing Tool
JLR-303-1621
Alignment Tool, Fuel Pump Camshaft Timing
Check Published: 16-Dec-2013

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.

Raise and support the vehicle.

3. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

4. CAUTION: Be prepared to collect escaping oil.
NOTES:

Discard the sealing washer.


Collect the engine oil in a clean container.








5.

10. Remove the Special Tool(s): 303-1447


















11.


















If required,
carefully
adjust the
crankshaft
position to
allow correct
installation
of the
special tool.

Install the
Special
Tool(s):
JLR-303-1621
















12.
CAUTION: Do not use excessive force when adjusting the crankshaft
position.


NOTE: If the crankshaft timing tool cannot be installed, adjustment of
the fuel pump camshaft timing will be required.

If required, carefully adjust the crankshaft position to allow correct
installation of the special tool.

Install the Special Tool(s): 303-1447 If the crankshaft timing tool cannot be installed, adjustment of the
fuel pump camshaft timing will be required.

Refer to: Fuel Pump Camshaft Timing Adjustment (303-01C Engine - V8 5.0L Petrol, General Procedures).

Published: 21-Dec-2011
Engine - V8 S/C 5.0L Petrol - Fuel Pump Camshaft Timing Adjustment
General Procedures

Special Tool(s)


303-1447
Timing Tool

JLR-303-1613
Alignment Tool, Fuel Pump Camshaft Timing
Adjustment

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Fuel Pump Camshaft Timing Check (303-01D Engine - V8 S/C 5.0L Petrol, General Procedures).

4. Refer to: Lower Timing Cover (303-01C Engine - V8 5.0L Petrol, Removal and Installation).
Refer to: Lower Timing Cover (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

Engine - V8 S/C 5.0L Petrol - Exhaust Manifold LH
Removal and Installation

Special Tool(s)


303-1444-01
Exhaust Manifold Installation Guide Pins - Threaded

303-1444-02
Exhaust Manifold Installation Guide Pins - Unthreaded Removal

NOTES:


Removal steps in this procedure may contain installation details.


Some variation in the illustrations may occur, but the essential information is always correct. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Power Steering Pump - V8 5.0L Petrol/V8 S/C 5.0L Petrol (211-02 Power Steering, Removal and Installation).

4. Refer to: Catalytic Converter LH (309-00C Exhaust System - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).

Petrol/V8 S/C 5.0L Petrol, Removal and Installation).

16. Refer to: Power Steering Pump - V8 5.0L Petrol/V8 S/C 5.0L Petrol (211-02 Power Steering, Removal and Installation).

17. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
www.JagDocs.com

13.
14.
15.






































NOTE: The high-pressure fuel pumps are removed from the illustration
for clarity.










16. CAUTIONS:


Be
prepared to
collect
escaping
fluids.


Make
sure that all
openings are
sealed. Use
new blanking
caps. www.JagDocs.com

15.
16.
17.
18. Torque: 11 Nm

























Torque: 11 Nm

















NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with clean
engine oil.
















CAUTION: Tighten the Torx screws a turn at a time until the correct
torque is achieved.


NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal with
clean engine oil.

Torque: 11 Nm

19.
20.
21.
22. Loosen the Torx screws half a turn each.





































NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with clean
engine oil.
















CAUTION: Tighten the Torx screws a turn at a time until the correct
torque is achieved.


NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal with
clean engine oil.

Torque: 11 Nm

26.
















27.
28. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.


NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.

Torque: 11 Nm










CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.


NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.

Torque: 11 Nm








NOTES:


Do not tighten at this stage.


Remove and discard the blanking caps.