Control module JAGUAR XFR 2010 1.G Repair Manual

Published: 18-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index V8 S/C 5.0L
Petrol, DTC: Engine Control Module (ECM)
Description and Operation

Engine Control Module (PCM) 5.0L SC V8 - AJ133


WARNING: Fuel injector voltage will reach 65 Volts during operation and have a high current requirement.


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the scan
tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give additional information
read by the manufacturer-approved diagnostic system).


When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads
into account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the electronic engine control module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Electronic Engine Controls (303-14 Electronic Engine Controls - V8 S/C 5.0L Petrol,
Diagnosis and Testing).

DTC Description Possible Causes Action B10A2-31 Crash Input - No signal

NOTE: - Circuit SRS_SIGNAL -

Loss of communication between
restraints control module and
engine control module
Refer to the electrical circuit
diagrams and check restraints
control module pulse width
modulated SRS signal line circuit,
hard wired connection between
engine control module and restraints
control module for short circuit to
ground, short circuit to power, open
circuit. Repair circuit as required,
clear the DTC and retest B10AC-81
Cruise Control Switch -
Invalid serial data received
The engine control module has
received an invalid command from
the steering wheel switch pack
Clear the DTC and press all the
steering wheel switches, re-check for
DTCs. Refer to the electrical circuit
diagrams and check the speed
control switch circuit for open circuit,
short circuit to power, short circuit to
ground, disconnected
Check and install a new steering
wheel module as required. Refer to
the warranty policy and procedures
manual, or determine if any prior
approval programme is in operation,
prior to the installation of a new

DTC Description Possible Causes Action module/component B10AC-82 Cruise Control Switch - Alive / sequence counter incorrect / not updated
Cruise buttons alive counter is not
incrementing. Which suggests that
the LIN bus is faulty
Steering wheel module is not
connected
Steering wheel module failure
Refer to the electrical circuit
diagrams and check the speed
control switch circuit for open circuit,
short circuit to power, short circuit to
ground, disconnected
Refer to the electrical circuit
diagrams and check the LIN bus
between steering wheel module and
the CAN gateway
Check and install a new steering
wheel module as required. Refer to
the warranty policy and procedures
manual, or determine if any prior
approval programme is in operation,
prior to the installation of a new
module/component B10AC-83
Cruise Control Switch - Value
of signal protection
calculation incorrect
Cruise buttons checksum incorrect,
incorrect cruise switches fitted to
vehicle
Check and install new cruise
switches as required. Refer to the
warranty policy and procedures
manual, or determine if any prior
approval programme is in operation,
prior to the installation of a new
module/component B10AC-96
Cruise Control Switch -
Component internal failure
Speed control switch circuit, open
circuit, short circuit to power, short
circuit to ground, disconnected
Speed control switch failure
Steering wheel module failure
Check for related DTCs in other
central junction boxes
Refer to the electrical circuit
diagrams and check the speed
control switch circuit for open circuit,
short circuit to power, short circuit to
ground, disconnected
Check and install a new speed
control switch as required. Check and
install a new steering wheel module
as required. Refer to the warranty
policy and procedures manual, or
determine if any prior approval
programme is in operation, prior to
the installation of a new
module/component B10FF-68
Ignition Control - Event
information
Spark plug(s) fault
Wiring harness fault
Ignition coil(s) fault
Refer to repair manual and check
spark plug(s) for condition and
security. Replace any defective
components as required
Refer to electrical wiring diagrams
and check ignition coil circuit for
intermittent open circuit, short
circuit to power, short circuit to
ground
Check and install a new coil(s) as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component B11DB-01
Battery Monitoring Module -
General electrical failure
NOTE: - Circuit BATTERY -

Charging system fault Battery
monitoring signal line
circuit fault
Vehicle battery fault
Refer to electrical wiring diagrams
and check charging system for faults.
Perform any repairs required
Refer to the electrical wiring
diagrams and check the battery
monitoring system module circuit for
open circuit, short circuit to ground,
short circuit to power
Refer to the workshop manual and
the battery care manual, inspect the
vehicle battery and ensure it is fully
charged and serviceable before
performing further tests

DTC Description Possible Causes Action B11DB-87
Battery Monitoring Module -
Missing message
NOTE: - Circuit BATTERY -

Battery signal line circuit fault
Refer to the electrical wiring
diagrams and check the battery
monitoring system module circuit for
open circuit, short circuit to ground,
short circuit to power
Refer to the electrical circuit
diagrams and check the LIN circuit
for short circuit to ground, short
circuit to power, open circuit B1206-68
Crash Occurred - Event
information
NOTE: - Circuit SRS_SIGNAL -

Engine control module has
detected the vehicle has crashed -
event information DTC only
Refer to the electrical circuit
diagrams and check the engine
control module to restraints control
module circuit for short circuit to
ground, short circuit to power, open
circuit. Repair circuit as required,
clear the DTC and retest C0031-00
Left Front Wheel Speed
Sensor - No sub type
information
Invalid data received from anti-lock
braking system module - left front
wheel speed signal fault
Check anti-lock braking system
module for related DTCs and refer to
relevant DTC index C0034-00
Right Front Wheel Speed
Sensor - No sub type
information
Invalid data received from anti-lock
braking system module - right front
wheel speed signal fault
Check anti-lock braking system
module for related DTCs and refer to
relevant DTC index C0037-00
Left Rear Wheel Speed
Sensor - No sub type
information
Invalid data received from anti-lock
braking system module - left rear
wheel speed signal fault
Check anti-lock braking system
module for related DTCs and refer to
relevant DTC index C003A-00
Right Rear Wheel Speed
Sensor - No sub type
information
Invalid data received from anti-lock
braking system module - right rear
wheel speed signal fault
Check anti-lock braking system
module for related DTCs and refer to
relevant DTC index P0010-13
Intake (A) Camshaft Position
Actuator (Bank 1) - Circuit
open
NOTE: - Circuit VFS_IN_A -

Intake (A) camshaft position
actuator (Bank 1) open circuit
Engine control module interface
harness open circuit
Refer to the electrical circuit
diagrams and check intake (A)
camshaft position actuator (Bank 1)
circuit for open circuit
Refer to the electrical circuit
diagrams and check engine control
module interface harness for open
circuit P0011-00
Intake (A) Camshaft Position
Timing - Over-Advanced
(Bank 1) - No sub type
information
NOTE: - Circuit VFS_IN_A -

Intake (A) camshaft position
actuator (Bank 1) open circuit
Engine control module interface
harness open circuit
Refer to the electrical circuit
diagrams and check intake (A)
camshaft position actuator (Bank 1)
circuit for open circuit
Refer to the electrical circuit
diagrams and check engine control
module interface harness for open
circuit P0013-13
Exhaust (B) Camshaft
Position Actuator (Bank 1) -
Circuit open
NOTE: - Circuit VFS_EX_A -

Exhaust (B) camshaft position
actuator (Bank 1) open circuit
Engine control module interface
harness open circuit
Refer to the electrical circuit
diagrams and check exhaust (B)
camshaft position actuator (Bank 1)
circuit for open circuit
Refer to the electrical circuit
diagrams and check engine control
module interface harness for open
circuit P0015-00
Exhaust (B) Camshaft
Position Timing -
Over-Retarded (Bank 1) - No
sub type information
NOTE: - Circuit VFS_EX_A -

Exhaust (B) camshaft position
actuator (Bank 1) open circuit,
short circuit to ground, short circuit
to power
Check for related DTC P0365-00.
Refer to the electrical circuit
diagrams and check exhaust (B)
camshaft position actuator (Bank 1)
for open circuit, short circuit to
ground, short circuit to power www.JagDocs.com

DTC Description Possible Causes Action P0016-00
Crankshaft Position -
Camshaft Position
Correlation - Bank 1 Sensor A
- No sub type information
NOTE: - Circuit VFS_EX_A -

The relative positions of the
crankshaft position sensor and cam
timing plate teeth are not correct
Engine timing incorrect
Timing chain installed incorrectly
Variable valve timing forced fully
advanced
Check engine timing. Check camshaft
sensor timing plate is installed
correctly. Check timing chain is
installed correctly P0017-00
Crankshaft Position -
Camshaft Position
Correlation - Bank 1 Sensor B
- No sub type information
NOTE: - Circuit VFS_EX_A -

The relative positions of the
crankshaft position sensor and
camshaft timing plate teeth are
not correct
Engine timing incorrect
Timing chain installed incorrectly
Variable valve timing forced fully
advanced
Check for related DTC P0365-00.
Check engine timing. Check camshaft
sensor timing plate is installed
correctly. Check timing chain is
installed correctly
Refer to the electrical circuit
diagrams and check exhaust (B)
camshaft position actuator (Bank 1)
for open circuit, short circuit to
ground, short circuit to power P0018-00
Crankshaft Position -
Camshaft Position
Correlation - Bank 2 Sensor A
- No sub type information
NOTE: - Circuit VFS_IN_B -

The relative positions of the
crankshaft position sensor and
camshaft timing plate teeth are
not correct
Engine timing incorrect
Timing chain installed incorrectly
Variable valve timing forced fully
advanced
Check engine timing. Check camshaft
sensor timing plate is installed
correctly. Check timing chain is
installed correctly P0019-00
Crankshaft Position -
Camshaft Position
Correlation - Bank 2 Sensor B
- No sub type information
NOTE: - Circuit VFS_EX_B -

The relative positions of the
crankshaft position sensor and
camshaft timing plate teeth are
not correct
Engine timing incorrect
Timing chain installed incorrectly
Variable valve timing forced fully
advanced
Check engine timing. Check camshaft
sensor timing plate is installed
correctly. Check timing chain is
installed correctly P0020-13
Intake (A) Camshaft Position
Actuator (Bank 2) - Circuit
open
NOTE: - Circuit VFS_IN_B -

Intake valve solenoid 2 open circuit
Refer to the electrical circuit
diagrams and check intake valve
solenoid 2 for open circuit P0023-13
Exhaust (B) Camshaft
Position Actuator (Bank 2) -
Circuit open
NOTE: - Circuit VFS_EX_B -

Exhaust (B) Camshaft Position
actuator (Bank 2) circuit, open
circuit
Refer to the electrical circuit
diagrams and check exhaust (B)
camshaft position actuator (Bank 2)
circuit for open circuit P0026-72
Intake Valve Control
Solenoid Circuit
Range/Performance (Bank 1)
- Actuator stuck open
NOTE: - Circuit VFS_IN_A -

Intake valve solenoid 1 angle less
than target
Intake valve solenoid 1 slow or not
operating
Check operation of intake valve
solenoid 1. Check and install a new
intake valve solenoid 1 as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of
a new module/component P0026-77
Intake Valve Control
Solenoid Circuit
Range/Performance (Bank 1)
- Commanded position not
reachable
NOTE: - Circuit VFS_IN_A -

Intake valve solenoid 1 angle
greater than target
Intake valve solenoid 1 not
returning to target in time
Check operation of intake valve
solenoid 1. Check and install a new
intake valve solenoid 1 as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of

DTC Description Possible Causes Action Intake valve solenoid 1 stuck
advanced a new module/component P0027-72
Exhaust Valve Control
Solenoid Circuit
Range/Performance (Bank 1)
- Actuator stuck open
NOTE: - Circuit VFS_EX_A -

Exhaust valve solenoid 1 angle
less than target
Exhaust valve solenoid 1 slow or
not operating
Check operation of exhaust valve
solenoid 1. Check and install a new
exhaust valve solenoid 1 as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0027-77
Exhaust Valve Control
Solenoid Circuit
Range/Performance (Bank 1)
- Commanded position not
reachable
NOTE: - Circuit VFS_EX_A -

Exhaust valve solenoid 1 angle
greater than target
Exhaust valve solenoid 1 not
returning to target in time
Exhaust valve solenoid 1 stuck
advanced
Check operation of exhaust valve
solenoid 1. Check and install a new
exhaust valve solenoid 1 as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0028-72
Intake Valve Control
Solenoid Circuit
Range/Performance (Bank 2)
- Actuator stuck open
NOTE: - Circuit VFS_IN_B -

Intake valve solenoid 2 angle less
than target
Intake valve solenoid 2 slow or not
operating
Check operation of intake valve
solenoid 2. Check and install a new
intake valve solenoid 2 as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of
a new module/component P0028-77
Intake Valve Control
Solenoid Circuit
Range/Performance (Bank 2)
- Commanded position not
reachable
NOTE: - Circuit VFS_IN_B -

Intake valve solenoid 2 angle
greater than target
Intake valve solenoid 2 not
returning to target in time
Intake valve solenoid 2 stuck
advanced
Check operation of intake valve
solenoid 2. Check and install a new
intake valve solenoid 2 as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of
a new module/component P0029-72
Exhaust Valve Control
Solenoid Circuit
Range/Performance (Bank 2)
- Actuator stuck open
NOTE: - Circuit VFS_EX_B -

Exhaust valve solenoid 2 angle
less than target
Exhaust valve solenoid 2 slow or
not operating
Check operation of exhaust valve
solenoid 2. Check and install a new
exhaust valve solenoid 2 as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0029-77
Exhaust Valve Control
Solenoid Circuit
Range/Performance (Bank 2)
- Commanded position not
reachable
NOTE: - Circuit VFS_EX_B -

Exhaust valve solenoid 2 angle
greater than target
Exhaust valve solenoid 2 not
returning to target in time
Exhaust valve solenoid 2 stuck
advanced
Check operation of exhaust valve
solenoid 2. Check and install a new
exhaust valve solenoid 2 as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0031-11
HO2S Heater Control Circuit
Low (Bank 1, Sensor 1) -
Circuit short to ground NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Pre catalyst oxygen sensor-odd
heater control circuit (Bank 1,
Sensor 1) circuit short circuit to
ground
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-odd heater control
circuit (Bank 1, Sensor 1) circuit for
short circuit to ground

DTC Description Possible Causes Action P0031-13
HO2S Heater Control Circuit
Low (Bank 1, Sensor 1) -
Circuit open NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Pre catalyst oxygen sensor-odd
heater control circuit (Bank 1,
Sensor 1) circuit, open circuit
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-odd heater control
circuit (Bank 1, Sensor 1) circuit for
open circuit P0032-12
HO2S Heater Control Circuit
High (Bank 1, Sensor 1) -
Circuit short to battery NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Pre catalyst oxygen sensor-odd
heater control circuit (Bank 1,
Sensor 1) circuit short circuit to
power
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-odd heater control
circuit (Bank 1, Sensor 1) circuit for
short circuit to power P0036-00
HO2S Heater Control Circuit
(Bank 1, Sensor 2) - No sub
type information
NOTE: - Circuit HTR_HEGO_A -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-odd
heater control circuit short circuit
to ground, short circuit to power,
open circuit
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-odd
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 2 (0x03A2)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-odd as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0051-11
HO2S Heater Control Circuit
Low (Bank 2, Sensor 1) -
Circuit short to ground NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -

Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit short circuit to
ground
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for
short circuit to ground P0051-13
HO2S Heater Control Circuit
Low (Bank 2, Sensor 1) -
Circuit open NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for

DTC Description Possible Causes Action
Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit, open circuit open circuit P0052-12
HO2S Heater Control Circuit
High (Bank 2, Sensor 1) -
Circuit short to battery NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -


LR - Circuit UHEGO HEATER B -

Pre catalyst oxygen sensor-even
heater control circuit (Bank 2,
Sensor 1) circuit short circuit to
power
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 1 (0x03A4)
Refer to the electrical circuit
diagrams and check pre catalyst
oxygen sensor-even heater control
circuit (Bank 2, Sensor 1) circuit for
short circuit to power P0054-00
HO2S Heater Resistance
(Bank 1, Sensor 2) - No sub
type information NOTES:


- Circuit HTR_CTRL_A_UPSTREAM -


LR - Circuit UHEGO HEATER A -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-odd
heater control circuit short circuit
to ground, short circuit to power,
open circuit, high resistance
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-odd
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 1 Sensor 1 (0x03A1)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-odd sensor circuit for
short circuit to ground, short circuit
to power, open circuit, high
resistance
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-odd as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0056-00
HO2S Heater Control Circuit
(Bank 2, Sensor 2) - No sub
type information
NOTE: - Circuit HTR_HEGO_B -

Post catalyst oxygen sensor-even
heater control circuit short circuit
to ground, short circuit to power,
open circuit
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-even
failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 2 (0x03A5)
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-even, as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0060-00
HO2S Heater Resistance
(Bank 2, Sensor 2) - No sub
type information NOTES:


- Circuit HTR_CTRL_B_UPSTREAM -
Using the manufacturer approved
diagnostic system check datalogger
signal, Oxygen Sensor (O2S) Heater
Duty Cycle Bank 2 Sensor 2 (0x03A5)

DTC Description Possible Causes Action
LR - Circuit UHEGO HEATER B -

Catalyst oxygen sensor heater
circuit control fuse failure
Post catalyst oxygen sensor-even
heater control circuit short circuit
to ground, short circuit to power,
open circuit, high resistance
Catalyst oxygen sensor heater
circuit control relay circuit short
circuit to ground, short circuit to
power, open circuit
Catalyst oxygen sensor heater
circuit control relay failure
Post catalyst oxygen sensor-even
failure Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor fuse for
open circuit
Refer to the electrical circuit
diagrams and check post catalyst
oxygen sensor-even sensor circuit for
short circuit to ground, short circuit
to power, open circuit, high
resistance
Refer to the electrical circuit
diagrams and check catalyst oxygen
sensor heater circuit control relay
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new catalyst
oxygen sensor heater control relay,
as required. Check and install a new
post catalyst oxygen sensor-even as
required. Refer to the warranty policy
and procedures manual, or determine
if any prior approval programme is in
operation, prior to the installation of
a new module/component P0069-29
MAP - Barometric Pressure
Correlation - Signal invalid
Manifold absolute pressure sensor
failure
Engine control module failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Barometric Pressure Sensor
Voltage (0x035A). Check for related
manifold absolute pressure sensor
DTCs
Refer to the electrical circuit
diagrams and check manifold
absolute pressure sensor circuit for
short circuit to ground, short circuit
to power, open circuit
Check and install new manifold
absolute pressure sensor as
required. Check and install a new
engine control module as required.
Refer to the warranty policy and
procedures manual, or determine if
any prior approval programme is in
operation, prior to the installation of
a new module/component P0071-21
Ambient Air Temperature
Sensor Range/Performance -
Signal amplitude < minimum NOTES:


Jaguar - Circuit
AMBIENT_TEMP_SENSOR -


LR - Circuit TAMB TEMP -

Ambient air temperature sensor
circuit short circuit to ground, short
circuit to power, open circuit
Temperature and manifold absolute
pressure sensor circuit short circuit
to ground, short circuit to power,
open circuit
Ambient air temperature sensor
failure
Temperature and manifold absolute
pressure sensor failure
Using the manufacturer approved
diagnostic system check datalogger
signal, Ambient Air Temperature
Sensor Voltage (0x03BA)
Refer to the electrical circuit
diagrams and check ambient air
temperature sensor circuit for short
circuit to ground, short circuit to
power, open circuit
Refer to the electrical circuit
diagrams and check temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit
Check and install a new ambient air
temperature sensor as required.
Check and install a new temperature
and manifold absolute pressure
sensor as required. Refer to the
warranty policy and procedures
manual, or determine if any prior
approval programme is in operation,
prior to the installation of a new
module/component P0071-22
Ambient Air Temperature
Sensor Range/Performance -
Signal amplitude > maximum NOTES:


- Circuit AMBIENT_TEMP_SENSOR -
Using the manufacturer approved
diagnostic system check datalogger
signal, Ambient Air Temperature
Sensor Voltage (0x03BA)
Refer to the electrical circuit www.JagDocs.com

DTC Description Possible Causes Action P007B-24
Charge Air Cooler
Temperature Sensor Circuit
Range/Performance (Bank 1)
- Signal stuck high
NOTE: Jaguar circuit reference
IC_COOLANT_PMP_CTRL &
BOOST_PRESS_SENSOR_TEMP_SIG. Land
Rover circuit reference O_S_CACWPR &
I_A_BTS

Connector is disconnected,
connector pin is backed out,
connector pin corrosion
Fuse failure
Temperature and manifold absolute
pressure sensor circuit, short
circuit to ground, short circuit to
power, open circuit, high resistance
Temperature and manifold absolute
pressure sensor failure
Air charge coolant pump and
control circuit, short circuit to
ground, short circuit to power, open
circuit, high resistance
Air charge coolant pump relay
failure
Air charge coolant pump failure
Inspect connectors for signs of water
ingress, and pins for damage and/or
corrosion
Refer to electrical circuit diagrams
and check for fuse failure, install
new fuse as required
Refer to electrical circuit diagrams
and check the temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit,
high resistance
Check and install a new temperature
and manifold absolute pressure
sensor as required
Refer to electrical circuit diagrams
and check the air charge coolant
pump and control circuit for short
circuit to ground, short circuit to
power, open circuit, high resistance
Refer to electrical circuit diagrams
and check the air charge coolant
pump for open circuit, high
resistance
Refer to the relevant section of the
workshop manual and check the air
charge coolant pump for correct
operation. Check and install a new
air charge coolant pump as required
Clear DTC and retest P007B-29
Charge Air Cooler
Temperature Sensor Circuit
Range/Performance (Bank 1)
- Signal invalid
NOTE: Jaguar circuit reference
IC_COOLANT_PMP_CTRL &
BOOST_PRESS_SENSOR_TEMP_SIG. Land
Rover circuit reference O_S_CACWPR &
I_A_BTS

Connector is disconnected,
connector pin is backed out,
connector pin corrosion
Fuse failure
Temperature and manifold absolute
pressure sensor circuit, short
circuit to ground, short circuit to
power, open circuit, high resistance
Temperature and manifold absolute
pressure sensor failure
Air charge coolant pump and
control circuit, short circuit to
ground, short circuit to power, open
circuit, high resistance
Air charge coolant pump relay
failure
Air charge coolant pump failure
Inspect connectors for signs of water
ingress, and pins for damage and/or
corrosion
Refer to electrical circuit diagrams
and check for fuse failure, install
new fuse as required
Refer to electrical circuit diagrams
and check the temperature and
manifold absolute pressure sensor
circuit for short circuit to ground,
short circuit to power, open circuit,
high resistance
Check and install a new temperature
and manifold absolute pressure
sensor as required
Refer to electrical circuit diagrams
and check the air charge coolant
pump and control circuit for short
circuit to ground, short circuit to
power, open circuit, high resistance
Refer to electrical circuit diagrams
and check the air charge coolant
pump for open circuit, high
resistance
Refer to the relevant section of the
workshop manual and check the air
charge coolant pump for correct
operation. Check and install a new
air charge coolant pump as required
Clear DTC and retest P007C-00
Charge Air Cooler
Temperature Sensor Circuit
Low (Bank 1) - No sub type
information
NOTE: - Circuit TMAP_TEMP_SENSOR
-

Charge air cooler temperature
sensor (Bank 1) circuit short circuit
to ground, open circuit, high
resistance
Charge air cooler temperature
sensor (Bank 1) failure
Refer to the electrical circuit
diagrams and check charge air cooler
temperature sensor (Bank 1) circuit
for short circuit to ground, open
circuit, high resistance
Check and install a new charge air
cooler temperature sensor (Bank 1)
as required. Refer to the warranty
policy and procedures manual, or
determine if any prior approval
programme is in operation, prior to
the installation of a new
module/component

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Front Seat Climate Control Module (DCSM)
Description and Operation

Front Seat Climate Control Module (DCSM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals


Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the seat climate control module, for additional
diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Seats (501-10 Seating, Diagnosis and Testing).

DTC Description Possible Causes Action B10B9-13
Blower Control - Circuit
open
Connectors disconnected or
connector pin damage
Seat blower left circuit -
Open circuit
Blower motor assembly -
Short circuit to ground
Front seat climate control
module failure
Check for any disconnected connectors or damaged
connector pins
Carry out on demand self test using manufacturer
approved diagnostic system to confirm the fault is
present
Refer to the electrical circuit diagrams and check
the front seat climate control module - Circuit
reference LH_FANS_RTN, Circuit reference
LH_FANS_PWR - For open circuit. Repair circuit as
required, clear DTC and retest
Carry out on demand self test using manufacturer
approved diagnostic system to confirm
rectification. Alternatively, carry out any pinpoint
tests associated with this DTC using the
manufacturer approved diagnostic system B10B9-4B
Blower Control - Over
temperature
Mechanical restriction in
blower motor assembly
Seat blower left circuit -
Short circuit to ground
Blower motor assembly -
Short circuit to ground
Front seat climate control
module failure
Check for mechanical restriction or debris in seat
blower
Carry out on demand self test using manufacturer
approved diagnostic system to confirm the fault is
present
Refer to the electrical circuit diagrams and check
the front seat climate control module - Circuit
reference LH_FANS_RTN, Circuit reference
LH_FANS_PWR - For short circuit to ground. Repair
circuit as required, clear DTC and retest