manual transmission JAGUAR XJ6 1994 2.G Service Manual

Pomrtrain Automatic Transmission (V12 & AJ16 Supercharged)
8.2.22 MANUAL DETENT SPRING, RENEW
SRO 44.26.10
9 Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
. Remove the fluid pan, see Subsection 8.2.14 (4,OL SC) or
. Remove the fluid filter, see Subsection 8.2.18.
. Select 'P (Park) and ensure that the pawl is engaged.
Release and remove the manual valve detent spring and
Remove the detent spring assembly and place aside.
. Clean the relevant parts.
Fit a new detent spring assembly to the valve body.
Fit but do not fully tighten the detent spring assembly to
the valve body securing bolts.
. Align the detent spring tocentralize the roller with the det- ent lever in the 'P' (Park) position.
. Check that in 'N' (Neutral), the shift lever is properly in
position. It is essential that the detent spring within the
transmission unit dictates to the shift lever and not the
other way around.
Finally tighten the detent spring assembly to valve body
securing bo
I ts .
(4,OL SC AND 6,011
tion 8.2.13.
Sub
-section 8.2.15 (6,OL).
roller assembly to valve body securing bolts.
. Refit the fluid filter, see Subsection 8.2.18.
Refit the fluid pan, see Subsection 8.2.14 (4,OL SC) or
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Subsection 8.2.13.
. Remove the fender cover and close the hood.
Sub
-section
8.2.15 (6,OL).
X300 VSM 23 Issue 1 August 1994

Snecif icat ion W -I- ..........
e
0
CON TENTS
Title Page
Specification. 1995 Model Year Vehicles ................................................................... 1
EngineManagementSystem ........................................................................\
. 1
Cooling System ........................................................................\
............ 7
Fuelsystem Pump ........................................................................\
......... 7
Clutch ........................................................................\
................... 7
Manual Transmission Ratios ........................................................................\
. 1
Automatic Transmission Ratios ....................................................................... \
2
Final Drive Unit Ratios ........................................................................\
..... 2
Climate Control System ........................................................................\
..... 2
Braking System ........................................................................\
............ 3
Steering&Suspension ........................................................................\
...... 4
Electrical Equipment ........................................................................\
....... 5
Lubricants & Fluids ........................................................................\
......... 7
Vehicle Weights ........................................................................\
........... 9
Tires ........................................................................\
.................... 10
Snowchains ........................................................................\
............. 17
Bulbs ........................................................................\
................... 12
Fuses ........................................................................\
................... 14
Issue 1 August 1994 AI-95MY i X300 VSM

SPECIFICATION - 1995 MODEL YEAR VEHICLES
Engine See relevant engine service manual
Engine Management System
VI2 ............................................................... Nippondenso
6cyl. .............................................................. LucasGEMS
Cooling System
Water pump
type
............................................................... Centrifugal
Cooling fans
- 6 cyl. ................................................ Two electric fans controlled by
Cooling fans
- VI2 ................................................. One engine driven fan and two
Cooling system control
............................................. Thermostat (two on V12)
Thermostat opening temperature .................................... 88OC
Fully open at ....................................................... 93,5 to 96OC
Filler cap pressure rating ........................................... 1,2 bar
drive
.............................................................. Belt
temperature sensor in radiator
electric fans controlled by
temperature sensor
in radiator
Fuel System Pump
one fitted on 6 cyl. (3.2 Liter and 4.0 Liter normally aspirated)
two fitted on 6
cyl. (4.0 Liter supercharged) and VI2
Electrical, module type, fitted in the tank. Integral 70 micron filter.
Make
.............................................................. Nippondenso
Fuel pressure (nominal)
............................................ 3,O bar
Second
pump switches at:
Pump
type
......................................................... Regenerative turbine
Fuel pressure (supercharged)
....................................... 3,7 bar max.
4.0 Liter supercharged ........................................... in at 4000 RPM
out at 3200 RPM
VI2 ............................................................ load sensitiveswitching
Clutch
Plate diameter .....................................................
Clutch hydraulic fluid ............................................... DOT 4
280mm single plate, LUK
Manual Transmission Ratios (Gefragl
First gear .......................................................... 3,553:l
Second gear ....................................................... 2,041: 1
Third gear ......................................................... 1,400 : 1
Fourth gear
........................................................ 1,000 : 1
Fifth gear
.......................................................... 0,755:l
Reverse ........................................................... 3,553: 1
Issue 1 August 1994 X300 VSM AI-95MY 1

Specification
W
. fmmJ
Automatic Transmission Ratios (ZF)
First .............................................................. 2. 48. 1
Second ............................................................ 1. 48.1
Third
.............................................................. 1. 00. 1
Fourth ............................................................. 0. 73.1
Reverse
........................................................... 2.09:l
Automatic Transmission Ratios (Powertrain)
First ............................................................. 2. 482. 1
Second ........................................................... 1. 482. 1
Third ............................................................ 1. 000. 1
Fourth ........................................................... 0. 750.1
Reverse
......................................................... 2. 077 : 1
Final Drive Unit Ratios
3.2 liter Manual .................................................... 3. 77:1
3.2 liter Automatic
.................................................. 4. 08:1
4.0 liter Automatic
.................................................. 3. 54:1
4.0 liter Manual
.................................................... 3. 54:1
4.0 liter Supercharged
.............................................. 3. 27:1
6.0 liter ........................................................... 3. 54:1
Climate Control (air condit;oning) System
Compressor ....................................................... Nippondenso 1OPA17C
Compressor lubricant .............................................. ND Oil 8
Refrigerant ........................................................ R134A
Refrigerant Charge Weight .......................................... 1100g
X300 VSM Issue 1 August 1994 A1-95MY 2

0 LUBRICANTSAND FLUIDS
Engine
Oil
Specification ....................................................... A.P.I. SG I CD or
A.P.I. SH (when available)
SAE Viscosity Range
............................................... 5w 120 - 20w J 50
dependent on ambient temperature
6 cyi. (3.2L and 4.0L) ............................................. 8 liters
VI2 ............................................................ 10liters
Capacities
Manual Transmission (3.21 & 4.01)
Fluid Specification ................................................. Dexron IlD, Dexron IIE
Capacity.. ......................................................... 1,4 liters
Rear Axle Fluid
Specification ....................................................... A.P.I. GL5
Fluid Make &Type
................................................. Shell Spirax Super 90 oil
SAE
Viscosity Rating
............................................... EP 90
(alternative brands may be used for
top
-up only when Shell Spirax is not
available)
0
Capacity (all vehicles) .............................................. 2,l liters
Power Assisted Steering
Preferred fluid ..................................................... Dexron IIE
Alternative fluid .................................................... Dexron IID (use only when Dexron IIE is not available)
Capacity
........................................................... 1,0 liter approximately
Cooling System
Coolant Mixture Specification ....................................... 50% plain water, 50% Jaguar Anti - freeze, Coolant and Corrosion
Inhibitor conforming to specification ESBM97B49A (for
frost protection down to -36OC (-33OF))
Capacities:
6
cyl. (3.2L and 4.OL normally aspirated)
initial
fill ....................................................... 12 liters
drain and refill
.................................................. 7,7 liters
6cyl. (4.0L SC)
initial
fill ........................................................ 13,5 liters
drain and refill .................................................. 9,25 liters
initial
fill.. ...................................................... 19,2 liters
drain and refill .................................................. 14,5 liters
VI 2
Issue 1 August 1994 X300 VSM AI-95MY 7

SECTION CON TENTS
Suh-Section Title SRO Page
i Toiii ............ PreliminaryPages ................................................................ i Toiii
A4.1
............. Body Repair, Introduction ............................................................. 1
A4.1.1 ........... Health And Safety .................................................................... 1
A4.1.2 ........... Notification Of Hazards ............................................................... 2
A4.1.3 ........... Potential Risks ....................................................................... \
3
A4.1.3.1
.......... Potential Risks. Paint ................................................................. 3
A4.1.3.2
.......... Potential Risks. Applied Heat (Welding) .................................................. 3
A4.1.3.3 .......... Potential Risks. Metal Repair ........................................................... 3
A4.1.4 ........... Precautions ........................................................................\
. 3
A4.1.4.1 ..........
A4.1.4.2 ..........
A4.1.4.3 ..........
A4.1.5 ...........
A4.1.5.1 ..........
A4.1.6 ...........
A4.1.6.1 ..........
A4.1.6.2 ..........
A4.1.6.3 ..........
A4.1.6.4 ..........
A4.1.6.5 ..........
A4.1.6.6. .........
Precautions. Paint .................................................................... 3
Precautions. Applied Heat
............................................................. 3
Precautions. Metal Repair ............................................................. 3
General Repair Notes ................................................................. 4
Welding & Gas Processes. Special Notes ................................................. 4
Plastic Component & Trim Materials. - Table ............................................. 5
Plastics. Explanatory Notes ............................................................ 5
Plastics. Handling Notes .............................................................. 5
Recycled Materials
................................................................... 5
Plastics. Component Location & Type - External. Illustration ................................. 6
Plastics. Component Location
& Type - Internal. Illustration ................................. 7
Plastics. Component Location & Type - Underhood. Illustration .............................. 8
A4.2 ............. Body Structure. ...................................................................... 9
A4.2.1 ........... Body Structure. Introduction ........................................................... 9
A4.2.2.1 .......... Body Alignment. Datum Location ...................................................... 10
A4.2.2.2 .......... Body Alignment. Plan View - Key to Illustration .......................................... 10
A4.2.2.3 .......... Body Alignment. Side View - Key to Illustration .......................................... 12
A4.2.3 ........... Zinc Coated Panels .................................................................. 14
A4.2.3.1 .......... Zinc Coated Panels. Description ....................................................... 14
A4.2.3.2
.......... Zinc Coated Panels. Welding Preparation ............................................... 14
A4.2.3.3
.......... Zinc Coated Panels. Body Fillers ....................................................... 14
A4.2.3.4
.......... Zinc Coated Panels. Refinishing ....................................................... 14
A4.2.4
........... Panels -Associated. Renew ..................................... 77.10.02 ............ 15
A4.2.5
........... Surfaces (Old). Prepare .......................................... 77.10.03 ............ 16
A4.2.5.1 .......... Surfaces (New). Prepare ......................................... 77.10.04 ............ 16
A4.2.5.2 .......... Panels -Align And Weld ........................................ 77.10.05 & 06 ....... 17
A4.2.6 ........... Cutting And Welding Symbols ......................................................... 18
A4.3.1 ........... Adhesive. Sealers and Body Protection - Approved Systems ................................ 19
A4.3.
1 . 1 .......... Body Sealing & Preservation Manual - Section Relevance ................................. 19 A4.3.2 ........... Cavity Wax Injection ................................................................ 19
A4.3.2.1
.......... Cavity Wax Injection Points - Front. Illustration .......................................... 20
A4.3.2.2. ......... Cavity Wax Injection Points - Rear, Illustration ........................................... 21
A4.3.3 ........... Underseal. Application Area .......................................................... 22
A4.3.4
........... Insulation Pads. Location ............................................................. 23
A4.3.5
........... Foamlnjection ..................................................................... 24
A4.4.1 ........... Paint Systems - Approved. Table ...................................................... 25
A4.4.1.1
.......... General Recommendations (Paint Refinishing Manual) .................................... 25
A4.4.1.2
.......... Paint Refinishing Manual. Section Relevance ............................................ 25
A4.4.2
........... ‘Black-Out’ Areas. Illustration ......................................................... 26
A4.4.3 ........... Anti-theft labels .................................................................... 27
A4.4.3.1
.......... Anti-theft labels. Original Components ................................................ 27
A4.4.3.2
.......... Anti-theft Labels. Replacement Components ............................................ 27
A4.4.3.3 .......... Anti-theft Labels. Procurement ........................................................ 27
A4.4.3.4
.......... Anti-theft Labels. Location -Front ..................................................... 28
A4.4.3.5
.......... Anti-theft Labels. Location - Rear ...................................................... 29
A4.4.3.7.
......... Anti-theft Labels. Fitting Process ....................................................... 31
A4.2.1.1
.......... Body Structure.
Constructional Steel Classification - Table .................................. 9
A4.2.2 ........... BodyAlignment ..................................................................... 9
A4.4.3.6 .......... Anti-theft Labels. Location -Power unit & Transmission ................................... 30