lift JEEP GLADIATOR 2023 User Guide

GETTING TO KNOW YOUR VEHICLE51
vehicle). The mirror should be adjusted while set in
the day position (toward the windshield).

Manual Mirror Adjustment

Automatic Dimming Mirror — If Equipped
The rearview mirror can be adjusted up, down, left,
and right. The mirror should be adjusted to center
on the view through the rear window.
This mirror automatically adjusts for headlight
glare from vehicles behind you.
NOTE:The Automatic Dimming Mirror feature is disabled
when the vehicle is in REVERSE to improve the
driver’s rear view.
Automatic Dimming Mirror
The Automatic Dimming feature can be turned on
or off through the Uconnect Controls button on the
touchscreen.
ILLUMINATED VANITY MIRRORS
To access an illuminated vanity mirror, flip down
one of the visors and lift the cover.

Illuminated Vanity Mirror

OUTSIDE MIRRORS
The Outside Mirrors are located on the front driver
and passenger side doors, and are adjusted
manually or by power adjustment (if equipped).
To receive maximum benefit, adjust the Outside
Mirror(s) to center on the adjacent lane of traffic
with a slight overlap of the view obtained on the
inside mirror.
Outside Rearview Mirror

For information on the Door Off Mirror Kit (if
equipped) when the front doors are removed, see
Ú page 34.
CAUTION!
To avoid damage to the mirror during cleaning,
never spray any cleaning solution directly onto
the mirror. Apply the solution onto a clean cloth
and wipe the mirror clean.2

23_JT_OM_EN_USC_t.book Page 51

GETTING TO KNOW YOUR VEHICLE69
Console Storage Compartment
The center console has both an upper and lower
storage compartment. To open the upper storage
compartment, lift the top latch. To access the lower
storage compartment, lift the bottom latch.

Center Console

Under Seat Storage — If Equipped
Your vehicle may be equipped with two options for
under seat storage:
Non-Locking Storage Wall
Under Seat Locking Storage Bin
Non-Locking Storage Wall

Non-Locking Storage Wall

The Non-Locking Storage Wall can be used for
storage by folding the bottom of the rear seat up
and placing items behind the wall.
There is also an option to remove the wall by
removing the four bolts that connect the storage
wall to the floor. Locking Storage Bin

Locking Storage Bin (Closed View)

If equipped, the Locking Storage Bin is located
below the rear seats. It can be accessed by folding
the rear seat bottom upward into the Stadium
Position.
The Locking Storage Bin has two keyed locks on
the front of the bin and uses the same key as the
glove compartment and the center console for your
vehicle.
Inside the bin are three removable dividers to set
up storage that works best for you.
1 — Upper Console Storage Latch
2 — Lower Console Storage Latch2

23_JT_OM_EN_USC_t.book Page 69

GETTING TO KNOW YOUR VEHICLE73
Jeep® Wireless Speaker Location

Wireless Speaker Location

The Jeep® wireless speaker is located behind the
right rear passenger seat. In order to access the
Jeep® wireless speaker, the seat will need to be
folded down or tilted forward.
To remove the Jeep® wireless speaker, pull on the
strap located on top of the mount for the speaker.
When the strap is pulled, the Jeep® wireless
speaker can easily be lifted from the mount.
When placing the Jeep® wireless speaker back in
the mount, simply put the speaker back in the
mount.
Placement of the Wireless Speaker

Then push/rotate forward on the front of the
speaker until the speaker locks in place.

Rotating the Wireless Speaker

Charging External Devices
The Jeep® wireless speaker is capable of charging
most USB-enabled smartphones and tablets using
the type A USB charging port.
To use the external charging feature:

1. Turn the speaker on.

2. Plug the USB power cable into the type A USB charging port on the back of the speaker.
3. Insert the other end of the USB power cable into your device to immediately begin
charging.
Charging The Speaker
Before using the Jeep® wireless speaker for the
first time, fully charge your Jeep® wireless speaker
until the battery indicator light stays solid green.
The Jeep® wireless speaker in-vehicle dock is the
most ideal way to fully charge the speaker with the
ignition in ON/RUN or ACC. The speaker can also
be charged with a power adapter.
NOTE:Jeep® wireless speaker will not charge within
vehicle dock while the ignition is fully off.
2

23_JT_OM_EN_USC_t.book Page 73

GETTING TO KNOW YOUR VEHICLE83
(Continued)
LOWERING THE SOFT TOP
Use this QR code to access your
digital experience. If the temperature is below 72°F (24°C) and/or
the top has been folded down for a period of time,
the top will appear to have shrunk when you raise
it, making it difficult to put up. This is caused by a
natural contraction of the vinyl or acrylic materials
of the fabric top.
Place the vehicle in a warm area. Pull steadily on
the top fabric. The vinyl will stretch back to its
original size and the top can then be installed. If
the temperature is 41°F (5°C) or below, do not
attempt to put the top down or roll the rear or side
curtains.
WARNING!
Do not drive the vehicle with the rear window
up/removed unless the quarter windows are
also removed. Dangerous exhaust gases
could enter the vehicle causing harm to the
driver and passengers.
The fabric quarter windows and fabric top are
designed only for protection against the
elements. Do not rely on them to contain occu -
pants within the vehicle or to protect against
injury during an accident. Remember, always
wear seat belts.
Make sure hands and fingers are clear of all
pinch points when installing and removing the
soft top. The lift assist mechanism and side
bows may cause serious injury if fingers or
hands get caught in between.
CAUTION!
The soft top is not designed to carry any
additional loads such as roof racks, spare tires,
building, hunting or camping supplies, and/or
luggage, etc. Also, it was not designed as a
structural member of the vehicle and, thus,
cannot properly carry any additional loads other
than environmental (rain, snow, etc.).
CAUTION!

Do not run a fabric top through an automatic
car wash. Window scratches and wax buildup
may result.

Do not lower the top when the temperature is
below 41°F (5°C). Damage to the top may
result.

Do not move your vehicle until the top has been
either fully attached to the windshield frame, or
fully lowered.
Follow the proper steps for cleaning and caring
for your vehicle’s fabric top
Ú
page 413.
Do not use any tools (screwdrivers, etc.) to pry
or force any of the clamps, clips, or retainers
securing the soft top. Do not force or pry the soft
top framework when opening or closing.
Damage to the top may result.

Failure to follow these cautions may cause interior
water damage, stains, or mildew on the top
material:

It is recommended that the top be free of water
prior to opening it. Operating the top, opening a
door or lowering a window while the top is wet
may allow water to drip into the vehicle's interior.

Careless handling and storage of the soft top
may damage the seals, causing water to leak
into the vehicle's interior.
The soft top must be positioned properly to
ensure sealing. Improper installation can cause
water to leak into the vehicle's interior.

CAUTION!
2

23_JT_OM_EN_USC_t.book Page 83

86GETTING TO KNOW YOUR VEHICLE
Lowering The Soft Top Into The Sunrider® Position:
Use this QR code to access your
digital experience.

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling
the handle downward. Make
sure the hook is fully disengaged from its
receiver.

Step Two

3. From both the left and right sides, lift up on the #1 Bow of the soft top to begin the operation.
It is recommended to utilize two people for this
procedure.
Step Three

4. Move to the side of the vehicle and use the side link to fold the soft top rearward.

Step Four
5. Secure the top in this position by using the two
hook-and-loop fasteners provided in the
center console.

Step Five

NOTE:The vehicle can be driven in the Sunrider® Position
with the rear window and quarter panel cover
assemblies fully installed or completely removed.
CAUTION!
Quarter panel cover assemblies and rear
window must be either all in or all out.

23_JT_OM_EN_USC_t.book Page 86

90GETTING TO KNOW YOUR VEHICLE
2. Using the side link, lift and push the soft top toward the front of the vehicle, manually
guiding the top into the closed position.

Step Two
Step Two

3. From inside the vehicle, pull the handle on the header latch downward to engage the hook
into its receiver.
Step Three

4. Pull the handle back upward while squeezing the hook, locking the latch into place.

Step Four

5. Repeat steps three and four on the other side.
Installing The Rear Window And Quarter
Panel Cover Assemblies
NOTE:Both quarter panel cover assemblies and the rear
window must ALL be removed together, or installed
together.
If the rear window and quarter panel cover
assemblies were previously removed, proceed as
follows to install:

1. Guide the top of the quarter panel cover assembly up into the retainer.

Step One

CAUTION!
Failure to follow all quarter panel cover
assembly and rear window install steps could
result in damage to the Soft Top or vehicle.

23_JT_OM_EN_USC_t.book Page 90

92GETTING TO KNOW YOUR VEHICLE
7. Tuck the rear window under the soft top fabric and press firmly.

Step Seven

8. Engage the rear window retainers in the lower right and left corners.
REMOVING THE SOFT TOP
Use this QR code to access your
digital experience.

1. Fully lower the soft top to the Sunrider® position

Ú
page 83.
2. Using the provided #T50 Torx head driver and
ratchet, unscrew the two Torx head fasteners
on the inside of each top mechanism.

Step Two

3. Utilizing two people, lift the soft top up and away from the vehicle, careful to avoid the
vehicle’s sport bar and trim. Store the soft top
in a safe, clean, and dry location.
4. Remove the door frames. The rear door frames must be removed before the front door frames
Úpage 104. 5. Using the provided #T50 Torx head driver and
ratchet, unscrew the six Torx head fasteners
on both rear corners and the back of the cab,
then remove the belt rail.
NOTE:Folding down the rear seats is recommended to
provide easier access to the fasteners.

Step Five

CAUTION!
Quarter panel cover assemblies and rear
window must be either all in or all out.
CAUTION!
Failure to follow the next steps could result in
damage to the soft top or vehicle.
1 — Corner Fasteners
2 — Rear Fasteners

23_JT_OM_EN_USC_t.book Page 92

GETTING TO KNOW YOUR VEHICLE93
INSTALLING THE SOFT TOP
NOTE:If installing the soft top immediately after removing
the hard top, ensure the wire harness is stored
properly, and not tucked under the belt rail
Úpage 98.

1. Install the belt rail on the rear of the vehicle. Secure the belt rail using the six fasteners
with the provided #T50 Torx head driver and
ratchet. Refer to the following table for
recommended torque specifications.
Step One

2. Install the door frames. Start with both front doors, followed by both rear doors. Apply the
appropriate torque specifications for the door
frame Torx head fasteners Ú page 104.3. Unsnap and remove the storage bag. This bag
should be discarded. It was intended as a
protective cover for shipping only.
4. Ensure the top is secured with the provided hook-and-loop fasteners, then lift the soft top
onto the rear of the cab. Line up the locater
pins (one on each side of the soft top) with the
rear door frames.

Step Four

Torque
Specification For Torx
Fastener Maximum Minimum
119.5 in-lb (13.5 N·m) 150.5 in-lb
(17.0 N·m) 106.2 in-lb
(12.0 N·m)
CAUTION!
Do not overtighten Torx fasteners. Damage to
the retainers will occur.
1 — Corner Fasteners
2 — Rear Fasteners
CAUTION!
Failure to follow the next steps could result in
damage to the soft top or vehicle.
2

23_JT_OM_EN_USC_t.book Page 93

102GETTING TO KNOW YOUR VEHICLE
5. Repeat steps 3 and 4 on the other side of the vehicle.
NOTE:The recommended torque specification for the
front and rear door rail attachment bolts is 8.8 ft-lb
(12 N·m).
6. Attach the rear clamp at the rear center of the Sunrider® top using the two provided rear
clamp attachment bolts. Tighten with #40 Torx
head driver until snug.

Rear Clamp Location

NOTE:The recommended torque specification for the rear
clamp attachment bolts is 3.7 ft-lb (5 N·m). 7. From inside the vehicle, lift and pull the
Sunrider® top forward using the integrated
handle on the front header of the top.
Manually guide the top into the closed
position.

Push Sunrider® Top Forward
8. From inside the vehicle, pull the handle on the
header latch downward to engage the hook
into its receiver. Pull the handle back upward
while squeezing the hook, locking the latch
into place. Repeat on the other side.

Engage Both Header Latches

23_JT_OM_EN_USC_t.book Page 102

GETTING TO KNOW YOUR VEHICLE103
To Open The Sunrider® Top
To open the Sunrider® top, proceed as follows:

1. Fold both sun visors forward against the windshield.

2. Release the header latches from the crossbar by pulling the handle downward. Make sure
the hook is disengaged from its receiver.

Release Both Header Latches
3. From the front of the Sunrider® top, lift and
push the top rearward to the Sunrider®
position.

Sunrider® Position
4. Secure the top by using the two hook-and-loop
fasteners provided with the Sunrider® kit, and
wrap one around the side rails on each side of
the Sunrider® top to hold it in place.

Hook-And-Loop Fastener Placement

2

23_JT_OM_EN_USC_t.book Page 103