relay KIA CARNIVAL 2007 User Guide

67Variable Intake Solenoid Valve #2 control output
Manifold Side]
68 Throttle Position Sensor signal (PWM) output ABS/ESP Control Module
69 Cruise "MAIN" lamp control output Cruise "MAIN" Lamp
70 Fuel Pump Relay control output Fuel Pump Relay
71 Variable Intake Solenoid Valve #1 control output Variable Intake Solenoid (VIS) Valve #1 Surge
Tank Side]
72 Immobilizer lamp control output Immobilizer Lamp
73 -y
74 -y
75 -y
76 -y
77 -y
78 Purge Control Solenoid Valve control output Purge Control Solenoid Valve (PCSV)
79 Wheel Speed Sensor [Low] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
80 Wheel Speed Sensor [High] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
CONNECTOR [C151- 2] Pin
No. Description
Connected to
1 ETC Motor [- ] control output ETC Motor (in ETC Module)
2 ETC Motor [+] control output ETC Motor (in ETC Module)
3 -y
4 CVVT Oil Temperature Sensor signal input CVVT Oil Temperature Sensor (OTS)
5 -y
6 -y
7 Engine Coolant Temperature Sensor signal input Engine Coolant Temperature Sensor (ECTS)
8 Manifold Absolute Pressure Sensor signal input Manifold Absolute Pressure Sensor (MAPS)
9 -y
10 -y
11 Reference voltage (+5V) Manifold Absolute Pressure Sensor (MAPS)
12 Battery voltage supply after ignition switch Ignition Switch
13 Reference voltage (+5V) Throttle Position Sensor (TPS) #2
14 Sensor ground Throttle Position Sensor (TPS) #1
15 Reference voltage (+5V) Camshaft Position Sensor (CMPS) [Bank 2]
16 Reference voltage (+5V) Throttle Position Sensor (TPS) #1
17 Sensor ground Camshaft Position Sensor (CMPS) [Bank 2]
18 Sensor ground Camshaft Position Sensor (CMPS) [Bank 1]
19 Ignition Coil (Cylinder #6) control output Ignition Coil (Cylinder #6)
20 -y
21 Crankshaft Position Sensor [High] signal input Crankshaft Position Sensor (CKPS)
22 -y
Knock Sensor (KS) [Bank 1], Knock Sensor (KS)

15Alternator load signal input IdlePulseHi: Battery Voltage
13.67V
Lo: Max 1.5 V - 0.125mV
16 Cruise Switch ground IdleDCMax. 50 mV 22.44mV
17 - yy y y
18 A/C switch "ON" signal input A/C Relay OFF
DCBattery Voltage
12.37V
A/C Relay ON Max. 1.0V- 25mV
19 - yy y y
20 - yy y y
21 Brake switch signal input Pedal Release
DCBattery Voltage
13.97V
Pedal Push Max. 0.5V- 25mV
22 - yy y y
23 Brake lamp signal input Pedal Release
DCMax. 0.5V
- 225mV
Pedal Push Battery Voltage12.97V
24 - yy y
25 Cruise Switch signal input All Release
DC4.3 ~ 4.7V
4.39V
Main SW Battery Voltage13.37V
Set SW 1.3 ~ 1.7V1.38V
Resume SW 2.8 ~ 3.2V2.82V
Cancel SW - 0.2 ~ 0.2V- 37.54mV
26 A/C thermal switch signal input A/C OFF
DCMax. 1.0V
- 25mV
A/C ON Battery Voltage12.57V
27 Diagnostic Data Line (K- Line) When
transmitting
PulseHi: Min. Vbatt
× 80% 11.57V
Lo: Max. Vbatt ×
20% 175mV
When receiving Hi: Min. Vbatt
× 70% y
Lo: Max. Vbatt ×
30% y
28 - yy y y
29 - yy y y
30 - yy y y
31 - yy y y
32 A/C Pressure Transducer signal
input A/C OFF
DC0 ~ 5V 1.36V
A/C ON 1.83V
33 Sensor ground IdleDCMax. 50 mV 22.66mV
34 - yy y y
35 - yy y y
36 - yy y y
37 - yy y y
38 Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.77V
39 Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.77V
IG OFF Max. 1.0 V- 25mV

40Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.37V
41 CAN [High] Recessive
Pulse2.0 ~ 3.0 V
2.4V
Dominant 2.75~4.5 V3.56V
42 CAN [Low] Recessive
Pulse2.0 ~ 3.0 V
2.42V
Dominant 0.5~2.25 V1.62V
43 Main Relay control output Relay ON
DCBattery Voltage
0.875V
Relay OFF Max. 1.0V12.47V
44 Intake Air Temperature Sensor
signal input Idle
Analog 0 ~ 5V 2.05V
45 Immobilizer communication line When
communicating after IG ON PulseHi: Min. 8.5V
11.87V
Lo: Max. 3.5V 875mV
46 - yy y y
47 Mass Air Flow Sensor signal
input
Idle
Pulse Hi: Vcc
4.97V
Lo: Max. 0.5V 70mV
48 Sensor ground IdleDCMax. 50 mV 22.52mV
49 Accelerator Position Sensor #2
signal input C.T
Analog 0.3 ~ 0.9V
0.38V
W.O.T 1.5 ~ 3.0V2V
50 - yy y y
51 Cruise "SET" lamp control output Cruise OFF
DCBattery Voltage
12.57V
Cruise ON Max. 1.0V- 25mV
52 Vehicle speed signal input Vehicle RunPulseHi: Min. 5.0V
11.07V
Lo: Max. 1.0V - 125mV
53 Sensor ground IdleDCMax. 50 mV 22.37mV
54 Accelerator Position Sensor #1
signal input C.T
Analog 0.3 ~ 0.9V
819mV
W.O.T 4.0 ~ 4.8V4.01V
55 Sensor ground IdleDCMax. 50mV 22.6mV
56 - yy y y
57 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
58 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
59 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
60 - yy y y
61 Engine speed signal output IdlePulseHi: Battery Voltage
13.57V
Lo: Max. 0.5V - 25mV
20 ~ 26Hz y
62 Fuel consumption signal output IdlePulseHi: Battery Voltage
13.57V
Lo: Max. 0.5V - 25mV
63 Malfunction Indicator Lamp (MIL)
control output Lamp OFF
DCHi: Battery Voltage
13.37V
Lamp ON Lo: Max. 2.0V- 25mV

64A/C Compressor Relay control
output A/C OFF
DCBattery Voltage
13.97V
A/C ON Max. 1.0V175mV
65 Cooling Fan [Low] control output Fan OFF
DCBattery Voltage
13.77V
Fan ON Max. 1.0V175mV
66 Cooling Fan [High] control output Fan OFF
DCBattery Voltage
13.57V
Fan ON Max. 1.0V- 25mV
67 Variable Intake Solenoid Valve
#2 control output Active
DCMax. 1.0 V
13.77
Inactive Battery Voltage- 25mV
68 Throttle Position Sensor signal
(PWM) output
Idle
PulseHi: Battery Voltage
13.37V
Lo: 0 ~ 0.5 V - 25mV
69 Cruise "MAIN" lamp control
output Cruise OFF
DCBattery Voltage
12.37V
Cruise ON Max. 1.0V- 25mV
70 Fuel Pump Relay control output Relay OFF
DCBattery Voltage
12.57V
Relay ON Max. 1.0V- 25mV
71 Variable Intake Solenoid Valve
#1 control output Active
DCMax. 1.0 V
175mV
Inactive Battery Voltage13.77V
72 Immobilizer lamp control output Lamp OFF
DCBattery Voltage
12.77V
Lamp ON Max. 1.0V- 25mV
73 - yy y y
74 - yy y y
75 - yy y y
76 - yy y y
77 - yy y y
78 Purge Control Solenoid Valve
control output Inactive
PulseHi: Battery Voltage
13.83V
Active Lo: Max. 1.0V31.54mV
79 Wheel Speed Sensor [Low]
signal input y
y y y
80 Wheel Speed Sensor [High]
signal input y
y y y
CONNECTOR [C151- 2] Pin
No. Description
ConditionType LevelTest Result
1 ETC Motor [- ] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 125mV
2 ETC Motor [+] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 325mV
3 - yy y y
4 CVVT Oil Temperature Sensor
signal input Idle
Analog 0 ~ 5.0V 282mV at 96°C
5 - yy y y
6 - yy y y
7 Engine Coolant Temperature
Sensor signal input Idle
Analog 0 ~ 5.0V 1.88V

2007 > 2.7L V6 GASOLINE >
INSPECTION
FUNCTION AND OPERATION PRICIPLE
Crankshaft Position Sensor (CKPS) detects the crankshaft position and is one of the most important sensors of the
engine control system. If there is no CKPS signal input, fuel is not supplied and the main relay does not operate. That
is, vehicle can't run without CKPS signal. This sensor is installed on transaxle housing and generates alternating
current by magnetic flux field which is made by the sensor and the target wheel when engine runs. The target wheel
consists of 58 slots and 2 missing slots on 360 CA (Crank Angle).
WAVEFORM
CIRCUIT DIAGRAM

Input signals to TCM(PCM) through ‘CAN communication’
- Engine rpm, TPS signal
- A/CON signal, Engine coolant temperature
- Quantity of intake airflow, Vehicle speed
- Shift holding signal (FTCS ON)
Output signals from TCM(PCM) through ‘CAN communication’
- Request signal for torque reduction
- ATF temperature, TCM(PCM) type, TCM(PCM) error or not
- Damper clutch ON, OFF / Gear position
TCM PIN DESCRIPITION
PIN
No.Check item
Condition Input/Output value
Measurement
Value Remarks
Type Level
A01 2nd CAN_HI -- - --
A02 2nd CAN_LO -- - --
A03 P Range
Selection P Position
OtherwiseDC
Voltage V_BAT
Max. 1.0V 12.9V
0V
A04 R Range
Selection R Position
Otherwise DC
Voltage V_BAT
Max. 1.0V 12.3V
0V
A05 N Range
Selection N Position
Otherwise DC
Voltage V_BAT
Max. 1.0V 13.2V
0V
A06 D Range
Selection D Position
Otherwise DC
Voltage V_BAT
Max. 1.0V 13.2V
0V
A07 Select Position -DC
Voltage V_BAT
Max. 1.0V 13.2V
0V
A08 Up Position -DC
Voltage V_BAT
Max. 1.0V 13.2V
0V
A09 Down Position -DC
Voltage V_BAT
Max. 1.0V 13.2V
0V
A12 N.A -- - -
A14 N.A -- - -
A19 N.A -- - -
A20 A/T Control Relay Relay On
Relay Off
DC
Voltage V_BAT
Max. 1.0V
Vpeak : Max. 70V
Resistance : 680Ω 13.8V
0V
- 0.7V
Resistance : 680Ω
W/H Open DTC Spec : P0890DTC : P0890
A27 Diagnosis "K" Communicated with
GST Pulse At transmitting
HI : V_BAT* 80%↑
LO : V_BATÎ20%↓ AT receiving
HI : V_BAT* 70%↑
LO : V_BAT*30%↓ 11.3V
0.14/ 0.32V V_BAT :
13.2V

Triple pressure switch system
The cause is probably a defective dual pressure switch circuit or a
defective TCM(PCM).a.
Malfunction of the triple pressure switch
b. Malfunction of connector
c. Malfunction of A/C system
d. Malfunction of the TCM(PCM)
Vehicle speed sensor system
The cause is probably a defective vehicle speed sensor circuit or a
defective TCM(PCM). a.
Malfunction of the vehicle speed sensor
b. Malfunction of connector
c. Malfunction of the TCM(PCM)
DTC TROUBLESHOOTING INDEX
No. Code ItemMILRemark
1 P0707 TRANSAXLE RANGE SWITCH CIRCUIT LOW INPUT ON
2 P0708 TRANSAXLE RANGE SWITCH CIRCUIT HIGH INPUT ON
3 P0711 TRANSAXLE FLUID TEMPERATURE SENSOR RATIONALITY ON
4 P0712 TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT LOW INPUT ON
5 P0713 TRANSAXLE FLUID TEMPERATURE SENSOR CIRCUIT HIGH INPUT ON
6 P0717 A/T INPUT SPEED SENSOR CIRCUIT - OPEN or SHORT(GND) ON
7 P0722 AT OUTPUT SPEED SENSOR CIRCUIT - OPEN or SHORT(GND) ON
8 P0731 GEAR 1 INCORRECT RATIO ON
9 P0732 GEAR 2 INCORRECT RATIO ON
10 P0733 GEAR 3 INCORRECT RATIO ON
11 P0734 GEAR 4 INCORRECT RATIO ON
12 P0741 TORQUE CONVERTER CLUTCH STUCK OFF ON
13 P0742 TORQUE CONVERTER CLUTCH STUCK ON ON
14 P0743 TORQUE CONVERTER CLUTCH CONTROL SOLENOID VALVE - OPEN or
SHORT(GND) ON
15 P0748 VFS SOLENOID OFF
16 P0750 LOW and REVERSE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND) ON
17 P0755 UNDER DRIVE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND) ON
18 P0760 SECOND SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND) ON
19 P0765 OVERDRIVE SOLENOID VALVE CIRCUIT - OPEN or SHORT(GND) ON
20 P0885 A/T CONTROL RELAY - OPEN or SHORT(GND) ON
21 P0890 TCM power Relay sense circuit low ON
22 P0891 TCM power Relay sense circuit High ON
Failsafe
Activation and deactivation of error failsafe is coordinated Error failsafe Management.
Once Error failsafe is activated, it will be kept until ignition key OFF.
In every new TCM start, TCM start with No Error failsafe and No Error present.
0. Mechanical Limp Home Mode
a. Switch off A/T relay
1. Electrical Limp Home Mode a. Keep 2nd / 3rd gear
2. Prohibit Intelligent Shift a. Fuzzy SAT(Siements Adaptive Transmission) shift pattern (Medium Driver, Sporty Driver) will not be used

3. Prohibit Adaptive Controla. No learning is done
6. Prohibit Torque Reduction Request a. No torque reduction is sent to ECU
7. Prohibit Lockup Control a. Stay in non- lockup control state
8. Substitute Input Value Oil Temperature a. Set oil temperature(tf) to 80° C (192°F)
9. Substitute Value Speed Ratio a. Set speed ratio to 0.7
10. Substitute CAN Input Value a. Set engine torque to 42 Ë
b. Set throttle position to 50Ë
c. Set accelerator pedal signal to 50 Ë
d. Set engine speed (Ne) to 3000 rpm
e. Set vehicle speed to 0 km/h
f. Set status of air condition relay to OFF
11. Prohibit VFS control a. Stop the Line Pressure Control till IG Off
Failsafe according to the DTC
a.Refer the detail description in the previous page for the indicated number on the ‘Failsafe’ column.
Items Type of errorFailsafeOBD - II
relevant DTC DTC
Oil temperature sensor Short to ground
2, 3, 7, 8, 11P0712
P0712
Open or short to B+ P0713P0713
Stuck signal P0711P0711
Sensor fail P0711P0711
PG- A Short to ground
1,11P0717
P0717
Open or short to B+
PG- B Short to ground
P0722P0722
Open or short to B+
Sensor fail P0721P0721
Brake switch Open
2―P0713
Short to B+
LR Solenoid valve Short to B+
0,11P0750
P0750
Open or short to ground
2nd Solenoid valve Short to B+
P0760P0760
Open or short to ground
UD Solenoid valve Short to B+
P0755P0755
Open or short to ground
OD Solenoid valve Short to B+
P0765P0765
Open or short to ground
Open or short to B+ P0765P0765

DCC Solenoid valveShort to B+
P0743P0743
Open or short to ground
1st speed asynchronous Synchronous error
0,11P0731
P0731
2nd speed asynchronous Synchronous error P0732P0732
3rd speed asynchronous Synchronous error P0733P0733
4th speed asynchronous Synchronous error P0734P0734
Reverse speed asynchronous Synchronous error ――
CAN No ID from ECM
2,3,6,7,9,10,11―
P1604
CAN BUS off ―P1603
Damper clutch Abnormal system 7P0741P0741
A/T relay Short to ground or open 0,11P0885P0885
Inhibitor switch Short to ground or open
―P0707
P0707
Short to B+ or short between switches P0708P0708
VFS Short to B+
11
―P0748
Short to ground 0,11
Open 11
CKP sensor Sensor errorNe=3,000rpm
7,9 ―
―
TPS sensor Sensor errorTPS=50Ë――
SERVICE DATA LIST(WITH SCAN TOOL)
No.ITEM NAME UNITDATA Data Description Failure
1 ENGINE RPM rpm700 rpmCurrent Engine rpm 0 rpm
2 VEHICLE SPEED km/h0km/hCurrent Vehicle speed 0km/h
3 THROTTLE
P.SENSOR %
12.5%Current TPS open angle 0%
4 INPUT SPEED(PG - A) rpm700 rpmInput speed rpm. Always output rpm
when turning start ON 0 rpm
5 OUTPUT SPEED(PG -
B) rpm
0 rpmOutput speed rpm. Always output
rpm when driving 0 rpm
6 DCC(TCC) SOLENOID
DUTY %
0%Control 0%
→ 100% when
operating Damper Clutch
7 DAMPER CLUTCH
SLIP rpm
260 rpmCurrent Damper clutch slip ratio 0 rpm
8 LR SOLENOID DUTY %100%Control 100%
→ 0% when
operating brake 0%
9 UD SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
10 2ND SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
11 OD SOLENOID DUTY %100%Control 100%
→ 0% when
operating clutch 0%
12 VFS SOLENOID DUTY Ë0~400Ë ―

13OIL TEMPERATURE °C40°CCurrent Oil temperature 80°C
14 SHIFT POSITION N,P,REV/1st G/…/5th
G D
Current shift position P, N
15 SELECT LEVEL P,N/R/D/SPORTS DCurrent shift lever position P, N
16 A/CON SWITCH OFF/ON/- /NOT
SUPP OFF
-
17 IDLE STATUS OFF/ON/- /NOT
SUPP ON
When idling, ON
18 BRAKE SWITCH OFF/ON/- /NOT
SUPP ON
When braking, ON
19 AUTO CRUISE
SWITCH OFF/ON/- /NOT
SUPP
20 AUTO CRUISE
RELEASE ―
―
21 SPORT MODE
SELECT SW OFF/ON/- /NOT
SUPP ON
When selecting sport mode, ON
22 SPORT MODE UP SW OFF/ON/- /NOT
SUPP ON
When Selecting Sport mode up, ON
23 SPORT MODE DOWN
SW OFF/ON/- /NOT
SUPP ON
When selecting sport mode down,
ON
24 A/T CONTROL RELAY
VOLT V
12.9V 0V
25 ENGINE TORQUE %20%
26 HIVEC MODE A/B/C/D/E/F/G/H/I/J/K FA/B/C/D is control mode, F is
release mode F
HIVEC - SAT(SIEMENS ADAPTIVE TRANSMISSION CONTROL) Mode (Shift Patten) Shift patten Description(Help)SCAN DISPLAY
ECONOMY Economy Driver shift patten for flat road A
MEDIUM Shift patten for medium road B
SPORTS Shift patten for sport road C
LOAD 1 Shift patten for low land, slow grade and slope D
LOAD 2 Shift patten for low land, steep grade and slope E
LOAD 3 Shift patten for downhill road F
LOAD 1 HI ALT Shift patten for high land, steep grade and slope G
LOAD 2 HI ALT Shift patten for low land, steep grade and slope H
HI TEMP Shift patten for high temperture ATF I
WARM UP Shift patten for exhaust gas decrease J
HOLD Shift patten for when hold, switch on K
Actuator inspection NO ITEM NAME Actuator DrivingCondition
1 LR SOLENOID(SCSV A) 1. IG Key ON
2. Inhibitor SW normal
3. P range
2
UD SOLENOID(SCSV B)