fuel KIA CARNIVAL 2007 Owner's Manual

2007 > 2.7L V6 GASOLINE >
SPECIFICATIONS
FUEL DELIVERY SYSTEM
Items Specification
Fuel Tank Capacity80 lit. (21.1 U.S.gal., 17.6 Imp.gal.)
Fuel Filter (built in Fuel Pump
assembly) Type
High pressure type
Fuel Pressure Regulator (built in
Fuel Pump assembly) Regulated Fuel
Pressure 375 ~ 385 kPa(3.82 ~ 3.92 kgf/cm², 54.3 ~ 55.8 psi)
Fuel Pump Type
Electrical, in - tank type
Driven by Electric motor
SENSORS
MASS AIR FLOW SENSOR (MAFS)
J Type: Hot - film type
J Specification
Air Flow (kg/h) Frequency (Hz)
12.6 kg/h 2,617Hz
18.0 kg/h 2,958Hz
23.4 kg/h 3,241Hz
32.4 kg/h 3,653Hz
43.2 kg/h 4,024Hz
57.6 kg/h 4,399Hz
72.0 kg/h 4,704Hz
108.0 kg/h 5,329Hz
144.0 kg/h 5,897Hz
198.0 kg/h 6,553Hz
270.0 kg/h 7,240Hz
360.0 kg/h 7,957Hz
486.0 kg/h 8,738Hz
666.0 kg/h 9,644Hz
900.0 kg/h 10,590Hz
INTAKE AIR TEMPERATURE SENSOR (IATS)
J Type: Thermistor type
J Specification Temperature Resistance (kΩ)
°C °F
- 40 - 40100.87
- 20 -428.58
0 329.40
10 505.66

Heated oxygen sensor (Bank 2 / Sensor 2) installation3.5 ~ 4.534.3 ~ 44.1 25.3 ~ 32.6
Ignition coil installation bolt 1.0 ~ 1.29.8 ~ 11.8 7.2 ~ 8.7
Knock sensor [Bank 1] installation 1.9 ~ 2.418.6 ~ 23.5 13.7 ~ 17.4
Knock sensor [Bank 2] installation 1.9 ~ 2.418.6 ~ 23.5 13.7 ~ 17.4
Manifold absolute pressure sensor installation bolt 0.8 ~ 1.27.8 ~ 11.8 5.8 ~ 8.7
FUEL DELIVERY SYSTEM Item kgf·mN·mIbf·ft
Fuel tank band mounting nuts 4.0 ~ 5.539.2 ~ 53.9 28.9 ~ 39.8
Fuel pump assembly mounting bolts 0.2 ~ 0.32.0 ~ 2.91.4 ~ 2.2
Delivery pipe installation bolts 0.9 ~ 1.48.8 ~ 13.7 6.5 ~ 10.1
Accelerator pedal module installation bolts 1.3 ~ 1.612.8 ~ 15.7 9.4 ~ 11.6

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
1.Engine is hard to start or does not start at all.
2. Unstable idle.
3. Poor driveability
If any of the above conditions are noted, first perform a routine diagnosis that includes basic engine checks (ignition
system malfunction, incorrect engine adjustment, etc.). Then, inspect the Gasoline Engine Control system components
with the HI- SCAN (Pro).
a. Before removing or installing any part, read the diagnostic trouble codes and then disconnect the battery
negative ( - ) terminal.
b. Before disconnecting the cable from battery terminal, turn the ignition switch to OFF. Removal or connection
of the battery cable during engine operation or while the ignition switch is ON could cause damage to the
ECM.
c. The control harnesses between the ECM and heated oxygen sensor are shielded with the shielded ground
wires to the body in order to prevent the influence of ignition noises and radio interference. When the shielded
wire is faulty, the control harness must be replaced.
d. When checking the generator for the charging state, do not disconnect the battery '+' terminal to prevent the
ECM from damage due to the voltage.
e. When charging the battery with the external charger, disconnect the vehicle side battery terminals to prevent
damage to the ECM.
Malfunction Indicator Lamp (MIL)
Faults with the following items will illuminate the MIL.
a. Catalyst
b. Fuel system
c. Mass Air Flow Sensor (MAFS)
d. Intake Air Temperature Sensor (IATS)
e. Engine Coolant Temperature Sensor (ECTS)
f. Throttle Position Sensor (TPS)
g. Upstream Oxygen Sensor
h. Upstream Oxygen Sensor Heater
i. Downstream Oxygen Sensor
j. Downstream Oxygen Sensor Heater
k. Injector
l. Misfire
m. Crankshaft Position Sensor (CKPS)
n. Camshaft Position Sensor (CMPS)
o. Evaporative Emission Control System
p. Vehicle Speed Sensor (VSS)
q. Idle Speed Control Actuator (ISCA)
r. Power Supply
s. ECM/ PCM
t. MT/AT Encoding
u. Acceleration Sensor
v. MIL- on Request Signal
w. Power Stage
Refer to "INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODES (DTC)" for more information.

23. Variable Intake Solenoid (VIS) #2 Valve (Intake
Manifold Side)24. Fuel Pump Relay
25. Main Relay
27. Wheel Speed Sensor (WSS)
28. Vehicle Speed Sensor (VSS)
31. A/C Pressure Transducer (APT)

28-y
29 -y
30 -y
31 -y
32 A/C Pressure Transducer signal input A/C Pressure Transducer (APT)
33 Sensor ground A/C Pressure Transducer (APT)
34 -y
35 -y
36 -y
37 -y
38 Battery voltage supply after main relay Main Relay
39 Battery voltage supply after main relay Main Relay
40 Battery voltage supply after main relay Main Relay
41 CAN [High] ABS/ESP Control Module
42 CAN [Low] ABS/ESP Control Module
43 Main Relay control output Main Relay
44 Intake Air Temperature Sensor signal input Intake Air Temperature Sensor (IATS)
45 Immobilizer communication line Immobilizer control module
46 -y
47 Mass Air Flow Sensor signal input Mass Air Flow Sensor (MAFS)
48 Sensor ground Accelerator Position Sensor (APS) #2
49 Accelerator Position Sensor #2 signal input Accelerator Position Sensor (APS) #2
50 -y
51 Cruise "SET" lamp control output Cruise "SET" Lamp
52 Vehicle speed signal input ABS/ESP Control Module (With ABS/ESP [Euro -
Ⅲ/Ⅳ])
Vehicle Speed Sensor (VSS) (Except Euro-
Ⅲ/Ⅳ)
53 Sensor ground Intake Air Temperature Sensor (IATS)
54 Accelerator Position Sensor #1 signal input Accelerator Position Sensor (APS) #1
55 Sensor ground Accelerator Position Sensor (APS) #1
56 -y
57 Sensor (+5V) Accelerator Position Sensor (APS) #2
58 Sensor (+5V) A/C Pressure Transducer (APT)
59 Sensor (+5V) Accelerator Position Sensor (APS) #1
60 -y
61 Engine speed signal output Cluster (Tachometer)
62 Fuel consumption signal output Trip Computer
63 Malfunction Indicator Lamp (MIL) control output Cluster (Malfunction Indicator Lamp)
64 A/C Compressor Relay control output A/C Compressor Relay
65 Cooling Fan [Low] control output Cooling Fan Relay [Low]
66 Cooling Fan [High] control output Cooling Fan Relay [High]
67 Variable Intake Solenoid Valve #2 control output Variable Intake Solenoid (VIS) Valve #2 [Intake
Manifold Side]

67Variable Intake Solenoid Valve #2 control output
Manifold Side]
68 Throttle Position Sensor signal (PWM) output ABS/ESP Control Module
69 Cruise "MAIN" lamp control output Cruise "MAIN" Lamp
70 Fuel Pump Relay control output Fuel Pump Relay
71 Variable Intake Solenoid Valve #1 control output Variable Intake Solenoid (VIS) Valve #1 Surge
Tank Side]
72 Immobilizer lamp control output Immobilizer Lamp
73 -y
74 -y
75 -y
76 -y
77 -y
78 Purge Control Solenoid Valve control output Purge Control Solenoid Valve (PCSV)
79 Wheel Speed Sensor [Low] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
80 Wheel Speed Sensor [High] signal input Wheel Speed Sensor (WSS)(Without ABS/ESP
[Euro -
Ⅲ/Ⅳ])
CONNECTOR [C151- 2] Pin
No. Description
Connected to
1 ETC Motor [- ] control output ETC Motor (in ETC Module)
2 ETC Motor [+] control output ETC Motor (in ETC Module)
3 -y
4 CVVT Oil Temperature Sensor signal input CVVT Oil Temperature Sensor (OTS)
5 -y
6 -y
7 Engine Coolant Temperature Sensor signal input Engine Coolant Temperature Sensor (ECTS)
8 Manifold Absolute Pressure Sensor signal input Manifold Absolute Pressure Sensor (MAPS)
9 -y
10 -y
11 Reference voltage (+5V) Manifold Absolute Pressure Sensor (MAPS)
12 Battery voltage supply after ignition switch Ignition Switch
13 Reference voltage (+5V) Throttle Position Sensor (TPS) #2
14 Sensor ground Throttle Position Sensor (TPS) #1
15 Reference voltage (+5V) Camshaft Position Sensor (CMPS) [Bank 2]
16 Reference voltage (+5V) Throttle Position Sensor (TPS) #1
17 Sensor ground Camshaft Position Sensor (CMPS) [Bank 2]
18 Sensor ground Camshaft Position Sensor (CMPS) [Bank 1]
19 Ignition Coil (Cylinder #6) control output Ignition Coil (Cylinder #6)
20 -y
21 Crankshaft Position Sensor [High] signal input Crankshaft Position Sensor (CKPS)
22 -y
Knock Sensor (KS) [Bank 1], Knock Sensor (KS)

40Battery voltage supply after main
relay IG OFF
DCMax. 1.0 V
- 25mV
IG ON Battery Voltage12.37V
41 CAN [High] Recessive
Pulse2.0 ~ 3.0 V
2.4V
Dominant 2.75~4.5 V3.56V
42 CAN [Low] Recessive
Pulse2.0 ~ 3.0 V
2.42V
Dominant 0.5~2.25 V1.62V
43 Main Relay control output Relay ON
DCBattery Voltage
0.875V
Relay OFF Max. 1.0V12.47V
44 Intake Air Temperature Sensor
signal input Idle
Analog 0 ~ 5V 2.05V
45 Immobilizer communication line When
communicating after IG ON PulseHi: Min. 8.5V
11.87V
Lo: Max. 3.5V 875mV
46 - yy y y
47 Mass Air Flow Sensor signal
input
Idle
Pulse Hi: Vcc
4.97V
Lo: Max. 0.5V 70mV
48 Sensor ground IdleDCMax. 50 mV 22.52mV
49 Accelerator Position Sensor #2
signal input C.T
Analog 0.3 ~ 0.9V
0.38V
W.O.T 1.5 ~ 3.0V2V
50 - yy y y
51 Cruise "SET" lamp control output Cruise OFF
DCBattery Voltage
12.57V
Cruise ON Max. 1.0V- 25mV
52 Vehicle speed signal input Vehicle RunPulseHi: Min. 5.0V
11.07V
Lo: Max. 1.0V - 125mV
53 Sensor ground IdleDCMax. 50 mV 22.37mV
54 Accelerator Position Sensor #1
signal input C.T
Analog 0.3 ~ 0.9V
819mV
W.O.T 4.0 ~ 4.8V4.01V
55 Sensor ground IdleDCMax. 50mV 22.6mV
56 - yy y y
57 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
58 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
59 Reference voltage (+5V) IG OFF
DCMax. 0.5V
4.95V
IG ON 4.9 ~ 5.1V- 10mV
60 - yy y y
61 Engine speed signal output IdlePulseHi: Battery Voltage
13.57V
Lo: Max. 0.5V - 25mV
20 ~ 26Hz y
62 Fuel consumption signal output IdlePulseHi: Battery Voltage
13.57V
Lo: Max. 0.5V - 25mV
63 Malfunction Indicator Lamp (MIL)
control output Lamp OFF
DCHi: Battery Voltage
13.37V
Lamp ON Lo: Max. 2.0V- 25mV

64A/C Compressor Relay control
output A/C OFF
DCBattery Voltage
13.97V
A/C ON Max. 1.0V175mV
65 Cooling Fan [Low] control output Fan OFF
DCBattery Voltage
13.77V
Fan ON Max. 1.0V175mV
66 Cooling Fan [High] control output Fan OFF
DCBattery Voltage
13.57V
Fan ON Max. 1.0V- 25mV
67 Variable Intake Solenoid Valve
#2 control output Active
DCMax. 1.0 V
13.77
Inactive Battery Voltage- 25mV
68 Throttle Position Sensor signal
(PWM) output
Idle
PulseHi: Battery Voltage
13.37V
Lo: 0 ~ 0.5 V - 25mV
69 Cruise "MAIN" lamp control
output Cruise OFF
DCBattery Voltage
12.37V
Cruise ON Max. 1.0V- 25mV
70 Fuel Pump Relay control output Relay OFF
DCBattery Voltage
12.57V
Relay ON Max. 1.0V- 25mV
71 Variable Intake Solenoid Valve
#1 control output Active
DCMax. 1.0 V
175mV
Inactive Battery Voltage13.77V
72 Immobilizer lamp control output Lamp OFF
DCBattery Voltage
12.77V
Lamp ON Max. 1.0V- 25mV
73 - yy y y
74 - yy y y
75 - yy y y
76 - yy y y
77 - yy y y
78 Purge Control Solenoid Valve
control output Inactive
PulseHi: Battery Voltage
13.83V
Active Lo: Max. 1.0V31.54mV
79 Wheel Speed Sensor [Low]
signal input y
y y y
80 Wheel Speed Sensor [High]
signal input y
y y y
CONNECTOR [C151- 2] Pin
No. Description
ConditionType LevelTest Result
1 ETC Motor [- ] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 125mV
2 ETC Motor [+] control output IdlePulseHi: Battery Voltage
14.07V
Lo: Max . 1.0V - 325mV
3 - yy y y
4 CVVT Oil Temperature Sensor
signal input Idle
Analog 0 ~ 5.0V 282mV at 96°C
5 - yy y y
6 - yy y y
7 Engine Coolant Temperature
Sensor signal input Idle
Analog 0 ~ 5.0V 1.88V

2007 > 2.7L V6 GASOLINE >
INSPECTION
FUNCTION AND OPERATION PRINCIPLE
Mass Air Flow Sensor (MAFS) is a hot - film type sensor and is located in between the air cleaner and the throttle
body. It consists of a tube, a sensor assembly and honeycomb cell and detects intake air quantity flowing into the
intake manifold. Air flows from the air cleaner assembly through the honeycomb cell and over the hot film element. At
this time, heat transfer is generated by convection and this sensor loses its energy. This sensor detects the mass air
flow by using the energy loss and transfers the information to the PCM by frequency. The PCM calculates fuel quantity
and ignition timing.
SPECIFICATION
Air Flow (kg/h) Output Frequency (Hz)
12.6 kg/h 2,617Hz
18.0 kg/h 2,958Hz
23.4 kg/h 3,241Hz
32.4 kg/h 3,653Hz
43.2 kg/h 4,024Hz
57.6 kg/h 4,399Hz
72.0 kg/h 4,704Hz
108.0 kg/h 5,329Hz
144.0 kg/h 5,897Hz
198.0 kg/h 6,553Hz
270.0 kg/h 7,240Hz
360.0 kg/h 7,957Hz
486.0 kg/h 8,738Hz
666.0 kg/h 9,644Hz
900.0 kg/h 10,590Hz
CIRCUIT DIAGRAM

2007 > 2.7L V6 GASOLINE >
INSPECTION
FUNCTION AND OPERATION PRICIPLE
Engine Coolant Temperature Sensor (ECTS) is located in the engine coolant passage of the cylinder head for
detecting the engine coolant temperature. The ECTS uses a thermistor whose resistance changes with the
temperature. The electrical resistance of the ECTS decreases as the temperature increases, and increases as the
temperature decreases. The reference 5 V in the PCM is supplied to the ECTS via a resistor in the PCM.That is, the
resistor in the PCM and the thermistor in the ECTS are connected in series. When the resistance value of the
thermistor in the ECTS changes according to the engine coolant temperature, the output voltage also changes. During
cold engine operation the PCM increases the fuel injection duration and controls the ignition timing using the
information of engine coolant temperature to avoid engine stalling and improve drivability.
SPECIFICATION
Temperature Resistance(kΩ)
°C °F
- 40 - 4048.14
- 20 -414.13 ~ 16.83
0 325.79
20 682.31 ~ 2.59
40 104 1.15
60 140 0.59
80 176 0.32
CIRCUIT DIAGRAM